------------[ cut here ]------------
WARNING: CPU: 7 PID: 3861 at /home/kernel/ssd/kvm/arch/x86/kvm//vmx.c:11299 nested_vmx_vmexit+0x176e/0x1980 [kvm_intel]
CPU: 7 PID: 3861 Comm: qemu-system-x86 Tainted: G W OE 4.13.0-rc4+ #11
RIP: 0010:nested_vmx_vmexit+0x176e/0x1980 [kvm_intel]
Call Trace:
? kvm_multiple_exception+0x149/0x170 [kvm]
? handle_emulation_failure+0x79/0x230 [kvm]
? load_vmcs12_host_state+0xa80/0xa80 [kvm_intel]
? check_chain_key+0x137/0x1e0
? reexecute_instruction.part.168+0x130/0x130 [kvm]
nested_vmx_inject_exception_vmexit+0xb7/0x100 [kvm_intel]
? nested_vmx_inject_exception_vmexit+0xb7/0x100 [kvm_intel]
vmx_queue_exception+0x197/0x300 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x1b0c/0x2c90 [kvm]
? kvm_arch_vcpu_runnable+0x220/0x220 [kvm]
? preempt_count_sub+0x18/0xc0
? restart_apic_timer+0x17d/0x300 [kvm]
? kvm_lapic_restart_hv_timer+0x37/0x50 [kvm]
? kvm_arch_vcpu_load+0x1d8/0x350 [kvm]
kvm_vcpu_ioctl+0x4e4/0x910 [kvm]
? kvm_vcpu_ioctl+0x4e4/0x910 [kvm]
? kvm_dev_ioctl+0xbe0/0xbe0 [kvm]
The flag "nested_run_pending", which can override the decision of which should run
next, L1 or L2. nested_run_pending=1 means that we *must* run L2 next, not L1. This
is necessary in particular when L1 did a VMLAUNCH of L2 and therefore expects L2 to
be run (and perhaps be injected with an event it specified, etc.). Nested_run_pending
is especially intended to avoid switching to L1 in the injection decision-point.
This can be handled just like the other cases in vmx_check_nested_events, instead of
having a special case in vmx_queue_exception.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vmx_complete_interrupts() assumes that the exception is always injected,
so it can be dropped by kvm_clear_exception_queue(). However,
an exception cannot be injected immediately if it is: 1) originally
destined to a nested guest; 2) trapped to cause a vmexit; 3) happening
right after VMLAUNCH/VMRESUME, i.e. when nested_run_pending is true.
This patch applies to exceptions the same algorithm that is used for
NMIs, replacing exception.reinject with "exception.injected" (equivalent
to nmi_injected).
exception.pending now represents an exception that is queued and whose
side effects (e.g., update RFLAGS.RF or DR7) have not been applied yet.
If exception.pending is true, the exception might result in a nested
vmexit instead, too (in which case the side effects must not be applied).
exception.injected instead represents an exception that is going to be
injected into the guest at the next vmentry.
Reported-by: Radim Krčmář <rkrcmar@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_event_needs_reinjection() encapsulation.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
update_permission_bitmask currently does a 128-iteration loop to,
essentially, compute a constant array. Computing the 8 bits in parallel
reduces it to 16 iterations, and is enough to speed it up substantially
because many boolean operations in the inner loop become constants or
simplify noticeably.
Because update_permission_bitmask is actually the top item in the profile
for nested vmexits, this speeds up an L2->L1 vmexit by about ten thousand
clock cycles, or up to 30%:
before after
cpuid 35173 25954
vmcall 35122 27079
inl_from_pmtimer 52635 42675
inl_from_qemu 53604 44599
inl_from_kernel 38498 30798
outl_to_kernel 34508 28816
wr_tsc_adjust_msr 34185 26818
rd_tsc_adjust_msr 37409 27049
mmio-no-eventfd:pci-mem 50563 45276
mmio-wildcard-eventfd:pci-mem 34495 30823
mmio-datamatch-eventfd:pci-mem 35612 31071
portio-no-eventfd:pci-io 44925 40661
portio-wildcard-eventfd:pci-io 29708 27269
portio-datamatch-eventfd:pci-io 31135 27164
(I wrote a small C program to compare the tables for all values of CR0.WP,
CR4.SMAP and CR4.SMEP, and they match).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch exposes 5 level page table feature to the VM.
At the same time, the canonical virtual address checking is
extended to support both 48-bits and 57-bits address width.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extends the shadow paging code, so that 5 level shadow page
table can be constructed if VM is running in 5 level paging
mode.
Also extends the ept code, so that 5 level ept table can be
constructed if maxphysaddr of VM exceeds 48 bits. Unlike the
shadow logic, KVM should still use 4 level ept table for a VM
whose physical address width is less than 48 bits, even when
the VM is running in 5 level paging mode.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
[Unconditionally reset the MMU context in kvm_cpuid_update.
Changing MAXPHYADDR invalidates the reserved bit bitmasks.
- Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now we have 4 level page table and 5 level page table in 64 bits
long mode, let's rename the PT64_ROOT_LEVEL to PT64_ROOT_4LEVEL,
then we can use PT64_ROOT_5LEVEL for 5 level page table, it's
helpful to make the code more clear.
Also PT64_ROOT_MAX_LEVEL is defined as 4, so that we can just
redefine it to 5 whenever a replacement is needed for 5 level
paging.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, KVM uses CR3_L_MODE_RESERVED_BITS to check the
reserved bits in CR3. Yet the length of reserved bits in
guest CR3 should be based on the physical address width
exposed to the VM. This patch changes CR3 check logic to
calculate the reserved bits at runtime.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Return false in kvm_cpuid() when it fails to find the cpuid
entry. Also, this routine(and its caller) is optimized with
a new argument - check_limit, so that the check_cpuid_limit()
fall back can be avoided.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A guest may not be configured to support XSAVES/XRSTORS, even when the host
does. If the guest does not support XSAVES/XRSTORS, clear the secondary
execution control so that the processor will raise #UD.
Also clear the "allowed-1" bit for XSAVES/XRSTORS exiting in the
IA32_VMX_PROCBASED_CTLS2 MSR, and pass through VMCS12's control in
the VMCS02.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A guest may not be configured to support RDSEED, even when the host
does. If the guest does not support RDSEED, intercept the instruction
and synthesize #UD. Also clear the "allowed-1" bit for RDSEED exiting
in the IA32_VMX_PROCBASED_CTLS2 MSR.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A guest may not be configured to support RDRAND, even when the host
does. If the guest does not support RDRAND, intercept the instruction
and synthesize #UD. Also clear the "allowed-1" bit for RDRAND exiting
in the IA32_VMX_PROCBASED_CTLS2 MSR.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, secondary execution controls are divided in three groups:
- static, depending mostly on the module arguments or the processor
(vmx_secondary_exec_control)
- static, depending on CPUID (vmx_cpuid_update)
- dynamic, depending on nested VMX or local APIC state
Because walking CPUID is expensive, prepare_vmcs02 is using only
the first group. This however is unnecessarily complicated. Just
cache the static secondary execution controls, and then prepare_vmcs02
does not need to compute them every time. Computation of all static
secondary execution controls is now kept in a single function,
vmx_compute_secondary_exec_control.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Enable the Virtual GIF feature. This is done by setting bit 25 at position
60h in the vmcb.
With this feature enabled, the processor uses bit 9 at position 60h as the
virtual GIF when executing STGI/CLGI instructions.
Since the execution of STGI by the L1 hypervisor does not cause a return to
the outermost (L0) hypervisor, the enable_irq_window and enable_nmi_window
are modified.
The IRQ window will be opened even if GIF is not set, under the assumption
that on resuming the L1 hypervisor the IRQ will be held pending until the
processor executes the STGI instruction.
For the NMI window, the STGI intercept is set. This will assist in opening
the window only when GIF=1.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We already always set that type but don't check if it is supported. Also
for nVMX, we only support WB for now. Let's just require it.
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Don't use shifts, tag them correctly as EPTP and use better matching
names (PWL vs. GAW).
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
There is currently some confusion between nested and L1 GPAs. The
assignment to "direct" in kvm_mmu_page_fault tries to fix that, but
it is not enough. What this patch does is fence off the MMIO cache
completely when using shadow nested page tables, since we have neither
a GVA nor an L1 GPA to put in the cache. This also allows some
simplifications in kvm_mmu_page_fault and FNAME(page_fault).
The EPT misconfig likewise does not have an L1 GPA to pass to
kvm_io_bus_write, so that must be skipped for guest mode.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[Changed comment to say "GPAs" instead of "L1's physical addresses", as
per David's review. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
When a guest causes a page fault which requires emulation, the
vcpu->arch.gpa_available flag is set to indicate that cr2 contains a
valid GPA.
Currently, emulator_read_write_onepage() makes use of gpa_available flag
to avoid a guest page walk for a known MMIO regions. Lets not limit
the gpa_available optimization to just MMIO region. The patch extends
the check to avoid page walk whenever gpa_available flag is set.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
[Fix EPT=0 according to Wanpeng Li's fix, plus ensure VMX also uses the
new code. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[Moved "ret < 0" to the else brach, as per David's review. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Calling handle_mmio_page_fault() has been unnecessary since commit
e9ee956e31 ("KVM: x86: MMU: Move handle_mmio_page_fault() call to
kvm_mmu_page_fault()", 2016-02-22).
handle_mmio_page_fault() can now be made static.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Host-initiated writes to the IA32_APIC_BASE MSR do not have to follow
local APIC state transition constraints, but the value written must be
valid.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Bailing out immediately if there is no available mmu page to alloc.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
watchdog: BUG: soft lockup - CPU#5 stuck for 22s! [warn_test:3089]
irq event stamp: 20532
hardirqs last enabled at (20531): [<ffffffff8e9b6908>] restore_regs_and_iret+0x0/0x1d
hardirqs last disabled at (20532): [<ffffffff8e9b7ae8>] apic_timer_interrupt+0x98/0xb0
softirqs last enabled at (8266): [<ffffffff8e9badc6>] __do_softirq+0x206/0x4c1
softirqs last disabled at (8253): [<ffffffff8e083918>] irq_exit+0xf8/0x100
CPU: 5 PID: 3089 Comm: warn_test Tainted: G OE 4.13.0-rc3+ #8
RIP: 0010:kvm_mmu_prepare_zap_page+0x72/0x4b0 [kvm]
Call Trace:
make_mmu_pages_available.isra.120+0x71/0xc0 [kvm]
kvm_mmu_load+0x1cf/0x410 [kvm]
kvm_arch_vcpu_ioctl_run+0x1316/0x1bf0 [kvm]
kvm_vcpu_ioctl+0x340/0x700 [kvm]
? kvm_vcpu_ioctl+0x340/0x700 [kvm]
? __fget+0xfc/0x210
do_vfs_ioctl+0xa4/0x6a0
? __fget+0x11d/0x210
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x23/0xc2
? __this_cpu_preempt_check+0x13/0x20
This can be reproduced readily by ept=N and running syzkaller tests since
many syzkaller testcases don't setup any memory regions. However, if ept=Y
rmode identity map will be created, then kvm_mmu_calculate_mmu_pages() will
extend the number of VM's mmu pages to at least KVM_MIN_ALLOC_MMU_PAGES
which just hide the issue.
I saw the scenario kvm->arch.n_max_mmu_pages == 0 && kvm->arch.n_used_mmu_pages == 1,
so there is one active mmu page on the list, kvm_mmu_prepare_zap_page() fails
to zap any pages, however prepare_zap_oldest_mmu_page() always returns true.
It incurs infinite loop in make_mmu_pages_available() which causes mmu->lock
softlockup.
This patch fixes it by setting the return value of prepare_zap_oldest_mmu_page()
according to whether or not there is mmu page zapped.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's reuse the function introduced with eptp switching.
We don't explicitly have to check against enable_ept_ad_bits, as this
is implicitly done when checking against nested_vmx_ept_caps in
valid_ept_address().
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is the same as commit 147277540b ("kvm: svm: Add support for
additional SVM NPF error codes", 2016-11-23), but for Intel processors.
In this case, the exit qualification field's bit 8 says whether the
EPT violation occurred while translating the guest's final physical
address or rather while translating the guest page tables.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 147277540b ("kvm: svm: Add support for additional SVM NPF error
codes", 2016-11-23) added a new error code to aid nested page fault
handling. The commit unprotects (kvm_mmu_unprotect_page) the page when
we get a NPF due to guest page table walk where the page was marked RO.
However, if an L0->L2 shadow nested page table can also be marked read-only
when a page is read only in L1's nested page table. If such a page
is accessed by L2 while walking page tables it can cause a nested
page fault (page table walks are write accesses). However, after
kvm_mmu_unprotect_page we may get another page fault, and again in an
endless stream.
To cover this use case, we qualify the new error_code check with
vcpu->arch.mmu_direct_map so that the error_code check would run on L1
guest, and not the L2 guest. This avoids hitting the above scenario.
Fixes: 147277540b
Cc: stable@vger.kernel.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported by syzkaller:
The kvm-intel.unrestricted_guest=0
WARNING: CPU: 5 PID: 1014 at /home/kernel/data/kvm/arch/x86/kvm//x86.c:7227 kvm_arch_vcpu_ioctl_run+0x38b/0x1be0 [kvm]
CPU: 5 PID: 1014 Comm: warn_test Tainted: G W OE 4.13.0-rc3+ #8
RIP: 0010:kvm_arch_vcpu_ioctl_run+0x38b/0x1be0 [kvm]
Call Trace:
? put_pid+0x3a/0x50
? rcu_read_lock_sched_held+0x79/0x80
? kmem_cache_free+0x2f2/0x350
kvm_vcpu_ioctl+0x340/0x700 [kvm]
? kvm_vcpu_ioctl+0x340/0x700 [kvm]
? __fget+0xfc/0x210
do_vfs_ioctl+0xa4/0x6a0
? __fget+0x11d/0x210
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x23/0xc2
? __this_cpu_preempt_check+0x13/0x20
The syszkaller folks reported a residual mmio emulation request to userspace
due to vm86 fails to emulate inject real mode interrupt(fails to read CS) and
incurs a triple fault. The vCPU returns to userspace with vcpu->mmio_needed == true
and KVM_EXIT_SHUTDOWN exit reason. However, the syszkaller testcase constructs
several threads to launch the same vCPU, the thread which lauch this vCPU after
the thread whichs get the vcpu->mmio_needed == true and KVM_EXIT_SHUTDOWN will
trigger the warning.
#define _GNU_SOURCE
#include <pthread.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <sys/wait.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/mman.h>
#include <fcntl.h>
#include <unistd.h>
#include <linux/kvm.h>
#include <stdio.h>
int kvmcpu;
struct kvm_run *run;
void* thr(void* arg)
{
int res;
res = ioctl(kvmcpu, KVM_RUN, 0);
printf("ret1=%d exit_reason=%d suberror=%d\n",
res, run->exit_reason, run->internal.suberror);
return 0;
}
void test()
{
int i, kvm, kvmvm;
pthread_t th[4];
kvm = open("/dev/kvm", O_RDWR);
kvmvm = ioctl(kvm, KVM_CREATE_VM, 0);
kvmcpu = ioctl(kvmvm, KVM_CREATE_VCPU, 0);
run = (struct kvm_run*)mmap(0, 4096, PROT_READ|PROT_WRITE, MAP_SHARED, kvmcpu, 0);
srand(getpid());
for (i = 0; i < 4; i++) {
pthread_create(&th[i], 0, thr, 0);
usleep(rand() % 10000);
}
for (i = 0; i < 4; i++)
pthread_join(th[i], 0);
}
int main()
{
for (;;) {
int pid = fork();
if (pid < 0)
exit(1);
if (pid == 0) {
test();
exit(0);
}
int status;
while (waitpid(pid, &status, __WALL) != pid) {}
}
return 0;
}
This patch fixes it by resetting the vcpu->mmio_needed once we receive
the triple fault to avoid the residue.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
get_cpl requires vcpu_load, so we must cache the result (whether the
vcpu was preempted when its cpl=0) in kvm_vcpu_arch.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a vcpu exits due to request a user mode spinlock, then
the spinlock-holder may be preempted in user mode or kernel mode.
(Note that not all architectures trap spin loops in user mode,
only AMD x86 and ARM/ARM64 currently do).
But if a vcpu exits in kernel mode, then the holder must be
preempted in kernel mode, so we should choose a vcpu in kernel mode
as a more likely candidate for the lock holder.
This introduces kvm_arch_vcpu_in_kernel() to decide whether the
vcpu is in kernel-mode when it's preempted. kvm_vcpu_on_spin's
new argument says the same of the spinning VCPU.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add guest_cpuid_clear() and use it instead of kvm_find_cpuid_entry().
Also replace some uses of kvm_find_cpuid_entry() with guest_cpuid_has().
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch turns guest_cpuid_has_XYZ(cpuid) into guest_cpuid_has(cpuid,
X86_FEATURE_XYZ), which gets rid of many very similar helpers.
When seeing a X86_FEATURE_*, we can know which cpuid it belongs to, but
this information isn't in common code, so we recreate it for KVM.
Add some BUILD_BUG_ONs to make sure that it runs nicely.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
bit(X86_FEATURE_NRIPS) is 3 since 2ccd71f1b2 ("x86/cpufeature: Move
some of the scattered feature bits to x86_capability"), so we can
simplify the code.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When L2 uses vmfunc, L0 utilizes the associated vmexit to
emulate a switching of the ept pointer by reloading the
guest MMU.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Expose VMFUNC in MSRs and VMCS fields. No actual VMFUNCs are enabled.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Enable VMFUNC in the secondary execution controls. This simplifies the
changes necessary to expose it to nested hypervisors. VMFUNCs still
cause #UD when invoked.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Let's also just use the underlying functions directly here.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
[Rebased on top of 9f744c5974 ("KVM: nVMX: do not pin the VMCS12")]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
nested_get_page() just sounds confusing. All we want is a page from G1.
This is even unrelated to nested.
Let's introduce kvm_vcpu_gpa_to_page() so we don't get too lengthy
lines.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[Squash pasto fix from Wanpeng Li. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose the "Enable INVPCID" secondary execution control to the guest
and properly reflect the exit reason.
In addition, before this patch the guest was always running with
INVPCID enabled, causing pcid.flat's "Test on INVPCID when disabled"
test to fail.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It has been experimentally confirmed that supporting these two MSRs is one
of the necessary conditions for nested Hyper-V to use the TSC page. Modern
Windows guests are noticeably slower when they fall back to reading
timestamps from the HV_X64_MSR_TIME_REF_COUNT MSR instead of using the TSC
page.
The newly supported MSRs are advertised with the AccessFrequencyRegs
partition privilege flag and CPUID.40000003H:EDX[8] "Support for
determining timer frequencies is available" (both outside of the scope of
this KVM patch).
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
------------[ cut here ]------------
WARNING: CPU: 5 PID: 2288 at arch/x86/kvm/vmx.c:11124 nested_vmx_vmexit+0xd64/0xd70 [kvm_intel]
CPU: 5 PID: 2288 Comm: qemu-system-x86 Not tainted 4.13.0-rc2+ #7
RIP: 0010:nested_vmx_vmexit+0xd64/0xd70 [kvm_intel]
Call Trace:
vmx_check_nested_events+0x131/0x1f0 [kvm_intel]
? vmx_check_nested_events+0x131/0x1f0 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x5dd/0x1be0 [kvm]
? vmx_vcpu_load+0x1be/0x220 [kvm_intel]
? kvm_arch_vcpu_load+0x62/0x230 [kvm]
kvm_vcpu_ioctl+0x340/0x700 [kvm]
? kvm_vcpu_ioctl+0x340/0x700 [kvm]
? __fget+0xfc/0x210
do_vfs_ioctl+0xa4/0x6a0
? __fget+0x11d/0x210
SyS_ioctl+0x79/0x90
do_syscall_64+0x8f/0x750
? trace_hardirqs_on_thunk+0x1a/0x1c
entry_SYSCALL64_slow_path+0x25/0x25
This can be reproduced by booting L1 guest w/ 'noapic' grub parameter, which
means that tells the kernel to not make use of any IOAPICs that may be present
in the system.
Actually external_intr variable in nested_vmx_vmexit() is the req_int_win
variable passed from vcpu_enter_guest() which means that the L0's userspace
requests an irq window. I observed the scenario (!kvm_cpu_has_interrupt(vcpu) &&
L0's userspace reqeusts an irq window) is true, so there is no interrupt which
L1 requires to inject to L2, we should not attempt to emualte "Acknowledge
interrupt on exit" for the irq window requirement in this scenario.
This patch fixes it by not attempt to emulate "Acknowledge interrupt on exit"
if there is no L1 requirement to inject an interrupt to L2.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
[Added code comment to make it obvious that the behavior is not correct.
We should do a userspace exit with open interrupt window instead of the
nested VM exit. This patch still improves the behavior, so it was
accepted as a (temporary) workaround.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The host physical addresses of L1's Virtual APIC Page and Posted
Interrupt descriptor are loaded into the VMCS02. The CPU may write
to these pages via their host physical address while L2 is running,
bypassing address-translation-based dirty tracking (e.g. EPT write
protection). Mark them dirty on every exit from L2 to prevent them
from getting out of sync with dirty tracking.
Also mark the virtual APIC page and the posted interrupt descriptor
dirty when KVM is virtualizing posted interrupt processing.
Signed-off-by: David Matlack <dmatlack@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
According to the Intel SDM, software cannot rely on the current VMCS to be
coherent after a VMXOFF or shutdown. So this is a valid way to handle VMCS12
flushes.
24.11.1 Software Use of Virtual-Machine Control Structures
...
If a logical processor leaves VMX operation, any VMCSs active on
that logical processor may be corrupted (see below). To prevent
such corruption of a VMCS that may be used either after a return
to VMX operation or on another logical processor, software should
execute VMCLEAR for that VMCS before executing the VMXOFF instruction
or removing power from the processor (e.g., as part of a transition
to the S3 and S4 power states).
...
This fixes a "suspicious rcu_dereference_check() usage!" warning during
kvm_vm_release() because nested_release_vmcs12() calls
kvm_vcpu_write_guest_page() without holding kvm->srcu.
Signed-off-by: David Matlack <dmatlack@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Since the current implementation of VMCS12 does a memcpy in and out
of guest memory, we do not need current_vmcs12 and current_vmcs12_page
anymore. current_vmptr is enough to read and write the VMCS12.
And David Matlack noted:
This patch also fixes dirty tracking (memslot->dirty_bitmap) of the
VMCS12 page by using kvm_write_guest. nested_release_page() only marks
the struct page dirty.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[Added David Matlack's note and nested_release_page_clean() fix.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
'lapic_irq' is a local variable and its 'level' field isn't
initialized, so 'level' is random, it doesn't matter but
makes UBSAN unhappy:
UBSAN: Undefined behaviour in .../lapic.c:...
load of value 10 is not a valid value for type '_Bool'
...
Call Trace:
[<ffffffff81f030b6>] dump_stack+0x1e/0x20
[<ffffffff81f03173>] ubsan_epilogue+0x12/0x55
[<ffffffff81f03b96>] __ubsan_handle_load_invalid_value+0x118/0x162
[<ffffffffa1575173>] kvm_apic_set_irq+0xc3/0xf0 [kvm]
[<ffffffffa1575b20>] kvm_irq_delivery_to_apic_fast+0x450/0x910 [kvm]
[<ffffffffa15858ea>] kvm_irq_delivery_to_apic+0xfa/0x7a0 [kvm]
[<ffffffffa1517f4e>] kvm_emulate_hypercall+0x62e/0x760 [kvm]
[<ffffffffa113141a>] handle_vmcall+0x1a/0x30 [kvm_intel]
[<ffffffffa114e592>] vmx_handle_exit+0x7a2/0x1fa0 [kvm_intel]
...
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
When SMP VM start, AP may lost INIT because of receiving INIT between
kvm_vcpu_ioctl_x86_get/set_vcpu_events.
vcpu 0 vcpu 1
kvm_vcpu_ioctl_x86_get_vcpu_events
events->smi.latched_init = 0
send INIT to vcpu1
set vcpu1's pending_events
kvm_vcpu_ioctl_x86_set_vcpu_events
if (events->smi.latched_init == 0)
clear INIT in pending_events
This patch fixes it by just update SMM related flags if we are in SMM.
Thanks Peng Hao for the report and original commit message.
Reported-by: Peng Hao <peng.hao2@zte.com.cn>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
There are three issues in nested_vmx_check_exception:
1) it is not taking PFEC_MATCH/PFEC_MASK into account, as reported
by Wanpeng Li;
2) it should rebuild the interruption info and exit qualification fields
from scratch, as reported by Jim Mattson, because the values from the
L2->L0 vmexit may be invalid (e.g. if an emulated instruction causes
a page fault, the EPT misconfig's exit qualification is incorrect).
3) CR2 and DR6 should not be written for exception intercept vmexits
(CR2 only for AMD).
This patch fixes the first two and adds a comment about the last,
outlining the fix.
Cc: Jim Mattson <jmattson@google.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Do this in the caller of nested_vmx_vmexit instead.
nested_vmx_check_exception was doing a vmwrite to the vmcs02's
VM_EXIT_INTR_ERROR_CODE field, so that prepare_vmcs12 would move
the field to vmcs12->vm_exit_intr_error_code. However that isn't
possible on pre-Haswell machines. Moving the vmcs12 write to the
callers fixes it.
Reported-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[Changed nested_vmx_reflect_vmexit() return type to (int)1 from (bool)1,
thanks to fengguang.wu@intel.com]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Run kvm-unit-tests/eventinj.flat in L1 w/ ept=0 on both L0 and L1:
Before NMI IRET test
Sending NMI to self
NMI isr running stack 0x461000
Sending nested NMI to self
After nested NMI to self
Nested NMI isr running rip=40038e
After iret
After NMI to self
FAIL: NMI
Commit 4c4a6f790e (KVM: nVMX: track NMI blocking state separately
for each VMCS) tracks NMI blocking state separately for vmcs01 and
vmcs02. However it is not enough:
- The L2 (kvm-unit-tests/eventinj.flat) generates NMI that will fault
on IRET, so the L2 can generate #PF which can be intercepted by L0.
- L0 walks L1's guest page table and sees the mapping is invalid, it
resumes the L1 guest and injects the #PF into L1. At this point the
vmcs02 has nmi_known_unmasked=true.
- L1 sets set bit 3 (blocking by NMI) in the interruptibility-state field
of vmcs12 (and fixes the shadow page table) before resuming L2 guest.
- L1 executes VMRESUME to resume L2, causing a vmexit to L0
- during VMRESUME emulation, prepare_vmcs02 sets bit 3 in the
interruptibility-state field of vmcs02, but nmi_known_unmasked is
still true.
- L2 immediately exits to L0 with another page fault, because L0 still has
not updated the NGVA->HPA page tables. However, nmi_known_unmasked is
true so vmx_recover_nmi_blocking does not do anything.
The fix is to update nmi_known_unmasked when preparing vmcs02 from vmcs12.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The PI vector for L0 and L1 must be different. If dest vcpu0
is in guest mode while vcpu1 is delivering a non-nested PI to
vcpu0, there wont't be any vmexit so that the non-nested interrupt
will be delayed.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
