nd_iostat_start() and nd_iostat_end() implement the same functionality
that generic_start_io_acct() and generic_end_io_acct() already provide.
Change nd_iostat_start() and nd_iostat_end() to call the generic iostat
interfaces. There is no change in the nd interfaces.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
nvdimm_clear_poison cleared the user-visible badblocks, and sent
commands to the NVDIMM to clear the areas marked as 'poison', but it
neglected to clear the same areas from the internal poison_list which is
used to marshal ARS results before sorting them by namespace. As a
result, once on-demand ARS functionality was added:
37b137f nfit, libnvdimm: allow an ARS scrub to be triggered on demand
A scrub triggered from either sysfs or an MCE was found to be adding
stale entries that had been cleared from gendisk->badblocks, but were
still present in nvdimm_bus->poison_list. Additionally, the stale entries
could be triggered into producing stale disk->badblocks by simply disabling
and re-enabling the namespace or region.
This adds the missing step of clearing poison_list entries when clearing
poison, so that it is always in sync with badblocks.
Fixes: 37b137f ("nfit, libnvdimm: allow an ARS scrub to be triggered on demand")
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The internal alloc_nvdimm_map() helper might fail, particularly if the
memory region is already busy. Report request_mem_region() failures and
check for the failure.
Reported-by: Ryan Chen <ryan.chan105@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Normally, an ARS (Address Range Scrub) only happens at
boot/initialization time. There can however arise situations where a
bus-wide rescan is needed - notably, in the case of discovering a latent
media error, we should do a full rescan to figure out what other sectors
are bad, and thus potentially avoid triggering an mce on them in the
future. Also provide a sysfs trigger to start a bus-wide scrub.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A recent effort to add a new nvdimm bus provider attribute highlighted a
race between interrogating nvdimm_bus->nd_desc and nvdimm_bus tear down.
The typical way to handle these races is to take the device_lock() in
the attribute method and validate that the device is still active. In
order for a device to be 'active' it needs to be associated with a
driver. So, we create the small boilerplate for a driver and register
nvdimm_bus devices on the 'nvdimm_bus_type' bus.
A result of this change is that ndbusX devices now appear under
/sys/bus/nd/devices. In fact this makes /sys/class/nd somewhat
redundant, but removing that will need to take a long deprecation period
given its use by ndctl binaries in the field.
This change naturally pulls code from drivers/nvdimm/core.c to
drivers/nvdimm/bus.c, so it is a nice code organization clean-up as
well.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Let the provider module be explicitly passed in rather than implicitly
assumed by the module that calls nvdimm_bus_register(). This is in
preparation for unifying the nfit and nfit_test driver teardown paths.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for generically mapping flush hint addresses for both the
BLK and PMEM use case, provide a generic / reference counted mapping
api. Given the fact that a dimm may belong to multiple regions (PMEM
and BLK), the flush hint addresses need to be held valid as long as any
region associated with the dimm is active. This is similar to the
existing BLK-region case where multiple BLK-regions may share an
aperture mapping. Up-level this shared / reference-counted mapping
capability from the nfit driver to a core nvdimm capability.
This eliminates the need for the nd_blk_region.disable() callback. Note
that the removal of nfit_spa_map() and related infrastructure is
deferred to a later patch.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Initialize struct blk_integrity with 0 as blk_integrity_register() takes the
then unitialized struct blk_integrity::flags and ORs it to the resulting block
integrity structure.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ida instances allocate some internal memory for ->free_bitmap in
addition to the base 'struct ida'. Use ida_destroy() to release that
memory at module_exit().
Reported-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Clarify the distinction between "commands", the ioctls userspace calls
to request the kernel take some action on a given dimm device, and
"_DSMs", the actual function numbers used in the firmware interface to
the DIMM. _DSMs are ACPI specific whereas commands are Linux kernel
generic.
This is in preparation for breaking the 1:1 implicit relationship
between the kernel ioctl number space and the firmware specific function
numbers.
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When section alignment padding is in effect we need to shift / truncate
the range that is queried for poison by the 'start_pad' or 'end_trunc'
reservations.
It's easiest if we just pass in an adjusted resource range rather than
deriving it from the passed in namespace. With the resource range
resolution pushed out to the caller we can also push the
namespace-to-region lookup to the caller and drop the implicit pmem-type
assumption about the passed in namespace object.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Introduce a workqueue that will be used to run address range scrub
asynchronously with the rest of nvdimm device probing.
Userspace still wants notification when probing operations complete, so
introduce a new callback to flush this workqueue when userspace is
awaiting probe completion.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for making poison list retrieval asynchronus to region
registration, add protection for walking and mutating the bus-level
poison list.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If a device will ever have badblocks it should always have a badblocks
instance available. So, similar to md, embed a badblocks instance in
pmem_device. This reduces pointer chasing in the i/o fast path, and
simplifies the init path.
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If the badblocks list runs out of space it simply means that software is
unable to intercept all errors. This is no different than the latent
discovery of new badblocks case and should not be an initialization
failure condition.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
During region creation, perform Address Range Scrubs (ARS) for the SPA
(System Physical Address) ranges to retrieve known poison locations from
firmware. Add a new data structure 'nd_poison' which is used as a list
in nvdimm_bus to store these poison locations.
When creating a pmem namespace, if there is any known poison associated
with its physical address space, convert the poison ranges to bad sectors
that are exposed using the badblocks interface.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The libnvidmm-btt and nvme drivers use blk_integrity to reserve space
for per-sector metadata, but sometimes without protection checksums.
This property is generically useful, so teach the block core to
internally specify a nop profile if one is not provided at registration
time.
Cc: Keith Busch <keith.busch@intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
[hch: kill the local nvme nop profile as well]
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Up until now the_integrity profile has been dynamically allocated and
attached to struct gendisk after the disk has been made active.
This causes problems because NVMe devices need to register the profile
prior to the partition table being read due to a mandatory metadata
buffer requirement. In addition, DM goes through hoops to deal with
preallocating, but not initializing integrity profiles.
Since the integrity profile is small (4 bytes + a pointer), Christoph
suggested moving it to struct gendisk proper. This requires several
changes:
- Moving the blk_integrity definition to genhd.h.
- Inlining blk_integrity in struct gendisk.
- Removing the dynamic allocation code.
- Adding helper functions which allow gendisk to set up and tear down
the integrity sysfs dir when a disk is added/deleted.
- Adding a blk_integrity_revalidate() callback for updating the stable
pages bdi setting.
- The calls that depend on whether a device has an integrity profile or
not now key off of the bi->profile pointer.
- Simplifying the integrity support routines in DM (Mike Snitzer).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We previously made a complete copy of a device's data integrity profile
even though several of the fields inside the blk_integrity struct are
pointers to fixed template entries in t10-pi.c.
Split the static and per-device portions so that we can reference the
template directly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is disabled by default as the overhead is prohibitive, but if the
user takes the action to turn it on we'll oblige.
Reviewed-by: Vishal Verma <vishal.l.verma@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Support multiple block sizes (sector + metadata) for nd_blk in the
same way as done for the BTT. Add the idea of an 'internal' lbasize,
which is properly aligned and padded, and store metadata in this space.
Signed-off-by: Vishal Verma <vishal.l.verma@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Support multiple block sizes (sector + metadata) using the blk integrity
framework. This registers a new integrity template that defines the
protection information tuple size based on the configured metadata size,
and simply acts as a passthrough for protection information generated by
another layer. The metadata is written to the storage as-is, and read back
with each sector.
Signed-off-by: Vishal Verma <vishal.l.verma@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A blk label set describes a namespace comprised of one or more
discontiguous dpa ranges on a single dimm. They may alias with one or
more pmem interleave sets that include the given dimm.
This is the runtime/volatile configuration infrastructure for sysfs
manipulation of 'alt_name', 'uuid', 'size', and 'sector_size'. A later
patch will make these settings persistent by writing back the label(s).
Unlike pmem namespaces, multiple blk namespaces can be created per
region. Once a blk namespace has been created a new seed device
(unconfigured child of a parent blk region) is instantiated. As long as
a region has 'available_size' != 0 new child namespaces may be created.
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Neil Brown <neilb@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A complete label set is a PMEM-label per-dimm per-interleave-set where
all the UUIDs match and the interleave set cookie matches the hosting
interleave set.
Present sysfs attributes for manipulation of a PMEM-namespace's
'alt_name', 'uuid', and 'size' attributes. A later patch will make
these settings persistent by writing back the label.
Note that PMEM allocations grow forwards from the start of an interleave
set (lowest dimm-physical-address (DPA)). BLK-namespaces that alias
with a PMEM interleave set will grow allocations backward from the
highest DPA.
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Neil Brown <neilb@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
On platforms that have firmware support for reading/writing per-dimm
label space, a portion of the dimm may be accessible via an interleave
set PMEM mapping in addition to the dimm's BLK (block-data-window
aperture(s)) interface. A label, stored in a "configuration data
region" on the dimm, disambiguates which dimm addresses are accessed
through which exclusive interface.
Add infrastructure that allows the kernel to block modifications to a
label in the set while any member dimm is active. Note that this is
meant only for enforcing "no modifications of active labels" via the
coarse ioctl command. Adding/deleting namespaces from an active
interleave set is always possible via sysfs.
Another aspect of tracking interleave sets is tracking their integrity
when DIMMs in a set are physically re-ordered. For this purpose we
generate an "interleave-set cookie" that can be recorded in a label and
validated against the current configuration. It is the bus provider
implementation's responsibility to calculate the interleave set cookie
and attach it to a given region.
Cc: Neil Brown <neilb@suse.de>
Cc: <linux-acpi@vger.kernel.org>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The libnvdimm region driver is an intermediary driver that translates
non-volatile "region"s into "namespace" sub-devices that are surfaced by
persistent memory block-device drivers (PMEM and BLK).
ACPI 6 introduces the concept that a given nvdimm may simultaneously
offer multiple access modes to its media through direct PMEM load/store
access, or windowed BLK mode. Existing nvdimms mostly implement a PMEM
interface, some offer a BLK-like mode, but never both as ACPI 6 defines.
If an nvdimm is single interfaced, then there is no need for dimm
metadata labels. For these devices we can take the region boundaries
directly to create a child namespace device (nd_namespace_io).
Acked-by: Christoph Hellwig <hch@lst.de>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* Implement the device-model infrastructure for loading modules and
attaching drivers to nvdimm devices. This is a simple association of a
nd-device-type number with a driver that has a bitmask of supported
device types. To facilitate userspace bind/unbind operations 'modalias'
and 'devtype', that also appear in the uevent, are added as generic
sysfs attributes for all nvdimm devices. The reason for the device-type
number is to support sub-types within a given parent devtype, be it a
vendor-specific sub-type or otherwise.
* The first consumer of this infrastructure is the driver
for dimm devices. It simply uses control messages to retrieve and
store the configuration-data image (label set) from each dimm.
Note: nd_device_register() arranges for asynchronous registration of
nvdimm bus devices by default.
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Neil Brown <neilb@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Most discovery/configuration of the nvdimm-subsystem is done via sysfs
attributes. However, some nvdimm_bus instances, particularly the
ACPI.NFIT bus, define a small set of messages that can be passed to the
platform. For convenience we derive the initial libnvdimm-ioctl command
formats directly from the NFIT DSM Interface Example formats.
ND_CMD_SMART: media health and diagnostics
ND_CMD_GET_CONFIG_SIZE: size of the label space
ND_CMD_GET_CONFIG_DATA: read label space
ND_CMD_SET_CONFIG_DATA: write label space
ND_CMD_VENDOR: vendor-specific command passthrough
ND_CMD_ARS_CAP: report address-range-scrubbing capabilities
ND_CMD_ARS_START: initiate scrubbing
ND_CMD_ARS_STATUS: report on scrubbing state
ND_CMD_SMART_THRESHOLD: configure alarm thresholds for smart events
If a platform later defines different commands than this set it is
straightforward to extend support to those formats.
Most of the commands target a specific dimm. However, the
address-range-scrubbing commands target the bus. The 'commands'
attribute in sysfs of an nvdimm_bus, or nvdimm, enumerate the supported
commands for that object.
Cc: <linux-acpi@vger.kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Enable nvdimm devices to be registered on a nvdimm_bus. The kernel
assigned device id for nvdimm devicesis dynamic. If userspace needs a
more static identifier it should consult a provider-specific attribute.
In the case where NFIT is the provider, the 'nmemX/nfit/handle' or
'nmemX/nfit/serial' attributes may be used for this purpose.
Cc: Neil Brown <neilb@suse.de>
Cc: <linux-acpi@vger.kernel.org>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The control device for a nvdimm_bus is registered as an "nd" class
device. The expectation is that there will usually only be one "nd" bus
registered under /sys/class/nd. However, we allow for the possibility
of multiple buses and they will listed in discovery order as
ndctl0...ndctlN. This character device hosts the ioctl for passing
control messages. The initial command set has a 1:1 correlation with
the commands listed in the by the "NFIT DSM Example" document [1], but
this scheme is extensible to future command sets.
Note, nd_ioctl() and the backing ->ndctl() implementation are defined in
a subsequent patch. This is simply the initial registrations and sysfs
attributes.
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
Cc: Neil Brown <neilb@suse.de>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: <linux-acpi@vger.kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A struct nvdimm_bus is the anchor device for registering nvdimm
resources and interfaces, for example, a character control device,
nvdimm devices, and I/O region devices. The ACPI NFIT (NVDIMM Firmware
Interface Table) is one possible platform description for such
non-volatile memory resources in a system. The nfit.ko driver attaches
to the "ACPI0012" device that indicates the presence of the NFIT and
parses the table to register a struct nvdimm_bus instance.
Cc: <linux-acpi@vger.kernel.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
