During hotplug, it is possible for 6Gbps link speed to be limited all
the way down to 1.5 Gbps which may lead to a slower link speed when
drive is re-connected.
This behavior has been seen on a Intel Lewisburg SATA controller
(8086:a1d2) with HGST HUH728080ALE600 drive where SATA link speed was
limited to 1.5 Gbps and when re-connected the link came up 3.0 Gbps.
This patch was retested on above configuration and showed the
hotplugged link to come back online at max speed (6Gbps). I did not
see the downgrade when testing on Intel C600/X79, but retested patched
linux-4.14-rc5 kernel and didn't see any side effects from this
change. Also, successfully retested hotplug on port multiplier 3Gbps
link.
tj: Minor comment updates.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Nothing too interesting or alarming. Other than a new power saving
mode addition to ahci and crash fix on a tracepoint, all changes are
trivial or device-specific"
* 'for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ahci: imx: Handle increased read failures for IMX53 temperature sensor in low frequency mode.
ata: sata_dwc_460ex: Propagate platform device ID to DMA driver
ata: fixes kernel crash while tracing ata_eh_link_autopsy event
ata: pata_pdc2027x: Fix space before '[' error.
libata: fix spelling mistake: 'ambigious' -> 'ambiguous'
ata: ceva: Add SMMU support for SATA IP
ata: ceva: Correct the suspend and resume logic for SATA
ata: ceva: Correct the AXI bus configuration for SATA ports
ata: ceva: Add CCI support for SATA if CCI is enabled
ata: ceva: Make RxWaterMark value as module parameter
ata: ceva: Disable Device Sleep capability
ata: ceva: Add gen 3 mode support in driver
ata: ceva: Move sata port phy oob settings to device-tree
devicetree: bindings: Add sata port phy config parameters in ahci-ceva
ata: mark expected switch fall-throughs
ata: sata_mv: remove a redundant assignment to pointer ehi
ahci: Add support for Cavium's fifth generation SATA controller
ata: sata_rcar: Use of_device_get_match_data() helper
libata: make ata_port_type const
libata: make static arrays const, reduces object code size
...
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
In cases where a "drop through" comment was already in place, I replaced
it with a proper "fall through" comment, which is what GCC is expecting
to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Link: https://lkml.kernel.org/r/20171005004842.GA23011@beast
Make this const as it is only stored in the const field of a device
structure. Make the declaration in header const too.
Structure found using Coccinelle and changes done by hand.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As described by Matthew Garret quite a while back:
https://mjg59.dreamwidth.org/34868.html
Intel CPUs starting with the Haswell generation need SATA links to power
down for the "package" part of the CPU to reach low power-states like
PC7 / P8 which bring a significant power-saving with them.
The default max_performance lpm policy does not allow for these high
PC states, both the medium_power and min_power policies do allow this.
The min_power policy saves significantly more power, but there are some
reports of some disks / SSDs not liking min_power leading to system
crashes and in some cases even data corruption has been reported.
Matthew has found a document documenting the default settings of
Intel's IRST Windows driver with which most laptops ship:
https://www-ssl.intel.com/content/dam/doc/reference-guide/sata-devices-implementation-recommendations.pdf
Matthew wrote a patch changing med_power to match those defaults, but
that never got anywhere as some people where reporting issues with the
patch-set that patch was a part of.
This commit is another attempt to make the default IRST driver settings
available under Linux, but instead of changing medium_power and
potentially introducing regressions, this commit adds a new
med_power_with_dipm setting which is identical to the existing
medium_power accept that it enables dipm on top, which makes it match
the Windows IRST driver settings, which should hopefully be safe to
use on most devices.
The med_power_with_dipm setting is close to min_power, except that:
a) It does not use host-initiated slumber mode (ASP not set),
but it does allow device-initiated slumber
b) It does not enable DevSlp mode
On my T440s test laptop I get the following power savings when idle:
medium_power 0.9W
med_power_with_dipm 1.2W
min_power 1.2W
Suggested-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
gcc-7 warns about the result of a constant multiplication used as
a boolean:
drivers/ata/libata-core.c: In function 'ata_timing_quantize':
drivers/ata/libata-core.c:3164:30: warning: '*' in boolean context, suggest '&&' instead [-Wint-in-bool-context]
This slightly rearranges the macro to simplify the code and avoid
the warning at the same time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 35f0b6a779.
We now conditionalize issuing of READ LOG PAGE on the TRUSTED
COMPUTING SUPPORTED bit in the identity data and this shouldn't be
necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
ATA-8 and later mirrors the TRUSTED COMPUTING SUPPORTED bit in word 48 of
the IDENTIFY DEVICE data. Check this before issuing a READ LOG PAGE
command to avoid issues with buggy devices. The only downside is that
we can't support Security Send / Receive for a device with an older
revision due to the conflicting use of this field in earlier
specifications.
tj: The reason we need this is because some devices which don't
support READ LOG PAGE lock up after getting issued that command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ido reported that reading the log page on his systems fails,
so quirk it as it won't support ZBC or security protocols.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The warning message "READ LOG DMA EXT failed, trying unqueued" in
ata_read_log_page() as well as the macro name ATA_HORKAGE_NO_NCQ_LOG
are confusing: the command READ LOG DMA EXT is not an queued NCQ command
unless it is encapsulated in a RECEIVE FPDMA QUEUED command.
From ACS-4 READ LOG DMA EXT description:
"The device processes the READ LOG DMA EXT command in the NCQ feature
set environment (see 4.13.6) if the READ LOG DMA EXT command is
encapsulated in a RECEIVE FPDMA QUEUED command (see 7.30) with the
inputs encapsulated as shown in 7.23.6."
To avoid confusion, fix the warning messsage to mention switching to PIO and
not "unqueued" and rename the macro ATA_HORKAGE_NO_NCQ_LOG to
ATA_HORKAGE_NO_DMA_LOG.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- Christoph added support for TCG OPAL self encrypting disks
- Minwoo added support for ATA PASS-THROUGH(32)
- Linus Walleij removed spurious drvdata assignments in some drivers
- Support for a few new device and other fixes
* 'for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (33 commits)
sd: add support for TCG OPAL self encrypting disks
libata: fix build warning from unused goto label
libata: Support for an ATA PASS-THROUGH(32) command.
ahci: Add Device ID for ASMedia 1061R and 1062R
sata_via: Enable optional hotplug on VT6420
ata: ahci_brcm: Avoid writing to read-only registers
libata: Add the AHCI_HFLAG_NO_WRITE_TO_RO flag
libata: Add the AHCI_HFLAG_YES_ALPM flag
ata: ftide010: fix resource printing
libata: make the function name in comment match the actual function
ata: sata_rcar: make of_device_ids const.
ata: pata_octeon_cf: make of_device_ids const.
libata: Convert bare printks to pr_cont
libahci: wrong comments in ahci_do_softreset()
ata: declare ata_port_info structures as const
ata: Add driver for Faraday Technology FTIDE010
ata: Add DT bindings for the Gemini SATA bridge
ata: Add DT bindings for Faraday Technology FTIDE010
libata: implement SECURITY PROTOCOL IN/OUT
libata: factor out a ata_identify_page_supported helper
...
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates.
-----BEGIN PGP SIGNATURE-----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=cVjZ
-----END PGP SIGNATURE-----
Merge tag 'docs-4.13' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There has been a fair amount of activity in the docs tree this time
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates"
* tag 'docs-4.13' of git://git.lwn.net/linux: (90 commits)
scripts/kernel-doc: handle DECLARE_HASHTABLE
Documentation: atomic_ops.txt is core-api/atomic_ops.rst
Docs: clean up some DocBook loose ends
Make the main documentation title less Geocities
Docs: Use kernel-figure in vidioc-g-selection.rst
Docs: fix table problems in ras.rst
Docs: Fix breakage with Sphinx 1.5 and upper
Docs: Include the Latex "ifthen" package
doc/kokr/howto: Only send regression fixes after -rc1
docs-rst: fix broken links to dynamic-debug-howto in kernel-parameters
doc: Document suitability of IBM Verse for kernel development
Doc: fix a markup error in coding-style.rst
docs: driver-api: i2c: remove some outdated information
Documentation: DMA API: fix a typo in a function name
Docs: Insert missing space to separate link from text
doc/ko_KR/memory-barriers: Update control-dependencies example
Documentation, kbuild: fix typo "minimun" -> "minimum"
docs: Fix some formatting issues in request-key.rst
doc: ReSTify keys-trusted-encrypted.txt
doc: ReSTify keys-request-key.txt
...
SAT-4(SCSI/ATA Translation) supports for an ata pass-thru(32).
This patch will allow to translate an ata pass-thru(32) SCSI cmd
to an ATA cmd.
Signed-off-by: Minwoo Im <dn3108@gmail.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
tj: Updated line continuation style for consistency as pointed out by
Sergei.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It is core functionality, and only one of the users is in the EH code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_parse_force_one() was incorrectly comparing @p to @endp when it
should have been comparing @id. The only consequence is that it may
end up using an invalid port number in "libata.force" module param
instead of rejecting it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Petru-Florin Mihancea <petrum@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195785
The libata documentation is now using ReST. Update references
to it to point to the new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The libata documentation is now using ReST. Update references
to it to point to the new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes the following sparse warning:
drivers/ata/libata-core.c:4913:6: warning: symbol 'ata_sg_clean' was not
declared. Should it be static?
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Use setup_deferrable_timer() instead of init_timer_deferrable() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For an ATA device supporting the sense data reporting feature set, a
failed command will trigger the execution of ata_eh_request_sense if
the result task file of the failed command has the ATA_SENSE bit set
(sense data available bit). ata_eh_request_sense executes the REQUEST
SENSE DATA EXT command to retrieve the sense data of the failed
command. On success of REQUEST SENSE DATA EXT, the ATA_SENSE bit will
NOT be set (the command succeeded) but ata_eh_request_sense
nevertheless tests the availability of sense data by testing that bit
presence in the result tf of the REQUEST SENSE DATA EXT command. This
leads us to falsely assume that request sense data failed and to the
warning message:
atax.xx: request sense failed stat 50 emask 0
Upon success of REQUEST SENSE DATA EXT, set the ATA_SENSE bit in the
result task file command so that sense data can be returned by
ata_eh_request_sense.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Marko reports that CX1-JB512-HP shows the same timeout issues as
CX1-JB256-HP. Let's apply MAX_SEC_128 to all devices in the series.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marko Koski-Vähälä <marko@koski-vahala.com>
Cc: stable@vger.kernel.org # v3.19+
If NO_DMA=y:
ERROR: "bad_dma_ops" [drivers/ata/libata.ko] undefined!
To fix this, protect the DMA code by #ifdef CONFIG_HAS_DMA, and provide
dummies of ata_sg_clean() and ata_sg_setup() for the !CONFIG_HAS_DMA
case.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 70e6ad0c6d ("[PATCH] libata: prepare ata_sg_clean() for
invocation from EH") made ata_sg_clean() global, but no user outside
libata-core.c has ever materialized.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull another libata patch from Tejun Heo:
"One more patch from Adam added.
It makes libata skip probing for NCQ prio unless the feature is
explicitly requested by the user. This is necessary because some
controllers lock up after the optional feature is probed"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: avoid probing NCQ Prio Support if not explicitly requested
Previously, when the ata device was being initialized we were
probing for NCQ prio support by checking the identify information
and also checking the log page that holds information about ncq prio
support.
This caused an error on an Intel HBA so the code is now updated to
only probe for NCQ prio support when the sysfs variable controlling
NCQ prio support is enabled.
tj: Update formatting, switch to spin_[un]lock_irq() and update
locking a bit, use REVALIDATE instead of RESET, and return -EIO
instead of -EINVAL on config failure.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- Adam added opt-in ATA command priority support.
- There are machines which hide multiple nvme devices behind an ahci
BAR. Dan Williams proposed a solution to force-switch the mode but
deemed too hackishd. People are gonna discuss the proper way to
handle the situation in nvme standard meetings. For now, detect and
warn about the situation.
- Low level driver specific changes.
Christoph Hellwig pipes in about the hidden nvme warning:
"I wish that was the case. We've pretty much agreed that we'll want to
implement it as a virtual PCIe root bridge, similar to Intels other
'innovation' VMD that we work around that way.
But Intel management has apparently decided that they don't want to
spend more cycles on this now that Lenovo has an optional BIOS that
doesn't force this broken mode anymore, and no one outside of Intel
has enough information to implement something like this.
So for now I guess this warning is it, until Intel reconsideres and
spends resources on fixing up the damage their Chipset people caused"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: warn about remapped NVMe devices
ahci-remap.h: add ahci remapping definitions
nvme: move NVMe class code to pci_ids.h
pata: imx: support controller modes up to PIO4
pata: imx: add support of setting timings for PIO modes
pata: imx: set controller PIO mode with .set_piomode callback
pata: imx: sort headers out
ata: set ncq_prio_enabled iff device has support
ata: ATA Command Priority Disabled By Default
ata: Enabling ATA Command Priorities
block: Add iocontext priority to request
ahci: qoriq: added ls1046a platform support
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We previously had a check to see if the device has support for
prioritized ncq commands and a check to see if a device flag
is set, through a sysfs variable, in order to send a prioritized
command.
This patch only allows the sysfs variable to be set if the device
supports prioritized commands enabling one check in ata_build_rw_tf
in order to determine whether or not to send a prioritized command.
This patch depends on ata: ATA Command Priority Disabled By Default
tj: Minor subject and formatting updates.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a sysfs entry to turn on priority information being passed
to a ATA device. By default this feature is turned off.
This patch depends on ata: Enabling ATA Command Priorities
tj: Renamed ncq_prio_on to ncq_prio_enable and removed trivial
ata_ncq_prio_on() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch checks to see if an ATA device supports NCQ command priorities.
If so and the user has specified an iocontext that indicates
IO_PRIO_CLASS_RT then we build a tf with a high priority command.
This is done to improve the tail latency of commands that are high
priority by passing priority to the device.
tj: Removed trivial ata_ncq_prio_enabled() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=8lmX
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger"
* tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: is31fl32xx: define complete i2c_device_id table
leds: is31fl32xx: fix typo in id and match table names
leds: LED driver for TI LP3952 6-Channel Color LED
leds: leds-gpio: Set of_node for created LED devices
leds: triggers: return error if invalid trigger name is provided via sysfs
leds: Only descend into leds directory when CONFIG_NEW_LEDS is set
leds: Add no-op gpio_led_register_device when LED subsystem is disabled
unicore32: use the new LED disk activity trigger
parisc: use the new LED disk activity trigger
mips: use the new LED disk activity trigger
arm: use the new LED disk activity trigger
powerpc: use the new LED disk activity trigger
leds: documentation: 'ide-disk' to 'disk-activity'
leds: convert IDE trigger to common disk trigger
leds: pca9532: Add device tree support
MAINTAINERS: Add file patterns for led device tree bindings
Pull libata updates from Tejun Heo:
"libata saw quite a bit of activities in this cycle:
- SMR drive support still being worked on
- bug fixes and improvements to misc SCSI command emulation
- some low level driver updates"
* 'for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (39 commits)
libata-scsi: better style in ata_msense_*()
AHCI: Clear GHC.IS to prevent unexpectly asserting INTx
ata: sata_dwc_460ex: remove redundant dev_err call
ata: define ATA_PROT_* in terms of ATA_PROT_FLAG_*
libata: remove ATA_PROT_FLAG_DATA
libata: remove ata_is_nodata
ata: make lba_{28,48}_ok() use ATA_MAX_SECTORS{,_LBA48}
libata-scsi: minor cleanup for ata_scsi_zbc_out_xlat
libata-scsi: Fix ZBC management out command translation
libata-scsi: Fix translation of REPORT ZONES command
ata: Handle ATA NCQ NO-DATA commands correctly
libata-eh: decode all taskfile protocols
ata: fixup ATA_PROT_NODATA
libsas: use ata_is_ncq() and ata_has_dma() accessors
libata: use ata_is_ncq() accessors
libata: return boolean values from ata_is_*
libata-scsi: avoid repeated calculation of number of TRIM ranges
libata-scsi: reject WRITE SAME (16) with n_block that exceeds limit
libata-scsi: rename ata_msense_ctl_mode() to ata_msense_control()
libata-scsi: fix D_SENSE bit relection in control mode page
...
The taskfile protocol is a numeric value, and can not be ORed. Currently
this is harmless as the protocol is always zeroed before, but if it ever
has a non-zero value the ORing would create incorrect results.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[hch: updated patch description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use accessor functions instead of the raw value.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Without this fix, the DRA bit of the caching mode page would not
be updated when the read look-ahead feature is toggled (e.g. with
`smartctl --set`), but will only be until, for example, the write
cache feature is touched.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch converts the IDE specific LED trigger to a generic disk
activity LED trigger. The libata core is now a trigger source just
like before the IDE disk driver. It's merely a replacement of the
string ide by disk.
The patch is taken from http://dev.gentoo.org/~josejx/ata.patch and is
widely used by any ibook/powerbook owners with great satisfaction.
Likewise, it is very often used successfully on different ARM platforms.
Unlike the original patch, the existing 'ide-disk' trigger is still
available for backward compatibility. That reduce the amount of patches
in affected device trees out of the mainline kernel. For further
development, the new name 'disk-activity' should be used.
Cc: Joseph Jezak <josejx@gentoo.org>
Cc: Jörg Sommer <joerg@alea.gnuu.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Pull libata ZAC support from Tejun Heo:
"This contains Zone ATA Command support for Shingled Magnetic Recording
devices.
In addition to sending the new commands down to the device, as ZAC
commands depend on getting a lot of responses from the device, piping
up responses is beefed up too. However, it doesn't involve changes to
libata core mechanism or its interaction with upper layers, so I'm not
expecting too many fallouts.
Kudos to Hannes for driving SMR support"
* 'for-4.7-zac' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (28 commits)
libata: support host-aware and host-managed ZAC devices
libata: support device-managed ZAC devices
libata: NCQ encapsulation for ZAC MANAGEMENT OUT
libata: Implement ZBC OUT translation
libata: implement ZBC IN translation
libata: fixup ZAC device disabling
libata-scsi: Generate sense code for disabled devices
libata-trace: decode subcommands
libata: Check log page directory before accessing pages
libata: Add command definitions for NCQ Encapsulation for READ LOG DMA EXT
libata: Separate out ata_dev_config_ncq_send_recv()
libata/libsas: Define ATA_CMD_NCQ_NON_DATA
libsas: enable FPDMA SEND/RECEIVE
libata: do not attempt to retrieve sense code twice
libata-scsi: Set information sense field for invalid parameter
libata-scsi: set bit pointer for sense code information
libata-scsi: Set field pointer in sense code
scsi: add scsi_set_sense_field_pointer()
libata: Implement control mode page to select sense format
libata-scsi: generate correct ATA pass-through sense
...
Byte 69 bits 0:1 in the IDENTIFY DEVICE data indicate a
host-aware ZAC device.
Host-managed ZAC devices have their own individual signature,
and to not set the bits in the IDENTIFY DEVICE data.
And whenever we detect a ZAC-compatible device we should
be displaying the zoned block characteristics VPD page.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add NCQ encapsulation for ZAC MANAGEMENT OUT and evaluate
NCQ Non-Data log pages to figure out if NCQ encapsulation
is supported.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When reading the NCQ Send/Recv log it might actually not
supported, thereby causing irritating messages
'READ LOG DMA EXT failed'.
Instead we should be reading the log directory first to
figure out if the log is actually supported before trying
to access it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
