We only need this code to support scsi, ide, cciss and virtio. And at
least for virtio it's a deprecated feature to start with.
This should shrink the kernel size for embedded device that only use,
say eMMC a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
And require all drivers that want to support BLOCK_PC to allocate it
as the first thing of their private data. To support this the legacy
IDE and BSG code is switched to set cmd_size on their queues to let
the block layer allocate the additional space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Port and ACL information must be configured before an initiator
logs in. Make it possible to configure this information before
a subnet prefix has been assigned to a port by not only accepting
GIDs as target port and initiator port names but by also accepting
port GUIDs.
Add a 'priv' member to struct se_wwn to allow target drivers to
associate their own data with struct se_wwn.
Reported-by: Doug Ledford <dledford@redhat.com>
References: http://www.spinics.net/lists/linux-rdma/msg39505.html
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since we need to change the implementation, stop exposing internals.
Provide kref_read() to read the current reference count; typically
used for debug messages.
Kills two anti-patterns:
atomic_read(&kref->refcount)
kref->refcount.counter
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
SPC4r37 6.4.1 EXTENDED COPY(LID4) states (also applying to LID1 reqs):
A parameter list length of zero specifies that the copy manager shall
not transfer any data or alter any internal state, and this shall not
be considered an error.
This behaviour can be tested using the libiscsi ExtendedCopy.ParamHdr
test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Check for XCOPY header, CSCD descriptor and segment descriptor list
truncation, and respond accordingly.
SPC4r37 6.4.1 EXTENDED COPY(LID4) states (also applying to LID1 reqs):
If the parameter list length causes truncation of the parameter list,
then the copy manager shall transfer no data and shall terminate the
EXTENDED COPY command with CHECK CONDITION status, with the sense key
set to ILLEGAL REQUEST, and the additional sense code set to PARAMETER
LIST LENGTH ERROR.
This behaviour can be tested using the libiscsi ExtendedCopy.ParamHdr
test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
The XCOPY specification in SPC4r37 states that the XCOPY source and
destination device(s) should be derived from the copy source and copy
destination (CSCD) descriptor IDs in the XCOPY segment descriptor.
The CSCD IDs are generally (for block -> block copies), indexes into
the corresponding CSCD descriptor list, e.g.
=================================
EXTENDED COPY Header
=================================
CSCD Descriptor List
- entry 0
+ LU ID <--------------<------------------\
- entry 1 |
+ LU ID <______________<_____________ |
================================= | |
Segment Descriptor List | |
- segment 0 | |
+ src CSCD ID = 0 --------->---------+----/
+ dest CSCD ID = 1 ___________>______|
+ len
+ src lba
+ dest lba
=================================
Currently LIO completely ignores the src and dest CSCD IDs in the
Segment Descriptor List, and instead assumes that the first entry in the
CSCD list corresponds to the source, and the second to the destination.
This commit removes this assumption, by ensuring that the Segment
Descriptor List is parsed prior to processing the CSCD Descriptor List.
CSCD Descriptor List processing is modified to compare the current list
index with the previously obtained src and dest CSCD IDs.
Additionally, XCOPY requests where the src and dest CSCD IDs refer to
the CSCD Descriptor List entry can now be successfully processed.
Fixes: cbf031f ("target: Add support for EXTENDED_COPY copy offload")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=191381
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Ensure that the segment descriptor CSCD descriptor ID values correspond
to CSCD descriptor entries located in the XCOPY command parameter list.
SPC4r37 6.4.6.1 Table 150 specifies this range as 0000h to 07FFh, where
the CSCD descriptor location in the parameter list can be located via:
16 + (id * 32)
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: inserted "; " in the format string of an error message
and also moved a "||" operator from the start of a line to the end
of the previous line ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
target_xcopy_locate_se_dev_e4() is used to locate an se_dev, based on
the WWN provided with the XCOPY request. Remove a couple of unneeded
arguments, and rely on the caller for the src/dst test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Use UNSUPPORTED TARGET DESCRIPTOR TYPE CODE and UNSUPPORTED SEGMENT
DESCRIPTOR TYPE CODE additional sense codes if a descriptor type in an
XCOPY request is not supported, as specified in spc4r37 6.4.5 and 6.4.6.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
spc4r37 6.4.3.5 states:
If the combined length of the CSCD descriptors and segment descriptors
exceeds the allowed value, then the copy manager shall terminate the
command with CHECK CONDITION status, with the sense key set to ILLEGAL
REQUEST, and the additional sense code set to PARAMETER LIST LENGTH
ERROR.
This functionality can be tested using the libiscsi
ExtendedCopy.DescrLimits test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Check the length of the XCOPY request segment descriptor list against
the value advertised via the MAXIMUM SEGMENT DESCRIPTOR COUNT field in
the RECEIVE COPY OPERATING PARAMETERS response.
spc4r37 6.4.3.5 states:
If the number of segment descriptors exceeds the allowed number, the
copy manager shall terminate the command with CHECK CONDITION status,
with the sense key set to ILLEGAL REQUEST, and the additional sense
code set to TOO MANY SEGMENT DESCRIPTORS.
This functionality is testable using the libiscsi
ExtendedCopy.DescrLimits test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
spc4r37 6.4.3.4 states:
If the number of CSCD descriptors exceeds the allowed number, the copy
manager shall terminate the command with CHECK CONDITION status, with
the sense key set to ILLEGAL REQUEST, and the additional sense code
set to TOO MANY TARGET DESCRIPTORS.
LIO currently responds with INVALID FIELD IN PARAMETER LIST, which sees
it fail the libiscsi ExtendedCopy.DescrLimits test.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
As defined in http://www.t10.org/lists/asc-num.htm. To be used during
validation of XCOPY target and segment descriptor lists.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Pull scsi target cleanups from Bart Van Assche:
"The changes here are:
- a few small bug fixes for the iSCSI and user space target drivers.
- minimize the target build time by about 30% by rearranging #include
directives
- fix the second argument passed to percpu_ida_alloc()
- reduce the number of false positive warnings reported by sparse
These patches pass Wu Fengguang's build bot tests and also the
linux-next tests"
* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
iscsi-target: Return error if unable to add network portal
target: Fix spelling mistake and unwrap multi-line text
target/iscsi: Fix double free in lio_target_tiqn_addtpg()
target/user: Fix use-after-free of tcmu_cmds if they are expired
target: Minimize #include directives
target/user: Add an #include directive
cxgbit: Add an #include directive
ibmvscsi_tgt: Add two #include directives
sbp-target: Add an #include directive
qla2xxx: Add an #include directive
configfs: Minimize #include directives
usb: gadget: Fix second argument of percpu_ida_alloc()
sbp-target: Fix second argument of percpu_ida_alloc()
target/user: Fix a data type in tcmu_queue_cmd()
target: Use NULL instead of 0 to represent a pointer
Pull vfs updates from Al Viro:
- more ->d_init() stuff (work.dcache)
- pathname resolution cleanups (work.namei)
- a few missing iov_iter primitives - copy_from_iter_full() and
friends. Either copy the full requested amount, advance the iterator
and return true, or fail, return false and do _not_ advance the
iterator. Quite a few open-coded callers converted (and became more
readable and harder to fuck up that way) (work.iov_iter)
- several assorted patches, the big one being logfs removal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
logfs: remove from tree
vfs: fix put_compat_statfs64() does not handle errors
namei: fold should_follow_link() with the step into not-followed link
namei: pass both WALK_GET and WALK_MORE to should_follow_link()
namei: invert WALK_PUT logics
namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link()
namei: saner calling conventions for mountpoint_last()
namei.c: get rid of user_path_parent()
switch getfrag callbacks to ..._full() primitives
make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success
[iov_iter] new primitives - copy_from_iter_full() and friends
don't open-code file_inode()
ceph: switch to use of ->d_init()
ceph: unify dentry_operations instances
lustre: switch to use of ->d_init()
If iscsit_tpg_add_network_portal() fails then
return error code instead of 0 to user space.
If iscsi-target returns 0 then user space keeps
on retrying same command infinitely, targetcli or
echo hangs till command completes with non zero
return value. In some cases it is possible that
add network portal command never completes with
success even after retrying multiple times,
for example - cxgbit_setup_np() always returns
-EINVAL if portal IP does not belong to Chelsio
adapter interface.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
[ bvanassche: Added "Fixes:" and "Cc: stable" tags ]
Fixes: commit d4b3fa4b08 ("iscsi-target: Make iscsi_tpg_np driver show/store use generic code")
Cc: <stable@vger.kernel.org>
Trivial fix to spelling mistake "Obselete" to "Obsolete"
in error message and also turn multi-line text into one
line.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
This iscsit_tpg_add_portal_group() function is only called from
lio_target_tiqn_addtpg(). Both functions free the "tpg" pointer on
error so it's a double free bug. The memory is allocated in the caller
so it should be freed in the caller and not here.
Fixes: e48354ce07 ("iscsi-target: Add iSCSI fabric support for target v4.1")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Disseldorp <ddiss@suse.de>
[ bvanassche: Added "Fix" at start of patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Don't free the cmd in tcmu_check_expired_cmd, it's still referenced by
an entry in our cmd_id->cmd idr. If userspace ever resumes processing,
tcmu_handle_completions() will use the now-invalid cmd pointer.
Instead, don't free cmd. It will be freed by tcmu_handle_completion() if
userspace ever recovers, or tcmu_free_device if not.
Cc: stable@vger.kernel.org
Reported-by: Bryant G Ly <bgly@us.ibm.com>
Tested-by: Bryant G Ly <bgly@us.ibm.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
from the ->drop_link method.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nOOH
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-4.10' of git://git.infradead.org/users/hch/configfs
Pull configfs update from Christoph Hellwig:
"Just one simple change from Andrzej to drop the pointless return value
from the ->drop_link method"
* tag 'configfs-for-4.10' of git://git.infradead.org/users/hch/configfs:
fs: configfs: don't return anything from drop_link
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
Remove superfluous #include directives from the include/target/*.h
files. Add missing #include directives to other *.h and *.c files.
Use forward declarations for structures where possible. This
change reduces the build time for make M=drivers/target on my
laptop from 27.1s to 18.7s or by about 30%.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Since this driver uses kmap_atomic(), include the highmem header file.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Andy Grover <agrover@redhat.com>
Include header <net/tcp.h> to ensure that the definition of before()
is available.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Varun Prakash <varun@chelsio.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
usleep_range() is called from sbp_target.c. Hence include header
file <linux/delay.h>.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Chris Boot <bootc@bootc.net>
Pass a task state as second argument to percpu_ida_alloc().
Fixes: commit 5a3ee221b5 ("sbp-target: Conversion to percpu_ida tag pre-allocation")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Chris Boot <bootc@bootc.net>
This patch avoids that sparse reports the following error messages:
drivers/target/target_core_user.c:547:13: warning: incorrect type in assignment (different base types)
drivers/target/target_core_user.c:547:13: expected int [signed] ret
drivers/target/target_core_user.c:547:13: got restricted sense_reason_t
drivers/target/target_core_user.c:548:20: warning: restricted sense_reason_t degrades to integer
drivers/target/target_core_user.c:557:16: warning: incorrect type in return expression (different base types)
drivers/target/target_core_user.c:557:16: expected restricted sense_reason_t
drivers/target/target_core_user.c:557:16: got int [signed] ret
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Documentation/filesystems/configfs/configfs.txt says:
"When unlink(2) is called on the symbolic link, the source item is
notified via the ->drop_link() method. Like the ->drop_item() method,
this is a void function and cannot return failure."
The ->drop_item() is indeed a void function, the ->drop_link() is
actually not. This, together with the fact that the value of ->drop_link()
is silently ignored suggests, that it is the ->drop_link() return
type that should be corrected and changed to void.
This patch changes drop_link() signature and all its users.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[hch: reverted reformatting of some code]
Signed-off-by: Christoph Hellwig <hch@lst.de>
When the bio is full, bio_add_pc_page() will return zero,
so use this information tell when the bio is full.
Also replace access to .bi_vcnt for pr_debug() with bio_segments().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allocate resources dynamically for Upper layer driver's (ULD) like
cxgbit, iw_cxgb4, cxgb4i and chcr. The resources allocated include Tx
queues which are allocated when ULD register with cxgb4 driver and freed
while un-registering. The Tx queues which are shared by ULD shall be
allocated by first registering driver and un-allocated by last
unregistering driver.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->seq_release callback only ever had one implementation,
so call the function directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->seq_assign callback only ever had one implementation,
so call the function directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->seq_set_resp callback only ever had one implementation,
so call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->seq_start_next callback only ever had one implementation,
so call the function directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->exch_done callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ->seq_send callback only ever had one implementation,
so we can as well call it directly and drop the callback.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the WRITE_* and READ_SYNC wrappers, and just use the flags
directly. Where applicable this also drops usage of the
bio_set_op_attrs wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now genl_register_family() is the only thing (other than the
users themselves, perhaps, but I didn't find any doing that)
writing to the family struct.
In all families that I found, genl_register_family() is only
called from __init functions (some indirectly, in which case
I've add __init annotations to clarifly things), so all can
actually be marked __ro_after_init.
This protects the data structure from accidental corruption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The libfc stack assigns exchange IDs based on the CPU the request
was received on, so we need to send the responses via the same CPU.
Otherwise the send logic gets confuses and responses will be delayed,
causing exchange timeouts on the initiator side.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Update the debug statements to match those from libfc.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Not every failure is due to out-of-memory; the ACLs might not be
set, too. So return a detailed error code in ft_sess_create()
instead of just a NULL pointer.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When allocating a new command we should add the pointer to the
debug statements; that allows us to match this with other debug
statements for handling data.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target_sess_cmd_list_waiting() might hit on a condition where
the kref for the command is already 0, but the destructor has
not been called yet (or is stuck in waiting for a spin lock).
Rather than leaving the command on the list we should explicitly
remove it to avoid race issues later on.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This reverts commit c1ccbfe031.
Reverting this patch, as it incorrectly assumes the additional length
for INQUIRY in target_complete_cmd_with_length() is SCSI allocation
length, which breaks existing user-space code when SCSI allocation
length is smaller than additional length.
root@scsi-mq:~# sg_inq --len=4 -vvvv /dev/sdb
found bsg_major=253
open /dev/sdb with flags=0x800
inquiry cdb: 12 00 00 00 04 00
duration=0 ms
inquiry: pass-through requested 4 bytes (data-in) but got -28 bytes
inquiry: pass-through can't get negative bytes, say it got none
inquiry: got too few bytes (0)
INQUIRY resid (32) should never exceed requested len=4
inquiry: failed requesting 4 byte response: Malformed response to
SCSI command [resid=32]
AFAICT the original change was not to address a specific host issue,
so go ahead and revert to original logic for now.
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sumit Rai <sumitrai96@gmail.com>
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where a local EXTENDED_COPY WRITE or READ
backend I/O request would always return SAM_STAT_CHECK_CONDITION,
even if underlying xcopy_pt_cmd->se_cmd generated a different
SCSI status code.
ESX host environments expect to hit SAM_STAT_RESERVATION_CONFLICT
for certain scenarios, and SAM_STAT_CHECK_CONDITION results in
non-retriable status for these cases.
Tested on v4.1.y with ESX v5.5u2+ with local IBLOCK backend copy.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Cc: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Dinesh Israni <ddi@datera.io>
Signed-off-by: Dinesh Israni <ddi@datera.io>
Cc: Dinesh Israni <ddi@datera.io>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where EXTENDED_COPY across multiple LUNs
results in a CHECK_CONDITION when the source + destination are not
located on the same physical node.
ESX Host environments expect sense COPY_ABORTED w/ COPY TARGET DEVICE
NOT REACHABLE to be returned when this occurs, in order to signal
fallback to local copy method.
As described in section 6.3.3 of spc4r22:
"If it is not possible to complete processing of a segment because the
copy manager is unable to establish communications with a copy target
device, because the copy target device does not respond to INQUIRY,
or because the data returned in response to INQUIRY indicates
an unsupported logical unit, then the EXTENDED COPY command shall be
terminated with CHECK CONDITION status, with the sense key set to
COPY ABORTED, and the additional sense code set to COPY TARGET DEVICE
NOT REACHABLE."
Tested on v4.1.y with ESX v5.5u2+ with BlockCopy across multiple nodes.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Cc: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Dinesh Israni <ddi@datera.io>
Signed-off-by: Dinesh Israni <ddi@datera.io>
Cc: Dinesh Israni <ddi@datera.io>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a regression in >= v4.1.y code where the original
SCF_ACK_KREF assignment in target_get_sess_cmd() was dropped upstream
in commit 054922bb, but the series for addressing TMR ABORT_TASK +
LUN_RESET with fabric session reinstatement in commit febe562c20 still
depends on this code in transport_cmd_finish_abort().
The regression manifests itself as a se_cmd->cmd_kref +1 leak, where
ABORT_TASK + LUN_RESET can hang indefinately for a specific I_T session
for drivers using SCF_ACK_KREF, resulting in hung kthreads.
This patch has been verified with v4.1.y code.
Reported-by: Vaibhav Tandon <vst@datera.io>
Tested-by: Vaibhav Tandon <vst@datera.io>
Cc: Vaibhav Tandon <vst@datera.io>
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If iscsi-target receives NOP OUT with ITT and TTT
set to 0xffffffff it allocates iscsi_cmd but
does not free the cmd, so free iscsi_cmd in this case.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Trivial fix to spelling mistakes in pr_debug message and comments
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We no longer use a ringbuffer for the data area, so this might cause
confusion. Just call it the data area.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Userspace should be implementing VPD B0 (Block Limits) to inform the
initiator of max data size, but just in case we do get a too-large request,
do what the spec says and return INVALID_CDB_FIELD.
Make sure to unlock udev->cmdr_lock before returning.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of using -ERROR-style returns, use sense_reason_t. This lets us
remove tcmu_pass_op(), and return more correct sense values.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Allocate resources dynamically to cxgb4's Upper layer driver's(ULD) like
cxgbit, iw_cxgb4 and cxgb4i. Allocate resources when they register with
cxgb4 driver and free them while unregistering. All the queues and the
interrupts for them will be allocated during ULD probe only and freed
during remove.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_rx_data_ack() to remove duplicate
code to form CPL_RX_DATA_ACK hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_abort_rpl() to remove duplicate
code to form CPL_ABORT_RPL hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_abort_req() to remove duplicate code
to form CPL_ABORT_REQ hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_close_con_req() to remove duplicate
code to form CPL_CLOSE_CON_REQ hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_tid_release() to remove duplicate code
to form CPL_TID_RELEASE hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_compute_wscale() in libcxgb_cm.h to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_best_mtu() in libcxgb_cm.h to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_is_neg_adv() in libcxgb_cm.h to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_find_route6() in libcxgb_cm.c to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_find_route() in libcxgb_cm.c to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_get_4tuple() in libcxgb_cm.c to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original commit missed this function, it needs to mark it a
write flush.
Cc: Mike Christie <mchristi@redhat.com>
Fixes: e742fc32fc ("target: use bio op accessors")
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull SCSI target updates from Nicholas Bellinger:
"The most notable item is IBM virtual SCSI target driver, that was
originally ported to target-core back in 2010 by Tomo-san, and has
been brought forward to v4.x code by Bryant Ly, Michael Cyr and co
over the last months.
Also included are two ORDERED task related bug-fixes Bryant + Michael
found along the way using ibmvscsis with AIX guests, plus a few
miscellaneous target-core + iscsi-target bug-fixes with associated
stable tags"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: fix spelling mistake: "limitiation" -> "limitation"
target: Fix residual overflow handling in target_complete_cmd_with_length
tcm_fc: set and unset FCP_SPPF_TARG_FCN
iscsi-target: Fix panic when adding second TCP connection to iSCSI session
ibmvscsis: Initial commit of IBM VSCSI Tgt Driver
target: Fix ordered task CHECK_CONDITION early exception handling
target: Fix ordered task target_setup_cmd_from_cdb exception hang
target: Fix max_unmap_lba_count calc overflow
target: Fix race between iscsi-target connection shutdown + ABORT_TASK
target: Fix missing complete during ABORT_TASK + CMD_T_FABRIC_STOP
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
Export cxgbi_ppm_release() to release
ppod manager and cxgbi_tagmask_set() to
set tag mask, they are used by cxgb3i, cxgb4i
and cxgbit.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add common library module(libcxgb.ko) for
Chelsio drivers to remove duplicate code.
Code for iSCSI DDP Page Pod Manager is moved
from cxgb4.ko to libcxgb.ko. Earlier only cxgbit.ko
was using this code, now cxgb3i and cxgb4i will
also use common Page Pod manager code.
In future this module will have common connection
management and hardware specific code that can be
shared by multiple Chelsio drivers.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes residual overflow handling to correctly set the
residual_count using SPDTL, instead of SCSI Allocation Length.
Allocation Length is the maximum value of the SPDTL and not substitute
for it, hence it shouldn’t be used to calculate ResidualCount except for
cases where SPDTL > Allocation Length and Data is truncated (in that
case both Alloc Len and SPDTL are same). (SPC 5r01 Section 4.2.5.6).
Thanks to Ajay Nair in assisting with this patch.
Signed-off-by: Sumit Rai <sumitrai96@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Using blk_rq_append_bio allows to append the bios to the request
directly instead of having to build up a list first, and also
allows to have a single code path for requests with or without
data attached to them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When registering and unregistering as an target port we should
be setting the FC-4 service params correctly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In MC/S scenario, the conn->sess has been set NULL in
iscsi_login_non_zero_tsih_s1 when the second connection comes here,
then kernel panic.
The conn->sess will be assigned in iscsi_login_non_zero_tsih_s2. So
we should check whether it's NULL before calling.
Signed-off-by: Feng Li <lifeng1519@gmail.com>
Tested-by: Sumit Rai <sumit.rai@calsoftinc.com>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If a Simple command is sent with a failure, target_setup_cmd_from_cdb
returns with TCM_UNSUPPORTED_SCSI_OPCODE or TCM_INVALID_CDB_FIELD.
So in the cases where target_setup_cmd_from_cdb returns an error, we
never get far enough to call target_execute_cmd to increment simple_cmds.
Since simple_cmds isn't incremented, the result of the failure from
target_setup_cmd_from_cdb causes transport_generic_request_failure to
decrement simple_cmds, due to call to transport_complete_task_attr.
With this dev->simple_cmds or dev->dev_ordered_sync is now -1, not 0.
So when a subsequent command with an Ordered Task is sent, it causes
a hang, since dev->simple_cmds is at -1.
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If a command with a Simple task attribute is failed due to a Unit
Attention, then a subsequent command with an Ordered task attribute
will hang forever. The reason for this is that the Unit Attention
status is checked for in target_setup_cmd_from_cdb, before the call
to target_execute_cmd, which calls target_handle_task_attr, which
in turn increments dev->simple_cmds.
However, transport_generic_request_failure still calls
transport_complete_task_attr, which will decrement dev->simple_cmds.
In this case, simple_cmds is now -1. So when a command with the
Ordered task attribute is sent, target_handle_task_attr sees that
dev->simple_cmds is not 0, so it decides it can't execute the
command until all the (nonexistent) Simple commands have completed.
Reported-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Reported-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
max_discard_sectors only 32bits, and some non scsi backend
devices will set this to the max 0xffffffff, so we can end up
overflowing during the max_unmap_lba_count calculation.
This fixes a regression caused by my patch:
commit 8a9ebe717a
Author: Mike Christie <mchristi@redhat.com>
Date: Mon Jan 18 14:09:27 2016 -0600
target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors
which can result in extra discards being sent to due the overflow
causing max_unmap_lba_count to be smaller than what the backing
device can actually support.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a race in iscsit_release_commands_from_conn() ->
iscsit_free_cmd() -> transport_generic_free_cmd() + wait_for_tasks=1,
where CMD_T_FABRIC_STOP could end up being set after the final
kref_put() is called from core_tmr_abort_task() context.
This results in transport_generic_free_cmd() blocking indefinately
on se_cmd->cmd_wait_comp, because the target_release_cmd_kref()
check for CMD_T_FABRIC_STOP returns false.
To address this bug, make iscsit_release_commands_from_conn()
do list_splice and set CMD_T_FABRIC_STOP early while holding
iscsi_conn->cmd_lock. Also make iscsit_aborted_task() only
remove iscsi_cmd_t if CMD_T_FABRIC_STOP has not already been
set.
Finally in target_release_cmd_kref(), only honor fabric_stop
if CMD_T_ABORTED has been set.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.14+
Tested-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
During transport_generic_free_cmd() with a concurrent TMR
ABORT_TASK and shutdown CMD_T_FABRIC_STOP bit set, the
caller will be blocked on se_cmd->cmd_wait_stop completion
until the final kref_put() -> target_release_cmd_kref()
has been invoked to call complete().
However, when ABORT_TASK is completed with FUNCTION_COMPLETE
in core_tmr_abort_task(), the aborted se_cmd will have already
been removed from se_sess->sess_cmd_list via list_del_init().
This results in target_release_cmd_kref() hitting the
legacy list_empty() == true check, invoking ->release_cmd()
but skipping complete() to wakeup se_cmd->cmd_wait_stop
blocked earlier in transport_generic_free_cmd() code.
To address this bug, it's safe to go ahead and drop the
original list_empty() check so that fabric_stop invokes
the complete() as expected, since list_del_init() can
safely be used on a empty list.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.14+
Tested-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Separate the op from the rq_flag_bits and have the target layer
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the outstanding target pending updates for v4.7-rc1.
The highlights this round include:
- Allow external PR/ALUA metadata path be defined at runtime via top
level configfs attribute (Lee)
- Fix target session shutdown bug for ib_srpt multi-channel (hch)
- Make TFO close_session() and shutdown_session() optional (hch)
- Drop se_sess->sess_kref + convert tcm_qla2xxx to internal kref
(hch)
- Add tcm_qla2xxx endpoint attribute for basic FC jammer (Laurence)
- Refactor iscsi-target RX/TX PDU encode/decode into common code
(Varun)
- Extend iscsit_transport with xmit_pdu, release_cmd, get_rx_pdu,
validate_parameters, and get_r2t_ttt for generic ISO offload
(Varun)
- Initial merge of cxgb iscsi-segment offload target driver (Varun)
The bulk of the changes are Chelsio's new driver, along with a number
of iscsi-target common code improvements made by Varun + Co along the
way"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (29 commits)
iscsi-target: Fix early sk_data_ready LOGIN_FLAGS_READY race
cxgbit: Use type ISCSI_CXGBIT + cxgbit tpg_np attribute
iscsi-target: Convert transport drivers to signal rdma_shutdown
iscsi-target: Make iscsi_tpg_np driver show/store use generic code
tcm_qla2xxx Add SCSI command jammer/discard capability
iscsi-target: graceful disconnect on invalid mapping to iovec
target: need_to_release is always false, remove redundant check and kfree
target: remove sess_kref and ->shutdown_session
iscsi-target: remove usage of ->shutdown_session
tcm_qla2xxx: introduce a private sess_kref
target: make close_session optional
target: make ->shutdown_session optional
target: remove acl_stop
target: consolidate and fix session shutdown
cxgbit: add files for cxgbit.ko
iscsi-target: export symbols
iscsi-target: call complete on conn_logout_comp
iscsi-target: clear tx_thread_active
iscsi-target: add new offload transport type
iscsi-target: use conn_transport->transport_type in text rsp
...
- Updates to the new Intel X722 iWARP driver
- Updates to the hfi1 driver
- Fixes for the iw_cxgb4 driver
- Misc core fixes
- Generic RDMA READ/WRITE API addition
- SRP updates
- Misc ipoib updates
- Minor mlx5 updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+Zv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Primary 4.7 merge window changes
- Updates to the new Intel X722 iWARP driver
- Updates to the hfi1 driver
- Fixes for the iw_cxgb4 driver
- Misc core fixes
- Generic RDMA READ/WRITE API addition
- SRP updates
- Misc ipoib updates
- Minor mlx5 updates"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (148 commits)
IB/mlx5: Fire the CQ completion handler from tasklet
net/mlx5_core: Use tasklet for user-space CQ completion events
IB/core: Do not require CAP_NET_ADMIN for packet sniffing
IB/mlx4: Fix unaligned access in send_reply_to_slave
IB/mlx5: Report Scatter FCS device capability when supported
IB/mlx5: Add Scatter FCS support for Raw Packet QP
IB/core: Add Scatter FCS create flag
IB/core: Add Raw Scatter FCS device capability
IB/core: Add extended device capability flags
i40iw: pass hw_stats by reference rather than by value
i40iw: Remove unnecessary synchronize_irq() before free_irq()
i40iw: constify i40iw_vf_cqp_ops structure
IB/mlx5: Add UARs write-combining and non-cached mapping
IB/mlx5: Allow mapping the free running counter on PROT_EXEC
IB/mlx4: Use list_for_each_entry_safe
IB/SA: Use correct free function
IB/core: Fix a potential array overrun in CMA and SA agent
IB/core: Remove unnecessary check in ibnl_rcv_msg
IB/IWPM: Fix a potential skb leak
RDMA/nes: replace custom print_hex_dump()
...
Pull networking updates from David Miller:
"Highlights:
1) Support SPI based w5100 devices, from Akinobu Mita.
2) Partial Segmentation Offload, from Alexander Duyck.
3) Add GMAC4 support to stmmac driver, from Alexandre TORGUE.
4) Allow cls_flower stats offload, from Amir Vadai.
5) Implement bpf blinding, from Daniel Borkmann.
6) Optimize _ASYNC_ bit twiddling on sockets, unless the socket is
actually using FASYNC these atomics are superfluous. From Eric
Dumazet.
7) Run TCP more preemptibly, also from Eric Dumazet.
8) Support LED blinking, EEPROM dumps, and rxvlan offloading in mlx5e
driver, from Gal Pressman.
9) Allow creating ppp devices via rtnetlink, from Guillaume Nault.
10) Improve BPF usage documentation, from Jesper Dangaard Brouer.
11) Support tunneling offloads in qed, from Manish Chopra.
12) aRFS offloading in mlx5e, from Maor Gottlieb.
13) Add RFS and RPS support to SCTP protocol, from Marcelo Ricardo
Leitner.
14) Add MSG_EOR support to TCP, this allows controlling packet
coalescing on application record boundaries for more accurate
socket timestamp sampling. From Martin KaFai Lau.
15) Fix alignment of 64-bit netlink attributes across the board, from
Nicolas Dichtel.
16) Per-vlan stats in bridging, from Nikolay Aleksandrov.
17) Several conversions of drivers to ethtool ksettings, from Philippe
Reynes.
18) Checksum neutral ILA in ipv6, from Tom Herbert.
19) Factorize all of the various marvell dsa drivers into one, from
Vivien Didelot
20) Add VF support to qed driver, from Yuval Mintz"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1649 commits)
Revert "phy dp83867: Fix compilation with CONFIG_OF_MDIO=m"
Revert "phy dp83867: Make rgmii parameters optional"
r8169: default to 64-bit DMA on recent PCIe chips
phy dp83867: Make rgmii parameters optional
phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
bpf: arm64: remove callee-save registers use for tmp registers
asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
switchdev: pass pointer to fib_info instead of copy
net_sched: close another race condition in tcf_mirred_release()
tipc: fix nametable publication field in nl compat
drivers: net: Don't print unpopulated net_device name
qed: add support for dcbx.
ravb: Add missing free_irq() calls to ravb_close()
qed: Remove a stray tab
net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fec-mpc52xx: use phydev from struct net_device
bpf, doc: fix typo on bpf_asm descriptions
stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fs-enet: use phydev from struct net_device
...
There is a iscsi-target/tcp login race in LOGIN_FLAGS_READY
state assignment that can result in frequent errors during
iscsi discovery:
"iSCSI Login negotiation failed."
To address this bug, move the initial LOGIN_FLAGS_READY
assignment ahead of iscsi_target_do_login() when handling
the initial iscsi_target_start_negotiation() request PDU
during connection login.
As iscsi_target_do_login_rx() work_struct callback is
clearing LOGIN_FLAGS_READ_ACTIVE after subsequent calls
to iscsi_target_do_login(), the early sk_data_ready
ahead of the first iscsi_target_do_login() expects
LOGIN_FLAGS_READY to also be set for the initial
login request PDU.
As reported by Maged, this was first obsered using an
MSFT initiator running across multiple VMWare host
virtual machines with iscsi-target/tcp.
Reported-by: Maged Mokhtar <mmokhtar@binarykinetics.com>
Tested-by: Maged Mokhtar <mmokhtar@binarykinetics.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of having cxgbit use type ISCSI_HW_OFFLOAD + 'hw_offload'
tpg_np attribute, it should be using it's own driver specific
type + attribute
Cc: Varun Prakash <varun@chelsio.com>
Cc: Hariprasad Shenai <hariprasad@chelsio.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of special casing the handful of callers that check for
iser-target rdma verbs specific shutdown, use a simple flag at
iscsit_transport->rdma_shutdown so each driver can signal this.
Also, update iscsi-target/tcp + cxgbit to rdma_shutdown = false.
Cc: Varun Prakash <varun@chelsio.com>
Cc: Hariprasad Shenai <hariprasad@chelsio.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Go ahead and fold the duplicate iscsi_tpg_np driver attribute
show/store functions into generic callers, invoked by current
driver specific functions.
This allows for future v4.8+ changes to have iscsi_target_mod
use tpg_np driver attributes at runtime, instead of having
the defaults hardcoded in iscsi_target_configfs.c.
Also, drop the unused/legacy 'sctp' attribute for non standard
RFC-3720 operation with IPPROTO_SCTP.
Cc: Varun Prakash <varun@chelsio.com>
Cc: Hariprasad Shenai <hariprasad@chelsio.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The SRP target driver will need to allocate and chain it's own SGLs soon.
For this export target_alloc_sgl, and add a new argument to it so that it
can allocate an additional chain entry that doesn't point to a page. Also
export transport_free_sgl after renaming it to target_free_sgl to free
these SGLs again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ensures the first page entry is within bounds. A failed check would
terminate the iSCSI connection instead of causing a NULL-dereference.
This violation seems to happen with certain iSCSI commands where the
computed CDB length is zero but the expected transfer length is
non-zero. The real problem is probably on the iSCSI initiator side
since there is a discrepancy between the iSCSI header and the
encapsulated CDB Opcode.
Signed-off-by: Imran Haider <imran1008@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The removal the #ifdef'd code on CONFIG_ARCH_HAS_SG_CHAIN in
commit 02c4de53ad ("target/rd: always chain S/G list")
removed the setting of need_to_release to true, so we are now left
with need_to_release always being false and hence the conditional
kfree is never reached. Clean up the dead code by removing need_to_release
and the conditional kfree.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
