Allow users of dcache_by_line_op to specify cvadp as an op.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Following assembly code is not trivial; make it slightly easier to read by
replacing some of the magic numbers with the defines which are already
present in sysreg.h.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On the Fujitsu-A64FX cores ver(1.0, 1.1), memory access may cause
an undefined fault (Data abort, DFSC=0b111111). This fault occurs under
a specific hardware condition when a load/store instruction performs an
address translation. Any load/store instruction, except non-fault access
including Armv8 and SVE might cause this undefined fault.
The TCR_ELx.NFD1 bit is used by the kernel when CONFIG_RANDOMIZE_BASE
is enabled to mitigate timing attacks against KASLR where the kernel
address space could be probed using the FFR and suppressed fault on
SVE loads.
Since this erratum causes spurious exceptions, which may corrupt
the exception registers, we clear the TCR_ELx.NFDx=1 bits when
booting on an affected CPU.
Signed-off-by: Zhang Lei <zhang.lei@jp.fujitsu.com>
[Generated MIDR value/mask for __cpu_setup(), removed spurious-fault handler
and always disabled the NFDx bits on affected CPUs]
Signed-off-by: James Morse <james.morse@arm.com>
Tested-by: zhang.lei <zhang.lei@jp.fujitsu.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The assembly macro get_thread_info() actually returns a task_struct and is
analogous to the current/get_current macro/function.
While it could be argued that thread_info sits at the start of
task_struct and the intention could have been to return a thread_info,
instances of loads from/stores to the address obtained from
get_thread_info() use offsets that are generated with
offsetof(struct task_struct, [...]).
Rename get_thread_info() to state it returns a task_struct.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There are some helpers to modify PSR.[DAIF] bits that are not referenced
anywhere. The less these bits are available outside of local_irq_*
functions the better.
Get rid of those unused helpers.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 3962446922 ("arm64: preempt: Provide our own implementation of
asm/preempt.h") extended the preempt count field in struct thread_info
to 64 bits, so that it consists of a 32-bit count plus a 32-bit flag
indicating whether or not the current task needs rescheduling.
Whilst the asm-offsets definition of TSK_TI_PREEMPT was updated to point
to this new field, the assembly usage was left untouched meaning that a
32-bit load from TSK_TI_PREEMPT on a big-endian machine actually returns
the reschedule flag instead of the count.
Whilst we could fix this by pointing TSK_TI_PREEMPT at the count field,
we're actually better off reworking the two assembly users so that they
operate on the whole 64-bit value in favour of inspecting the thread
flags separately in order to determine whether a reschedule is needed.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Enabling 52-bit VAs for userspace is pretty confusing, since it requires
you to select "48-bit" virtual addressing in the Kconfig.
Rework the logic so that 52-bit user virtual addressing is advertised in
the "Virtual address space size" choice, along with some help text to
describe its interaction with Pointer Authentication. The EXPERT-only
option to force all user mappings to the 52-bit range is then made
available immediately below the VA size selection.
Signed-off-by: Will Deacon <will.deacon@arm.com>
On arm64 there is optional support for a 52-bit virtual address space.
To exploit this one has to be running with a 64KB page size and be
running on hardware that supports this.
For an arm64 kernel supporting a 48 bit VA with a 64KB page size,
some changes are needed to support a 52-bit userspace:
* TCR_EL1.T0SZ needs to be 12 instead of 16,
* TASK_SIZE needs to reflect the new size.
This patch implements the above when the support for 52-bit VAs is
detected at early boot time.
On arm64 userspace addresses translation is controlled by TTBR0_EL1. As
well as userspace, TTBR0_EL1 controls:
* The identity mapping,
* EFI runtime code.
It is possible to run a kernel with an identity mapping that has a
larger VA size than userspace (and for this case __cpu_set_tcr_t0sz()
would set TCR_EL1.T0SZ as appropriate). However, when the conditions for
52-bit userspace are met; it is possible to keep TCR_EL1.T0SZ fixed at
12. Thus in this patch, the TCR_EL1.T0SZ size changing logic is
disabled.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Enabling 52-bit VAs on arm64 requires that the PGD table expands from 64
entries (for the 48-bit case) to 1024 entries. This quantity,
PTRS_PER_PGD is used as follows to compute which PGD entry corresponds
to a given virtual address, addr:
pgd_index(addr) -> (addr >> PGDIR_SHIFT) & (PTRS_PER_PGD - 1)
Userspace addresses are prefixed by 0's, so for a 48-bit userspace
address, uva, the following is true:
(uva >> PGDIR_SHIFT) & (1024 - 1) == (uva >> PGDIR_SHIFT) & (64 - 1)
In other words, a 48-bit userspace address will have the same pgd_index
when using PTRS_PER_PGD = 64 and 1024.
Kernel addresses are prefixed by 1's so, given a 48-bit kernel address,
kva, we have the following inequality:
(kva >> PGDIR_SHIFT) & (1024 - 1) != (kva >> PGDIR_SHIFT) & (64 - 1)
In other words a 48-bit kernel virtual address will have a different
pgd_index when using PTRS_PER_PGD = 64 and 1024.
If, however, we note that:
kva = 0xFFFF << 48 + lower (where lower[63:48] == 0b)
and, PGDIR_SHIFT = 42 (as we are dealing with 64KB PAGE_SIZE)
We can consider:
(kva >> PGDIR_SHIFT) & (1024 - 1) - (kva >> PGDIR_SHIFT) & (64 - 1)
= (0xFFFF << 6) & 0x3FF - (0xFFFF << 6) & 0x3F // "lower" cancels out
= 0x3C0
In other words, one can switch PTRS_PER_PGD to the 52-bit value globally
provided that they increment ttbr1_el1 by 0x3C0 * 8 = 0x1E00 bytes when
running with 48-bit kernel VAs (TCR_EL1.T1SZ = 16).
For kernel configuration where 52-bit userspace VAs are possible, this
patch offsets ttbr1_el1 and sets PTRS_PER_PGD corresponding to the
52-bit value.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Steve Capper <steve.capper@arm.com>
[will: added comment to TTBR1_BADDR_4852_OFFSET calculation]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The dcache_by_line_op macro suffers from a couple of small problems:
First, the GAS directives that are currently being used rely on
assembler behavior that is not documented, and probably not guaranteed
to produce the correct behavior going forward. As a result, we end up
with some undefined symbols in cache.o:
$ nm arch/arm64/mm/cache.o
...
U civac
...
U cvac
U cvap
U cvau
This is due to the fact that the comparisons used to select the
operation type in the dcache_by_line_op macro are comparing symbols
not strings, and even though it seems that GAS is doing the right
thing here (undefined symbols by the same name are equal to each
other), it seems unwise to rely on this.
Second, when patching in a DC CVAP instruction on CPUs that support it,
the fallback path consists of a DC CVAU instruction which may be
affected by CPU errata that require ARM64_WORKAROUND_CLEAN_CACHE.
Solve these issues by unrolling the various maintenance routines and
using the conditional directives that are documented as operating on
strings. To avoid the complexity of nested alternatives, we move the
DC CVAP patching to __clean_dcache_area_pop, falling back to a branch
to __clean_dcache_area_poc if DCPOP is not supported by the CPU.
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
So that we can export symbols directly from assembly files, let's make
use of the generic <asm/export.h>. We have a few symbols that we'll want
to conditionally export for !KASAN kernel builds, so we add a helper for
that in <asm/assembler.h>.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We currently use a DSB; ISB sequence to inhibit speculation in set_fs().
Whilst this works for current CPUs, future CPUs may implement a new SB
barrier instruction which acts as an architected speculation barrier.
On CPUs that support it, patch in an SB; NOP sequence over the DSB; ISB
sequence and advertise the presence of the new instruction to userspace.
Signed-off-by: Will Deacon <will.deacon@arm.com>
There's no need to treat mismatched cache-line sizes reported by CTR_EL0
differently to any other mismatched fields that we treat as "STRICT" in
the cpufeature code. In both cases we need to trap and emulate EL0
accesses to the register, so drop ARM64_MISMATCHED_CACHE_LINE_SIZE and
rely on ARM64_MISMATCHED_CACHE_TYPE instead.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: move ARM64_HAS_CNP in the empty cpucaps.h slot]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add support macros to conditionally yield the NEON (and thus the CPU)
that may be called from the assembler code.
In some cases, yielding the NEON involves saving and restoring a non
trivial amount of context (especially in the CRC folding algorithms),
and so the macro is split into three, and the code in between is only
executed when the yield path is taken, allowing the context to be preserved.
The third macro takes an optional label argument that marks the resume
path after a yield has been performed.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We are going to add code to all the NEON crypto routines that will
turn them into non-leaf functions, so we need to manage the stack
frames. To make this less tedious and error prone, add some macros
that take the number of callee saved registers to preserve and the
extra size to allocate in the stack frame (for locals) and emit
the ldp/stp sequences.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we started keeping modules within 4 GB of the core kernel
in all cases, we no longer need to special case the adr_l/ldr_l/str_l
macros for modules to deal with them being loaded farther away.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM:
- Include icache invalidation optimizations, improving VM startup time
- Support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- A small fix for power-management notifiers, and some cosmetic changes
PPC:
- Add MMIO emulation for vector loads and stores
- Allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- Improve the handling of escalation interrupts with the XIVE interrupt
controller
- Support decrement register migration
- Various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- Exitless interrupts for emulated devices
- Cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- Hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- Paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- Allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more AVX512
features
- Show vcpu id in its anonymous inode name
- Many fixes and cleanups
- Per-VCPU MSR bitmaps (already merged through x86/pti branch)
- Stable KVM clock when nesting on Hyper-V (merged through x86/hyperv)
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJafvMtAAoJEED/6hsPKofo6YcH/Rzf2RmshrWaC3q82yfIV0Qz
Z8N8yJHSaSdc3Jo6cmiVj0zelwAxdQcyjwlT7vxt5SL2yML+/Q0st9Hc3EgGGXPm
Il99eJEl+2MYpZgYZqV8ff3mHS5s5Jms+7BITAeh6Rgt+DyNbykEAvzt+MCHK9cP
xtsIZQlvRF7HIrpOlaRzOPp3sK2/MDZJ1RBE7wYItK3CUAmsHim/LVYKzZkRTij3
/9b4LP1yMMbziG+Yxt1o682EwJB5YIat6fmDG9uFeEVI5rWWN7WFubqs8gCjYy/p
FX+BjpOdgTRnX+1m9GIj0Jlc/HKMXryDfSZS07Zy4FbGEwSiI5SfKECub4mDhuE=
=C/uD
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"ARM:
- icache invalidation optimizations, improving VM startup time
- support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- a small fix for power-management notifiers, and some cosmetic
changes
PPC:
- add MMIO emulation for vector loads and stores
- allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- improve the handling of escalation interrupts with the XIVE
interrupt controller
- support decrement register migration
- various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- exitless interrupts for emulated devices
- cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more
AVX512 features
- show vcpu id in its anonymous inode name
- many fixes and cleanups
- per-VCPU MSR bitmaps (already merged through x86/pti branch)
- stable KVM clock when nesting on Hyper-V (merged through
x86/hyperv)"
* tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits)
KVM: PPC: Book3S: Add MMIO emulation for VMX instructions
KVM: PPC: Book3S HV: Branch inside feature section
KVM: PPC: Book3S HV: Make HPT resizing work on POWER9
KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code
KVM: PPC: Book3S PR: Fix broken select due to misspelling
KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs()
KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled
KVM: PPC: Book3S HV: Drop locks before reading guest memory
kvm: x86: remove efer_reload entry in kvm_vcpu_stat
KVM: x86: AMD Processor Topology Information
x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested
kvm: embed vcpu id to dentry of vcpu anon inode
kvm: Map PFN-type memory regions as writable (if possible)
x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n
KVM: arm/arm64: Fixup userspace irqchip static key optimization
KVM: arm/arm64: Fix userspace_irqchip_in_use counting
KVM: arm/arm64: Fix incorrect timer_is_pending logic
MAINTAINERS: update KVM/s390 maintainers
MAINTAINERS: add Halil as additional vfio-ccw maintainer
MAINTAINERS: add David as a reviewer for KVM/s390
...
In a similar manner to array_index_mask_nospec, this patch introduces an
assembly macro (mask_nospec64) which can be used to bound a value under
speculation. This macro is then used to ensure that the indirect branch
through the syscall table is bounded under speculation, with out-of-range
addresses speculating as calls to sys_io_setup (0).
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For CPUs capable of data value prediction, CSDB waits for any outstanding
predictions to architecturally resolve before allowing speculative execution
to continue. Provide macros to expose it to the arch code.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
pte_to_phys lives in assembler.h and takes its destination register as
the first argument. Move phys_to_pte out of head.S to sit with its
counterpart and rejig it to follow the same calling convention.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since AArch64 assembly instructions take the destination register as
their first operand, do the same thing for the phys_to_ttbr macro.
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Defaulting to global mappings for kernel space is generally good for
performance and appears to be necessary for Cavium ThunderX. If we
subsequently decide that we need to enable kpti, then we need to rewrite
our existing page table entries to be non-global. This is fiddly, and
made worse by the possible use of contiguous mappings, which require
a strict break-before-make sequence.
Since the enable callback runs on each online CPU from stop_machine
context, we can have all CPUs enter the idmap, where secondaries can
wait for the primary CPU to rewrite swapper with its MMU off. It's all
fairly horrible, but at least it only runs once.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The ARM architecture defines the memory locations that are permitted
to be accessed as the result of a speculative instruction fetch from
an exception level for which all stages of translation are disabled.
Specifically, the core is permitted to speculatively fetch from the
4KB region containing the current program counter 4K and next 4K.
When translation is changed from enabled to disabled for the running
exception level (SCTLR_ELn[M] changed from a value of 1 to 0), the
Falkor core may errantly speculatively access memory locations outside
of the 4KB region permitted by the architecture. The errant memory
access may lead to one of the following unexpected behaviors.
1) A System Error Interrupt (SEI) being raised by the Falkor core due
to the errant memory access attempting to access a region of memory
that is protected by a slave-side memory protection unit.
2) Unpredictable device behavior due to a speculative read from device
memory. This behavior may only occur if the instruction cache is
disabled prior to or coincident with translation being changed from
enabled to disabled.
The conditions leading to this erratum will not occur when either of the
following occur:
1) A higher exception level disables translation of a lower exception level
(e.g. EL2 changing SCTLR_EL1[M] from a value of 1 to 0).
2) An exception level disabling its stage-1 translation if its stage-2
translation is enabled (e.g. EL1 changing SCTLR_EL1[M] from a value of 1
to 0 when HCR_EL2[VM] has a value of 1).
To avoid the errant behavior, software must execute an ISB immediately
prior to executing the MSR that will change SCTLR_ELn[M] from 1 to 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
KVM would like to consume any pending SError (or RAS error) after guest
exit. Today it has to unmask SError and use dsb+isb to synchronise the
CPU. With the RAS extensions we can use ESB to synchronise any pending
SError.
Add the necessary macros to allow DISR to be read and converted to an
ESR.
We clear the DISR register when we enable the RAS cpufeature, and the
kernel has not executed any ESB instructions. Any value we find in DISR
must have belonged to firmware. Executing an ESB instruction is the
only way to update DISR, so we can expect firmware to have handled
any deferred SError. By the same logic we clear DISR in the idle path.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The 'pos' argument is used to select where in TCR to write the value:
the IPS or PS bitfield.
Fixes: 787fd1d019 ("arm64: limit PA size to supported range")
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that KVM uses tpidr_el2 in the same way as Linux's cpu_offset in
tpidr_el1, merge the two. This saves KVM from save/restoring tpidr_el1
on VHE hosts, and allows future code to blindly access per-cpu variables
without triggering world-switch.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We will soon need to invoke a CPU-specific function pointer after changing
page tables, so move post_ttbr_update_workaround out into C code to make
this possible.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We currently tightly couple dcache clean with icache invalidation,
but KVM could do without the initial flush to PoU, as we've
already flushed things to PoC.
Let's introduce invalidate_icache_range which is limited to
invalidating the icache from the linear mapping (and thus
has none of the userspace fault handling complexity), and
wire it in KVM instead of flush_icache_range.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
* for-next/52-bit-pa:
arm64: enable 52-bit physical address support
arm64: allow ID map to be extended to 52 bits
arm64: handle 52-bit physical addresses in page table entries
arm64: don't open code page table entry creation
arm64: head.S: handle 52-bit PAs in PTEs in early page table setup
arm64: handle 52-bit addresses in TTBR
arm64: limit PA size to supported range
arm64: add kconfig symbol to configure physical address size
Currently, when using VA_BITS < 48, if the ID map text happens to be
placed in physical memory above VA_BITS, we increase the VA size (up to
48) and create a new table level, in order to map in the ID map text.
This is okay because the system always supports 48 bits of VA.
This patch extends the code such that if the system supports 52 bits of
VA, and the ID map text is placed that high up, then we increase the VA
size accordingly, up to 52.
One difference from the current implementation is that so far the
condition of VA_BITS < 48 has meant that the top level table is always
"full", with the maximum number of entries, and an extra table level is
always needed. Now, when VA_BITS = 48 (and using 64k pages), the top
level table is not full, and we simply need to increase the number of
entries in it, instead of creating a new table level.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: reduce arguments to __create_hyp_mappings()]
[catalin.marinas@arm.com: reworked/renamed __cpu_uses_extended_idmap_level()]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The top 4 bits of a 52-bit physical address are positioned at bits 2..5
in the TTBR registers. Introduce a couple of macros to move the bits
there, and change all TTBR writers to use them.
Leave TTBR0 PAN code unchanged, to avoid complicating it. A system with
52-bit PA will have PAN anyway (because it's ARMv8.1 or later), and a
system without 52-bit PA can only use up to 48-bit PAs. A later patch in
this series will add a kconfig dependency to ensure PAN is configured.
In addition, when using 52-bit PA there is a special alignment
requirement on the top-level table. We don't currently have any VA_BITS
configuration that would violate the requirement, but one could be added
in the future, so add a compile-time BUG_ON to check for it.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: added TTBR_BADD_MASK_52 comment]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We currently copy the physical address size from
ID_AA64MMFR0_EL1.PARange directly into TCR.(I)PS. This will not work for
4k and 16k granule kernels on systems that support 52-bit physical
addresses, since 52-bit addresses are only permitted with the 64k
granule.
To fix this, fall back to 48 bits when configuring the PA size when the
kernel does not support 52-bit PAs. When it does, fall back to 52, to
avoid similar problems in the future if the PA size is ever increased
above 52.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: tcr_set_pa_size macro renamed to tcr_compute_pa_size]
[catalin.marinas@arm.com: comments added to tcr_compute_pa_size]
[catalin.marinas@arm.com: definitions added for TCR_*PS_SHIFT]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The ARM architecture defines the memory locations that are permitted
to be accessed as the result of a speculative instruction fetch from
an exception level for which all stages of translation are disabled.
Specifically, the core is permitted to speculatively fetch from the
4KB region containing the current program counter 4K and next 4K.
When translation is changed from enabled to disabled for the running
exception level (SCTLR_ELn[M] changed from a value of 1 to 0), the
Falkor core may errantly speculatively access memory locations outside
of the 4KB region permitted by the architecture. The errant memory
access may lead to one of the following unexpected behaviors.
1) A System Error Interrupt (SEI) being raised by the Falkor core due
to the errant memory access attempting to access a region of memory
that is protected by a slave-side memory protection unit.
2) Unpredictable device behavior due to a speculative read from device
memory. This behavior may only occur if the instruction cache is
disabled prior to or coincident with translation being changed from
enabled to disabled.
The conditions leading to this erratum will not occur when either of the
following occur:
1) A higher exception level disables translation of a lower exception level
(e.g. EL2 changing SCTLR_EL1[M] from a value of 1 to 0).
2) An exception level disabling its stage-1 translation if its stage-2
translation is enabled (e.g. EL1 changing SCTLR_EL1[M] from a value of 1
to 0 when HCR_EL2[VM] has a value of 1).
To avoid the errant behavior, software must execute an ISB immediately
prior to executing the MSR that will change SCTLR_ELn[M] from 1 to 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The post_ttbr0_update_workaround hook applies to any change to TTBRx_EL1.
Since we're using TTBR1 for the ASID, rename the hook to make it clearer
as to what it's doing.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Tested-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The pre_ttbr0_update_workaround hook is called prior to context-switching
TTBR0 because Falkor erratum E1003 can cause TLB allocation with the wrong
ASID if both the ASID and the base address of the TTBR are updated at
the same time.
With the ASID sitting safely in TTBR1, we no longer update things
atomically, so we can remove the pre_ttbr0_update_workaround macro as
it's no longer required. The erratum infrastructure and documentation
is left around for #E1003, as it will be required by the entry
trampoline code in a future patch.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Tested-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Following our 'dai' order, irqs should be processed with debug and
serror exceptions unmasked.
Add a helper to unmask these two, (and fiq for good measure).
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
el0_sync also unmasks exceptions on a case-by-case basis, debug exceptions
are enabled, unless this was a debug exception. Irqs are unmasked for
some exception types but not for others.
el0_dbg should run with everything masked to prevent us taking a debug
exception from do_debug_exception. For the other cases we can unmask
everything. This changes the behaviour of fpsimd_{acc,exc} and el0_inv
which previously ran with irqs masked.
This patch removed the last user of enable_dbg_and_irq, remove it.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
el1_sync unmasks exceptions on a case-by-case basis, debug exceptions
are unmasked, unless this was a debug exception. IRQs are unmasked
for instruction and data aborts only if the interupted context had
irqs unmasked.
Following our 'dai' order, el1_dbg should run with everything masked.
For the other cases we can inherit whatever we interrupted.
Add a macro inherit_daif to set daif based on the interrupted pstate.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
enable_step_tsk is the only user of disable_dbg, which doesn't respect
our 'dai' order for exception masking. enable_step_tsk may enable
single-step, so previously needed to mask debug exceptions to prevent us
from single-stepping kernel_exit. enable_step_tsk is called at the end
of the ret_to_user loop, which has already masked all exceptions so this
is no longer needed.
Remove disable_dbg, add a comment that enable_step_tsk's caller should
have masked debug.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are a few places where we want to mask all exceptions. Today we
do this in a piecemeal fashion, typically we expect the caller to
have masked irqs and the arch code masks debug exceptions, ignoring
serror which is probably masked.
Make it clear that 'mask all exceptions' is the intention by adding
helpers to do exactly that.
This will let us unmask SError without having to add 'oh and SError'
to these paths.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Literal values are being used to set single stepping in mdscr from assembly
code. There are already existing defines representing those values, use
those instead of the literal values.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Given that adr_this_cpu already requires a temp register in addition
to the destination register, tweak the instruction sequence so that sp
may be used as well.
This will simplify switching to per-cpu stacks in subsequent patches. While
this limits the range of adr_this_cpu, to +/-4GiB, we don't currently use
adr_this_cpu in modules, and this is not problematic for the main kernel image.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[Mark: add more commit text]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Add a clean-to-point-of-persistence cache maintenance helper, and wire
up the basic architectural support for the pmem driver based on it.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[catalin.marinas@arm.com: move arch_*_pmem() functions to arch/arm64/mm/flush.c]
[catalin.marinas@arm.com: change dmb(sy) to dmb(osh)]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently, cpu_switch_to and ret_from_fork both live in .entry.text,
though neither form the critical path for an exception entry.
In subsequent patches, we will require that code in .entry.text is part
of the critical path for exception entry, for which we can assume
certain properties (e.g. the presence of exception regs on the stack).
Neither cpu_switch_to nor ret_from_fork will meet these requirements, so
we must move them out of .entry.text. To ensure that neither are kprobed
after being moved out of .entry.text, we must explicitly blacklist them,
requiring a new NOKPROBE() asm helper.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
- Errata workarounds for Qualcomm's Falkor CPU
- Qualcomm L2 Cache PMU driver
- Qualcomm SMCCC firmware quirk
- Support for DEBUG_VIRTUAL
- CPU feature detection for userspace via MRS emulation
- Preliminary work for the Statistical Profiling Extension
- Misc cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJYpIxqAAoJELescNyEwWM0xdwH/AsTYAXPZDMdRnrQUyV0Fd2H
/9pMzww6dHXEmCMKkImf++otUD6S+gTCJTsj7kEAXT5sZzLk27std5lsW7R9oPjc
bGQMalZy+ovLR1gJ6v072seM3In4xph/qAYOpD8Q0AfYCLHjfMMArQfoLa8Esgru
eSsrAgzVAkrK7XHi3sYycUjr9Hac9tvOOuQ3SaZkDz4MfFIbI4b43+c1SCF7wgT9
tQUHLhhxzGmgxjViI2lLYZuBWsIWsE+algvOe1qocvA9JEIXF+W8NeOuCjdL8WwX
3aoqYClC+qD/9+/skShFv5gM5fo0/IweLTUNIHADXpB6OkCYDyg+sxNM+xnEWQU=
=YrPg
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
- Errata workarounds for Qualcomm's Falkor CPU
- Qualcomm L2 Cache PMU driver
- Qualcomm SMCCC firmware quirk
- Support for DEBUG_VIRTUAL
- CPU feature detection for userspace via MRS emulation
- Preliminary work for the Statistical Profiling Extension
- Misc cleanups and non-critical fixes
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (74 commits)
arm64/kprobes: consistently handle MRS/MSR with XZR
arm64: cpufeature: correctly handle MRS to XZR
arm64: traps: correctly handle MRS/MSR with XZR
arm64: ptrace: add XZR-safe regs accessors
arm64: include asm/assembler.h in entry-ftrace.S
arm64: fix warning about swapper_pg_dir overflow
arm64: Work around Falkor erratum 1003
arm64: head.S: Enable EL1 (host) access to SPE when entered at EL2
arm64: arch_timer: document Hisilicon erratum 161010101
arm64: use is_vmalloc_addr
arm64: use linux/sizes.h for constants
arm64: uaccess: consistently check object sizes
perf: add qcom l2 cache perf events driver
arm64: remove wrong CONFIG_PROC_SYSCTL ifdef
ARM: smccc: Update HVC comment to describe new quirk parameter
arm64: do not trace atomic operations
ACPI/IORT: Fix the error return code in iort_add_smmu_platform_device()
ACPI/IORT: Fix iort_node_get_id() mapping entries indexing
arm64: mm: enable CONFIG_HOLES_IN_ZONE for NUMA
perf: xgene: Include module.h
...
The Qualcomm Datacenter Technologies Falkor v1 CPU may allocate TLB entries
using an incorrect ASID when TTBRx_EL1 is being updated. When the erratum
is triggered, page table entries using the new translation table base
address (BADDR) will be allocated into the TLB using the old ASID. All
circumstances leading to the incorrect ASID being cached in the TLB arise
when software writes TTBRx_EL1[ASID] and TTBRx_EL1[BADDR], a memory
operation is in the process of performing a translation using the specific
TTBRx_EL1 being written, and the memory operation uses a translation table
descriptor designated as non-global. EL2 and EL3 code changing the EL1&0
ASID is not subject to this erratum because hardware is prohibited from
performing translations from an out-of-context translation regime.
Consider the following pseudo code.
write new BADDR and ASID values to TTBRx_EL1
Replacing the above sequence with the one below will ensure that no TLB
entries with an incorrect ASID are used by software.
write reserved value to TTBRx_EL1[ASID]
ISB
write new value to TTBRx_EL1[BADDR]
ISB
write new value to TTBRx_EL1[ASID]
ISB
When the above sequence is used, page table entries using the new BADDR
value may still be incorrectly allocated into the TLB using the reserved
ASID. Yet this will not reduce functionality, since TLB entries incorrectly
tagged with the reserved ASID will never be hit by a later instruction.
Based on work by Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When CONFIG_RANDOMIZE_MODULE_REGION_FULL=y, the offset between loaded
modules and the core kernel may exceed 4 GB, putting symbols exported
by the core kernel out of the reach of the ordinary adrp/add instruction
pairs used to generate relative symbol references. So make the adr_l
macro emit a movz/movk sequence instead when executing in module context.
While at it, remove the pointless special case for the stack pointer.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
