The Amlogic S805X/Y uses the same die as the S905X, but with more
limited graphics capabilities.
This adds a soc version detection adding specific limitations on the HDMI
mode selections.
Here, we limit to HDMI 1.2a max HDMI PHY clock frequency.
Changes sinces v1:
- Moved frequency check in the vclk code, and also checks DMT modes
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[narmstrong: fixed commit message with HDMI 1.2a instead of HDMI 1.3a]
Link: https://patchwork.freedesktop.org/patch/msgid/20200428092147.13698-1-narmstrong@baylibre.com
This patch adds clocking support for the YUV420 output from the
Amlogic Meson SoCs Video Processing Unit to the HDMI Controller.
The YUV420 is obtained by generating a YUV444 pixel stream like
the classic HDMI display modes, but then the Video Encoder output
can be configured to down-sample the YUV444 pixel stream to a YUV420
stream.
This mode needs a different clock generation scheme since the TMDS PHY
clock must match the 10x ratio with the YUV420 pixel clock, but
the video encoder must run at 2x the pixel clock.
This patch adds the TMDS PHY clock value in all the video clock setup
in order to better support these specific uses cases and switch
to the Common Clock framework for clocks handling in the future.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-11-narmstrong@baylibre.com
When calculating the HDMI PLL settings for a DMT mode PHY frequency,
use the correct max fractional PLL value for G12A VPU.
With this fix, we can finally setup the 1024x768-60 mode.
Fixes: 202b9808f8 ("drm/meson: Add G12A Video Clock setup")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828132311.23881-1-narmstrong@baylibre.com
This patch introduce new enum which contains all VPU family (GXBB,
GXL, GXM and G12A).
This enum is used to detect the VPU compatible with the device.
We only need to set .data to the corresponding enum in the device
table, no need to check .compatible string anymore.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87imqpz21w.fsf@masson.i-did-not-set--mail-host-address--so-tickle-me
This patch add new macro HHI_HDMI_PLL_CNTL_EN which is used to enable
HDMI PLL.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/86o92n82e1.fsf@baylibre.com
This patch aims to:
- Add general and TODO comments
- Respect coding style for multi-line comments
- Align macro definitions
- Remove useless macro
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/86pnn382e8.fsf@baylibre.com
Drop use of the deprecated drmP.h header.
While doing so used the opportunity
to clean up a little so includes are now
sorted and removed unused include files.
In a few cases added some forwards to allow header
files to built in different include order.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Maxime Jourdan <mjourdan@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190716064220.18157-2-sam@ravnborg.org
The Amlogic G12A HDMI PLL needs some specific settings to lock with
different fractional values for the 5,4GHz mode.
Handle the 1000/1001 variation fractional case here to avoid having
the PLL in an non lockable state.
Fixes: 202b9808f8 ("drm/meson: Add G12A Video Clock setup")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190605125320.8708-1-narmstrong@baylibre.com
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While switching to the Common Clock Framework is still Work In Progress,
this patch adds the corresponding G12A HDMI PLL setup to be on-par
with the other SoCs support.
The G12A has only a single tweak about the high frequency setup,
where the HDMI PLL needs a specific setup to handle correctly the
5.94GHz DCO frequency.
Apart that, it handls ecorrectly all the other HDMI frequencies
and can achieve even better DMT clock frequency precision with
the larger fractional dividier width.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-10-narmstrong@baylibre.com
On Amlogic G12A SoC, the 2,97GHz PLL frequency is not stable enough
to provide a correct 297MHz pixel clock, so switch the PLL base
frequency with a /2 OD when the 297MHz pixel clock is requested.
This solves the issue on G12A and also works fine on GXBB, GXL & GXM.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-2-narmstrong@baylibre.com
This change is an attempt to handle the alternate clock for the CEA mode.
60Hz vs. 59.94Hz, 30Hz vs 29.97Hz or 24Hz vs 23.97Hz on the Amlogic Meson SoC
DRM Driver pixel clock generation.
The actual clock generation will be moved to the Common Clock framework once
all the video clock are handled by the Amlogic Meson SoC clock driver,
then these alternate timings will be handled in the same time in a cleaner
fashion.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
[narmstrong: fix maybe-uninitialized warnings after applying]
Link: https://patchwork.freedesktop.org/patch/msgid/1541501675-3928-1-git-send-email-narmstrong@baylibre.com
Remove the modes timings tables for DMT modes and calculate the HW
paremeters from the modes timings.
Switch the DMT modes pixel clock calculation out of the static frequency
list to a generic calculation from a range of possible PLL dividers.
This patch is an intermediate step towards usage of the Common Clock
Framwework for PLL setup, by reworking the code to have common
sel_pll() function called by the CEA (HDMI) freq setup and the generic
DMT frequencies setup, we should be able to simply call clk_set_rate()
on the PLL clock handle in a near future.
The CEA (HDMI) and CVBS modes needs very specific clock paths that CCF will
never be able to determine by itself, so there is still some work to do for
a full handoff to CCF handling the clocks.
This setup permits setting non-CEA modes like :
- 1600x900-60Hz
- 1280x1024-75Hz
- 1280x1024-60Hz
- 1440x900-60Hz
- 1366x768-60Hz
- 1280x800-60Hz
- 1152x864-75Hz
- 1024x768-75Hz
- 1024x768-70Hz
- 1024x768-60Hz
- 832x624-75Hz
- 800x600-75Hz
- 800x600-72Hz
- 800x600-60Hz
- 640x480-75Hz
- 640x480-73Hz
- 640x480-67Hz
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: fixed trivial checkpatch issues]
Link: https://patchwork.freedesktop.org/patch/msgid/1531726814-14638-1-git-send-email-narmstrong@baylibre.com
This patch adds support for DMT display modes over HDMI.
The modes timings configurations are from the Amlogic Vendor linux tree
and tested over multiples monitors.
Previously only a selected number of CEA modes were supported.
Only these following modes are supported with these changes:
- 640x480@60Hz
- 800x600@60Hz
- 1024x768@60Hz
- 1152x864@75Hz
- 1280x1024@60Hz
- 1600x1200@60Hz
- 1920x1080@60Hz
The associated code to handle the clock rates is also added.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520935670-14187-1-git-send-email-narmstrong@baylibre.com
This patchs adds support for the supported HDMI modes clocks frequencies.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic Meson Display controller is composed of several components :
DMC|---------------VPU (Video Processing Unit)----------------|------HHI------|
| vd1 _______ _____________ _________________ | |
D |-------| |----| | | | | HDMI PLL |
D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK |
R |-------| |----| Processing | | | | |
| osd2 | | | |---| Enci ----------|----|-----VDAC------|
R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----|
A | osd1 | | | Blenders | | Encl ----------|----|---------------|
M |-------|______|----|____________| |________________| | |
___|__________________________________________________________|_______________|
VIU: Video Input Unit
---------------------
The Video Input Unit is in charge of the pixel scanout from the DDR memory.
It fetches the frames addresses, stride and parameters from the "Canvas" memory.
This part is also in charge of the CSC (Colorspace Conversion).
It can handle 2 OSD Planes and 2 Video Planes.
VPP: Video Post Processing
--------------------------
The Video Post Processing is in charge of the scaling and blending of the
various planes into a single pixel stream.
There is a special "pre-blending" used by the video planes with a dedicated
scaler and a "post-blending" to merge with the OSD Planes.
The OSD planes also have a dedicated scaler for one of the OSD.
VENC: Video Encoders
--------------------
The VENC is composed of the multiple pixel encoders :
- ENCI : Interlace Video encoder for CVBS and Interlace HDMI
- ENCP : Progressive Video Encoder for HDMI
- ENCL : LCD LVDS Encoder
The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock
tree and provides the scanout clock to the VPP and VIU.
The ENCI is connected to a single VDAC for Composite Output.
The ENCI and ENCP are connected to an on-chip HDMI Transceiver.
This driver is a DRM/KMS driver using the following DRM components :
- GEM-CMA
- PRIME-CMA
- Atomic Modesetting
- FBDev-CMA
For the following SoCs :
- GXBB Family (S905)
- GXL Family (S905X, S905D)
- GXM Family (S912)
The current driver only supports the CVBS PAL/NTSC output modes, but the
CRTC/Planes management should support bigger modes.
But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in
a second time.
The Device Tree bindings makes use of the endpoints video interface definitions
to connect to the optional CVBS and in the future the HDMI Connector nodes.
HDMI Support is planned for a next release.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
