Now wakeirq stops working for device if wakeup option for
this device will be reconfigured through sysfs, like:
echo disabled > /sys/devices/platform/extcon_usb1/power/wakeup
echo enabled > /sys/devices/platform/extcon_usb1/power/wakeup
Once above set of commands is executed the device's wakeup_source
opject will be recreated and dev->power.wakeup->wakeirq field will
contain NULL. As result, device_wakeup_arm_wake_irqs() will not arm
wakeirq for the affected device.
Hece, lets try to fix it in the following way:
check for dev->wakeirq field when device_wakeup_attach() is called
and if !NULL re-attach wakeirq to the device
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes the rc6 sysfs counter spontaneously resets,
causing turbostat prints a very large number
as it tries to calcuate % = 100 * (old - new) / interval
When we see (old > new), print ***.**% instead
of a bogus huge number.
Note that this detection is not fool-proof, as the counter
could reset several times and still result in new > old.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Hard-code BXT ART to 19200MHz, so turbostat --debug
can fully enumerate TSC:
CPUID(0x15): eax_crystal: 3 ebx_tsc: 186 ecx_crystal_hz: 0
TSC: 1190 MHz (19200000 Hz * 186 / 3 / 1000000)
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some processors use the Interrupt Response Time Limit (IRTL) MSR value
to describe the maximum IRQ response time latency for deep
package C-states. (Though others have the register, but do not use it)
Lets print it out to give insight into the cases where it is used.
IRTL begain in SNB, with PC3/PC6/PC7, and HSW added PC8/PC9/PC10.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The CPUID.SGX bit was printed, even if --debug was used
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver registers cpuidle devices when a CPU comes online, but it
leaves the registrations in place when a CPU goes offline. The module
exit code only unregisters the currently online CPUs, leaving the
devices for offline CPUs dangling.
This patch changes the driver to clean up all registrations on exit,
even those from CPUs that are offline.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a cpuidle registration error occurs during the hot plug notifier
callback, we should really inform the hot plug machinery instead of
just ignoring the error. This patch changes the callback to properly
return on error.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The helper function, intel_idle_cpu_init, registers one new device
with the cpuidle layer. If the registration should fail, that
function immediately calls intel_idle_cpuidle_devices_uninit() to
unregister every last CPU's device. However, it makes no sense to do
so, when called from the hot plug notifier callback.
This patch moves the call to intel_idle_cpuidle_devices_uninit()
outside of the helper function to the one call site that actually
needs to perform the de-registrations.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver sets the broadcast tick quite early on during probe and does
not clean up again in cast of failure. This patch moves the setup call
after the registration, placing the on_each_cpu() calls within the global
CPU lock region.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The helper function, intel_idle_cpuidle_devices_uninit, frees the
globally allocated per-CPU data. However, this function is invoked
from the hot plug notifier callback at a time when freeing that data
is not safe.
If the call to cpuidle_register_driver() should fail (say, due to lack
of memory), then the driver will free its per-CPU region. On the
*next* CPU_ONLINE event, the driver will happily use the region again
and even free it again if the failure repeats.
This patch fixes the issue by moving the call to free_percpu() outside
of the helper function at the two call sites that actually need to
free the per-CPU data.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the module_init() method, if the per-CPU allocation fails, then the
active cpuidle registration is not cleaned up. This patch fixes the
issue by attempting the allocation before registration, and then
cleaning it up again on registration failure.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the module_exit() method, this driver first frees its per-CPU
pointer, then unregisters a callback making use of the pointer.
Furthermore, the function, intel_idle_cpuidle_devices_uninit, is racy
against CPU hot plugging as it calls for_each_online_cpu().
This patch corrects the issues by unregistering first on the exit path
while holding the hot plug lock.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function, intel_idle_cpuidle_driver_init, makes calls on each CPU
to auto_demotion_disable() and c1e_promotion_disable(). These calls
are redundant, as intel_idle_cpu_init() does the same calls just a bit
later on. They are also premature, as the driver registration may yet
fail.
This patch removes the redundant code.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function, intel_idle_cpuidle_driver_init, delivers no error codes
at all. This patch changes the function to return 'void' instead of
returning zero.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ath.git patches for 4.7. Major changes:
ath10k
* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)
wil6210
* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
ip6_route_output() never returns NULL, so it is not appropriate to
check if the return value is NULL.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch prints pcie scratch registers during firmware dump. They
will be useful for analysing firmware status.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch processes sub AMSDU frame received in AP mode.
If a packet is multicast/broadcast, it is sent to kernel/upper
layer as well as queued back to AP TX queue so that it can be
sent to other associated stations.
If a packet is unicast and RA is present in associated station list,
it is again requeued into AP TX queue.
If a packet is unicast and RA is not in associated station list,
packet is forwarded to kernel to handle routing logic.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bridge packets are enqueued to wmm tx queue, but will not be sent
until main workqeue is scheduled for new interrupt or other
reason. This adds unnecessary delay during traffic.
We will schedule main workqueue when bridge packet is queued.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
skb forwarded to TCP/IP stack doesn't need to allocate in DMA ZONE.
This patch removes GFP_DMA flag in this case to save precious DMA
memory.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the chipsets have two revisions. This patch
selects appropriate firmware by checking revision id.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User can configure wakeup on GTK rekey fail with wowlan.
Added corresponding wakeup reason.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added driver functionality to offload GTK rekey to firmware. When
AP sends new GTK, firmware will update it.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per the vendor driver, it looks like the 8192eu doesn't have LDOA15 /
LDOV12 registers.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8192eu uses the same H2C API as the 8723bu. Call the correct
functions for update_rate_mask() and report_connect().
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8192eu A/B cut parts were incorrectly identified as 8192cu devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With support for more chips being added, use an enum to specify the
chip version.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Improve descriptive names of some registers and add some additional
registers only found on nextgen chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
txdesc40 dword2 gid is a 6 bit field, not a single bit
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the size based naming of TX descriptors. Change the bit
definition namings to indicate which descriptor format they match,
rather than having a device name in the bit name.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two major types of TX descriptor formats for the RTL parts,
the old 32 byte descriptor, and the newer 40 byte descriptor used by
the 8723bu, 8192eu, and 88xx series.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In mwifiex_enable_hs, we need to check if
priv->wdev.wiphy->wowlan_config is NULL before accessing its member.
This sometimes cause kernel panic when suspend/resume.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ap_ie->ie_list is an array of struct mwifiex_ie and can never
be null, so the null check on this array is redundant and can
be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some of the non-success return paths, the memory allocated by
iwl4965_sta_alloc_lq() in iwl4965_alloc_bcast_station() is not freed.
In particular:
- if the card isn't ready after il4965_prepare_card_hw()
- if the card is hardware-rfkilled
In the hardware rfkilled path, the driver enables the rfkill
interrupt. When the card is unrfkilled and this interrupt is raised
we end up calling il4965_bg_restart() which calls __il4965_up() which
calls iwl4965_alloc_bcast_station() again.
Suggested-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When il4965_hw_nic_init in __il4965_up fails, the memory allocated by
iwl4965_sta_alloc_lq in iwl4965_alloc_bcast_station is not freed.
This patches adds il_dealloc_bcast_stations in the error handling code of
__il4965_up to fix this problem.
This patch has been tested in real device, and it actually fixes the bug.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rsi_send_data_pkt(), it's a little more logical to assign 'status' in
the actual error handling code as opposed to at the top of the functon.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[Deleted controversial bits, rewrote commit message]
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rsi_send_data_pkt(), the following variables are assigned to
before they're used:
* tmp_hdr - Assigned on line 47, first used on line 48
* bss - Assigned on line 41, first used on line 44
* extnd_size - Assigned on line 50, first used on line 52
* seq_num - Assigned on line 48, first used on line 96
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[Rewrote commit message]
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rsi_send_mgmt_pkt(), the following variables are assigned to
before they're used:
* wh - Assigned on line 161, first used on line 180
* bss - Assigned on line 160, first used on line 196
* msg - Assigned on line 168, first used on line 175
* extnd_size - Assigned on line 139, first used on line 142
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[Rewrote commit message]
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When pci_request_regions in rtl8180_probe fails, pci_disable_device is not
called to disable the device which is enabled by pci_enbale_device.
This patch fixes the problem by adding a new lable in error handling code.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The memory allocated by kzalloc in b43_bus_dev_ssb_init and
b43_bus_dev_bcma_init is not freed.
This patch fixes the bug by adding kfree in b43_ssb_remove,
b43_bcma_remove and error handling code of b43_bcma_probe.
Thanks Michael for his suggestion.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If "txq->cmd = kzalloc(...)" in il_tx_queue_init fails,
"kfree(txq->cmd[i])" in il_tx_queue_free and il_cmd_queue_free
in iwl4965_hw_txq_ctx_free will causes a null pointer dereference,
because txq->cmd is NULL at that time.
This patch fixes this problem by adding a if-check before kfree.
To avoid double free in il_tx_queue_free and il_cmd_queue_free
caused by the fixing, txq->meta and txq->cmd in error handling code
of il_tx_queue_init are assigned null values.
Otherwise, a double free will occur.
This patch has been tested in real device, and it actually fixes the bug.
Thanks Stanislaw for his suggestion.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Also remove an unused label.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
[Rewrote commit message]
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
