In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fail to set the flooding configuration for the broadcast and
unregistered multicast traffic, we should revert the flooding
configuration of the unknown unicast traffic.
Fixes: 0293038e0c ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the leave procedure in the error path symmetric to the join
procedure and first remove the port from the collector before
potentially destroying the LAG.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement occupancy API introduced in devlink and mlxsw core. This is
done by accessing SBPM register for Port-Pool and SBSR for Port-TC
current and max occupancy values. Max clear is implemented using the
same registers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far it was possible to have one EMAD register access at a time,
locked by mutex. This patch extends this interface to allow multiple
EMAD register accesses to be in fly at once. That allows faster
processing on firmware side avoiding unused time in between EMADs.
Measured speedup is ~30% for shared occupancy snapshot operation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up patch is going to need to use delayed work as well and
frequently. The FDB notification processing is already using that and
also quite frequently. It makes sense to create separate workqueue just
for mlxsw driver in this case and do not pollute system_wq.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is not possible to get and clear Port-Pool occupancy data using
SBSR register, there's a need to implement that using SBPM.
Extend pack helper and add unpack helper to get occupancy values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register allows to query HW for current and maximal buffer usage.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add middle layer in mlxsw core code to forward shared buffer occupancy
calls into specific ASIC drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement previously introduced mlxsw core shared buffer API.
For Spectrum, that is done utilizing registers SBPR, SBCM and SBPM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed in following patch.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the device supports max_buff magic values 0 and 0xff, these are
not exposed to the user via devlink.
Therefore, adjust the default values to be within configurable range.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit ff6551ec0c ("mlxsw: spectrum: Correctly
configure headroom size") control packets are directed to priority group
buffer 9 (PG9) in the ports' headroom buffers.
Since we don't want to drop control packets in case they can't be
admitted to the switch's shared buffer we bind PG9 to a different
ingress pool from the one used by all other PGs.
Unlike other PGs, we currently don't expose the binding between PG9 to a
pool and leave it fixed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is no congestion control for CPU port traffic, we can change
the CPU port TC binding to pool 0 with min_buff and max_buff zeroed.
Remove initialization for pool egress pool 3 since it is no longer used
by dafault.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to achieve faster dumping of current setting and also in order
to provide possibility to get pool mode without a need to query hardware,
do cache the configuration in driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be consintent with rest of the registers (pm, cm) and use "pr" here.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Structs are in arrays so use array index as pool/tc/prio index. With
that, there is need to maintain separate arrays for ingress and egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pushed them into helper functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add middle layer in mlxsw core code to forward shared buffer calls
into specific ASIC drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix copy&paste error and state the name of SBPM register correctly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same field, same values, so share the same enum.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of that, pass mlxsw_core and use a helper to get driver priv
from driver code. Looks much cleaner that way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of passing around driver priv, pass struct mlxsw_core *
directly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove devlink port reg/unreg from spectrum and switchx2 code and rather
do the common work in core. That also ensures code separation where
devlink is only used in core.c.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the appropriate DCB ops and allow a user to configure certain
traffic classes as lossless.
The operation configures PFC for both the egress (respecting PFC frames)
and ingress (sending PFC frames) parts of the port.
At egress, when a PFC frame is received for a PFC enabled priority, then
all the priorities mapped to the same TC are stopped.
At ingress, the priority group (PG) buffers to which the enabled PFC
priorities are mapped are configured to be lossless. PFC frames will be
transmitted when the Xoff threshold is crossed.
The user-supplied delay parameter is used to determine the PG's size
according to the following formula:
PG_SIZE = PG_SIZE_LOSSY + delay * CELL_FACTOR + MTU
In the worst case scenario the delay will be made up of packets that
are all of size CELL_SIZE + 1, which means each packet will require
almost twice its true size when buffered in the switch. We therefore
multiply this value by the "cell factor", which is close to 2.
Another MTU is added in case the transmitting host already started
transmitting a maximum length frame when the PFC packet was received.
As with PAUSE enabled ports, when the port's MTU is changed both the
PGs' size and threshold are adjusted accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to add support for PFC as part of DCB ops, which requires us
to report the number of PFC frames sent and received per priority.
Add per priority counters in order to report number of PFC frames sent
and received per priority.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet ingress the switch it's placed in its assigned priority
group (PG) buffer in the port's headroom buffer while it goes through
the switch's pipeline. After going through the pipeline - which
determines its egress port(s) and traffic class - it's moved to the
switch's shared buffer awaiting transmission.
However, some packets are not eligible to enter the shared buffer due to
exceeded quotas or insufficient space. Marking their associated PGs as
lossless will cause the packets to accumulate in the PG buffer. Another
reason for packets accumulation are complicated pipelines (e.g.
involving a lot of ACLs).
To prevent packets from being dropped a user can enable PAUSE frames on
the port. This will mark all the active PGs as lossless and set their
size according to the maximum delay, as it's not configured by user.
+----------------+ +
| | |
| | |
| | |
| | |
| | |
| | | Delay
| | |
| | |
| | |
| | |
| | |
Xon/Xoff threshold +----------------+ +
| | |
| | | 2 * MTU
| | |
+----------------+ +
The delay (612 [Cells]) was calculated according to worst-case scenario
involving maximum MTU and 100m cables.
After marking the PGs as lossless the device is configured to respect
incoming PAUSE frames (Rx PAUSE) and generate PAUSE frames (Tx PAUSE)
according to user's settings.
Whenever the port's headroom configuration changes we take into account
the PAUSE configuration, so that we correctly set the PG's type (lossy /
lossless), size and threshold. This can happen when:
a) The port's MTU changes, as it directly affects the PG's size.
b) A PG is created following user configuration, by binding a priority
to it.
Note that the relevant SUPPORTED flags were already mistakenly set by
the driver before this commit.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring PAUSE frames and PFC we'll need to configure the
Xon/Xoff threshold for the priority group (PG) buffers.
Add the Xon/Xoff threshold fields to the PBMC register so that we can
configure these when needed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Port Flow Control Configuration (PFCC) register, which
configures both flow control and Priority-based Flow Control (PFC).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to set maximum rate for a particular TC using DCB ops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the appropriate DCB ops and allow a user to configure:
* Priority to traffic class (TC) mapping with a total of 8
supported TCs
* Transmission selection algorithm (TSA) for each TC and the
corresponding weights in case of weighted round robin (WRR)
As previously explained, we treat the priority group (PG) buffer in the
port's headroom as the ingress counterpart of the egress TC. Therefore,
when a certain priority to TC mapping is configured, we also configure
the port's headroom buffer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic infrastructure for DCB and add the missing ops in
following patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before introducing support for DCB ops we should first make sure we
initialize the relevant parts in the device correctly. Specifically, the
egress scheduling.
The device supports a superset of the 802.1Qaz standard with 4 hierarchy
levels that can be linked to each other in multiple ways and with
different transmission selection algorithms (TSA) employed between them.
However, since we only intend to support the 802.1Qaz standard we
flatten the hierarchies and let the user configure via DCB ops the TSA
and max rate shaper at the subgroup hierarchy (see figure below) and the
mapping between switch priority to traffic class. By default, all switch
priorities are mapped to traffic class 0, strict priority is employed
and max shaper is disabled.
Default configuration:
switch priority 0 ... switch priority 7
+ +
| |
+----------------------------------+
|
+--v--+ +-----+
Traffic Class | | | |
Hierarchy | TC0 | ... | TC7 |
| | | |
+--+--+ +--+--+
| |
+--v--+ +--v--+
Subgroup | SG0 | | SG7 |
Hierarchy | | | |
+-----+ +-----+
| TSA | | TSA |
+-----+ ... +-----+
| MAX | | MAX |
+--+--+ +--+--+
| |
+---------------+----------------+
|
+--v--+
Group | |
Hierarchy | GR0 |
| |
+--+--+
|
+--v--+
Port | |
Hierarchy | PR0 |
| |
+-----+
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of DCB ops we'll have to configure the priority to traffic class
mapping of a port.
Add the QoS Switch Traffic Class Table (QTCT) register, which configures
the mapping between the packet switch priority and traffic class on the
transmit port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to introduce support for DCB, so we need to be able to
configure the traffic selection algorithm (TSA) used by each traffic
class (TC), as well as the bandwidth percentage allocated to each TC in
case of ETS.
Add the QoS ETS Element Configuration register, which controls the
above parameters.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to the priority group (PG) buffers in the headroom, the
device enables the allocation of headroom shared buffer, which can
be shared between different PGs.
However, we are not going to use the headroom shared buffer and instead
allow the user to use its size for PGs or the switch's shared buffer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last field of the PBMC register is at offset 0x64 and its size is
0x8, so the correct register's length is 0x6C bytes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets ingress the switch they are assigned a switch priority and
directed to the corresponding priority group (PG) buffer in the port's
headroom buffer.
Since we now map all switch priorities to priority group 0 (PG0) by
default, there is no need to allocate the other priority groups during
initialization. The only exception is PG9, which is used for control
traffic.
At minimum, the PG should be able to store the currently classified
packet (pipeline latency isn't 0) and also the packets arriving during
the classification time. However, an incoming packet will not be
buffered if there is no available MTU-sized buffer space for storing it.
The buffer needed to accommodate for pipeline latency is variable and
needs to take into account both the current link speed and current
latency of the pipeline, which is time-dependent. Testing showed that
setting the PG's size to twice the current MTU is optimal.
Since PG9 is used strictly for control packets and not subject to flow
control, we are not going to resize it according to user configuration,
so we simply set it according to worst case scenario, which is twice the
maximum MTU.
In any case, later patches in the series will allow a user to direct
lossless flows to other PGs than PG0 and set their size to accommodate
for round-trip propagation delay.
The above change also requires us to resize the PG buffer whenever the
port's MTU is changed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Buffers in the switch store packets in units called buffer cells. Add a
helper to convert from bytes to cells, so that the actual number of
cells required (result is round up) is returned.
Also, drop the SB (shared buffer) acronym from the BYTES_PER_CELL macro,
as this unit is also used in the ports' buffers and not only the
switch's shared buffer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During transmission, the skb's priority is used to map the skb to a
traffic class, where the idea is to group priorities with similar
characteristics (e.g. lossy, lossless) to the same traffic class. By
default, all priorities are mapped to traffic class 0.
In the device, we model the skb's priority as the switch priority, which
is assigned to a packet according to its PCP value and ingress port
(untagged packets are assigned the port's default switch priority - 0).
At ingress, the packet is directed to a priority group (PG) buffer in
the port's headroom buffer according to the packet's switch priority and
switch priority to buffer mapping.
While it's possible to configure the egress mapping between skb's
priority (switch priority) and traffic class, there is no mechanism to
configure the ingress mapping to a PG.
In order to keep things simple and since grouping certain priorities into
a traffic class at egress also implies they should be grouped the same
at ingress, treat a PG as the ingress counterpart of an egress traffic
class.
Having established the above, during initialization map all the switch
priorities to PG0 in accordance with the Linux defaults for traffic
class mapping.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets ingress the switch they are assigned a switch priority
number that dictates the packet's priority group (PG) buffer in the
port's headroom buffer.
Add the Port Prio To Buffer (PPTB) register, which configures the switch
priority to PG mapping.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export to userspace the front panel name of the port, so that udev can
rename the ports accordingly. The convention suggested by switchdev
documentation is used:
1) Non-split: pX
2) Split: pXsY
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resources allocated for these bridges at init time cannot be later used
for other purposes. While current number is supported by the device,
it's mostly theoretical with regards to any real use case, which leads
to poor utilization of device's resources. Solve that by reducing the
number.
The long term plan is to make this value (along with others) user
configurable via devlink and write it to NVRAM, so that it can be used
during the next init. Until then we must hardcode such values.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware now tells us that the reset is done by passing a magic value
via register. Use it to shorten the wait in case this is supported.
With old firmware, we still wait until the timeout is reached.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c62987bbd8 ("bridge: push bridge setting ageing_time down to
switchdev") added a check for minimum and maximum ageing time, but this
breaks existing behaviour where one can set ageing time to 0 for a
non-learning bridge.
Push this check down to the driver and allow the check in the bridge
layer to be removed. Currently ageing time 0 is refused by the driver,
but we can later add support for this functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The descriptor queues for sending (SDQs) and receiving (RDQs) packets
are managed by two counters - producer and consumer - which are both
16-bit in size. A queue is considered full when the difference between
the two equals the queue's maximum number of descriptors.
However, if the producer counter overflows, then it's possible for the
full queue check to fail, as it doesn't take the overflow into account.
In such a case, descriptors already passed to the device - but for which
a completion has yet to be posted - will be overwritten, thereby causing
undefined behavior. The above can be achieved under heavy load (~30
netperf instances).
Fix that by casting the subtraction result to u16, preventing it from
being treated as a signed integer.
Fixes: eda6500a98 ("mlxsw: Add PCI bus implementation")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
