Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
Use WARN_ON() and handle the error cases accordingly.
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This code sequence is unsafe in modules:
static u64 mask = DMA_BIT_MASK(something);
...
if (!dev->dma_mask)
dev->dma_mask = &mask;
as if a module is reloaded, the mask will be pointing at the original
module's mask address, and this can lead to oopses. Moreover, they
all follow this with:
if (!dev->coherent_dma_mask)
dev->coherent_dma_mask = mask;
where 'mask' is the same value as the statically defined mask, and this
bypasses the architecture's check on whether the DMA mask is possible.
Fix these issues by using the new dma_coerce_coherent_and_mask()
function.
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit b0e0a4d ("ASoC: omap: Enable COMPILE_TEST build for DT platforms")
added two incorrect CONFIG_ARCH_ARM dependencies making impossible to select
audio support for Nokia RX-51. Fix this by using correct CONFIG_ARM.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_snd_soc_register_component makes code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=qzif
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.12
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
Remove unneeded error handling on the result of a call to
platform_get_resource_byname when the value is passed to devm_ioremap_resource.
In the case of omap-dmic.c, the error-handling code of
devm_ioremap_resource is also corrected to include releasing the clock.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,e,e1;
expression ret != 0;
identifier l;
@@
res = platform_get_resource_byname(...);
- if (res == NULL) { ... \(goto l;\|return ret;\) }
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the PXA DMA rework, we need the generic dmaengine implementation
that currently lives in sound/soc for standalone (non-ASoC) AC'97
support.
Move it to sound/core, and rename the Kconfig symbol.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just recently OMAP4 legacy boot support has been removed. No reason to keep
the code used by the legacy boot (pdata based) since neither OMAP4 or OMAP5
can boot in this mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add SND_SOC_DAIFMT_CBM_CFS support for omap3/omap4. The patch was tested on
a pandaboard-es board connected to the pcm1792a codec. mcbspx_fsx must
configured as output and mcbspx_clkx must be configured as input.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DT platforms don't have any source dependency on any OMAP stuff so
allow them to be built when COMPILE_TEST is enabled.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The DMA resource no longer available via this API when booting with DT.
When the board is booted with DT do not use platform_get_resource_byname(),
instead set the dma_data.filter_data to the name of the DMA channel and omap-pcm
can use this name to request the DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMA resource no longer available via this API when booting with DT.
DMIC is only available on OMAP4/5 and both can boot with DT only.
Set the dma_data.filter_data to the DMA name which will be used by omap-pcm
to request the DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMA resource no longer available via this API when booting with DT.
McPDM is only available on OMAP4/5 and both can boot with DT only.
Set the dma_data.filter_data to the DMA name which will be used by omap-pcm
to request the DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When booting with DT the platform_get_resource_byname() is not available to
get the DMA resource. In this case the DAI drivers will set the filter_data to
the name of the DMA and omap-pcm can use this to request the DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We still need video & sound drivers with device tree enabled.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace the leftover CONFIG_SND_SOC_OMAP_HDMI_CODEC in
sound/soc/omap/Kconfig with CONFIG_SND_SOC_HDMI_CODEC, which was
forgotten in the commit bf7c6e6c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
to support HDMI on CSR SiRFprimaII and atlasVI, we need one more HDMI pseudo
codec, rather than add a new driver, we can make omap HDMI codec common for
other SoCs as well. then the omap-hdmi codec becomes a generic HDMI pseudo-
codec as HDMI audio features depend on HDMI specification not on SoCs.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support for omap2evm was removed in v3.0. But only one of its two
lines in this Makefile was removed. Remove the second line too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MXrq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More updates for v3.10
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
Refactor the dmaengine PCM library to allow the DMA channel to be requested
before opening a PCM substream. snd_dmaengine_pcm_open() now expects a DMA
channel instead of a filter function and filter parameter as its parameters.
snd_dmaengine_pcm_close() is updated to not release the DMA channel. This allows
a dmaengine based PCM driver to request its channels before the substream is
opened.
The patch also introduces two new functions, snd_dmaengine_pcm_open_request_chan()
and snd_dmaengine_pcm_close_release_chan(), which have the same signature and
behaviour of the old snd_dmaengine_pcm_{open,close}() and internally use the new
variants of these functions. All users of snd_dmaengine_pcm_{open,close}() are
updated to use snd_dmaengine_pcm_open_request_chan() and
snd_dmaengine_pcm_close_release_chan().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the common DAI DMA data struct for omap, this allows us to use the common
helper function to configure the DMA slave config based on the DAI DMA data.
For omap-dmic and omap-mcpdm also move the DMA data from a global variable to
the driver state struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a PCM driver using the dmaengine PCM helper functions doesn't need to do
anything special in its pcm_close callback, snd_dmaengine_pcm_close can be used
directly for as the pcm_close callback and there is no need to wrap it in a
custom function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The omap PCM driver provides a set_threshold callback which gets called by the
PCM driver when either playback or capture is started. The only DAI driver which
sets this callback is the mcbsp driver. This patch removes the callback from the
PCM driver and moves the invocation of the omap_mcbsp_set_threshold() function
to the mcbsp hw_params callback since this is the only place where the threshold
size can change. Doing so allows us to use the default dmaengine PCM trigger
callback in the omap PCM driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The IO address is no longer hardwired into the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to HW limitation within OMAP McPDM IP uplink and downlink need to be
started at the same time. This causes issues when we have two streams
running, for example:
arecord | aplay
In this case the playback stream would have no channels enabled since at the
capture start we are not aware that a playback is going to start.
The workaround is to configure the other direction to stereo when the first
stream is started. When the second stream is coming we check the new stream's
number of channels against the pre-configured channels. If it does not match
we stop and restart McPDM to update the configuration. This might result a
small pop. If the coming stream is a match we do nothing in the McPDM driver.
This workaround can handle most use cases without the need to restart McPDM.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mcpdm_link_config will collect the link direction related configurations like
channel masks, FIFO threshold.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes:
sound/soc/omap/omap3pandora.c: In function ‘omap3pandora_dac_event’:
sound/soc/omap/omap3pandora.c:92:19: error: request for member ‘dev’ in something not a structure or union
make[3]: *** [sound/soc/omap/omap3pandora.o] Error 1
Which is introduced by:
dd194b4 ASoC: omap: Check regulator enable for DAC on Pandora
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will probably never fail but it's better style.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Clean up dmic code with devm_request_and_ioremap function.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Clean up McPDM driver with devm_ function.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove unused memory ressource get from McPDM driver.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
