The main goal of the change is to remove .pin_config_dbg_parse_modify
callback before a driver with its support appears. So far the in-kernel
interface did not attract any users since its introduction 5 years ago.
Originally .pin_config_dbg_parse_modify callback and the associated
'pinconf-config' debugfs file were introduced in commit f07512e615
("pinctrl/pinconfig: add debug interface"), a short description of
'pinconf-config' usage for debugging can be expressed this way:
Write to 'pinconf-config' (see pinconf_dbg_config_write() function):
% echo -n modify $map_type $device_name $state_name $pin_name $config > \
/sys/kernel/debug/pinctrl/$pinctrl/pinconf-config
It supposes to update a global (therefore single!) 'pinconf_dbg_conf'
variable with an alternative setting, the arguments should match
an existing pinconf device and some registered pinctrl mapping 'map':
* $map_type is either 'config_pin' or 'config_group', it should match
'map->type' value of PIN_MAP_TYPE_CONFIGS_PIN or
PIN_MAP_TYPE_CONFIGS_GROUP accordingly,
* $device_name should match 'map->dev_name' string value,
* $state_name should match 'map->name' string value,
* $pin_name should match 'map->data.configs.group_or_pin' string value,
If all above has matched, then $config is a new value to be set by calling
pinconfops->pin_config_dbg_parse_modify(pctldev, config, matched_config).
After a successful write into 'pinconf-config' a user can read the file
to get information about that single modified pin configuration.
The fact is .pin_config_dbg_parse_modify callback has never been defined
in 'struct pinconf_ops' of any pinconf driver, thus an actual modification
of a pin or group state on any present pinconf controller does not happen,
and it declares that all related code is no more than dead code.
I discovered the issue while attempting to add .pin_config_dbg_parse_modify
support in some drivers and found that too short 'MAX_NAME_LEN' set by
drivers/pinctrl/pinconf.c:372:#define MAX_NAME_LEN 15
is practically insufficient to store a regular pinctrl device name,
which are like 'e6060000.pin-controller-sh-pfc' or pin names like
'MX6QDL_PAD_ENET_REF_CLK', thus it is another indicator that the code
is barely usable, insufficiently tested and unprepossessing.
Of course it might be possible to increase MAX_NAME_LEN, and then add
.pin_config_dbg_parse_modify callbacks to the drivers, but the whole
idea of such a limited debug option looks inviable. A more flexible
way to functionally substitute the original approach is to implicitly
or explicitly use pinctrl_select_state() function whenever needed.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Laurent Meunier <laurent.meunier@st.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change adds explicit inclusion of linux/pinctrl/machine.h header
to the only needed pinctrl-madera-core.c file, and therefore inclusion
of pinctrl/machine.h header from pinctrl/pinconf.h can be removed.
The change is preparatory to a follow-up reversal of commit f07512e615
("pinctrl/pinconfig: add debug interface").
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinconf_generic_dump_one() function makes the assumption that
pin_config_group_get() should return -EINVAL and -ENOTSUPP just like
pin_config_get() does. Document that so it's more obvious.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When pulling the recent pinctrl merge, I was surprised by how a
pinctrl-only pull request ended up rebuilding basically the whole
kernel.
The reason for that ended up being that <linux/device.h> included
<linux/pinctrl/devinfo.h>, so any change to that file ended up causing
pretty much every driver out there to be rebuilt.
The reason for that was because 'struct device' has this in it:
#ifdef CONFIG_PINCTRL
struct dev_pin_info *pins;
#endif
but we already avoid header includes for these kinds of things in that
header file, preferring to just use a forward-declaration of the
structure instead. Exactly to avoid this kind of header dependency.
Since some drivers seem to expect that <linux/pinctrl/devinfo.h> header
to come in automatically, move the include to <linux/pinctrl/pinctrl.h>
instead. It might be better to just make the includes more targeted,
but I'm not going to review every driver.
It would definitely be good to have a tool for finding and minimizing
header dependencies automatically - or at least help with them. Right
now we almost certainly end up having way too many of these things, and
it's hard to test every single configuration.
FWIW, you can get a sense of the "hotness" of a header file with something
like this after doing a full build:
find . -name '.*.o.cmd' -print0 |
xargs -0 tail --lines=+2 |
grep -v 'wildcard ' |
tr ' \\' '\n' |
sort | uniq -c | sort -n | less -S
which isn't exact (there are other things in those '*.o.cmd' than just
the dependencies, and the "--lines=+2" only removes the header), but
might a useful approximation.
With this patch, <linux/pinctrl/devinfo.h> drops to "only" having 833
users in the current x86-64 allmodconfig. In contrast, <linux/device.h>
has 14857 build files including it directly or indirectly.
Of course, the headers that absolutely _everybody_ includes (things like
<linux/types.h> etc) get a score of 23000+.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core changes:
- After lengthy discussions and partly due to my ignorance, we have
merged a patch making pinctrl_force_default() and pinctrl_force_sleep()
reprogram the states into the hardware of any hogged pins, even
if they are already in the desired state. This only apply to hogged
pins since groups of pins owned by drivers need to be managed by
each driver, lest they could not do things like runtime PM and
put pins to sleeping state even if the system as a whole is not
in sleep.
New drivers:
- New driver for the Microsemi Ocelot SoC. This is used in ethernet
switches.
- The X-Powers AXP209 GPIO driver was extended to also deal with pin
control and moved over from the GPIO subsystem. This circuit is
a mixed-mode integrated circuit which is part of AllWinner designs.
- New subdriver for the Qualcomm MSM8998 SoC, core of a high end
mobile devices (phones) chipset.
- New subdriver for the ST Microelectronics STM32MP157 MPU and
STM32F769 MCU from the STM32 family.
- New subdriver for the MediaTek MT7622 SoC. This is used for routers,
repeater, gateways and such network infrastructure.
- New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC has
multimedia features and target "smart devices", I guess in-car
entertainment, in-flight entertainment, industrial control panels etc.
General improvements:
- Incremental improvements on the SH-PFC subdrivers for things like
the CAN bus.
- Enable the glitch filter on Baytrail GPIOs used for interrupts.
- Proper handling of pins to GPIO ranges on the Semtec SX150X
- An IRQ setup ordering fix on MCP23S08.
- A good set of janitorial coding style fixes.
-----BEGIN PGP SIGNATURE-----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=gLY/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.16 kernel cycle.
Like with GPIO it is actually a bit calm this time.
Core changes:
- After lengthy discussions and partly due to my ignorance, we have
merged a patch making pinctrl_force_default() and
pinctrl_force_sleep() reprogram the states into the hardware of any
hogged pins, even if they are already in the desired state.
This only apply to hogged pins since groups of pins owned by
drivers need to be managed by each driver, lest they could not do
things like runtime PM and put pins to sleeping state even if the
system as a whole is not in sleep.
New drivers:
- New driver for the Microsemi Ocelot SoC. This is used in ethernet
switches.
- The X-Powers AXP209 GPIO driver was extended to also deal with pin
control and moved over from the GPIO subsystem. This circuit is a
mixed-mode integrated circuit which is part of AllWinner designs.
- New subdriver for the Qualcomm MSM8998 SoC, core of a high end
mobile devices (phones) chipset.
- New subdriver for the ST Microelectronics STM32MP157 MPU and
STM32F769 MCU from the STM32 family.
- New subdriver for the MediaTek MT7622 SoC. This is used for
routers, repeater, gateways and such network infrastructure.
- New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC
has multimedia features and target "smart devices", I guess in-car
entertainment, in-flight entertainment, industrial control panels
etc.
General improvements:
- Incremental improvements on the SH-PFC subdrivers for things like
the CAN bus.
- Enable the glitch filter on Baytrail GPIOs used for interrupts.
- Proper handling of pins to GPIO ranges on the Semtec SX150X
- An IRQ setup ordering fix on MCP23S08.
- A good set of janitorial coding style fixes"
* tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (102 commits)
pinctrl: mcp23s08: fix irq setup order
pinctrl: Forward declare struct device
pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
pinctrl: stm32: add STM32F769 MCU support
pinctrl: sx150x: Add a static gpio/pinctrl pin range mapping
pinctrl: sx150x: Register pinctrl before adding the gpiochip
pinctrl: sx150x: Unregister the pinctrl on release
pinctrl: ingenic: Remove redundant dev_err call in ingenic_pinctrl_probe()
pinctrl: sprd: Use seq_putc() in sprd_pinconf_group_dbg_show()
pinctrl: pinmux: Use seq_putc() in pinmux_pins_show()
pinctrl: abx500: Use seq_putc() in abx500_gpio_dbg_show()
pinctrl: mediatek: mt7622: align error handling of mtk_hw_get_value call
pinctrl: mediatek: mt7622: fix potential uninitialized value being returned
pinctrl: uniphier: refactor drive strength get/set functions
pinctrl: imx7ulp: constify struct imx_cfg_params_decode
pinctrl: imx: constify struct imx_pinctrl_soc_info
pinctrl: imx7d: simplify imx7d_pinctrl_probe
pinctrl: imx: use struct imx_pinctrl_soc_info as a const
pinctrl: sunxi-pinctrl: fix pin funtion can not be match correctly.
pinctrl: qcom: Add msm8998 pinctrl driver
...
pinctrl/devinfo.h is using forward declaration from pinctrl/consumer.h
for configurations with CONFIG_PINCTRL defined, however nothing declares
it in the opposite case. Fix this by adding a forward declaration.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
General support for state persistence is added to gpiolib with the
introduction of a new pinconf parameter to propagate the request to
hardware. The existing persistence support for sleep is adapted to
include hardware support if the GPIO driver provides it. Persistence
continues to be enabled by default; in-kernel consumers can opt out, but
userspace (currently) does not have a choice.
The *_SLEEP_MAY_LOSE_VALUE and *_SLEEP_MAINTAIN_VALUE symbols are
renamed, dropping the SLEEP prefix to reflect that the concept is no
longer sleep-specific. I feel that renaming to just *_MAY_LOSE_VALUE
could initially be misinterpreted, so I've further changed the symbols
to *_TRANSITORY and *_PERSISTENT to address this.
The sysfs interface is modified only to keep consistency with the
chardev interface in enforcing persistence for userspace exports.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into
a menuconfig option. This obviously has the implication of
making the subsystem menu visible in menuconfig. This is
happening because of two things:
- Intel have started to deploy and depend on pin controllers
in a way that is affecting users directly. This happens
on the highly integrated laptop chipsets named after
geographical places: baytrail, broxton, cannonlake,
cedarfork, cherryview, denverton, geminilake, lewisburg,
merrifield, sunrisepoint... It started a while back and
now it is ever more evident that this is crucial
infrastructure for x86 laptops and not an embedded
obscurity anymore. Users need to be aware.
- Pin control expanders on I2C and SPI that are
arch-agnostic. Currently Semtech SX150X and Microchip
MCP28x08 but more are expected. Users will have to be
able to configure these in directly for their set-up.
- Just go and select GPIOLIB now that we made sure that
GPIOLIB is a very vanilla subsystem. Do not depend on
it, if we need it, select it.
- Exposing the pin control subsystem in menuconfig uncovered
a bunch of obscure bugs that are now hopefully fixed,
all more or less pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and
GPIO.
- New support for clock skew/delay generic DT bindings
and generic pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying.
-----BEGIN PGP SIGNATURE-----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=kj/b
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
Some pin controllers (such as the Gemini) can control the
expected clock skew and output delay on certain pins with a
sub-nanosecond granularity. This is typically done by shunting
in a number of double inverters in front of or behind the pin.
Make it possible to configure this with a generic binding.
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In some scenarios, we should set some pins as input/output/pullup/pulldown
when the specified system goes into deep sleep mode, then when the system
goes into deep sleep mode, these pins will be set automatically by hardware.
That means some pins are not controlled by any specific driver in the OS, but
need to be controlled when entering sleep mode. Thus we introduce one sleep
state config into pinconf-generic for users to configure.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update deprecated references to Documentation/pinctrl.txt since it has been
moved to Documentation/driver-api/pinctl.rst.
Signed-off-by: Ludovic Desroches <ludovic.desroches@o2linux.fr>
Fixes: 5a9b73832e ("pinctrl.txt: move it to the driver-api book")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add output-enable generic pin configuration property.
This properties allows enabling/disabling pin's output capabilities
without actually driving any value on the line.
Acked-by: Rob Herring <robh@kernel.org>
[Added inline elaborations on buffer enabling/disabling]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 8c58f1a7a4.
It turns out that applying these generic properties was
premature: the properties used in the driver using this
are of unclear electrical nature and the subject need to
be discussed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add bi-directional and output-enable pin configurations to
the generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- A whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- Switch meson driver to get the GPIO ranges from the device
tree.
- Input schmitt trigger support on the Rockchip driver.
- Enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- Name the Qualcomm QDF2xxx GPIO lines.
- Support GMMR GPIO regions on the Intel Cherryview. This
fixes a serialization problem on these platforms.
- Pad retention support for the Samsung Exynos 5433.
- Handle suspend-to-ram in the AT91-pio4 driver.
- Pin configuration support in the Aspeed driver.
Cleanups:
- The final name of Rockchip RK1108 was RV1108 so rename the
driver and variables to stay consistent.
-----BEGIN PGP SIGNATURE-----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=BCaA
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.12 cycle.
The extra week before the merge window actually resulted in some of
the type of fixes that usually arrive after the merge window already
starting to trickle in from eager developers using -next, I'm
impressed.
I have recruited a Samsung subsubsystem maintainer (Krzysztof) to deal
with the onset of Samsung patches. It works great.
Apart from that it is a boring round, just incremental updates and
fixes all over the place, no serious core changes or anything exciting
like that. The most pleasing to see is Julia Cartwrights work to audit
the irqchip-providing drivers for realtime locking compliance. It's
one of those "I should really get around to looking into that" things
that have been on my TODO list since forever.
Summary:
Core changes:
- add bi-directional and output-enable pin configurations to the
generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- a whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- switch meson driver to get the GPIO ranges from the device tree.
- input schmitt trigger support on the Rockchip driver.
- enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- name the Qualcomm QDF2xxx GPIO lines.
- support GMMR GPIO regions on the Intel Cherryview. This fixes a
serialization problem on these platforms.
- pad retention support for the Samsung Exynos 5433.
- handle suspend-to-ram in the AT91-pio4 driver.
- pin configuration support in the Aspeed driver.
Cleanups:
- the final name of Rockchip RK1108 was RV1108 so rename the driver
and variables to stay consistent"
* tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl: mediatek: Add missing pinctrl bindings for mt7623
pinctrl: artpec6: Fix return value check in artpec6_pmx_probe()
pinctrl: artpec6: Remove .owner field for driver
pinctrl: tegra: xusb: Silence sparse warnings
ARM: at91/at91-pinctrl documentation: fix spelling mistake: "contoller" -> "controller"
pinctrl: make artpec6 explicitly non-modular
pinctrl: aspeed: g5: Add pinconf support
pinctrl: aspeed: g4: Add pinconf support
pinctrl: aspeed: Add core pinconf support
pinctrl: aspeed: Document pinconf in devicetree bindings
pinctrl: Add st,stm32f469-pinctrl compatible to stm32-pinctrl
pinctrl: stm32: Add STM32F469 MCU support
Documentation: dt: Remove ngpios from stm32-pinctrl binding
pinctrl: stm32: replace device_initcall() with arch_initcall()
pinctrl: stm32: add possibility to use gpio-ranges to declare bank range
pinctrl: armada-37xx: Add gpio support
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
pinctrl: core: Make pinctrl_init_controller() static
pinctrl: generic: Add bi-directional and output-enable
...
Add bi-directional and output-enable pin configuration properties.
bi-directional allows to specify when a pin shall operate in input and
output mode at the same time. This is particularly useful in platforms
where input and output buffers have to be manually enabled.
output-enable is just syntactic sugar to specify that a pin shall
operate in output mode, ignoring the provided argument.
This pairs with input-enable pin configuration option.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Recent pinctrl changes to allow dynamic allocation of pins exposed one
more issue with the pinctrl pins claimed early by the controller itself.
This caused a regression for IMX6 pinctrl hogs.
Before enabling the pin controller driver we need to wait until it has
been properly initialized, then claim the hogs, and only then enable it.
To fix the regression, split the code into pinctrl_claim_hogs() and
pinctrl_enable(). And then let's require that pinctrl_enable() is always
called by the pin controller driver when ready after calling
pinctrl_register_and_init().
Depends-on: 950b0d91dc ("pinctrl: core: Fix regression caused by delayed
work for hogs")
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Fixes: e566fc11ea ("pinctrl: imx: use generic pinctrl helpers for
managing groups")
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a GPIO driver is backed by a pinctrl driver the GPIO driver
sometimes needs to call the pinctrl driver to configure certain things,
like whether the pin is used as input or output. In addition to this
there are other configurations applicable to GPIOs such as setting
debounce time of the GPIO.
To support this we introduce a new function pinctrl_gpio_set_config()
that can be used by gpiolib based driver to pass configuration requests
to the backing pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.
In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.
We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit df61b366af26 ("pinctrl: core: Use delayed work for hogs") caused a
regression at least with sh-pfc that is also a GPIO controller as
noted by Geert Uytterhoeven <geert@linux-m68k.org>.
As the original pinctrl_register() has issues calling pin controller
driver functions early before the controller has finished registering,
we can't just revert commit df61b366af26. That would break the drivers
using GENERIC_PINCTRL_GROUPS or GENERIC_PINMUX_FUNCTIONS.
So let's fix the issue with the following steps as a single patch:
1. Revert the late_init parts of commit df61b366af26.
The late_init clearly won't work and we have to just give up
on fixing pinctrl_register() for GENERIC_PINCTRL_GROUPS and
GENERIC_PINMUX_FUNCTIONS.
2. Split pinctrl_register() into two parts
By splitting pinctrl_register() into pinctrl_init_controller()
and pinctrl_create_and_start() we have better control over when
it's safe to call pinctrl_create().
3. Introduce a new pinctrl_register_and_init() function
As suggested by Linus Walleij <linus.walleij@linaro.org>, we
can just introduce a new function for the controllers that need
pinctrl_create() called later.
4. Convert the four known problem cases to use new function
Let's convert pinctrl-imx, pinctrl-single, sh-pfc and ti-iodelay
to use the new function to fix the issues. The rest of the drivers
can be converted later. Let's also update Documentation/pinctrl.txt
accordingly because of the known issues with pinctrl_register().
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinconf-generic.h file exposes functions for creating generic mappings
but it does not expose a function for freeing the mappings. Add a function
for freeing generic mappings.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add device managed APIs devm_pinctrl_register() and
devm_pinctrl_unregister() for the APIs pinctrl_register()
and pinctrl_unregister().
This helps in reducing code in error path and sometimes
removal of .remove callback for driver unbind.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For pinctrl the "default" state is applied to pins before the driver's
probe function is called. This is normally a sensible thing to do,
but in some cases can cause problems. That's because the pins will
change state before the driver is given a chance to program how those
pins should behave.
As an example you might have a regulator that is controlled by a PWM
(output high = high voltage, output low = low voltage). The firmware
might leave this pin as driven high. If we allow the driver core to
reconfigure this pin as a PWM pin before the PWM's probe function runs
then you might end up running at too low of a voltage while we probe.
Let's introudce a new "init" state. If this is defined we'll set
pinctrl to this state before probe and then "default" after probe
(unless the driver explicitly changed states already).
An alternative idea that was thought of was to use the pre-existing
"sleep" or "idle" states and add a boolean property that we should
start in that mode. This was not done because the "init" state is
needed for correctness and those other states are only present (and
only transitioned in to and out of) when (optional) power management
is enabled.
Changes in v3:
- Moved declarations to pinctrl/devinfo.h
- Fixed author/SoB
Changes in v2:
- Added comment to pinctrl_init_done() as per Linus W.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the dt_params array in drivers/pinctrl/pinconf-generic.c
is not sorted in the same order as the enum pin_config_param in
include/linux/pinctrl/pinconf-generic.h.
Sort enum pin_config_param, conf_items, dt_params, alphabetically
for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Only this member, pins, is defined as "struct ... const *", but the
others in this struct, pinlops, pmxops, confops, etc. are defined as
"const struct ... *".
Swap the "struct pinctrl_pin_desc" and "const" for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This "const" claims the get_function_groups callback never
changes the given num_groups pointer. It is always true
in C language, so not worth mentioning.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While the pinmux_ops are ideally just a vtable for pin mux
calls, the "strict" setting belongs so intuitively with the
pin multiplexing that we should move it here anyway. Putting
it in the top pinctrl_desc makes no sense.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Disallow simultaneous use of the the GPIO and peripheral mux
functions by setting a flag "strict" in struct pinctrl_desc.
The blackfin pinmux and gpio controller doesn't allow user to
set up a pin for both GPIO and peripheral function. So, add flag
strict in struct pinctrl_desc to check both gpio_owner and
mux_owner before approving the pin request.
v2-changes:
- if strict flag is set, check gpio_owner and mux_onwer in if and
else clause
v3-changes:
- add kerneldoc for this struct
- augment Documentation/pinctrl.txt
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 5a7d2efdd9.
As per discussion on the mailing list, this is not the right
thing to do. NULL cookies are valid in the stubs.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These functions are supposed to return an error pointer, not NULL.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New pin controllers such as ACPI-based may also have custom properties
to parse, and should be able to use generic pin config. Let's make the
code compile on !OF systems and rename members a bit to underscore it
is custom parameters and not necessarily DT parameters.
This fixes a build regression for x86_64 on the zeroday kernel builds.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-and-tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Additionally to the generic DT parameters, allow drivers to provide
driver-specific DT parameters to be used with the generic parser
infrastructure.
To achieve this 'struct pinctrl_desc' is extended to pass custom pinconf
option to the core. In order to pass this kind of information, the
related data structures - 'struct pinconf_generic_dt_params',
'pin_config_item' - are moved from pinconf internals to the
pinconf-generic header.
Additionally pinconfg-generic is refactored to not only iterate over the
generic pinconf parameters but also take the parameters into account
that are provided through the driver's 'struct pinctrl_desc'.
In particular 'pinconf_generic_parse_dt_config()' and
'pinconf_generic_dump' helpers are split into two parts each. In order
to have a more generic helper that can be used to process the generic
parameters as well as the driver-specific ones.
v2:
- fix typo
- add missing documentation for @conf_items member in struct
- rebase to pinctrl/devel: conflict in abx500
- rename _pinconf_generic_dump() to pinconf_generic_dump_one()
- removed '_' from _parse_dt_cfg()
- removed BUG_ONs, error condition is handled in if statements
- removed pinconf_generic_dump_group() & pinconf_generic_dump_pin
helpers
- fixed up corresponding call sites
- renamed pinconf_generic_dump() to pinconf_generic_dump_pins()
- added kernel-doc to pinconf_generic_dump_pins()
- add kernel-doc
- more verbose commit message
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the new 'groups' property, the DT parser can infer the map type
from the fact whether 'pins' or 'groups' is used to specify the pin
group to work on.
To maintain backwards compatibitliy with current usage of the DT
binding, this is only done when PIN_MAP_TYPE_INVALID is passed to the
parsing function as type.
Also, a new helper 'pinconf_generic_dt_node_to_map_all()' is introduced,
which can be used by drivers as generic callback for dt_node_to_map() to
leverage the new feature.
Changes since v2:
- rename dt_pin_specifier to subnode_target_type
- add additional comment in header file explaining passing an invalid
map type
- mention map_all() helper in commit message
Changes since RFC v2:
- none
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PIN_CONFIG_DRIVE_OPEN_SOURCE enables open source, not open drain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 2243a87d90
"pinctrl: avoid duplicated calling enable_pinmux_setting for a pin"
removed the .disable callback from the struct pinmux_ops,
making the .enable() callback the only remaining callback.
However .enable() is a bad name as it seems to imply that a
muxing can also be disabled. Rename the callback to .set_mux()
and also take this opportunity to clean out any remaining
mentions of .disable() from the documentation.
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Fan Wu <fwu@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
What the patch does:
1. Call pinmux_disable_setting ahead of pinmux_enable_setting
each time pinctrl_select_state is called
2. Remove the HW disable operation in pinmux_disable_setting function.
3. Remove the disable ops in struct pinmux_ops
4. Remove all the disable ops users in current code base.
Notes:
1. Great thanks for the suggestion from Linus, Tony Lindgren and
Stephen Warren and Everyone that shared comments on this patch.
2. The patch also includes comment fixes from Stephen Warren.
The reason why we do this:
1. To avoid duplicated calling of the enable_setting operation
without disabling operation inbetween which will let the pin
descriptor desc->mux_usecount increase monotonously.
2. The HW pin disable operation is not useful for any of the
existing platforms.
And this can be used to avoid the HW glitch after using the
item #1 modification.
In the following case, the issue can be reproduced:
1. There is a driver that need to switch pin state dynamically,
e.g. between "sleep" and "default" state
2. The pin setting configuration in a DTS node may be like this:
component a {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&a_grp_setting &c_grp_setting>;
pinctrl-1 = <&b_grp_setting &c_grp_setting>;
}
The "c_grp_setting" config node is totally identical, maybe like
following one:
c_grp_setting: c_grp_setting {
pinctrl-single,pins = <GPIO48 AF6>;
}
3. When switching the pin state in the following official pinctrl
sequence:
pin = pinctrl_get();
state = pinctrl_lookup_state(wanted_state);
pinctrl_select_state(state);
pinctrl_put();
Test Result:
1. The switch is completed as expected, that is: the device's
pin configuration is changed according to the description in the
"wanted_state" group setting
2. The "desc->mux_usecount" of the corresponding pins in "c_group"
is increased without being decreased, because the "desc" is for
each physical pin while the setting is for each setting node
in the DTS.
Thus, if the "c_grp_setting" in pinctrl-0 is not disabled ahead
of enabling "c_grp_setting" in pinctrl-1, the desc->mux_usecount
will keep increasing without any chance to be decreased.
According to the comments in the original code, only the setting,
in old state but not in new state, will be "disabled" (calling
pinmux_disable_setting), which is correct logic but not intact. We
still need consider case that the setting is in both old state
and new state. We can do this in the following two ways:
1. Avoid to "enable"(calling pinmux_enable_setting) the "same pin
setting" repeatedly
2. "Disable"(calling pinmux_disable_setting) the "same pin setting",
actually two setting instances, ahead of enabling them.
Analysis:
1. The solution #2 is better because it can avoid too much
iteration.
2. If we disable all of the settings in the old state and one of
the setting(s) exist in the new state, the pins mux function
change may happen when some SoC vendors defined the
"pinctrl-single,function-off"
in their DTS file.
old_setting => disabled_setting => new_setting.
3. In the pinmux framework, when a pin state is switched, the
setting in the old state should be marked as "disabled".
Conclusion:
1. To Remove the HW disabling operation to above the glitch mentioned
above.
2. Handle the issue mentioned above by disabling all of the settings
in old state and then enable the all of the settings in new state.
Signed-off-by: Fan Wu <fwu@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drv_data is added to the pinctrl_pin_desc for drivers to define additional
driver-specific per-pin data.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PIN_CONFIG_OUTPUT parameter is really tricky to understand
and needs an explicit pointer to the documentation.
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the infrastructure required to register non-linear gpio
ranges through gpiolib and the standard GPIO device tree bindings.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When setting pin configuration in the pinctrl framework, pin_config_set() or
pin_config_group_set() is called in a loop to set one configuration at a time
for the specified pin or group.
This patch 1) removes the loop and 2) changes the API to pass the whole pin
config array to the driver. It is now up to the driver to loop through the
configs. This allows the driver to potentially combine configs and reduce the
number of writes to pin config registers.
All c files changed have been build-tested to verify the change compiles and
that the corresponding .o is successfully generated.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support to pass the config type like GROUP or PIN when using
the utils or generic pin configuration APIs. This will make the
APIs more generic.
Added additional inline APIs such that it can be use directly as
callback for the pinctrl_ops.
Changes from V1:
- Remove separate implementation for pins and group for
pinctrl_utils_dt_free_map and improve this function
to support both i.e. PINS and GROUPs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit e81c8f18af
"pinctrl: pinconf-generic: add generic APIs for mapping pinctrl node"
Added function prototypes with implicit dependencies
on other header files causing build warnings like this:
In file included from
arch/arm/mach-ux500/board-mop500-pins.c:12:0:
include/linux/pinctrl/pinconf-generic.h:142:3:
warning: 'struct device_node' declared inside parameter list [enabled
by default]
unsigned *reserved_maps, unsigned *num_maps);
^
include/linux/pinctrl/pinconf-generic.h:142:3:
warning: its scope is only this definition or declaration, which is
probably not what you want [enabled by default]
include/linux/pinctrl/pinconf-generic.h:142:3:
warning: 'struct pinctrl_dev' declared inside parameter list [enabled
by default]
include/linux/pinctrl/pinconf-generic.h:145:3:
warning: 'struct device_node' declared inside parameter list [enabled
by default]
unsigned *num_maps);
^
Let's just add ifdefs for non-DT systems (the actual code is
already ifdefed) and #include <linux/device.h> to get the
most important structs and forward-declare the pinctrl
core structs.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add generic APIs to map the DT node and its sub node in pinconf generic
driver. These APIs can be used from driver to parse the DT node who
uses the pinconf generic APIs for defining their nodes.
Changes from V1:
- Add generic property for pins and functions in pinconf-generic.
- Add APIs to map the DT and subnode.
- Move common utils APIs to the pinctrl-utils from this file.
- Update the binding document accordingly.
Changes from V2:
- Rebased the pinctrl binding doc on top of Stephen's cleanup.
- Rename properties "pinctrl-pins" and "pinctrl-function" to
"pins" and "function".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the debounce time pinconfig option uses an unspecified
"time units" unit. As pinconfig options should use SI units and a
real unit is also necessary for generic dt bindings, change it
to usec. Currently no driver is using the generic pinconfig option
for this, so the unit change is safe to do.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
