Previously, delta filtering was applied TSC co-ordinate readouts before
reporting a single value to user space. This patch replaces delta filtering
with median filtering. Median filtering sorts co-ordinate readouts, drops
min and max values, and reports the average of remaining values. This
method is more sensible than delta filtering. Median filtering is applied
only if number of readouts is greater than 3 else just average of
co-ordinate readouts is reported.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch reads charge delay from tsc DT node and writes to
REG_CHARGEDELAY register. If the charge delay is not specified in DT then
default value of 0x400(CHARGEDLY_OPENDLY) is used.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
TSC interrupt handler had udelay to avoid reporting of false pen-up
interrupt to user space. This patch implements workaround suggesting in
Advisory 1.0.31 of silicon errata for am335x, thus eliminating udelay and
touchscreen lag. This also improves performance of touchscreen and
eliminates sudden jump of cursor at touch release.
IDLECONFIG and CHARGECONFIG registers are to be configured with same values
in order to eliminate false pen-up events. This workaround may result in
false pen-down to be detected, hence considerable charge step delay needs
to be added. The charge delay is set to 0xB000 (in terms of ADC clock
cycles) by default.
TSC steps are disabled at the end of every sampling cycle and EOS bit is
set. Once the EOS bit is set, the TSC steps need to be re-enabled to begin
next sampling cycle.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.19rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch makes the initial changes required to workaround TSC-false
pen-up interrupts. It is required to implement these changes in order to
remove udelay in the TSC interrupt handler and false pen-up events. The
charge step is to be executed immediately after sampling X+. Hence TSC is
made to use higher numbered steps (steps 5 to 16 for 5 co-ordinate
readouts, 4 wire TSC configuration) and ADC to use lower ones. Further X
co-ordinate readouts must be the last to be sampled, thus co-ordinates are
sampled in the order Y-Z-X.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.19rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices are not fast enough to differentiate between a fast-moving
contact and a new contact. This problem cannot be fully resolved because
information is truly missing, but it is possible to safe-guard against
obvious mistakes by restricting movement with a maximum displacement.
The new problem formulation for dmax > 0 cannot benefit from the speedup
for positive definite matrices, but since the convergence is faster, the
result is about the same. For a handful of contacts, the latency difference
is truly negligible.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Allwinner A31 SoC (sun6i) has the same resistive touchpanel controller
as on other sunxi platforms. The only difference between the variants is
the control bits for enabling operations are left-shifted by 1 on the A31.
Also update the comment for the original temperature sensor with
information from Allwinner.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen controller has a temperature sensor embedded in the SoC,
which already has hwmon support in the driver.
Add DT thermal zone support so we can use it with cpufreq for thermal
throttling.
This also adds a comment stating that we do not know the actual formula
for calculating the temperature.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUsuDQAAoJEHm+PkMAQRiGnecH/0RO9UKnEduOTRPaZGXAjGI8
N0FvNia8qn7f+XnvN62pG/YZZqi2uvuy37vwAXMtS6KXEgaDG9Wq4fVrhOaJ5VgL
QOmPdVGUa+1PuPcMYj/QLIFRfIHvIY/XVZWXrcIyYfQdBAAoJ2q23qx/yFmdyTwf
+enAv+PV4ZVNMEANyN9KS7xX5gPbSDl36AOhm6lXDvrlem4mbnhRuUtYez9R8KTK
VNfkKZQRDOgl4/ns0ndzpAUhaDj1JJGoLRgMXKna33XgtzSEL4XijvImdnoIXp5N
Z98Jc1N5Vg5OcUFeGJC3bRR27m39xoOHQk2ufY43uAIfB3Ez/C7m/r7b50ZVWfs=
=J7TO
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rc4' into next
Merge with mainline to bring in the latest thermal and other changes.
Pull input layer fixes from Dmitry Torokhov:
"Fixes for v7 protocol for ALPS devices and few other driver fixes.
Also users can request input events to be stamped with boot time
timestamps, in addition to real and monotonic timestamps"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: hil_kbd - fix incorrect use of init_completion
Input: alps - v7: document the v7 touchpad packet protocol
Input: alps - v7: fix finger counting for > 2 fingers on clickpads
Input: alps - v7: sometimes a single touch is reported in mt[1]
Input: alps - v7: ignore new packets
Input: evdev - add CLOCK_BOOTTIME support
Input: psmouse - expose drift duration for IBM trackpoints
Input: stmpe - bias keypad columns properly
Input: stmpe - enforce device tree only mode
mfd: stmpe: add pull up/down register offsets for STMPE
Input: optimize events_per_packet count calculation
Input: edt-ft5x06 - fixed a macro coding style issue
Input: gpio_keys - replace timer and workqueue with delayed workqueue
Input: gpio_keys - allow separating gpio and irq in device tree
Pull input subsystem updates from Dmitry Torokhov:
"Two new drivers for Elan hardware (for I2C touchpad and touchscreen
found in several Chromebooks and other devices), a driver for Goodix
touch panel, and small fixes to Cypress I2C trackpad and other input
drivers.
Also we switched to use __maybe_unused instead of gating suspend/
resume code with #ifdef guards to get better compile coverage"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (27 commits)
Input: gpio_keys - fix warning regarding uninitialized 'button' variable
Input: add support for Elan eKTH I2C touchscreens
Input: gpio_keys - fix warning regarding uninitialized 'irq' variable
Input: cyapa - use 'error' for error codes
Input: cyapa - fix resuming the device
Input: gpio_keys - add device tree support for interrupt only keys
Input: amikbd - allocate temporary keymap buffer on the stack
Input: amikbd - fix build if !CONFIG_HW_CONSOLE
Input: lm8323 - missing error check in lm8323_set_disable()
Input: initialize device counter variables with -1
Input: initialize input_no to -1 to avoid subtraction
Input: i8042 - do not try to load on Intel NUC D54250WYK
Input: atkbd - correct MSC_SCAN events for force_release keys
Input: cyapa - switch to using managed resources
Input: lifebook - use "static inline" instead of "inline" in lifebook.h
Input: touchscreen - use __maybe_unused instead of ifdef around suspend/resume
Input: mouse - use __maybe_unused instead of ifdef around suspend/resume
Input: misc - use __maybe_unused instead of ifdef around suspend/resume
Input: cap11xx - support for irq-active-high option
Input: cap11xx - add support for various cap11xx devices
...
Fixed a coding style error, macros with complex values should be
enclosed in parentheses.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This driver supports Elan eKTH I2C touchscreen controllers. Note that these
are using custom protocol, as opposed to other Elan parts that use
HID-over-I2C and are supported by the standard HID-multitouch driver.
Signed-off-by: Scott Liu <scott.liu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
The alternative of CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME may be
replaced with CONFIG_PM too.
Make these changes in 2 files under drivers/input/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use __maybe_unused instead of ifdef guards around suspend/resume
functions, in order to increase build coverage and fix build warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
Add a driver for the Goodix touchscreen panel found in Onda v975w tablets.
The driver is based off the Android driver gt9xx.c found in some Android
code dumps, but now bears no resemblance to the original driver.
The driver was tested on the aforementioned tablet.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sharp SL-6000 (tosa) touchscreen needs wider limits to properly map all
points on the screen. Expand ranges in abs_x and abs_y arrays according
to the touchscreen area.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull second round of input updates from Dmitry Torokhov:
"Mostly simple bug fixes, although we do have one brand new driver for
Microchip AR1021 i2c touchscreen.
Also there is the change to stop trying to use i8042 active
multiplexing by default (it is still possible to activate it via
i8042.nomux=0 on boxes that implement it)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add Thrustmaster as Xbox 360 controller vendor
Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
Input: max77693-haptic - fix state check in imax77693_haptic_disable()
Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
Input: alps - fix v4 button press recognition
Input: i8042 - disable active multiplexing by default
Input: i8042 - add noloop quirk for Asus X750LN
Input: synaptics - gate forcepad support by DMI check
Input: Add Microchip AR1021 i2c touchscreen
Input: cros_ec_keyb - add of match table
Input: serio - avoid negative serio device numbers
Input: avoid negative input device numbers
Input: automatically set EV_ABS bit in input_set_abs_params
Input: adp5588-keys - cancel workqueue in failure path
Input: opencores-kbd - switch to using managed resources
Input: evdev - fix EVIOCG{type} ioctl
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp. The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUMZqoAAoJEHm+PkMAQRiGFC4H/i0b9vxCwe6VCXonpaDW03fI
JKE7v/zwDfhDngKSYfBWRSf3jXwfSHLvAvCgIvqTw5qBW3XSWF8xB7kJpWptQxIi
M6ePfaETt2mPYhEWWWxJK8boykiOXObDrFJVhfjHGsjbvmKiLPMaGYwXTSwZJ32V
fQDaA9Piugjc9wEY0d+6cjqUUEwlb4+GFz4Wv2oJgbpzxwgJS/XjQYk+3PrcdAXz
lmwPXQ+6ntJaducVu3JM2YYvaJLzTw+T+MPsWiTvaE4ILmuiw492VNY5XdyQQtb2
DSActOKCF2hIwnG+DMg63XV5FH81HqczwORDygBuxko0cURxupxMnaLPkVRpksk=
=+PRQ
-----END PGP SIGNATURE-----
Merge tag 'v3.17' into next
Synchronize with mainline to bring in changes to Synaptics and i8042
drivers.
This patch adds support for the ar1021 i2c based touchscreen.
The driver is quite simple and only supports the Touch
Reporting Protocol.
This is the final version for an RFC patch send a while ago.
http://www.spinics.net/lists/linux-input/msg29419.html
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Nick Dyer: reworked to move free of input device into separate function
and only call in paths that require it.]
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the case where the CHG/interrupt line mode is not configured correctly,
this warning is output to dmesg output for each interrupt. Downgrade the
message to debug.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Somehow we ended up with a duplicate line in edt_ft5x06_register_write()
Signed-off-by: Maks Naumov <maksqwe1@ukr.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This should fix the following issues reported by Coverity:
*** CID 1230625: Logically dead code (DEADCODE)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1692 in mxt_initialize()
*** CID 1230627: Missing break in switch (MISSING_BREAK)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1436 in mxt_get_object_table()
*** CID 1230629: Out-of-bounds write (OVERRUN)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1267 in mxt_update_cfg()
*** CID 1230632: Unused pointer value (UNUSED_VALUE)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1211 in mxt_update_cfg()
Acked-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's split config update code a bit so it is hopefully a bit easier to
read. Also, the firmware update callback should be the entity releasing
firmware blob, not lower layers.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
I think having control flow with 2 goto/labels/flags is quite hard to read,
this version is a bit more readable IMO.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
This switches the driver to using managed resources to simplify error
handling and to do away with remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We can annonate the suspend/resume functions with '__maybe_unused' and get
rid of the ifdef, which makes the code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When a kernel has CONFIG_PM=y and CONFIG_PM_SLEEP=n the following warnings are
seen:
drivers/input/touchscreen/mcs5000_ts.c:252:12: warning: 'mcs5000_ts_suspend' defined but not used [-Wunused-function]
static int mcs5000_ts_suspend(struct device *dev)
^
drivers/input/touchscreen/mcs5000_ts.c:262:12: warning: 'mcs5000_ts_resume' defined but not used [-Wunused-function]
static int mcs5000_ts_resume(struct device *dev)
Protect the suspend/resume functions with CONFIG_PM_SLEEP in order to fix these
build warnings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Input device must be released(input_free_device) when ads7846_probe_dt
fails. This fixes the same by releasing resources on failure.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By writing zero to both the active and idle cycle times the maXTouch device
is put into a deep sleep mode when it consumes minimal power. It is
unnecessary to change the configuration of any other objects (for example
to disable T9 touchscreen).
It is counterproductive to reset the chip on resume, it will result in a
long delay. However it is necessary to issue a calibrate command after the
chip has spent any time in deep sleep.
This patch also deals with the situation where the power configuration is
zero on probe, which would mean that the device never wakes up to execute
commands.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Provide device tree support and binding information. Also provide support
for a new chip "pixcir_tangoc".
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some variants of the Pixcir touch controller support up to 5 simultaneous
fingers and hardware tracking IDs. Prepare the driver for that.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch to using the Type-B Multi-Touch protocol.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wire up open/close so we do not try to send events until someone uses them;
this also allows us to remove micro_ts_remove() and rely fully on managed
resources.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
