Only contact firmware if it's alive _AND_ if use_bd (use backdoor
access) is not set when issuing FW_LDST_CMD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware reports error, reset FW_OK flag.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like PF, if the int_gl_idx of VF does not be set, the default
interrupt coalesce index of VF is 0. But it should be GL1 for TX
queues and GL0 for RX queues.
This patch adds the int_gl_idx setup for VF.
Fixes: 200ecda42598 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ethtool_ops.get/set_coalesce support to VF.
Since PF and VF share the same get/set_coalesce interface,
we only need to set hns3_get/set_coalesce to the ethtool_ops
when supporting get/set_coalesce for VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlpq+ZkTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9mFcB/wPSu30a664/+wjUvXM7Zdw4ko/PRdS
deSRnjGj3epkHRyGJkdGSuPx9iGg3pqR8poMCZZmFUG+kGBmEcGQX+eyaR41zIUz
iyEgZSufYDjsW47eGBsNE01xQjoL1jcF9JM7NHmRrw4+2YF75cGE3BOGcmcV6Hjc
O5HDIpLmbeMHI4NcujgD4UG/VPnZQw3+oN9eyYUEbY5Aa2XQyW76DIJ3SyKsHQz0
K/s0uxAGo+Ap7xuoBUJpx6BBYoHYM171DTgXfH9pUB0MwqyDCq3hAyYGR+UEdIXb
IDhIcN/l5wFU8VICjYmSKgKyjjHqlixgoki2snmJxVWu0KeVl5LJ1Edv
=7jiC
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.16-20180126' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2018-01-26
this is a pull request for net-next/master consisting of 3 patches.
The first two patches target the CAN documentation. The first is by me
and fixes pointer to location of fsl,mpc5200-mscan node in the mpc5200
documentation. The second patch is by Robert Schwebel and it converts
the plain ASCII documentation to restructured text.
The third patch is by Fabrizio Castro add the r8a774[35] support to the
rcar_can dt-bindings documentation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commit ec718254cb
("ixgbe: Improve performance and reduce size of ixgbe_tx_map")
This change is meant to both improve the performance and reduce the size of
ixgbevf_tx_map().
Expand the work done in the main loop by pushing first into tx_buffer.
This allows us to pull in the dma_mapping_error check, the tx_buffer value
assignment, and the initial DMA value assignment to the Tx descriptor.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on commit d2bead576e
("igb: Clear Rx buffer_info in configure instead of clean")
This change makes it so that instead of going through the entire ring on Rx
cleanup we only go through the region that was designated to be cleaned up
and stop when we reach the region where new allocations should start.
In addition we can avoid having to perform a memset on the Rx buffer_info
structures until we are about to start using the ring again.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We already had placehloders for failed page and buffer allocations.
Added alloc_rx_page and made sure the stats are properly updated and
exposed in ethtool.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on commit bd4171a5d4
("igb: update code to better handle incrementing page count")
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on commit 5be5955425
("igb: update driver to make use of DMA_ATTR_SKIP_CPU_SYNC")
and
commit 7bd1759282 ("igb: Add support for DMA_ATTR_WEAK_ORDERING")
Convert the calls to dma_map/unmap_page() to the attributes version
and add DMA_ATTR_SKIP_CPU_SYNC/WEAK_ORDERING which should help
improve performance on some platforms.
Move sync_for_cpu call before we perform a prefetch to avoid
invalidating the first 128 bytes of the packet on architectures where
that call may invalidate the cache.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on:
commit 7ec0116c91 ("igb: Use length to determine if descriptor is done")
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
In addition we only reset the Rx descriptor length for descriptor zero when
resetting a ring instead of having to do a memset with 0 over the entire
ring. By doing this we can save some time on initialization.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on commit 64f2525ca4 ("igb: Only DMA sync frame length")
On some architectures synching a buffer for DMA may be expensive.
Instead of the entire 2K receive buffer only synchronize the length of
the frame, which will typically be the MTU or smaller.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce ixgbevf_can_reuse_page() similar to the change in ixgbe from
commit af43da0dba
("ixgbe: Add function for checking to see if we can reuse page")
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes: 1280c0f8aa ("sfc: support second + quarter ns time format for receive datapath")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel documentation is now restructured text. Convert the SocketCAN
documentation and include it in the toplevel kernel documentation.
This patch doesn't do any content change.
All references to can.txt in the code are converted to can.rst.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Apparently hardware does not perform CCMP PN validation in hardware, so
we need to take care of this in the driver. This is important for
protecting against replay attacks.
Since validation of fragmented frames is more complex, the CCMP header
for those is preserved. To keep the counter in sync, the first fragment
is verified by both mt76 and mac80211, and all other fragments only by
mac80211.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a separate function for processing frames after A-MPDU reordering,
reduce code duplication
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is required for performing CCMP PN validation in software
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoids the rhashtable lookup based on the MAC address inside mac80211
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preparation for passing in more internal rx data via skb->cb
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Like beacons, probe responses need a hardware-generated TSF value. Set
the flag that causes the hw to generate it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sending frames to mac80211 needs time, which could allow for more rx
packets to end up in the DMA ring. Retry polling until there are no more
frames left. Improves rx latency under load.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sukumar reported that sends to the local broadcast address
(255.255.255.255) are broken. Check for the address in vrf driver
and do not redirect to the VRF device - similar to multicast
packets.
With this change sockets can use SO_BINDTODEVICE to specify an
egress interface and receive responses. Note: the egress interface
can not be a VRF device but needs to be the enslaved device.
https://bugzilla.kernel.org/show_bug.cgi?id=198521
Reported-by: Sukumar Gopalakrishnan <sukumarg1973@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware statistics retrieval hurts in tight invocation loops.
Avoid extraneous write and enforce strict ordering of writes targeted to
the tally counters dump area address registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Oliver Freyermuth <o.freyermuth@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue found by checkpatch.
Signed-off-by: Rohit Visavalia <rohit.visavalia@softnautics.com>
Acked-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolved Warning: networking block comments don't use an empty /* line,
use /* Comment...
Issue found by checkpatch.
Signed-off-by: Rohit Visavalia <rohit.visavalia@softnautics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_wr_mbox_meat_timeout() can be called from both softirq
context and process context, hence protect the mbox with
spin_lock_bh() instead of simple spin_lock()
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some dst_ops (e.g. md_dst_ops)) doesn't set this handler. It may result to:
"BUG: unable to handle kernel NULL pointer dereference at (null)"
Let's add a helper to check if update_pmtu is available before calling it.
Fixes: 52a589d51f ("geneve: update skb dst pmtu on tx path")
Fixes: a93bf0ff44 ("vxlan: update skb dst pmtu on tx path")
CC: Roman Kapl <code@rkapl.cz>
CC: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support increased precision frequency adjustment format (FP44) used
by Medford2 adapters.
Signed-off-by: Laurence Evans <levans@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time_format that we stash in the PTP data structure is never
referenced, so we can remove it. Instead, store the information needed
to interpret sync event timestamps.
Also rolls in a couple of other related minor PTP fixes.
Based on patches by Bert Kenward <bkenward@solarflare.com> and Laurence
Evans <levans@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support MC_CMD_PTP_OUT_GET_TIMESTAMP_CORRECTIONS_V2. Extract general
timestamp corrections in addition to PTP corrections. Apply receive
timestamp corrections for general datapath receive timestamping, and
correspondingly for transmit.
Signed-off-by: Laurence Evans <levans@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timestamp conversion function with correction to avoid duplicate
correction handling.
Signed-off-by: Laurence Evans <levans@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We check the license for TX hardware timestamping capability.
The PTP probe will have enabled PTP sync events from the adapter. If
later, at TX queue init, it turns out we do not have the license, we
don't need the sync events either.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For this we create and use one or more new TX queues on the PTP channel,
and enable sync events for it.
Based on a patch by Martin Habets <mhabets@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX timestamps on 8000 series are supplied from the MAC. This timestamp is
only 48 bits long. The high order bits from the last time sync event are
used for the top 16 bits.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we try to enable the feature and do not have the license for it, the
MCPU will refuse and fail our TX queue init.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now transmit SKBs in 2 ways:
1. Via the MC (for the 7XXX series and earlier), using
efx_ptp_xmit_skb_mc().
2. Via the TX queues on the dedicated PTP channel (8XXX series and later),
using efx_ptp_xmit_skb_queue().
The PTP worker thread uses the method set up at probe time. It never
checked the return code from the old efx_ptp_xmit_skb(), so it now
returns void.
We increment the TX dropped counter of the device if the transmit fails.
As a result of the probe per channel the remove gets called multiple times.
Clean up efx->ptp_data properly to avoid the 2nd call blowing up.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MC capability MC_CMD_GET_CAPABILITIES_V2_OUT_TX_MAC_TIMESTAMPING to
detect whether the NIC supports timestamping packets sent out the main
datapath.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this work, TX timestamping is done by sending each SKB to the MC.
On the 8000 series (Medford1) we have high speed timestamping via the
MAC, which means we can use normal TX queues for this without a
significant drop in bandwidth. On the X2000 series (Medford2) support
for transmitting via the MC is removed, so the new way must be used.
This patch enables timestamping on a TX queue, if requested.
It also enhances TX event handling to process the extra completion events,
and puts the time in the SKB.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NAPI budget is only for RX processing work, not other work such as
TX or MCDI completion handling.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.16. Major changes:
wil6210
* add PCI device id for Talyn
* support flashless device
ath9k
* improve RSSI/signal accuracy on AR9003 series
Add 'static' or declaration to resolve the warnings, and remove two unused
functions halbtc_set_macreg() and halbtc_get_macreg() exposed when they
were made static.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx_dxe_init() doesn't check for the return value of
wcn36xx_dxe_init_descs(), release the resources in case an error ocurred.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 series allows to calibrate noise floor for different frequency
bins. Once it's done it's possible to get more accurate rssi/signal
values over whole frequency band at a given temperature.
The RSSI/signal accuracy reported by calibrated RF cards improves
from 6 to up to 2dB.
This could be interesting for application which require good signal
accuracy like roaming or mesh protocols.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 devices can have calibrated noise floor values
which can be used instead of hard coded one. Read them
from eeprom and save interpolated value in nf limits for
the current channel.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 factory calibration allows to use bigger EEPROM than
standard 1k without changing the default layout. Allow
probing of EEPROM at alternative address if initial check
for default fails.
The original ar9003 eeprom ops are still be used.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to allow using the same brd file across different
11ad chips, the address for loading the brd file should be
part of the FW file, instead of the brd file. The brd file is
expected to include only one section.
To allow backward compatibility the driver reads the
address from the brd file in case it is not included in the
FW file.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sparrow D0 chips have slightly larger mac_rgf_ext section
in order to support extra features such as multiple virtual
interfaces.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when we want to bring the interface up, we first
reset the device which causes the boot loader to run. Then
we halt the device CPU, load FW image and resume the device
CPU.
There are some boot loader versions which perform redundant
memory accesses even when idle. Halting the device CPU
while boot loader access memory can cause the device memory
controller to get stuck, the FW will fail to load and the
network interface will not come up.
For such boot loaders implement a workaround where we freeze
the boot loader before halting the device CPU, so it will not
perform any memory accesses.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
OTP HW vectors values are different for 40MHz and 330MHz AHB
clocks.
In SW reset flow, the host driver sets the clock frequency
to 40MHz. In order to allow reading from the OTP, the host
driver should configure the OTP HW vectors with the values
that fits this clock frequency.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn device supports boot without flash.
Driver detects flashless device and in this case waits for ready indication
from HW machine (instead of bootloader ready indication). Also in this
case, MAC address is retrieved from OTP.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn memory has changed, areas were increased and shifted
to new locations.
Use the appropriate address map according to the device JTAG ID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add Talyn JTAG ID to the list of valid IDs
and identify this device as Talyn.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PCIe device ID has changed in Talyn.
Add this ID to wil6210_pcie_ids list to allow
recognition of Talyn device.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA control register has areas of mode and opcodes for opeations. 18 bit is
using for mode selection, where 0 is old MIO/MDIO access method and 1 is
indirect access mode. 19-20 bits are using for setting up read/write
operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode
with 19 bit and write operation is set into 18 bit which is mode selection,
not a write operation. To correlate write with read we set it into 20 bit.
All those bit operations are MSB 0 based.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes,
in current state if we set it up in dts 8192 as example, we will get
only 2048 which may impact on network speed.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-01-24
This series contains updates to fm10k only.
Alex fixes MACVLAN offload for fm10k, where we were not seeing unicast
packets being received because we did not correctly configure the
default VLAN ID for the port and defaulting to 0.
Jake cleans up unnecessary parenthesis in a couple of "if" statements.
Fixed the driver to stop adding VLAN 0 into the VLAN table, since it
would cause the VLAN table to be inconsistent between the PF and VF.
Also fixed an issue where we were assuming that VLAN 1 is enabled when
the default VLAN ID is not set, so resolve by not requesting any filters
for the default_vid if it has not yet been assigned.
Ngai fixes an issue which was generating a dmesg regarding unbale to
kill a particular VLAN ID for the device. This is due to
ndo_vlan_rx_kill_vid() exits with an error and the handler for this ndo
is fm10k_update_vid() which exits prematurely under PF VLAN management.
So to resolve, we must check the VLAN update action type before exiting
fm10k_update_vid(), and act appropriately based on the action type.
Also corrected code comment typos.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify the comment for when entering promiscuous mode that we update
the VLAN table. Add a comment distinguishing the case where we're
exiting promiscuous mode and need to clear the entire VLAN table.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@gmail.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 856dfd69e84f ("fm10k: Fix multicast mode synch issues",
2016-03-03) we've incorrectly assumed that VLAN 1 is enabled when the
default VID is not set.
This occurs because we check the default_vid and if it's zero, start
several loops over the active_vlans bitmask at 1, instead of checking to
ensure that that bit is active.
This happened because of commit d9ff3ee8efe9 ("fm10k: Add support for
VLAN 0 w/o default VLAN", 2014-08-07) which mistakenly assumed that we
should send requests for MAC and VLAN filters with VLAN 0 when the
default_vid isn't set.
However, the switch generally considers this an invalid configuration,
so the only time we'd have a default_vid of 0 is when the switch is
down.
Instead, lets just not request any filters for the default_vid if it's
not yet been assigned.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, when the driver loads, it sends a request to add VLAN 0 to the
VLAN table. For the PF, this is honored, and VLAN 0 is indeed set. For
the VF, this request is silently converted into a request for the
default VLAN as defined by either the switch vid or the PF vid.
This results in the odd behavior that the VLAN table doesn't appear
consistent between the PF and the VF.
Furthermore, setting a MAC filter with VLAN 0 is generally considered an
invalid configuration by the switch, and since commit 856dfd69e84f
("fm10k: Fix multicast mode synch issues", 2016-03-03) we've had code
which prevents us from ever sending such a request.
Since there's not really a good reason to keep VLAN 0 in the VLAN table,
stop requesting it in fm10k_restore_rx_state().
This might seem to indicate that we would no longer properly configure
the MAC and VLAN tables for the default vid. However, due to the way
that fm10k_find_next_vlan() behaves, it will always return the
default_vid as enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a VF is under PF VLAN assignment:
ip link set <pf> vf <#> vlan <vid>
This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":
failed to kill vid 0081/<vid> for device <vf>
This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.
Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.
The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.
However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes a few warnings found by checkpatch.pl --strict
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warning:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_flower.c:46:27: warning:
symbol 'pedits' was not declared. Should it be static?
Fixes: 27ece1f357 ("cxgb4: add tc flower support for ETH-DMAC rewrite")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a768 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A tid was allocated for reserved MR during initialization but
not freed. This lead to an annoying output message during
rdma unload flow.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Double reservation for kernel dedicated dpi was performed.
Once in the core module and once in qedr.
Remove the reservation from core.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fm10k driver didn't work correctly when macvlan offload was enabled.
Specifically what would occur is that we would see no unicast packets being
received. This was traced down to us not correctly configuring the default
VLAN ID for the port and defaulting to 0.
To correct this we either use the default ID provided by the switch or
simply use 1. With that we are able to pass and receive traffic without any
issues.
In addition we were not repopulating the filter table following a reset. To
correct that I have added a bit of code to fm10k_restore_rx_state that will
repopulate the Rx filter configuration for the macvlan interfaces.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bit TPD3[31] is used as a timestamp bit if PTP is enabled, but
it's used as an address bit if PTP is disabled. Since PTP isn't
supported by the driver, we can extend the DMA address to 46 bits.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing a bitwise AND between a bool and an int is generally not a good idea.
The bool will be promoted to an int with value 0 or 1,
the int is generally regarded as true with a non-zero value,
thus ANDing them has the potential to yield an undesired result.
This commit fixes the following smatch warnings:
drivers/net/ethernet/stmicro/stmmac/enh_desc.c:344 enh_desc_prepare_tx_desc() warn: maybe use && instead of &
drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c:337 dwmac4_rd_prepare_tx_desc() warn: maybe use && instead of &
drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c:380 dwmac4_rd_prepare_tso_tx_desc() warn: maybe use && instead of &
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem description:
After ethernet cable connect and disconnect for several iterations on a
device with i210, tx timestamp will stop being put into the socket.
Steps to reproduce:
1. Setup a device with i210 and wire it to a 802.1AS capable switch (
Extreme Networks Summit x440 is used in our case)
2. Have the gptp daemon running on the device and make sure it is synced
with the switch
3. Have the switch disable and enable the port, wait for the device gets
resynced with the switch
4. Iterates step 3 until the device is not albe to get resynced
5. Review the log in dmesg and you will see warning message "igb : clearing
Tx timestamp hang"
Root cause:
If ptp_tx_work() gets scheduled just before the port gets disabled, a LINK
DOWN event will be processed before ptp_tx_work(), which may cause timeout
in ptp_tx_work(). In the timeout logic, the TSYNCTXCTL's TXTT bit (Transmit
timestamp valid bit) is not cleared, causing no new timestamp loaded to
TXSTMP register. Consequently therefore, no new interrupt is triggerred by
TSICR.TXTS bit and no more Tx timestamp send to the socket.
Signed-off-by: Daniel Hua <daniel.hua@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I personally spent a long time trying to decypher why my CPU would not
reach deeper C-states. Let's just tell the next user what's going on.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By design, the idleslope increments are restricted to 16.384kbps steps.
Add a comment to igb_main.c making that explicit and add one example
that illustrates the impact of that.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to section 12.0.3.4.13 "Receive Descriptor Control - RXDCTL"
of the Intel® 82579 Gigabit Ethernet PHY Datasheet v2.1:
"HTHRESH should be given a non zero value when ever PTHRESH is
used."
In RXDCTL(0), PTHRESH lives at bits 5:0, and HTHREST lives at bits 13:8.
Set only bit 8 of HTHREST as is done in e1000_flush_rx_ring(). Found by
inspection.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new function igb_get_max_rss_queues() to get maximum
RSS queues, this will reduce duplicate code and facilitate future
maintenance.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Before libvirt modifies the MAC address and vlan tag for an SRIOV VF
for use by a virtual machine (either using vfio device assignment or
macvtap passthru mode), it saves the current MAC address and vlan tag
so that it can reset them to their original value when the guest is
done. Libvirt can't leave the VF MAC set to the value used by the
now-defunct guest since it may be started again later using a
different VF, but it certainly shouldn't just pick any random value,
either. So it saves the state of everything prior to using the VF, and
resets it to that.
The igb driver initializes the MAC addresses of all VFs to
00:00:00:00:00:00, and reports that when asked (via an RTM_GETLINK
netlink message, also visible in the list of VFs in the output of "ip
link show"). But when libvirt attempts to restore the MAC address back
to 00:00:00:00:00:00 (using an RTM_SETLINK netlink message) the kernel
responds with "Invalid argument".
Forbidding a reset back to the original value leaves the VF MAC at the
value set for the now-defunct virtual machine. Especially on a system
with NetworkManager enabled, this has very bad consequences, since
NetworkManager forces all interfacess to be IFF_UP all the time - if
the same virtual machine is restarted using a different VF (or even on
a different host), there will be multiple interfaces watching for
traffic with the same MAC address.
To allow libvirt to revert to the original state, we need a way to
remove the administrative set MAC on a VF, to allow normal host
operation again, and to reset/overwrite the VF MAC via VF netdev.
This patch implements the outlined scenario by allowing to set the
VF MAC to 00:00:00:00:00:00 via RTM_SETLINK on the PF.
igb_ndo_set_vf_mac resets the IGB_VF_FLAG_PF_SET_MAC flag to 0,
so it's possible to reset the VF MAC back to the original value via
the VF netdev.
Note: Recent patches to libvirt allow for a workaround if the NIC
isn't capable of resetting the administrative MAC back to all 0, but
in theory the NIC should allow resetting the MAC in the first place.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <arron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using the firmware api it can fail simply because firmware does
not like the request or it fails due to issues in the host interface.
Currently, there is only a single error code which is confusing. So
adding a parameter to pass the firmware error separately and in case
of a firmware error always return -EBADE to user-space.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The protocol layer api defines callbacks for dongle commands.
Although not really well documented these should only return an
error code in case of an error, or 0 upon success. In the bcdc
protocol it can return value above 0 and we carry a fix in the
caller of the protocol layer api. This patch makes it adhere to
the intent of the api as described above.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Events processing requires locking of bus mutex, which is also used by
cfg80211 layer before calling several of cfg80211 callbacks. Since all
cfg80211 callbacks in qtnfmac driver also lock bus mutex, this
potentially may lead to a deadlock.
Do not use bus lock for event processing. Use RTNL lock instead to
serialize events and commands processing threads.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function qtnf_scan_done makes use of mutexes which is wrong
since it may be called from timer context. Move scan timeout
handler from timer to deferred work.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA does not reconnect to the same AP after disconnect. The reason is
that STA is marked as disconnected in cfg80211 disconnect callback.
This is too early since in this case qtnfmac event handler skips
cfg80211_disconnected call when processing disconnect event from
the card. As a result, wdev is left in an inconsistent state.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Validate new interface combinations using wireless core checks when new
interface is added or when the type of existing interface is modified.
This is performed to make sure that new interface combination is supported
by hardware. As a result, invalid interface combinations are rejected early,
rather than passed to hardware with sometimes unpredictable results.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update existing code handling configuration of supported interface
combinations. Current implementation is not complete since it does
not report multiple interface combinations which are incompatible
with each other. Instead current implementation packs all the
supported combinations into single entry.
In fact currently qsr10g wireless card supports the following
two distinct interface combinations:
1. STA/repeater: 1 STA and/or 1 AP
{
{ .max = 1, .types = NL80211_IFTYPE_AP},
{ .max = 1, .types = NL80211_IFTYPE_STA},
}
2. AP/mBSS
{
{ .max = 8, .types = NL80211_IFTYPE_AP},
}
The list of supported configuration is reported by firmware during
wireless card bring-up. Communication protocol between firmware
and host has been updated accordingly in order to accommodate passing
multiple interface combination entries.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable reporting of qtnfmac hardware and firmware details
using ethtool command.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various bits of hardware and firmware versions are useful for debug
and troubleshooting. Get more information from the wireless card.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On 32-bit platforms packet counters are stored in a net_device_stats struct
as unsigned long integers. As a result, after some time of network activity
an overflow takes place in network packet counters. This patch makes use of
new structs for holding interface statistics.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Virtual interface should be deleted after calling unregister_netdevice
since this function ends up with sending updown_intf command to card.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV is used to pass ACL data to firmware in start_ap cfg80211 callback.
Use the same approach in set_mac_acl cfg80211 callback.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver periodically samples all neighbors configured in device
in order to update the kernel regarding their state. When finding
an entry configured in HW that doesn't show in neigh_lookup()
driver logs an error message.
This introduces a race when removing multiple neighbors -
it's possible that a given entry would still be configured in HW
as its removal is still being processed but is already removed
from the kernel's neighbor tables.
Simply remove the error message and gracefully accept such events.
Fixes: c723c735fa ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Fixes: 60f040ca11 ("mlxsw: spectrum_router: Periodically dump active IPv6 neighbours")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memset variables to 0 to fix sparse warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_cudbg.c:409:42: sparse: Using
plain integer as NULL pointer
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:43:47: sparse: Using
plain integer as NULL pointer
Fixes: ad75b7d32f ("cxgb4: implement ethtool dump data operations")
Fixes: 91c1953de3 ("cxgb4: use zlib deflate to compress firmware dump")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes:
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:39:5: error:
redefinition of 'cudbg_compress_buff'
int cudbg_compress_buff(struct cudbg_init *pdbg_init,
^~~~~~~~~~~~~~~~~~~
In file included from
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:23:0:
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.h:45:19: note: previous
definition of 'cudbg_compress_buff' was here
static inline int cudbg_compress_buff(struct cudbg_init *pdbg_init,
^~~~~~~~~~~~~~~~~~~
Fixes: 91c1953de3 ("cxgb4: use zlib deflate to compress firmware dump")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
implement ndo_set_vf_vlan for mgmt netdevice to configure
the PCIe VF.
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field spec_ver is IC's specification mask for common code to do proper
process to specified IC. This commit add a field new rate ID for new
generation IC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New generation ICs will support 11ac, 5G, n-NSS, etc, so we define a set of
rate ID.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8822be is 2x2 11ac wifi chip, so report VHT capability to mac80211.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In files halbtc8822b1ant.c and halbtc8822b2ant.c that I will submit later,
two undesired directives named BT_8822B_1ANT_COEX_DBG and
BT_8822B_2ANT_COEX_DBG will be replaced by boolean variables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Originally, btcoex controls the antenna of combo card, but solo card
is also needed to setup properly. The new ops are named with suffix
'_wifi_only' opposited to original btc_ops, and new structures and
definitions are also introduced. The wifi_only oly contains four ops that
are initial variable, hw config, scan notify, and switch band notify.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Three steps of connection procedure are scan, enter/leave IPS, auth.
There is no scan between leaving IPS and sending auth, but btcoex use scan
as an important clue that indicates user is going to connect. So add scan
notifications in ips_notify to correct btcoex's state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable will be used by btcoex of 8822be, so we prepare this variable
in advance.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BT shares 2.4G band but not 5G band, so inform current band to btcoex to
setup antenna properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rtlwifi newer ICs support 80M bandwidth in 5G band, so extend
get_wifi_bw() to know bandwidth 80M that helps btcoex to make correct
decisions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a possible race in mt76x2_stop_hardware() since pre_tbtt and
dfs tasklets could run during driver cleanup. Fix it disabling all
pending tasklets during device removal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not enable DFS state machine if dfs region is set to NL80211_DFS_UNSET
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add mt76x2_dfs_set_domain routine in order to properly reconfigure
pattern detector when DFS domain has been changed
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Substitute tasklet_kill with tasklet_disable/tasklet_enable in order to
guarantee dfs tasklet can not be executed during dfs parameter
initialization
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hardware encryption seems to break encrypted unicast mgmt tx.
Unfortunately the hardware TXWI header does not have a bit to indicate
that a frame is software encrypted, so sw-encrypted frames need to use a
different WCID. For that to work, the CCMP PN needs to be generated in
software, which makes things a bit slower, so only do it for keys that
also need to tx management frames.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix hw queue configuration since mt76x2 devices use a reverse queue
enumeration respect to mac80211 one:
- 0: AC_BE
- 1: AC_BK
- 2: AC_VI
- 3: AC_VO
The issue can be reproduced sending two concurrent flow using
two separate queues:
- VO: 20Mbps UDP traffic
- BE: TCP traffic
In this scenario the UDP traffic will be blocked by the TCP one.
Fix it configuring properly WMM hw queue parameters
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Tested-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make netdevsim print a message to the BPF verifier log buffer when a
program is offloaded.
Then use this message in hardware offload selftests to make sure that
using this buffer actually prints the message to the console for
eBPF hardware offload.
The message is appended after the last instruction is processed with the
verifying function from netdevsim. Output looks like the following:
$ tc filter add dev foo ingress bpf obj sample_ret0.o \
sec .text verbose skip_sw
Prog section '.text' loaded (5)!
- Type: 3
- Instructions: 2 (0 over limit)
- License:
Verifier analysis:
0: (b7) r0 = 0
1: (95) exit
[netdevsim] Hello from netdevsim!
processed 2 insns, stack depth 0
"verbose" flag is required to see it in the console since netdevsim does
not throw an error after printing the message.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not compile netdevsim/bpf.c if BPF syscall is not
enabled. Otherwise bpf core would have to provide wrappers
for all functions offload drivers may call, even though
system will never see a BPF object.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the recently added extack support for TC eBPF filters in netdevsim.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-01-23
This series contains updates to i40e and i40evf only.
Pawel enables FlatNVM support on x722 devices by allowing nvmupdate tool
to configure the preservation flags in the AdminQ command.
Mitch fixes a potential divide by zero error when DCB is enabled and
the firmware fails to configure the VSI, so check for this state.
Fixed a bug where the driver could fail to adhere to ETS bandwidth
allocations if 8 traffic classes were configured on the switch.
Sudheer fixes a potential deadlock by avoiding to call
flush_schedule_work() in i40evf_remove(), since cancel_work_sync()
and cancel_delayed_work_sync() already cleans up necessary work items.
Fixed an issue with the problematic detection and recovery from
hung queues in the PF which was causing lost interrupts. This is done
by triggering a software interrupt so that interrupts are forced on
and if we are already in napi_poll and an interrupt fires, napi_poll
will not be rescheduled and the interrupt is lost.
Avinash fixes an issue in the VF where is was possible to issue a
reset_task while the device is currently being removed.
Michal fixes an issue occurring while calling i40e_led_set() with
the blink parameter set to true, which was causing the activity LED
instead of the link LED to blink for port identification.
Shiraz changes the client interface to not call client close/open on
netdev down/up events, since this causes a lot of thrash that is
not needed. Instead, disable the PE TCP-ENA flag during a netdev
down event and re-enable on a netdev up event, since this blocks all
TCP traffic to the RDMA protocol engine.
Alan fixes an issue which was causing a potential transmit hang by
ignoring the PF link up message if the VF state is not yet in the
RUNNING state.
Amritha fixes the channel VSI recreation during the reset flow to
reconfigure the transmit rings and the queue context associated with
the channel VSI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
with the introduction of commit
b0eb57cb97, it appears that rq->buf_info
is improperly handled. While it is heap allocated when an rx queue is
setup, and freed when torn down, an old line of code in
vmxnet3_rq_destroy was not properly removed, leading to rq->buf_info[0]
being set to NULL prior to its being freed, causing a memory leak, which
eventually exhausts the system on repeated create/destroy operations
(for example, when the mtu of a vmxnet3 interface is changed
frequently.
Fix is pretty straight forward, just move the NULL set to after the
free.
Tested by myself with successful results
Applies to net, and should likely be queued for stable, please
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-By: boyang@redhat.com
CC: boyang@redhat.com
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: David S. Miller <davem@davemloft.net>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In pppoe_sendmsg(), reserving dev->hard_header_len bytes of headroom
was probably fine before the introduction of ->needed_headroom in
commit f5184d267c ("net: Allow netdevices to specify needed head/tailroom").
But now, virtual devices typically advertise the size of their overhead
in dev->needed_headroom, so we must also take it into account in
skb_reserve().
Allocation size of skb is also updated to take dev->needed_tailroom
into account and replace the arbitrary 32 bytes with the real size of
a PPPoE header.
This issue was discovered by syzbot, who connected a pppoe socket to a
gre device which had dev->header_ops->create == ipgre_header and
dev->hard_header_len == 0. Therefore, PPPoE didn't reserve any
headroom, and dev_hard_header() crashed when ipgre_header() tried to
prepend its header to skb->data.
skbuff: skb_under_panic: text:000000001d390b3a len:31 put:24
head:00000000d8ed776f data:000000008150e823 tail:0x7 end:0xc0 dev:gre0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 3670 Comm: syzkaller801466 Not tainted
4.15.0-rc7-next-20180115+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:skb_panic+0x162/0x1f0 net/core/skbuff.c:100
RSP: 0018:ffff8801d9bd7840 EFLAGS: 00010282
RAX: 0000000000000083 RBX: ffff8801d4f083c0 RCX: 0000000000000000
RDX: 0000000000000083 RSI: 1ffff1003b37ae92 RDI: ffffed003b37aefc
RBP: ffff8801d9bd78a8 R08: 1ffff1003b37ae8a R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff86200de0
R13: ffffffff84a981ad R14: 0000000000000018 R15: ffff8801d2d34180
FS: 00000000019c4880(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000208bc000 CR3: 00000001d9111001 CR4: 00000000001606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
skb_under_panic net/core/skbuff.c:114 [inline]
skb_push+0xce/0xf0 net/core/skbuff.c:1714
ipgre_header+0x6d/0x4e0 net/ipv4/ip_gre.c:879
dev_hard_header include/linux/netdevice.h:2723 [inline]
pppoe_sendmsg+0x58e/0x8b0 drivers/net/ppp/pppoe.c:890
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:640
sock_write_iter+0x31a/0x5d0 net/socket.c:909
call_write_iter include/linux/fs.h:1775 [inline]
do_iter_readv_writev+0x525/0x7f0 fs/read_write.c:653
do_iter_write+0x154/0x540 fs/read_write.c:932
vfs_writev+0x18a/0x340 fs/read_write.c:977
do_writev+0xfc/0x2a0 fs/read_write.c:1012
SYSC_writev fs/read_write.c:1085 [inline]
SyS_writev+0x27/0x30 fs/read_write.c:1082
entry_SYSCALL_64_fastpath+0x29/0xa0
Admittedly PPPoE shouldn't be allowed to run on non Ethernet-like
interfaces, but reserving space for ->needed_headroom is a more
fundamental issue that needs to be addressed first.
Same problem exists for __pppoe_xmit(), which also needs to take
dev->needed_headroom into account in skb_cow_head().
Fixes: f5184d267c ("net: Allow netdevices to specify needed head/tailroom")
Reported-by: syzbot+ed0838d0fa4c4f2b528e20286e6dc63effc7c14d@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-01-23
This series contains updates to ixgbe only.
Shannon Nelson provides an implementation of the ipsec hardware offload
feature for the ixgbe driver for these devices: x540, x550, 82599.
The ixgbe NICs support ipsec offload for 1024 Rx and 1024 Tx Security
Associations (SAs), using up to 128 inbound IP addresses, and using the
rfc4106(gcm(aes)) encryption. This code does not yet support checksum
offload, or TSO in conjunction with the ipsec offload - those will be
added in the future.
This code shows improvements in both packet throughput and CPU utilization.
For example, here are some quicky numbers that show the magnitude of the
performance gain on a single run of "iperf -c <dest>" with the ipsec
offload on both ends of a point-to-point connection:
9.4 Gbps - normal case
7.6 Gbps - ipsec with offload
343 Mbps - ipsec no offload
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we receive the link status message from PF with link up before queues
are actually enabled, it will trigger a TX hang. This fixes the issue
by ignoring a link up message if the VF state is not yet in RUNNING
state.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Client close is overloaded to handle both un-registration and
netdev down event. On netdev down, i40iw client close is called
which unregisters the RDMA dev and this is too destructive
since the netdev is still registered.
Do not call client close/open on netdev down/up events. Instead
disable the PE TCP_ENA flag during a netdev down event. This
blocks all TCP traffic to the RDMA Protocol Engine. On netdev up,
re-enable the flag.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.
If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.
This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.
The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts. By triggering a SW
interrupt, interrupts are forced on. If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.
This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix solves an issue occurring while calling i40e_led_set function
from the driver with "blink" parameter set as TRUE. This call resulted
in Activity LED blinking instead of Link LED, which may lead to errors
in physically identifying the port, since Activity LED may be blinking
for different reasons as well.
Signed-off-by: Michal Kuchta <michal.kuchta@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a host disables and enables a PF device, all the associated
VFs are removed and added back in. It also generates a PFR which in turn
resets all the connected VFs. This behaviour is different from that of
Linux guest on Linux host. Hence we end up in a situation where there's
a PFR and device removal at the same time. And watchdog doesn't have a
clue about this and schedules a reset_task. This patch adds code to send
signal to reset_task that the device is currently being removed.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
flush_schedule_work blocks until completion of all scheduled
work items in global work-queue. This can cause deadlock in some
cases. i40evf_remove() cleans up necessary work items with
cancel_delayed_work_sync and cancel_work_sync. This fix removes
flush_schedule_work call inside i40evf_remove().
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new I40E_NVMUPD_GET_AQ_EVENT state to allow
retrieval of AdminQ events as a result of AdminQ commands sent
to firmware.
Add preservation flags support on X722 devices for NVM update
AdminQ function wrapper. Add new parameter and handling to
nvmupdate admin queue function intended to allow nvmupdate tool
to configure the preservation flags in the AdminQ command.
This is required to implement FlatNVM on X722 devices.
Signed-off-by: Pawel Jablonski <pawel.jablonski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.
The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the support code in place we can now link in the ipsec
offload operations and set the ESP feature flag for the XFRM
subsystem to see.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a simple statistic to count the ipsec offloads.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the skb has a security association referenced in the skb, then
set up the Tx descriptor with the ipsec offload bits. While we're
here, we fix an oddly named field in the context descriptor struct.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the chip sees and decrypts an ipsec offload, set up the skb
sp pointer with the ralated SA info. Since the chip is rude
enough to keep to itself the table index it used for the
decryption, we have to do our own table lookup, using the
hash for speed.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On a chip reset most of the table contents are lost, so must be
restored. This scans the driver's ipsec tables and restores both
the filled and empty table slots to their pre-reset values.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the functions for setting up and removing offloaded SAs (Security
Associations) with the x540 hardware. We set up the callback structure
but we don't yet set the hardware feature bit to be sure the XFRM service
won't actually try to use us for an offload yet.
The software tables are made up to mimic the hardware tables to make it
easier to track what's in the hardware, and the SA table index is used
for the XFRM offload handle. However, there is a hashing field in the
Rx SA tracking that will be used to facilitate faster table searches in
the Rx fast path.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set up the data structures to be used by the ipsec offload.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add in the code for running and stopping the hardware ipsec
encryption/decryption engine. It is good to keep the engine
off when not in use in order to save on the power draw.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a few routines to make access to the ipsec registers just a little
easier, and throw in the beginnings of an initialization.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up the ipsec/macsec descriptor bit definitions to match the rest
of the defines and file organization. Also recognise the bit-definition
overlap in the error mask macro.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pointers txr and rxr are being initialized and a few statements later
are being assigned new values without the original values ever being
read. The initialized values are therefore redundant and can be
removed.
Cleans up clang warnings:
drivers/net/ethernet/broadcom/bnx2.c:5821:28: warning: Value stored to
'txr' during its initialization is never read
drivers/net/ethernet/broadcom/bnx2.c:5822:28: warning: Value stored to
'rxr' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both first_rx_ctx and rx_skb are the head of rx ctx, it not
necessary to use two structure members to statically indicate
the head of rx ctx. So first_rx_ctx is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forgot to update the kernel doc header above sfp_register_upstream()
Fixes: c19bb00070 ("sfp: convert to fwnode")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c:50:34: warning:
symbol 'hw_atl_boards' was not declared. Should it be static?
Fixes: 4948293ff9 ("net: aquantia: Introduce new AQC devices and capabilities")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENOMEM from the aq_ndev_alloc() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 23ee07ad3c ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -EINVAL instead of 0 when num_vfs above
limit_vfs, as done elsewhere in this function.
Fixes: 0dc7862191 ("nfp: handle SR-IOV already enabled when driver is probing")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug that causes _absolute_ rtsym sizes of > 8 bytes (as per symbol
table) to result in incorrect space used during a TLV-based debug dump.
Detail: The size calculation stage calculates the correct size (size of
the rtsym address field == 8), while the dump uses the size in the table
to calculate the TLV size to reserve. Symbols with size <= 8 are handled
OK due to aligning sizes to 8, but including any absolute symbol with
listed size > 8 leads to an ENOSPC error during the dump.
Fixes: da762863ed ("nfp: fix absolute rtsym handling in debug dump")
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to tx ring, xdp_rxq_info is only registered
when !tfile->detached, so we need to avoid calling
xdp_rxq_info_unreg() twice too. The helper tun_cleanup_tx_ring()
already checks for this properly, so it is correct to put
xdp_rxq_info_unreg() just inside there.
Reported-by: syzbot+1c788d7ce0f0888f1d7f@syzkaller.appspotmail.com
Fixes: 8565d26bcb ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the recently added extack support for eBPF offload in the driver.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a pointer to an extack object to nfp_app_xdp_offload() in order to
prepare for extack usage in the nfp driver. Next step will be to forward
this extack pointer to nfp_net_bpf_offload(), once this function is able
to use it for printing error messages.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we no longer localize channel/CPU affiliation within one NUMA
node, num_online_cpus() is used as the number of channel cap, instead of
the number of processors in a NUMA node.
This patch allows a bigger range for tuning the number of channels.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 6221906694 ("be2net: Request RSS capability of Rx interface
depending on number of Rx rings") modified be_update_queues() so the
IFACE (HW representation of the netdevice) is destroyed and then
re-created. This causes a regression because potential promiscuous mode
is not restored properly during be_open() because the driver thinks
that the HW has promiscuous mode already enabled.
Note that Lancer is not affected by this bug because RX-filter flags are
disabled during be_close() for this chipset.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: 6221906694 ("be2net: Request RSS capability of Rx interface depending on number of Rx rings")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spaces were mistakenly used instead of tabs in some of the code related
to reset functionality, which caused checkpatch.pl errors. These were
missed earlier so fixing them now.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T3 devices have different ports on same PCI function,
so using dev_port to identify ports.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom tags inserted by Broadcom switches put a 4 byte header after
the MAC SA and before the EtherType, which may look like some sort of 0
length LLC/SNAP packet (tcpdump and wireshark do think that way). With
ACS enabled in stmmac the packets were truncated to 8 bytes on
reception, whereas clearing this bit allowed normal reception to occur.
In order to make that possible, we need to pass a net_device argument to
the different core_init() functions and we are dependent on the Broadcom
tagger padding packets correctly (which it now does). To be as little
invasive as possible, this is only done for gmac1000 when the network
device is DSA-enabled (netdev_uses_dsa() returns true).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the net status per second, include port speed, total rx/tx packets
and link status. Updating the led status for fiber port.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add led location support for fiber port. The led will keep blinking
when locating.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The manager table is empty by default. If it is not initialized, the
management pkgs like LLDP will be dropped by hardware. Default entries
need to be added to manager table.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds get_regs support for ethtool cmd.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In reset events in which our memory allocations need to be reallocated,
VPD data is being freed, but never reallocated. This can cause issues if
we later attempt to access that memory or reset and attempt to free the
memory. This patch moves the allocation of the VPD data to init_resources
so that it will be symmetrically freed during release resources.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we request an unsupported mtu value, the vnic server will suggest a
different value. Currently we take the suggested value without question
and login with that value. However, the behavior doesn't seem completely
sane as attempting to change the mtu to some specific value will change
the mtu to some completely different value most of the time. This patch
fixes the issue by logging in with the previously used mtu value and
printing an error message saying that the given mtu is unsupported.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using newer backing devices can cause the required padding at the end of
buffer as well as the number of queues to change after a failover.
Since we currently assume that these values never change, after a
failover to a backing device with different capabilities, we can get
errors from the vnic server, attempt to free long term buffers that are
no longer there, or not free long term buffers that should be freed.
This patch resolves the issue by checking whether any of these values
change, and if so perform the necessary re-allocations.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ccfdec9089 ("macsec: Add support for GCM-AES-256 cipher suite")
changed a few values in the uapi headers for MACsec.
Because of existing userspace implementations, we need to preserve the
value of MACSEC_DEFAULT_CIPHER_ID. Not doing that resulted in
wpa_supplicant segfaults when a secure channel was created using the
default cipher. Thus, swap MACSEC_DEFAULT_CIPHER_{ID,ALT} back to their
original values.
Changing the maximum length of the MACSEC_SA_ATTR_KEY attribute is
unnecessary, as the previous value (MACSEC_MAX_KEY_LEN, which was 128B)
is large enough to carry 32-bytes keys. This patch reverts
MACSEC_MAX_KEY_LEN to 128B and restores the old length check on
MACSEC_SA_ATTR_KEY.
Fixes: ccfdec9089 ("macsec: Add support for GCM-AES-256 cipher suite")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When !CONFIG_REGMAP hns throws compiler warnings since
dsaf_read_syscon ignores the return result from regmap_read,
which allows val to be uninitialized.
Fixes: 86897c960b ("net: hns: add syscon operation for dsaf")
Reported-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX8 is a ARMv8 based SoC, that uses the same FEC IP as the
earlier, ARMv7 based, i.MX SoCs. Allow the driver to work on ARM64.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That a kevent could not be scheduled is not an error.
Such handlers must be able to deal with multiple events anyway.
As the successful scheduling of a work is a debug event, make
the failure debug priority, too.
V2: coding style
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Cristian Caravena <caravena@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't change endianness when assigning vlan value in cxgb4_tc_flower
code when processing flow match parameters. The value gets converted
to network order as part of filtering code in set_filter_wr.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ethtype_key = ETH_P_IPV6, set filter type as 1 in cxgb4_tc_flower
code when processing flow match parameters.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main purpose of this patch is adding a way of checking per-queue stats.
It's useful to debug performance problems on multiqueue environment.
$ ethtool -S ens10
NIC statistics:
rx_queue_0_packets: 2090408
rx_queue_0_bytes: 3164825094
rx_queue_1_packets: 2082531
rx_queue_1_bytes: 3152932314
tx_queue_0_packets: 2770841
tx_queue_0_bytes: 4194955474
tx_queue_1_packets: 3084697
tx_queue_1_bytes: 4670196372
This change converts existing per-cpu stats structure into per-queue one.
This should not impact on performance since each queue counter is not
updated concurrently by multiple cpus.
Performance numbers:
- Guest has 2 vcpus and 2 queues
- Guest runs netserver
- Host runs 100-flow super_netperf
Before After Diff
UDP_STREAM 18byte 86.22 87.00 +0.90%
UDP_STREAM 1472byte 4055.27 4042.18 -0.32%
TCP_STREAM 16956.32 16890.63 -0.39%
UDP_RR 178667.11 185862.70 +4.03%
TCP_RR 128473.04 124985.81 -2.71%
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces an alternative way of obtaining resources - via
ACPI tables provided by firmware. Enabling coexistence with the DT
support, in addition to the OF_*->device_*/fwnode_* API replacement,
required following steps to be taken:
* Add mvpp2_acpi_match table
* Omit clock configuration and obtain tclk from the property - in ACPI
world, the firmware is responsible for clock maintenance.
* Disable comphy and syscon handling as they are not available for ACPI.
* Modify way of obtaining interrupts - use newly introduced
fwnode_irq_get() routine
* Until proper MDIO bus and PHY handling with ACPI is established in the
kernel, use only link interrupts feature in the driver. For the RGMII
port it results in depending on GMAC settings done during firmware
stage.
* When booting with ACPI MVPP2_QDIST_MULTI_MODE is picked by
default, as there is no need to keep any kind of the backward
compatibility.
Moreover, a memory region used by mvmdio driver is usually placed in
the middle of the address space of the PP2 network controller.
The MDIO base address is obtained without requesting memory region
(by devm_ioremap() call) in mvmdio.c, later overlapping resources are
requested by the network driver, which is responsible for avoiding
a concurrent access.
In case the MDIO memory region is declared in the ACPI, it can
already appear as 'in-use' in the OS. Because it is overlapped by second
region of the network controller, make sure it is released, before
requesting it again. The care is taken by mvpp2 driver to avoid
concurrent access to this memory region.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OF functions can be used only for the driver using DT.
As a preparation for introducing ACPI support in mvpp2
driver, use struct fwnode_handle in order to obtain
properties from the hardware description.
This patch replaces of_* function with device_*/fwnode_*
where possible in the mvpp2.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'port_count' field of the mvpp2 structure holds an overall amount
of available ports, based on DT nodes status. In order to be prepared
to support other HW description, obtain the value by incrementing it
upon each successful port initialization. This allowed for simplifying
port indexing in the controller's private array, whose size is now not
dynamically allocated, but fixed to MVPP2_MAX_PORTS.
This patch simplifies creating and filling list of enabled ports and
is a part of the preparation for adding ACPI support in the mvpp2 driver.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer pfrm is initialized and then later re-assigned the same
value and hence the second assignment is redundant and can be removed.
Cleans up clang warning:
drivers/net/caif/caif_hsi.c:222:6: warning: Value stored to 'pfrm'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add geneve segmentation offload support of T6 cards.
Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* possible memory leak fix in hwsim
* speed up hwsim
* add hwsim userspace rate control API
* code cleanups
-----BEGIN PGP SIGNATURE-----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=HBMm
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Less than a handful of changes:
* possible memory leak fix in hwsim
* speed up hwsim
* add hwsim userspace rate control API
* code cleanups
====================
A conflict was resolved in mac80211_hwsim.c, mostly of
the simple overlapping changes category. One adding
a rhashtable and another adding a workqueue.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for
all virtual routers") I tried to make sure only used prefix lengths are
present in the LPM tree shared between all virtual routers.
However, this optimization had to be removed in commit a69518cf0b
("mlxsw: spectrum_router: Avoid expensive lookup during route removal"),
since determining the used prefix lengths required us to traverse all
the active virtual routers, which could result in a hung task depending
on the number of VRFs and whether routes were removed due to abort or
not.
Re-introduce the optimization by moving the prefix usage accounting from
the virtual routers to the LPM tree, as this accounting is only used in
order to determine the tree's structure.
To make the sharing of the trees more explicit, the two trees (for IPv4
and IPv6) are stored in the shared router struct and upon the creation
of a virtual router it is immediately bound to both.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next patch will try to optimize the LPM tree and make sure only used
prefix lengths are present, to avoid unnecessary look-ups.
Pass the currently removed FIB node to the unlinking function as its
associated prefix length is a potential candidate for removal from the
tree.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, each FIB (IPv4 / IPv6) in a virtual router holds a prefix
usage that is used to choose a matching LPM tree, but also to check if
the FIB is empty, so that the LPM tree could be unbound.
Next patches will remove the reliance on the per-FIB prefix usage for
LPM tree matching. Keeping it only to check if the FIB is empty is a
waste, since we can use the nodes ({Prefix, Length}) list instead.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warnings:
drivers/net/tun.c:2241:15: error: incompatible types in comparison expression (different address spaces)
Fixes: cd5681d7d8 ("tuntap: rename struct tun_steering_prog to struct tun_prog")
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'hwname' is malloced in hwsim_new_radio_nl() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ff4dd73dd2 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for mirror action. Only one mirror action can be set per rule.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce extension of mlxsw_afa_ops in order to add/del mirroring and
implement the ops for Spectrum.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend SPAN API for ACL case. In case of ACL triggering the MPAR register
shouldn't be configured. This patch also export those helpers for
ACL usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch extends the trap action for mirroring.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, the caller of mlxsw_afa_block_append_counter needed to allocate
counter index by hand. Benefit from the previously introduced resource
infra and counter_index_get/put callbacks, and allocate the counter
index in place where it is needed, inside the action append function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the resource list needs to be used also for other entries different
to fwd_entry_ref, make the list generic. For that purpose, introduce a
resource structure with couple of helpers that the code which need to
store a per-block resource should use.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce extension of mlxsw_afa_ops in order to get/put counter indexes
and implement the ops for Spectrum.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For devices with known capabilities of Fibre media type we now report that
to ethtool.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The detailed reset sequence ensures all HW components are in aligned
state before NIC startup. It also supports cards with signed firmware (RBL)
and checks if their FW is valid.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This defines fw2x operations table and corresponding methods.
Some of the functions are being shared with 1.x firmware
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New AQC cards will have an updated firmware with new binary interface.
This patch extracts firmware specific operations into a separate table
and prepares for the introduction of new fw 2.x and 3.x
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address to check if HW is not dead/hang could be stored in
capabilities, since it is a constant. Change its name to better reflect
the idea.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These ops are not related to HW and are now implemented in pci module.
Thus, remove these ops pointers and implementation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver contained a dead code of maintaining multiple pci port instances.
That will never be used since for each pci function a separate NIC
instance is created.
Simplify this, making pci module only responsible for pci resource
management.
NIC initialization is also simplified accordingly.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes unnecessary structure copying, and prepares the driver for
separate firmware ops table introduction.
We also remove extra copy of capabilities structure (which is const actually)
and also replace it with a const pointer in aq_nic_cfg.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of new AQC devices is going to be released. To support more
flexible capabilities management a number of static caps instances is now
declared. Devices now are mainly differs by supported speeds, but in future
more parameters will be customized. A set of AQC100 devices have
fibre media, not twisted pair - this is also reflected in
new capabilities definitions.
HW level also now directly exports hw_ops for each of A0/B0 hardware.
PCI configuration now uses a device configuration table where each
device ID is explicitly mapped with hardware OPs and capabilities
structures.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New set of aquantia devices has an upgraded hardware (B1).
The hardware interface is identical to B0. The difference will
be in firmware which is incompatible with old one.
Reorganized and removed duplicate speed and devid definitions
Introduced explicit flow control configuration defines
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Or Gerlitz <ogerlitz@mellanox.com>
=======
First six patches of this series further enhances the mlx5 hairpin support.
The first two patches deal with using different hairpin instances
for flows whose packets have different priorities to align with the port
TX QoS model. The next four patches allow us to do HW spreading
of flows over a set of hairpin pairs using RSS. The last two patches
change the driver to also set the size of the HW hairpin queues.
========
Next four patches from Eran Ben Elisha <eranbe@mellanox.com>:
Add more debug data for TX timeout handling, and further enhance and optimize
TX timeout handling upon lost interrupts, which adds a mechanism for explicitly
polling EQ in case of a TX timeout in order to recover from a lost interrupt.
If this is not the case (no pending EQEs), perform a channels full recovery as
usual.
From Kamal Heib <kamalh@mellanox.com>, Two patches to extend the stats group API
to have an update_stats() callback which will be used to fetch the hardware or
software counters data, this will improve the current API and reduce code
duplication.
From Gal Pressman <galp@mellanox.com>, Last patch, Add likely to the common RX checksum
flow.
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaYmJ7AAoJEEg/ir3gV/o+SBIH/2VUS1RPNQfgv1pU2WI78Me3
2Iy8zA2fyx5Ko28Kzu/QljlIUs5/4K0rIjDoT5NpmkLf22lWB3QSqyCkqducdl6J
6kAwZ5kPfA8r1jnhlQfhy5VLhaoNhcHeMafXwP9jSy3BvCYRWTQOsp8fN6fBcSX5
s75DcmqE5ljm5b2Y9pIVkYdzz3usQ9/kq+5MPcZodw3XISuXgv1UPlkon4DdVsXQ
7zf3frQnctfTAepkflWMm8BGUO15a4uYfhrMUyvOFHihtIWA9ILEpUC7qdn3uQ6X
phNA6BRoo9bdo7ZSl8+ZsCi+K4LtyevQTHs7Hn/OMSMvxvDLWZswldu2mbg9xVQ=
=YP/D
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-01-19' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-01-19
From: Or Gerlitz <ogerlitz@mellanox.com>
=======
First six patches of this series further enhances the mlx5 hairpin support.
The first two patches deal with using different hairpin instances
for flows whose packets have different priorities to align with the port
TX QoS model. The next four patches allow us to do HW spreading
of flows over a set of hairpin pairs using RSS. The last two patches
change the driver to also set the size of the HW hairpin queues.
========
Next four patches from Eran Ben Elisha <eranbe@mellanox.com>:
Add more debug data for TX timeout handling, and further enhance and optimize
TX timeout handling upon lost interrupts, which adds a mechanism for explicitly
polling EQ in case of a TX timeout in order to recover from a lost interrupt.
If this is not the case (no pending EQEs), perform a channels full recovery as
usual.
From Kamal Heib <kamalh@mellanox.com>, Two patches to extend the stats group API
to have an update_stats() callback which will be used to fetch the hardware or
software counters data, this will improve the current API and reduce code
duplication.
From Gal Pressman <galp@mellanox.com>, Last patch, Add likely to the common RX checksum
flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously it was possible to interrupt processing stats updates because
they were handled in a work queue. Interrupting the stats updates could
lead to a situation where we backup the control message queue. This patch
moves the stats update processing out of the work queue to be processed as
soon as hardware sends a request.
Reported-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helmut reported a bug about division by zero while
running traffic and doing physical cable pull test.
When the cable unplugged the ppms become zero, so when
dividing the current ppms by the previous ppms in the
next dim iteration there is division by zero.
This patch prevent this division for both ppms and epms.
Fixes: c3164d2fc4 ("net/mlx5e: Added BW check for DIM decision mechanism")
Reported-by: Helmut Grauer <helmut.grauer@de.ibm.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The zeroday builder notices that since Usermode Linux does not
have IO memory, the build fails for them when selecting everything
it can enable.
As the driver is clearly using memory-mapped registers to access
the network adapter, we add depends on HAS_IOMEM to solve this
problem.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-01-19
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) bpf array map HW offload, from Jakub.
2) support for bpf_get_next_key() for LPM map, from Yonghong.
3) test_verifier now runs loaded programs, from Alexei.
4) xdp cpumap monitoring, from Jesper.
5) variety of tests, cleanups and small x64 JIT optimization, from Daniel.
6) user space can now retrieve HW JITed program, from Jiong.
Note there is a minor conflict between Russell's arm32 JIT fixes
and removal of bpf_jit_enable variable by Daniel which should
be resolved by keeping Russell's comment and removing that variable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
We only register the ATU and VTU irq when we have a chip level IRQ.
In the error path, we should only attempt to remove the ATU and VTU
irq if we also have a chip level IRQ.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a cut/paste error. When irq_find_mapping() returns an error for
the ATU or VTU interrupt, return that error, not the value of
chip->device_irq.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization the driver checks whether the flashed FW image
suits its requirements by checking that it's sufficiently new.
However, there's only a weak backward compatibility scheme that is
actually guaranteed by the FW, so driver must also upper bound the
version to prevent compatibility issues between current driver and some
possible future fw.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF firmware currently exposes IRQ moderation capability.
The driver will make use of it by default, inserting 50 usec
delay to every control message exchange. This cuts the number
of messages per second we can exchange by almost half.
None of the other capabilities make much sense for BPF control
vNIC, either. Disable them all.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most vNIC capabilities are netdev related. It makes no sense
to initialize them and waste FW resources. Some are even
counter-productive, like IRQ moderation, which will slow
down exchange of control messages.
Add to nfp_app a mask of enabled control vNIC capabilities
for apps to use. Make flower and BPF enable all capabilities
for now. No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_net_init() is a little long and we are about to add more
code to reading capabilties. Move the capability reading,
parsing and validating out. Only actual initialization
will stay in nfp_net_init().
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow specifying alternative vNIC mailbox location in TLV caps.
This way we can size the mailbox to the needs and not necessarily
waste 512B of ctrl memory space.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCIe island clock frequency is used when converting coalescing
parameters from usecs to NFP timestamps. Most chips don't run
at 1200MHz, allow FW to provide us with the real frequency.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP is entirely programmable, including the PCI data interface.
Using a fixed control BAR layout certainly makes implementations
easier, but require careful considerations when space is allocated.
Once BAR area is allocated to one feature nothing else can use it.
Allocating space statically also requires it to be sized upfront,
which leads to either unnecessary limitation or wastage.
We currently have a 32bit capability word defined which tells drivers
which application FW features are supported. Most of the bits
are exhausted. The same bits are also reused for enabling specific
features. Bulk of capabilities don't have a need for an enable bit,
however, leading to confusion and wastage.
TLVs seems like a better fit for expressing capabilities of applications
running on programmable hardware.
This patch leaves the front of the BAR as is, and declares a TLV
capability start at offset 0x58. Most of the space up to 0x0d90
is already allocated, but the used space can be wrapped with RESERVED
TLVs. E.g.:
Address Type Length
0x0058 RESERVED 0xe00 /* Wrap basic structures */
0x0e5c FEATURE_A 0x004
0x0e64 FEATURE_B 0x004
0x0e6c RESERVED 0x990 /* Wrap qeueue stats */
0x1800 FEATURE_C 0x100
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver app matching loaded FW is not found users are faced with:
nfp: failed to find app with ID 0x%02x
This message does not properly explain that matching driver code is
either not built into the driver or the driver is too old.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Representors are grouped in sets by type. Currently the whole
sets are under RCU protection, but individual representor pointers
are not. This causes some inconveniences when representors have
to be destroyed, because we have to allocate new sets to remove
any representors. Protect the individual pointers with RCU.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The write side of repr tables is always done under pf->lock.
Add a helper to dereference repr table pointers under protection
of that lock.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink used to have two global locks: devlink lock and port lock,
our lock ordering looked like this:
devlink lock -> driver's pf->lock -> devlink port lock
After recent changes port lock was replaced with per-instance
lock. Unfortunately, new per-instance lock is taken on most
operations now. This means we can only grab the pf->lock from
the port split/unsplit ops. Lock ordering looks like this:
devlink lock -> driver's pf->lock -> devlink instance lock
Since we can't take pf->lock from most devlink ops, make sure
nfp_apps are prepared to service them as soon as devlink is
registered. Locking the pf must be pushed down after
nfp_app_init() callback.
The init order looks like this:
nfp_app_init
devlink_register
nfp_app_start
netdev/port_register
As soon as app_init is done nfp_apps must be ready to service
devlink-related callbacks. apps can only register their own
devlink objects from nfp_app_start.
Fixes: 2406e7e546 ("devlink: Add per devlink instance lock")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP app is currently shut down as soon as all the vNICs are gone.
This means we can't depend on the app existing throughout the
lifetime of the device. Free the app only from PCI remove path.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the helpers for accessing 4 or 8 byte values over
the CPP bus return the length of IO on success. If the IO
was short caller has to deal with error handling. The short
IO for 4/8B values is completely impractical. Make the
helpers return an error if full access was not possible.
Fix the few places which are actually dealing with errors
correctly, most call sites already only deal with negative
return codes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the packets return true for is_last_ethertype_ip, surround it
with likely compiler hint.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Extend the stats group API to have an update_stats() callback which
will be used to fetch the hardware or software counters data.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Merge the per priority traffic and pfc groups into one group, because
both groups share the same update_stats() callback which will be
introduced in the upcoming patch.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add per-channel counter ch#_eq_rearm to monitor how many lost interrupt
recovery actions happened upon TX timeouts.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Up until this patch, on every TX timeout we would try to do channels
recovery. However, in case of a lost interrupt for an EQ, the channel
associated to it cannot be recovered if reopened as it would never get
another interrupt on sent/received traffic, and eventually ends up with
another TX timeout (Restarting the EQ is not part of channel recovery).
This patch adds a mechanism for explicitly polling EQ in case of a TX
timeout in order to recover from a lost interrupt. If this is not the
case (no pending EQEs), perform a channels full recovery as usual.
Once a lost EQE is recovered, it triggers the NAPI to run and handle all
pending completions. This will free some budget in the bql (via calling
netdev_tx_completed_queue) or by clearing pending TXWQEs and waking up
the queue. One of the above actions will move the queue to be ready for
transmit again.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When TX timeout occurs, EQ consumer index and irqn can help in debug for
understanding the SW state of EQ. Add them to the logger prints for the
relevant EQ only.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When driver callback for TX timeout is being called, it handles all
stopped xmit queues (not only the ones which their timeout expired).
Add usecs since last transmit to TX timeout logs per send queue in order
to monitor if the queue timeout expired.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For a given hairpin packet buffer size, different queue sizes
(values of log_hairpin_num_packets) determine how the data is broken
to strides on the RQ. Currently the chosen value is set to 64B strides.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allow to specify the size of the hairpin queues along with the
packet buffer data size from the core setup code.
If the driver doesn't provide this, the FW applies proper value that
matches the provided data size and a FW chosen RQ stride size.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support RSS for hairpin traffic. We create multiple hairpin RQ/SQ pairs
and RSS TTC table per hairpin instance and steer the related flows
through that table so they are spread between the pairs.
We open one pair per 50Gbs link speed, for all speeds <= 50Gbs, there
is one pair and no RSS while for 100Gbs ports two RSSed pairs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enhance the hairpin setup code at the core to support a set of N
(RQ,SQ) pairs. This will be later used by the caller to set RSS
spreading among the different RQs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This will allow to be able and set TC rule whose steering dest is
RSS TTC steering table.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to use RSS for hairpin, we refactor the code that deals with
setup of the TTC steering tables. This is done using an interim ttc
params object that has the flow table attributes, TIR numbers, etc.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As part of the QoS model, on xmit, the HW mandates that all packets going
through a given SQ have the same priority. To align hairpin SQs with that,
we use the priority given as part of the matching for the hairpin hash key.
This ensures that flows/packets mapped to different HW priorities will
go through different hairpin instances. If no priority is given for
matching, we treat that as an 8th priority, this is in order not to
harm cases where priority is specified.
Only the PCP priority trust model is supported.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The peer vhca id spans less bits vs the ifindex and can
well serve for the hairpin hash key, move to use that.
This is a pre-step to put more info into the hairpin hash
key in downstream patch while keeping it at 32 bits.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
on T6, IPv6 filter would occupy 2 tids instead of 4.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use zlib deflate to compress firmware dump. Collect and compress
as much firmware dump as possible into a 32 MB buffer.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update firmware dump collection logic to use compression when available.
Let collection logic attempt to do compression, instead of returning out
of memory early.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
