Add the definition for ICL power wells and their mapping to power
domains. On ICL there are 3 power well control registers, we'll select
the correct one based on higher bits of the power well ID. The offset
for the control and status flags within this register is based on the
lower bits of the ID as on older platforms.
As the DC state programming is also the same as on old platforms we can
reuse the corresponding helpers. For this we mark here the DC-off power
well as shared among multiple platforms.
Other than the above the delta between old platforms and ICL:
- Pipe C has its own power well, so we can save some additional power in the
pipe A+B and (non-eDP) pipe A configurations.
- Power wells for port E/F DDI/AUX IO and Thunderbolt 1-4 AUX IO
v2:
- Rebase on drm-tip after prep patch for this was merged there as
requested by Paulo.
- Actually add the new AUX and DDI power well control regs (Rakshmi)
v3:
- Fix power well register names in code comments
- Add TBT AUX->power well 3 dependency
v4:
- Rebase
v5:
- Detach AUX power wells from the INIT power domain. These power wells
can only be enabled in a TC/TBT connected state and otherwise not
needed during driver initialization.
v6:
- Use _MMIO_PORT(...) instead _MMIO(_PICK(...)) (Paulo)
Fix checkpatch warnings.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com> (v1)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626142232.22361-1-imre.deak@intel.com
So far we got an AUX power domain reference only for the duration of DP
AUX transfers. However, the following suggests that we also need these
for main link functionality:
- The specification doesn't state whether it's needed or not for main
link functionality, but suggests that these power wells need to be
enabled already during display core initialization (Sequences to
Initialize Display).
- For PSR we need to keep the AUX power well enabled.
- On ICL combo PHY ports (non-TC) the AUX power well is needed for
link training too: while the port is enabled with a DP link training
test pattern trying to toggle the AUX power well will time out.
- On ICL MG PHY ports (TC) the AUX power well is needed also for main
link functionality (both in DP and HDMI modes).
- Windows enables these power wells both for main and AUX lane
functionality.
Based on the above take an AUX power reference for main link
functionality too. This makes a difference only on GEN10+ (GLK+)
platforms, where we have separate port specific AUX power wells.
For PSR we still need to distinguish between port A and the other
ports, since on port A DC states must stay enabled for main link
functionality, but DC states must be disabled for driver initiated
AUX transfers. So re-use the corresponding helper from intel_psr.c.
Since we take now a reference for main link functionality on all DP
ports we can forgo taking the separate power ref for PSR functionality.
v2:
- Make sure DC states stay enabled when taking the ref on port A.
(Ville)
v3: (Ville)
- Fix comment about logic for encoders without a crtc state and
add FIXME note for a simplification to avoid calling get_power_domains
in such cases.
- Use intel_crtc_has_dp_encoder() instead !intel_crtc_has_type(HDMI).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Clarified code comments in intel_ddi_main_link_aux_domain() and
intel_ddi_get_power_domains() (Imre)]
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621184449.26634-1-imre.deak@intel.com
Add support for DP_AUX_E. Here we also introduce the bits for the AUX
power well E, however ICL power well support is still not enabled yet,
so the power well is not used.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612002512.29783-2-paulo.r.zanoni@intel.com
Add documentation to gen9_set_dc_state() on what enabling a given DC
state means and at what point HW/DMC actually enters/exits these states.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180417113147.25120-1-imre.deak@intel.com
ICL has two slices of DBuf, each slice of size 1024 blocks.
We should not always enable slice-2. It should be enabled only if
display total required BW is > 12GBps OR more than 1 pipes are enabled.
Changes since V1:
- typecast total_data_rate to u64 before multiplication to solve any
possible overflow (Rodrigo)
- fix where skl_wm_get_hw_state was memsetting ddb, resulting
enabled_slices to become zero
- Fix the logic of calculating ddb_size
Changes since V2:
- If no-crtc is part of commit required_slices will have value "0",
don't try to disable DBuf slice.
Changes since V3:
- Create a generic helper to enable/disable slice
- don't return early if total_data_rate is 0, it may be cursor only
commit, or atomic modeset without any plane.
Changes since V4:
- Solve checkpatch warnings
- use kernel types u8/u64 instead of uint8_t/uint64_t
Changes since V5:
- Rebase
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-3-mahesh1.kumar@intel.com
This patch adds support to start tracking status of DBUF slices.
This is foundation to introduce support for enabling/disabling second
DBUF slice dynamically for ICL.
Changes Since V1:
- use kernel type u8 over uint8_t
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-2-mahesh1.kumar@intel.com
One is outright unused, other can be made static.
Drive-by cleanup while accidentally reading dc code.
Cc: Imre Deak <imre.deak@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180417100225.12286-1-daniel.vetter@ffwll.ch
The DMC FW specific part of display WA#1183 is supposed to be enabled
whenever enabling DC5 or DC6, so move it to the DC6 enable function
from the DC6 disable function.
I noticed this after Daniel's patch to remove the unused
skl_disable_dc6() function.
Fixes: 53421c2fe9 ("drm/i915: Apply Display WA #1183 on skl, kbl, and cfl")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180419155109.29451-1-imre.deak@intel.com
PSR on CNL requires AUX IO wells to be kept on and the existing AUX domain
for AUX-A enables DC_OFF well too. This is not required, so add a new
AUX_IO_A domain for AUX-A to allow DC states to remain enabled. Other AUX
channels re-use the existing AUX domains.
v4: Reword comment (Rodrigo and Ville)
Rename _get and _put functions to include aux_io substring(Rodrigo)
Remove unnecessary diff that got included.
v3: Extract aux domain selection into a function (Ville)
v2: Add AUX IO domain only for AUX-A
Rebased on top of Ville's AUX series.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-1-dhinakaran.pandiyan@intel.com
This patch initializes MBus during display initialization.
Changes since V2 (from Paulo):
- Don't forget to remove the WARN_ON(1) call.
Changes since V1:
- Rebase to use function like Macros
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-6-paulo.r.zanoni@intel.com
ICL has 2 slices of DBuf, enable both the slices during display init.
Ideally we should only enable the second slice when needed in order to
save power, but while we're not there yet, adopt the simpler solution
to keep us bug-free.
v2 (from Paulo):
- Add the TODO comment.
- Reorganize where things are defined.
- Fix indentation.
- Remove unnecessary POSTING_READ() calls.
- Improve the commit message.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-5-paulo.r.zanoni@intel.com
This code is similar enough to the CNL code that I considered just
adding ICL support to the CNL function, but I think it's still
different enough, and having a function specific to ICL allows us to
more easily adapt code in case the spec changes more later.
We're still missing the power wells and the mbus code, so leave those
pieces with a FIXME comment while they're not here yet.
v2: Don't use _PICK, don't WARN_ON(1), don't forget the chicken bits.
v3: Use _MMIO_PORT() (Ville).
Reviewed-by: James Ausmus <james.ausmus@intel.com> (v2)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-4-paulo.r.zanoni@intel.com
On ICL we have two sets of registers: one for port A and another for
port B. The set of port A registers is the same as the CNL registers.
Since the procmon table on ICL is the same we want to reuse the CNL
function. To do that we add a port argument and make CNL always call
the function passing port A. This way, we'll be able to easily reuse
the function on ICL when we add icl_display_core_init().
v2: Don't use _PICK() when you can use a ternary operator.
v3: Don't use a ternary operation when you can use _MMIO_PORT (Ville).
Add an extra comment about why we're passing PORT_A (James).
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-2-paulo.r.zanoni@intel.com
Now let's finish the Port-F support by adding the
proper port F detection, irq and power well support.
v2: Rebase
v3: Use BIT_ULL
v4: Cover missed case on ddi init.
v5: Update commit message.
v6: Rebase on top of display headers rework.
v7: Squash power-well handling related to DDI F to this
patch to avoid warns as pointed out by DK.
v8: Introduce DDI_F_LANES to PG2. (DK)
v9: Squash in the PORT_F case for enabling DP MST encoder. (DK)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-9-rodrigo.vivi@intel.com
On some Cannonlake SKUs we have a dedicated Aux for port F,
that is only the full split between port A and port E.
There is still no Aux E for Port E, as in previous platforms,
because port_E still means shared lanes with port A.
v2: Rebase.
v3: Add couple missed PORT_F cases on intel_dp.
v4: Rebase and fix commit message.
v5: Squash Imre's "drm/i915: Add missing AUX_F power well string"
v6: Rebase on top of display headers rework.
v7: s/IS_CANNONLAKE/IS_CNL_WITH_PORT_F (DK)
v8: Fix Aux bits for Port F (DK)
v9: Fix VBT definition of Port F (DK).
v10: Squash power well addition to this patch to avoid
warns as pointed by DK.
v11: Clean up squashed commit message. (David)
v12: Remove unnecessary handling for older platforms (DK)
Adding AUX_F to PG2 following other existent ones. (DK)
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-2-rodrigo.vivi@intel.com
Display WA #1178 is meant to fix Aux channel voltage swing too low with
some type C dongles. Although it is for type C, HW engineers reported
that it can be applied to all external ports even if they are not going
to type C.
For CNL we apply the workaround every time Aux B, C and D are powering
up since they will lose the configuration when powered down.
v2: Use common tag for WA
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171128220553.22435-1-lucas.demarchi@intel.com
With firmware 1.07 having fixed the state corruption issue, we can enable
the headless GT performance workaround for CNL as well. (Equivalent to
b68763741a ("drm/i915: Restore GT performance in headless mode with DMC
loaded") on other affected platforms.)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100572
Testcase: igt/gem_exec_nop/headless
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111082417.795-1-tvrtko.ursulin@linux.intel.com
Display WA #1183 was recently added to workaround
"Failures when enabling DPLL0 with eDP link rate 2.16
or 4.32 GHz and CD clock frequency 308.57 or 617.14 MHz
(CDCLK_CTL CD Frequency Select 10b or 11b) used in this
enabling or in previous enabling."
This workaround was designed to minimize the impact only
to save the bad case with that link rates. But HW engineers
indicated that it should be safe to apply broadly, although
they were expecting the DPLL0 link rate to be unchanged on
runtime.
We need to cover 2 cases: when we are in fact enabling DPLL0
and when we are just changing the frequency with small
differences.
This is based on previous patch by Rodrigo Vivi with suggestions
from Ville Syrjälä.
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171204232210.4958-1-lucas.demarchi@intel.com
It seems that the DMC likes to transition between the DC states a lot when
there are no connected displays (no active power domains) during command
submission.
This activity on DC states has a negative impact on the performance of the
chip with huge latencies observed in the interrupt handlers and elsewhere.
Simple tests like igt/gem_latency -n 0 are slowed down by a factor of
eight.
Work around it by introducing a new power domain named,
POWER_DOMAIN_GT_IRQ, associtated with the "DC off" power well, which is
held for the duration of command submission activity.
CNL has the same problem which will be addressed as a follow-up. Doing
that requires a fix for a DC6 context corruption problem in the CNL DMC
firmware which is yet to be released.
v2:
* Add commit text as comment in i915_gem_mark_busy. (Chris Wilson)
* Protect macro body with braces. (Jani Nikula)
v3:
* Add dedicated power domain for clarity. (Chris, Imre)
* Commit message and comment text updates.
* Apply to all big-core GEN9 parts apart for Skylake which is pending DMC
firmware release.
v4:
* Power domain should be inner to device runtime pm. (Chris)
* Simplify NEEDS_CSR_GT_PERF_WA macro. (Chris)
* Handle async DMC loading by moving the GT_IRQ power domain logic into
intel_runtime_pm. (Daniel, Chris)
* Include small core GEN9 as well. (Imre)
v5
* Special handling for async DMC load is not needed since on failure the
power domain reference is kept permanently taken. (Imre)
v6:
* Drop the NEEDS_CSR_GT_PERF_WA macro since all firmwares have now been
deployed. (Imre, Chris)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100572
Testcase: igt/gem_exec_nop/headless
Cc: Imre Deak <imre.deak@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v5)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[Imre: Add note about applying the WA on CNL as a follow-up]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171205132854.26380-1-tvrtko.ursulin@linux.intel.com
For CNL we'll need to start considering the port clocks when we select
the voltage level for the system agent. To that end start tracking the
voltage in the cdclk state (since that already has to adjust it).
v2: s/voltage/voltage_level/ (Rodrigo)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-3-ville.syrjala@linux.intel.com
In order to separate GT PM related functionality into new structure
we are updating rps structure. hw_lock in it is used for display
related PCU communication too hence move it to dev_priv.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-8-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-7-chris@chris-wilson.co.uk
Not all compilers are able to determine that pg is guarded by wait_fuses
and so may think that pg is used uninitialized.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: b2891eb253 ("drm/i915/hsw+: Add has_fuses power well attribute")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171002100416.25865-1-chris@chris-wilson.co.uk
Reviewed-by: Imre Deak <imre.deak@intel.com>
Our global struct with params is named exactly the same way
as new preferred name for the drm_i915_private function parameter.
To avoid such name reuse lets use different name for the global.
v5: pure rename
v6: fix
Credits-to: Coccinelle
@@
identifier n;
@@
(
- i915.n
+ i915_modparams.n
)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170919193846.38060-1-michal.wajdeczko@intel.com
Move the part that reads the table and sets registers based on the
table to its own function.
v2: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170822000356.17330-2-rodrigo.vivi@intel.com
Make it a little less magical and a little simpler and more hardcoded
so we don't end up with an array that's composed mostly of empty
entries.
v2: Add an enum for the voltage+register values (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170822000356.17330-1-rodrigo.vivi@intel.com
Future platforms increase the number of power wells which require
additional control registers. A convenient way to select the correct
register is to use the high bits of the power well ID as index. This
patch only prepares for this, while upcoming platform enabling patches
will add the actual new power well IDs and corresponding power well
control registers.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170814151530.24154-2-imre.deak@intel.com
GCC 4.4 can't cope with anonymous union initializers which seems to be a
bug in that version (see the Reference) and is fixed since GCC version
4.6. A workaround which is also used elsewhere in the kernel for the
same purpose is to wrap the initialization in curly braces, so do the
same here.
Fixes: b5565a2efc ("drm/i915/bxt, glk: Give a proper name to the power well struct phy field")
Reference: http://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170814151530.24154-1-imre.deak@intel.com
DDI_E is not supported on CNL-U and CNL-Y
When adding the initial support we noticed DDI_E wasn't supported
and removed it on v4 and v5 of that patch.
However for some reason I missed or put back these 2 chunks.
Time to clean it up to avoid later confusion.
Fixes: 8bcd3dd417 ("drm/i915/cnl: Add power wells for CNL")
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170808193237.17410-1-rodrigo.vivi@intel.com
* Don't define it twice.
* Define MSBs first, like the rest of i915_reg.h.
* Add CNL_ prefix to the bit that arrived in CNL.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170714175228.27019-1-paulo.r.zanoni@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the previous refactorings the HSW/BDW and GEN9+ power well helpers
are practically identical, so use the HSW power well helpers for GEN9+
too. This means using the HSW power well ops instead of the SKL one and
setting the irq_pipe_mask, has_vga and has_fuses attributes as needed.
v2:
- Rebased on v2 of patch 15.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-7-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pattern of a power well backing a set of fuses whose initialization
we need to wait for during power well enabling is common to all GEN9+
platforms. Adding support for this to the HSW power well enable helper
allows us to use the HSW/BDW power well code for GEN9+ as well in a
follow-up patch.
v2:
- Use an enum for power gates instead of raw numbers. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-6-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly to GEN9+ waiting for the power well disabled state is a safer
option and also provides diagnostic info if the disabling didn't succeed
or the power well was forced on by an external requester. While at it
also use the existing GEN9+ helper to wait for the enabled state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-15-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pattern of a power well backing a set of pipe IRQ or VGA
functionality applies to all HSW+ platforms. Using power well attributes
instead of platform checks to decide whether to init/reset pipe IRQs and
VGA correspondingly is cleaner and it allows us to unify the HSW/BDW and
GEN9+ power well code in follow-up patches.
Also use u8 for pipe_mask in related helpers to match the type in the
power well struct.
v2:
- Use u8 instead of u32 for irq_pipe_mask. (Ville)
v3:
- Use u8 for pipe_mask in related helpers too for clarity.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170712155413.29839-1-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although on HSW/BDW there is only a single display global power well,
it's programmed the same way as other GEN9+ power wells. This also
means we can get at the HSW/BDW request and status flags the same way
it's done on GEN9+ by assigning the corresponding HSW/BDW power well ID.
This ID was assigned in a recent patch, so we can now switch to using
the same macros everywhere on HSW+.
Updating the HSW power well control register with RMW is not strictly
necessary, but this will allow us to use the same code for GEN9+.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-13-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can reduce the code indentation by splitting the set helper to
separate enable/disable helpers. This also allows us to unify the
HSW/BDW and GEN9+ power well ops in follow-up patches, which introduces
some differences between the enable and disable helpers.
While at it also remove the redundant enable/disable debug messages,
the same info is printed already elsewhere.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-12-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly to the GEN9 power well toggling, saving an occasional extra
MMIO write is not worth the code complexity, let's simplify things.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-11-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we enable/disable a power well only if it wasn't already
enabled/disabled respectively. The only reason for this I can think of
is to save the extra MMIO writes. Since the HW state matches the power
well's usage counter most of the time the overhead due to these MMIOs is
insignificant. Let's simplify the code by making the writes
unconditional.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-10-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We check already for power wells that are unexpectedly on (or forced on)
during power well disabling. Those checks also account for other
power well requesters like KVMR or DEBUG. As such this check is
redundant, let's remove it to simplify things.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-9-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow-up patches will add new fields to the i915_power_well struct that
are specific to the hsw_power_well_ops helpers. Prepare for this by
changing the generic 'data' field to a union of platform specific
structs.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-8-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check that all the power well IDs are unique on the given platform.
v2:
- Fix using BIT_ULL() instead of BIT() for 64 bit mask.
v3:
- Move the check to a separate function. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-4-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add an ID for the HSW/BDW global display power well for consistency. The
ID is selected so that it can be used to get at the HW request and
status flags with the corresponding GEN9+ macros. Unifying the HSW/BDW
and GEN9+ versions of these macros and the power well ops using them
will be done in follow-up patches.
v2:
- Rebased on v2 of patch 2.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-3-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the I830 power well ID assignment explicit for consistency.
v2:
- s/GEN2/I830/ in the comment, since other GEN2s don't have the power
well. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-2-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
