As long as the connector was zeroed during allocation calling
intel_panel_fini() is safe even if we haven't initialized
the panel struct explicitly. So let's drop the useless eDP
check from dp connector destruction.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181008134641.24868-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently we destroy the backlight during connector unregistration.
That means the final modeset performed by drm_atomic_helper_shutdown()
will leave the backlight on. We don't want that so let's just move
intel_panel_destroy_backlight() into intel_panel_fini() which gets
called during connector destuction.
We still unregister the user visible backlight device during connector
unregistration.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181008134641.24868-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106386
Incorrect TDL's SSP address shift in SARB for 16:6 & 18:8 modes.
Disable the Sampler state prefetch functionality in the SARB by
programming 0xB000[30] to '1'. This is to be done at boot time
and the feature must remain disabled permanently.
Fixes flaky tex-mip-level-selection* piglit tests with Mesa i965
driver.
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004182939.7668-6-radhakrishna.sripada@intel.com
Shader feature to prefetch binding tables does not support 16:6 18:8 BTP
formats. Enabling fault handling could result in hangs with faults.
Disabling demand prefetch would disable binding table prefetch.
V2: Fix the stepping rivision to B0(Mika)
References: HSDES#1406609255, HSDES#1406573985
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004182939.7668-5-radhakrishna.sripada@intel.com
s/crtc/crtc_state/ for the kernel doc as well as the params.
Fixes: 65c307fd08 ("drm/i915: Make shared dpll functions take crtc_state, v3.")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181008104808.17457-1-chris@chris-wilson.co.uk
Use a more familiar naming pattern for our variables in the sprite plane
init function.
v2: Drop the redundant 'plane' from plane_formats and num_planes_formats
too
v3: Rebase due to ->max_stride() and ->check_plane() changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-11-ville.syrjala@linux.intel.com
There's not much point in following the primary vs. sprite split
for the SKL+ universal plane init code. The only difference is
of our own doing in the form of the .check_plane(). Let's make
a small exception for that little detail and otherwise share
the same code to initialize all the universal planes.
Eventually we should eliminate the mess around .check_plane()
as well, but for now let's be happy with some code reduction.
v2: Remember to set up plane->has_fbc
Make skl_plane_has_ccs() static
v3: Rebase due to NV12, rename some variables
v4: Don't leave the color_encoding/range props behind
v5: Rebase dur to blend properties, skl_plane_max_stride() and
skl_plane_check()
v6: Make skl_update_plane() static
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-10-ville.syrjala@linux.intel.com
Pull the common plane+plane_state allocation into a small helper.
Reduces the amount of boilerplate in the plane initialization
functions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-9-ville.syrjala@linux.intel.com
No point in having each caller of intel_create_plane_state() initialize
the scaler_id to -1. Instead just do it in intel_create_plane_state().
Previously we left scaler_id at 0 for pre-SKL platforms, but I can't
see how initializing it to -1 always would cause any harm.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-8-ville.syrjala@linux.intel.com
All SKL+ universal planes support the same set of formats (with the
exception of NV12 which we don't expose yet). Make the format lists
for primary and sprites the same.
And make the format list const while at it.
v2: Deal with the "planar" format list as well
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-7-ville.syrjala@linux.intel.com
Plane scaling is not supported with specific pixel formats. Disallow
plane scaling when such a format is used. Currently the only such
pixel format we expose is C8, but in case we add more in the future
let's make it easy to deal with them.
v2: Redo due to plane_check() refactoring
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-6-ville.syrjala@linux.intel.com
All CNL universal planes support horizontal mirroring. Currently
we expose the capability only for the primary plane. Expose it
for the overlay planes as well.
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-5-ville.syrjala@linux.intel.com
We're currently not providing the possible_crtcs mask to
drm_universal_plane_init() for primary/cursor planes. While that does
work on account of drm_crtc_init_with_planes() filling those up
for us, it's inconsisten with what we're doing for sprite planes.
Let's just always pass the possible_crtcs bitmask to
drm_universal_plane_init(). This does assume that crtc->index
== pipe. But we're already making that assumption elsewhere so
it doesn't seem like a very big sin here.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-3-ville.syrjala@linux.intel.com
ALPM is a requirement and we don't need to keep it's cached, what
were done in commit 97c9de66ca
("drm/i915/psr: Fix ALPM cap check for PSR2") but the alpm was not
removed from i915_psr.
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003205031.32474-7-jose.souza@intel.com
This WA also works fine for PSR2, triggering a selective update when
possible.
Acked-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003205031.32474-4-jose.souza@intel.com
ICL spec states that this bit is now reserved.
Bspec: 7722
v2(Dhinakaran and Jani):
- instead of remove bit in gen11 now only setting if if gen < 11
- changed commit title
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003205031.32474-2-jose.souza@intel.com
Now both PSR and PSR2 have the same exit mask, so let's share then
instead of have the same code 2 times.
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003205031.32474-1-jose.souza@intel.com
No functional change. But just a minor change to keep
up with Spec, since it has changed since commit c3cc39c539
("drm/i915/icl: program mbus during pipe enable")
The instructions previously said to program pipe's
B credit = 24 / number of pipes, which is 8 for ICL.
Now the spec gives us direct values independent of number
of pipes. Let's keep in sync.
Also just a reorder on fields to make easier to compare
against spec's sequence: A -> BW -> B.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004151814.6054-1-rodrigo.vivi@intel.com
Amber Lake used the same gen graphics as Kaby Lake. Kernel driver
should configure KBL's DDI buffer setting for AML ULX as well.
So far, driver would load DDI translation table that used for
KBL H/S platform and apply it on AML devices. But AML is belong to
ULX series. This change will lead driver to apply KBL-Y's DDI table
for AML devices to avoid unexpected eDP/DP signal quality issue.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1538034499-31256-2-git-send-email-shawn.c.lee@intel.com
According to patch "drm/i915/aml: Introducing Amber Lake platform"
(e364672477). Add a new marco for AML ULX GT2 devices.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1538034499-31256-1-git-send-email-shawn.c.lee@intel.com
Sprite enable on ILK-IVB may take two frames to complete
when the hardware is in big FIFO mode (LP1+). That is
not entirely great as it means the sprite enable may
actually happen one frame after we've already signalled
flip completion. At the very least crc checks may fail
due to the sprite not yet being visible when we expect it.
We already have code to deal with big FIFO mode when it
comes to the sprite scaling on IVB
(WaCxSRDisabledForSpriteScaling:ivb). Let's extend that
workaround to kick in whenever the sprite is in the process
of being enabled. Also ILK/SNB bspec has some notes to
indicate that we should most likely also do the sprite
scaling w/a on all three platforms, so let's do that as well.
Pretty easy to reproduce on SNB/IVB. ILK has proved more
elusive, but let's trust the spec and include it as well.
v2: Make sure the pipe is active before the vblank wait
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Testcase: igt/kms_plane/pixel-format-pipe-*-planes
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107749
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20181004121527.30249-1-ville.syrjala@linux.intel.com
Fixing chv_set_phy_signal_level() still requires too many levels of
indirection to pass crtc_state along, but chv_data_lane_soft_reset()
already has a crtc_state we can use.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004094604.2646-13-maarten.lankhorst@linux.intel.com
fbdev init shouldn't race with userspace since it's called from
intel_modeset_init, so it's safe to dereference crtc->state and
assume nothing changed yet.
At least not more harmful than crtc->config.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004094604.2646-11-maarten.lankhorst@linux.intel.com
Do not rely on crtc->config any more. Remove the assertion from
ibx_pch_dpll_disable, because we the dpll state tracking should
already handle this case correctly.
Changes since v1:
- Fixup accidental early return in intel_prepare_shared_dpll, oops!
Changes since v2:
- Don't use the freed crtc_state in intel_crtc_disable_noatomic()
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005095244.1324-1-maarten.lankhorst@linux.intel.com
Instead of passing crtc and dereferencing crtc->config,
passs the correct crtc_state and obtain the crtc pointer from there.
Changes since v1:
- Move vlv/chv changes and i9xx_set_pll_dividers changes
from crtc_enable/disable patches to here.
- Add commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004094604.2646-7-maarten.lankhorst@linux.intel.com
One more user of crtc->config down. :)
Changes since v1:
- Constify crtc_state
- int pipe -> enum pipe pipe
- Move i9xx_set_pipeconf declaration to the other pipeconf declarations.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004094604.2646-2-maarten.lankhorst@linux.intel.com
Earlier, we reasoned that having idled the gpu under mempressure, that
would be a good time to trim our request slabs in order to perform the
next request allocation. We have stopped performing the global operation
on the device (no idling) and wish to make the allocation failure
handling more local, so out with the global barrier that may take a long
time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005080300.9908-2-chris@chris-wilson.co.uk
Before we can reset the seqno, we have to be sure the engines are idle.
In debugfs/i915_drop_caches_set, we do wait_for_idle but allow ourselves
to be interrupted. We should only proceed to reset the seqno then if we
were not interrupted, and so also avoid overwriting the error status.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108133
Fixes: 6b048706f4 ("drm/i915: Forcibly flush unwanted requests in drop-caches")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004082119.24970-1-chris@chris-wilson.co.uk
Print the plane hw state readout results in the common format
we already use for pipes and encoders. Also print some clearer
debug messages when we disable planes during the early phases
of state readout/sanitization.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003145052.4633-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we decide that a plane is attached to the wrong pipe we try
to turn off said plane. However we are passing around the crtc we
think that the plane is supposed to be using rather than the crtc
it is currently using. That doesn't work all that well because
we may have to do vblank waits etc. and the other pipe might
not even be enabled here. So let's pass the plane's current crtc to
intel_plane_disable_noatomic() so that it can its job correctly.
To do that semi-cleanly we also have to change the plane readout
to record the plane's visibility into the bitmasks of the crtc
where the plane is currently enabled rather than to the crtc
we want to use for the plane.
One caveat here is that our active_planes bitmask will get confused
if both planes are enabled on the same pipe. Fortunately we can use
plane_mask to reconstruct active_planes sufficiently since
plane_mask still has the same meaning (is the plane visible?)
during readout. We also have to do the same during the initial
plane readout as the second plane could clear the active_planes
bit the first plane had already set.
v2: Rely on fixup_active_planes() to populate active_planes fully (Daniel)
Add Daniel's proposed comment to better document why we do this
Drop the redundant intel_set_plane_visible() call
Cc: stable@vger.kernel.org # fcba862e8428 drm/i915: Have plane->get_hw_state() return the current pipe
Cc: stable@vger.kernel.org
Cc: Dennis <dennis.nezic@utoronto.ca>
Cc: Daniel Vetter <daniel@ffwll.ch>
Tested-by: Dennis <dennis.nezic@utoronto.ca>
Tested-by: Peter Nowee <peter.nowee@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105637
Fixes: b1e01595a6 ("drm/i915: Redo plane sanitation during readout")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003145017.4527-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print out the information whether the port and sink can each
do MST. And let's include the modparam in the debug output as well.
Makes life a little less confusing when you don't have to wonder
why MST isn't kicking in.
This does cause a slight change in our behaviour towards the sink.
Previously we only read the MSTM_CAP register after passing all
the other checks. Now we will read that register regardless. Hopefully
some crazy sink doesn't get confused by a simple register read.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003184210.1306-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
If the HW has not processed the db invalidation request yet, clearing
the cookie can generate a db ring. We clear the cookie when we
(re-)allocate the doorbell so no need to do it on destroy as well as no
one is going to look at it while the doorbell is inactive
v2: fix typo in patch title (Michal)
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181002215430.15049-2-daniele.ceraolospurio@intel.com
GuC stores some data in there, which might be stale after a reset.
We already reset the WQ head and tail, but more things are being moved
to the descriptor with the interface updates. Instead of trying to track
them one by one, always memset and init the descriptors from scratch
after GuC is loaded.
The code is also reorganized so that the above operations and the
doorbell creation are grouped as "client enabling"
v2: add proc_desc_fini for symmetry (Daniele), remove unneeded var init,
add guc_is_alive() (Michal)
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181002215430.15049-1-daniele.ceraolospurio@intel.com
Inside the execlists submission tasklet, we often make the mistake of
assuming that everything beneath the request is available for use.
However, the submission and the request live on two separate timelines,
and the request contents may be freed from an early retirement before we
have had a chance to run the submission tasklet (think ksoftirqd). To
safeguard ourselves against any mistakes, flush the tasklet before we
unpin the context if execlists still has a reference to this context.
v2: Pull hw_context->active tracking into schedule_in and schedule_out.
References: 60367132a2 ("drm/i915: Avoid use-after-free of ctx in request tracepoints")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003110941.27886-1-chris@chris-wilson.co.uk
We do not need to continually clear our dedicated PTE for error capture
as it will be updated and invalidated to the next object. Only at the
end do we wish to be sure that the PTE doesn't point back to any buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001194447.29910-3-chris@chris-wilson.co.uk
The final call to zlib_deflate(Z_FINISH) may require more output
space to be allocated and so needs to re-invoked. Failure to do so in
the current code leads to incomplete zlib streams (albeit intact due to
the use of Z_SYNC_FLUSH) resulting in the occasional short object
capture.
v2: Check against overrunning our pre-allocated page array
v3: Drop Z_SYNC_FLUSH entirely
Testcase: igt/i915-error-capture.js
Fixes: 0a97015d45 ("drm/i915: Compress GPU objects in error state")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.10+
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003082422.23214-1-chris@chris-wilson.co.uk
