Under certain conditions, Cadence's I2C controller's transfer_size
register will roll over and generate invalid read transactions. Before
this change, the ISR relied solely on the RXDV bit to determine when to
write more data to the user's buffer. The invalid read data would cause
overruns, smashing stacks and worse.
This change stops the buffer writes to the requested boundary and
reports the error. The controller will be reset so normal transactions
may resume.
Signed-off-by: Alex Williams <alex.williams@ni.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> # in a seperate mail
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for Intel Comet Lake PCH-V which is based on Intel Kaby
Lake. Difference between it and other Comet Lake variants is that former
uses previous iTCO version 4 and latter use version 6 like Intel Cannon
Lake PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a statement that is indented one level too deeply, remove
the extraneous tab.
Fixes: b4c119dbc3 ("i2c: xiic: Add timeout to the rx fifo wait loop")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a spelling mistake in a module parameter description.
Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the help text to reflect current support devices:
1. The Exynos high speed I2C driver supports Exynos5 (ARMv7), Exynos5433
and Exynos7 (both ARMv8) SoCs,
2. The S3C I2C driver supports S3C, S5Pv210 and Exynos{3,4,5} SoCs.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some of the I2C bus drivers can be compile tested to increase build
coverage. This requires also:
1. Adding dependencies on COMMON_CLK for BCM2835 and Meson I2C
controllers,
2. Adding 'if' conditional to 'default y' so they will not get enabled
by default on all other architectures,
3. Limiting few compile test options to supported architectures (which
provide the readsX()/writesX() primitives).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[wsa: revert chunk for ZX2967. it needs more preparation]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The recommendation is that the set_active should be done
with pm runtime disabled.
Also fix the remove path for clocking.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It's not always the case that clock is already available when i2c
driver get probed at the first time, e.g. the clock is provided by
clock wizard which may be probed after i2c driver. So let's defer
the probe when devm_clk_get() call fails and give it chance to
try later.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add timeout to the rx fifo empty wait loop. Also check for the return
value for xiic_reinit and pass it to xiic_start_xfer.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
size_t should be printed with its own format to be 64-bit friendly and
fix warning when compiling on 64-bit platform (e.g. with COMPILE_TEST):
drivers/i2c/busses/i2c-highlander.c: In function ‘highlander_i2c_smbus_xfer’:
drivers/i2c/busses/i2c-highlander.c:325:22: warning:
format ‘%d’ expects argument of type ‘int’,
but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-pnx.c: In function ‘i2c_pnx_probe’:
drivers/i2c/busses/i2c-pnx.c:737:47: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 5 has type ‘resource_size_t {aka long long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-pmcmsp.c: In function ‘pmcmsptwi_probe’:
drivers/i2c/busses/i2c-pmcmsp.c:276:25: warning:
format ‘%x’ expects argument of type ‘unsigned int’,
but argument 3 has type ‘resource_size_t {aka long long unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
iomem pointers should be printed with pointer format to hide the
actual value and fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
drivers/i2c/busses/i2c-stu300.c: In function ‘stu300_wait_while_busy’:
drivers/i2c/busses/i2c-stu300.c:446:76: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is more robust to check completion status in addition to the left time
in a case of DMA transfer because transfer's completion happens in two
phases [one is ISR, other is tasklet] and thus it is possible that DMA is
completed while I2C completion awaiting times out because of the deferred
notification done by the DMA driver. The DMA completion status becomes
100% actual after DMA synchronization. This fixes spurious DMA timeouts
when system is under load.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is possible that I2C could error out in the middle of DMA transfer and
in this case DMA channel needs to be reset, otherwise a follow up transfer
will fail because DMA channel stays blocked.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is nothing to synchronize in regards to memory accesses for PIO
transfers and for DMA transfers the DMA API takes care of the syncing.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA is preferred for a larger transfers, while PIO is preferred for a
smaller transfers to avoid unnecessary DMA overhead. There is no strict
size limitations for the PIO-mode transfers, so let's rename the constant
for clarity.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
System shutdown may happen with interrupts being disabled and in this case
kernel may hang if atomic transfer isn't supported by driver.
There were several occurrences where I found my Nexus 7 completely
discharged despite of being turned off and then one day I spotted this in
the log:
reboot: Power down
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/i2c/i2c-core.h:40 i2c_transfer+0x95/0x9c
No atomic I2C transfer handler for 'i2c-1'
Modules linked in: tegra30_devfreq
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.4.0-next-20191202-00120-gf7ecd80fb803-dirty #3195
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[<c010e4b5>] (unwind_backtrace) from [<c010a0fd>] (show_stack+0x11/0x14)
[<c010a0fd>] (show_stack) from [<c09995e5>] (dump_stack+0x85/0x94)
[<c09995e5>] (dump_stack) from [<c011f3d1>] (__warn+0xc1/0xc4)
[<c011f3d1>] (__warn) from [<c011f691>] (warn_slowpath_fmt+0x61/0x78)
[<c011f691>] (warn_slowpath_fmt) from [<c069a8dd>] (i2c_transfer+0x95/0x9c)
[<c069a8dd>] (i2c_transfer) from [<c05667f1>] (regmap_i2c_read+0x4d/0x6c)
[<c05667f1>] (regmap_i2c_read) from [<c0563601>] (_regmap_raw_read+0x99/0x1cc)
[<c0563601>] (_regmap_raw_read) from [<c0563757>] (_regmap_bus_read+0x23/0x38)
[<c0563757>] (_regmap_bus_read) from [<c056293d>] (_regmap_read+0x3d/0xfc)
[<c056293d>] (_regmap_read) from [<c0562d3b>] (_regmap_update_bits+0x87/0xc4)
[<c0562d3b>] (_regmap_update_bits) from [<c0563add>] (regmap_update_bits_base+0x39/0x50)
[<c0563add>] (regmap_update_bits_base) from [<c056fd39>] (max77620_pm_power_off+0x29/0x2c)
[<c056fd39>] (max77620_pm_power_off) from [<c013bbdd>] (__do_sys_reboot+0xe9/0x170)
[<c013bbdd>] (__do_sys_reboot) from [<c0101001>] (ret_fast_syscall+0x1/0x28)
Exception stack(0xde907fa8 to 0xde907ff0)
7fa0: 00000000 00000000 fee1dead 28121969 4321fedc 00000000
7fc0: 00000000 00000000 00000000 00000058 00000000 00000000 00000000 00000000
7fe0: 0045adf0 bed9abb8 004444a0 b6c666d0
---[ end trace bdd18f87595b1a5e ]---
The atomic transferring is implemented by enforcing PIO mode for the
transfer and by polling interrupt status until transfer is completed or
failed.
Now system shuts down properly every time.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Potentially it is possible that interrupt may fire after transfer timeout.
That may not end up well for the next transfer because interrupt handling
may race with hardware resetting.
This is very unlikely to happen in practice, but anyway let's prevent the
potential problem by enabling interrupt only at the moments when it is
actually necessary to get some interrupt event.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After removal of the parport-light driver, this include is used by the
parport driver exclusively and can be included in the main source. Move
module parameter declarations to its variable declaration while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver is not 'new' anymore, so remove details from the driver it
surpassed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The justification of a light version of the parport driver was less
overhead for embedded systems. Well, today, even if an embedded system
still has a parport, it surely can handle the fully-fledged parport
driver. Remove it to reduce the maintenance burden.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
One of the recent Tegra I2C commits made a change that resumes runtime PM
during driver's probe, but it missed to put the RPM in a case of error.
Note that it's not correct to use pm_runtime_status_suspended because it
breaks RPM refcounting.
Fixes: 8ebf15e9c8 ("i2c: tegra: Move suspend handling to NOIRQ phase")
Cc: <stable@vger.kernel.org> # v5.4+
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I noticed that sometime I2C clock is kept enabled during suspend-resume.
This happens because runtime PM defers dynamic suspension and thus it may
happen that runtime PM is in active state when system enters into suspend.
In particular I2C controller that is used for CPU's DVFS is often kept ON
during suspend because CPU's voltage scaling happens quite often.
Fixes: 8ebf15e9c8 ("i2c: tegra: Move suspend handling to NOIRQ phase")
Cc: <stable@vger.kernel.org> # v5.4+
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Boards with some of the 32-bit SoCs (mostly Meson8 and Meson8m2) use a
Ricoh RN5T618 PMU which acts as system power controller. The driver for
the system power controller may need to the I2C bus just before shutting
down or rebooting the system. At this stage the interrupts may be
disabled already.
Implement the master_xfer_atomic callback so the driver for the RN5T618
PMU can communicate properly with the PMU when shutting down or
rebooting the board. The CTRL register has a status bit which can be
polled to determine when processing has completed. According to the
public S805 datasheet the value 0 means "idle" and 1 means "running".
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[wsa: converted some whitespace alignment]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit bebff81fb8 ("i2c: bcm2835: Model Divider in CCF") introduced
a NULL pointer dereference on driver unload. It seems that we can't fetch
the bus clock via devm_clk_get in bcm2835_i2c_remove. As an alternative
approach store a pointer to the bus clock in the private driver structure.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for probing i2c driver on the X1000 Soc from Ingenic.
call the corresponding fifo parameter according to the device
model obtained from the devicetree.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch changes the I2C fault codes according to the specified
values in Documentation/i2c/fault-codes.
Signed-off-by: Christoph Müllner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Platform data structs are initialized by default with zero values.
Thus it becomes redundant to initialize them manually to zero (false).
Remove extra false initialization for field members in structs.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In SAM9X60 datasheet, FLEX_TWI_CWGR register description mentions clock
offset of 3 cycles (compared to 4 in eg. SAMA5D3).
This is the same offset as in SAMA5D2.
Fixes: b002779237 ("i2c: at91: add new platform support for sam9x60")
Suggested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has mostly driver updates this time.
The few noteworthy changes are: the core has now support for analog
and digital filters with at91 being the first user, a core addition to
replace the NULL returning i2c_new_probed_device() with an ERR_PTR
variant, and the pxa driver has finally being moved to use the generic
I2C slave interface. We have quite a significant number of reviews per
patch this time, so thank you to all involved!"
* 'i2c/for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
video: fbdev: matrox: convert to i2c_new_scanned_device
i2c: icy: convert to i2c_new_scanned_device
i2c: replace i2c_new_probed_device with an ERR_PTR variant
i2c: Fix Kconfig indentation
i2c: smbus: Don't filter out duplicate alerts
i2c: i801: Correct Intel Jasper Lake SOC naming
i2c: i2c-stm32f7: fix 10-bits check in slave free id search loop
i2c: iproc: Add i2c repeated start capability
i2c: remove helpers for ref-counting clients
i2c: tegra: Use dma_request_chan() directly for channel request
i2c: sh_mobile: Use dma_request_chan() directly for channel request
i2c: qup: Use dma_request_chan() directly for channel request
i2c: at91: Use dma_request_chan() directly for channel request
i2c: rcar: Remove superfluous call to clk_get_rate()
i2c: pxa: remove unused i2c-slave APIs
i2c: pxa: migrate to new i2c_slave APIs
i2c: cros-ec-tunnel: Make the device acpi compatible
i2c: stm32f7: report dma error during probe
i2c: icy: no need to populate address for scanned device
i2c: xiic: Fix kerneldoc warnings
...
Move from the deprecated i2c_new_probed_device() to the new
i2c_new_scanned_device(). Make use of the new ERRPTR if suitable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Max Staudt <max@enpas.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no suffix applied to Intel Jasper Lake SOC. Remove it
from the comments and definitions. Besides that, it's a SOC,
thus replace PCH with SOC where it appropriate.
Fixes: e0c61c0479 ("i2c: i801: Add support for Intel Jasper Lake")
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix a typo in the free slave id search loop. Instead of I2C_CLIENT_PEC,
it should have been I2C_CLIENT_TEN. The slave id 1 can only handle 7-bit
addresses and thus is not eligible in case of 10-bit addresses.
As a matter of fact none of the slave id support I2C_CLIENT_PEC, overall
check is performed at the beginning of the stm32f7_i2c_reg_slave function.
Fixes: 60d609f30d ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable handling of i2c repeated start. The current code
handles a multi msg i2c transfer as separate i2c bus
transactions. This change will now handle this case
using the i2c repeated start protocol. The number of msgs
in a transfer is limited to two, and must be a write
followed by a read.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Icarus Chau <icarus.chau@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Shivaraj Shetty <sshetty1@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Variable "rate" already contains the current clock rate, so use that
rather than calling clk_get_rate() again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With the i2c-pxa driver migrated to the standard i2c-slave
APIs, the custom APIs and structures are no longer needed
or used. Remove them.
Signed-off-by: Patrick Williams <alpawi@amazon.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
