Since commit 1afb648e94 ("btrfs: use standard debug config option to
enable free-space-cache debug prints"), we started to log error messages
that were never logged before since there was no DEBUG macro defined
anywhere. This started to make test case btrfs/187 to fail very often,
as it greps for any btrfs error messages in dmesg/syslog and fails if
any is found:
(...)
btrfs/186 1s ... 2s
btrfs/187 - output mismatch (see .../results//btrfs/187.out.bad)
\--- tests/btrfs/187.out 2019-05-17 12:48:32.537340749 +0100
\+++ /home/fdmanana/git/hub/xfstests/results//btrfs/187.out.bad ...
\@@ -1,3 +1,8 @@
QA output created by 187
Create a readonly snapshot of 'SCRATCH_MNT' in 'SCRATCH_MNT/snap1'
Create a readonly snapshot of 'SCRATCH_MNT' in 'SCRATCH_MNT/snap2'
+[268364.139958] BTRFS error (device sdc): failed to write free space cache for block group 30408704
+[268380.156503] BTRFS error (device sdc): failed to write free space cache for block group 30408704
+[268380.161703] BTRFS error (device sdc): failed to write free space cache for block group 30408704
+[268380.253180] BTRFS error (device sdc): failed to write free space cache for block group 30408704
...
(Run 'diff -u /home/fdmanana/git/hub/xfstests/tests/btrfs/187.out ...
btrfs/188 4s ... 2s
(...)
The space cache write failures happen due to ENOSPC when attempting to
update the free space cache items in the root tree. This happens because
when starting or joining a transaction we don't know how many block
groups we will end up changing (due to extent allocation or release) and
therefore never reserve space for updating free space cache items.
More often than not, the free space cache writeout succeeds since the
metadata space info is not yet full nor very close to being full, but
when it is, the space cache writeout fails with ENOSPC.
Occasional failures to write space caches are not considered critical
since they can be rebuilt when mounting the filesystem or the next
attempt to write a free space cache in the next transaction commit might
succeed, so we used to hide those error messages with a preprocessor
check for the existence of the DEBUG macro that was never enabled
anywhere.
A few other generic test cases also trigger the error messages due to
ENOSPC failure when writing free space caches as well, however they don't
fail since they don't grep dmesg/syslog for any btrfs specific error
messages.
So change the messages from 'error' level to 'debug' level, as it doesn't
make much sense to have error messages triggered only if the debug macro
is enabled plus, more importantly, the error is not serious nor highly
unexpected.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently the error messages logged when we fail to write a free space
cache or an inode cache are not very useful as they don't mention what
was the error. So include the error number in the messages.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The label 'fail_unlock' is pointless, all it does is to jump to the label
'out', so just remove it.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We are currently treating any non-zero return value from btrfs_next_leaf()
the same way, by going to the code that inserts a new checksum item in the
tree. However if btrfs_next_leaf() returns an error (a value < 0), we
should just stop and return the error, and not behave as if nothing has
happened, since in that case we do not have a way to know if there is a
next leaf or we are currently at the last leaf already.
So fix that by returning the error from btrfs_next_leaf().
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we want to add checksums into the checksums tree, or a log tree, we
try whenever possible to extend existing checksum items, as this helps
reduce amount of metadata space used, since adding a new item uses extra
metadata space for a btrfs_item structure (25 bytes).
However we have two inefficiencies in the current approach:
1) After finding a checksum item that covers a range with an end offset
that matches the start offset of the checksum range we want to insert,
we release the search path populated by btrfs_lookup_csum() and then
do another COW search on tree with the goal of getting additional
space for at least one checksum. Doing this path release and then
searching again is a waste of time because very often the leaf already
has enough free space for at least one more checksum;
2) After the COW search that guarantees we get free space in the leaf for
at least one more checksum, we end up not doing the extension of the
previous checksum item, and fallback to insertion of a new checksum
item, if the leaf doesn't have an amount of free space larger then the
space required for 2 checksums plus one btrfs_item structure - this is
pointless for two reasons:
a) We want to extend an existing item, so we don't need to account for
a btrfs_item structure (25 bytes);
b) We made the COW search with an insertion size for 1 single checksum,
so if the leaf ends up with a free space amount smaller then 2
checksums plus the size of a btrfs_item structure, we give up on the
extension of the existing item and jump to the 'insert' label, where
we end up releasing the path and then doing yet another search to
insert a new checksum item for a single checksum.
Fix these inefficiencies by doing the following:
- For case 1), before releasing the path just check if the leaf already
has enough space for at least 1 more checksum, and if it does, jump
directly to the item extension code, with releasing our current path,
which was already COWed by btrfs_lookup_csum();
- For case 2), fix the logic so that for item extension we require only
that the leaf has enough free space for 1 checksum, and not a minimum
of 2 checksums plus space for a btrfs_item structure.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When we have extents shared amongst different inodes in the same subvolume,
if we fsync them in parallel we can end up with checksum items in the log
tree that represent ranges which overlap.
For example, consider we have inodes A and B, both sharing an extent that
covers the logical range from X to X + 64KiB:
1) Task A starts an fsync on inode A;
2) Task B starts an fsync on inode B;
3) Task A calls btrfs_csum_file_blocks(), and the first search in the
log tree, through btrfs_lookup_csum(), returns -EFBIG because it
finds an existing checksum item that covers the range from X - 64KiB
to X;
4) Task A checks that the checksum item has not reached the maximum
possible size (MAX_CSUM_ITEMS) and then releases the search path
before it does another path search for insertion (through a direct
call to btrfs_search_slot());
5) As soon as task A releases the path and before it does the search
for insertion, task B calls btrfs_csum_file_blocks() and gets -EFBIG
too, because there is an existing checksum item that has an end
offset that matches the start offset (X) of the checksum range we want
to log;
6) Task B releases the path;
7) Task A does the path search for insertion (through btrfs_search_slot())
and then verifies that the checksum item that ends at offset X still
exists and extends its size to insert the checksums for the range from
X to X + 64KiB;
8) Task A releases the path and returns from btrfs_csum_file_blocks(),
having inserted the checksums into an existing checksum item that got
its size extended. At this point we have one checksum item in the log
tree that covers the logical range from X - 64KiB to X + 64KiB;
9) Task B now does a search for insertion using btrfs_search_slot() too,
but it finds that the previous checksum item no longer ends at the
offset X, it now ends at an of offset X + 64KiB, so it leaves that item
untouched.
Then it releases the path and calls btrfs_insert_empty_item()
that inserts a checksum item with a key offset corresponding to X and
a size for inserting a single checksum (4 bytes in case of crc32c).
Subsequent iterations end up extending this new checksum item so that
it contains the checksums for the range from X to X + 64KiB.
So after task B returns from btrfs_csum_file_blocks() we end up with
two checksum items in the log tree that have overlapping ranges, one
for the range from X - 64KiB to X + 64KiB, and another for the range
from X to X + 64KiB.
Having checksum items that represent ranges which overlap, regardless of
being in the log tree or in the chekcsums tree, can lead to problems where
checksums for a file range end up not being found. This type of problem
has happened a few times in the past and the following commits fixed them
and explain in detail why having checksum items with overlapping ranges is
problematic:
27b9a8122f "Btrfs: fix csum tree corruption, duplicate and outdated checksums"
b84b8390d6 "Btrfs: fix file read corruption after extent cloning and fsync"
40e046acbd "Btrfs: fix missing data checksums after replaying a log tree"
Since this specific instance of the problem can only happen when logging
inodes, because it is the only case where concurrent attempts to insert
checksums for the same range can happen, fix the issue by using an extent
io tree as a range lock to serialize checksum insertion during inode
logging.
This issue could often be reproduced by the test case generic/457 from
fstests. When it happens it produces the following trace:
BTRFS critical (device dm-0): corrupt leaf: root=18446744073709551610 block=30625792 slot=42, csum end range (15020032) goes beyond the start range (15015936) of the next csum item
BTRFS info (device dm-0): leaf 30625792 gen 7 total ptrs 49 free space 2402 owner 18446744073709551610
BTRFS info (device dm-0): refs 1 lock (w:0 r:0 bw:0 br:0 sw:0 sr:0) lock_owner 0 current 15884
item 0 key (18446744073709551606 128 13979648) itemoff 3991 itemsize 4
item 1 key (18446744073709551606 128 13983744) itemoff 3987 itemsize 4
item 2 key (18446744073709551606 128 13987840) itemoff 3983 itemsize 4
item 3 key (18446744073709551606 128 13991936) itemoff 3979 itemsize 4
item 4 key (18446744073709551606 128 13996032) itemoff 3975 itemsize 4
item 5 key (18446744073709551606 128 14000128) itemoff 3971 itemsize 4
(...)
BTRFS error (device dm-0): block=30625792 write time tree block corruption detected
------------[ cut here ]------------
WARNING: CPU: 1 PID: 15884 at fs/btrfs/disk-io.c:539 btree_csum_one_bio+0x268/0x2d0 [btrfs]
Modules linked in: btrfs dm_thin_pool ...
CPU: 1 PID: 15884 Comm: fsx Tainted: G W 5.6.0-rc7-btrfs-next-58 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
RIP: 0010:btree_csum_one_bio+0x268/0x2d0 [btrfs]
Code: c7 c7 ...
RSP: 0018:ffffbb0109e6f8e0 EFLAGS: 00010296
RAX: 0000000000000000 RBX: ffffe1c0847b6080 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffffaa963988 RDI: 0000000000000001
RBP: ffff956a4f4d2000 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000526 R11: 0000000000000000 R12: ffff956a5cd28bb0
R13: 0000000000000000 R14: ffff956a649c9388 R15: 000000011ed82000
FS: 00007fb419959e80(0000) GS:ffff956a7aa00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000fe6d54 CR3: 0000000138696005 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
btree_submit_bio_hook+0x67/0xc0 [btrfs]
submit_one_bio+0x31/0x50 [btrfs]
btree_write_cache_pages+0x2db/0x4b0 [btrfs]
? __filemap_fdatawrite_range+0xb1/0x110
do_writepages+0x23/0x80
__filemap_fdatawrite_range+0xd2/0x110
btrfs_write_marked_extents+0x15e/0x180 [btrfs]
btrfs_sync_log+0x206/0x10a0 [btrfs]
? kmem_cache_free+0x315/0x3b0
? btrfs_log_inode+0x1e8/0xf90 [btrfs]
? __mutex_unlock_slowpath+0x45/0x2a0
? lockref_put_or_lock+0x9/0x30
? dput+0x2d/0x580
? dput+0xb5/0x580
? btrfs_sync_file+0x464/0x4d0 [btrfs]
btrfs_sync_file+0x464/0x4d0 [btrfs]
do_fsync+0x38/0x60
__x64_sys_fsync+0x10/0x20
do_syscall_64+0x5c/0x280
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fb41953a6d0
Code: 48 3d ...
RSP: 002b:00007ffcc86bd218 EFLAGS: 00000246 ORIG_RAX: 000000000000004a
RAX: ffffffffffffffda RBX: 000000000000000d RCX: 00007fb41953a6d0
RDX: 0000000000000009 RSI: 0000000000040000 RDI: 0000000000000003
RBP: 0000000000040000 R08: 0000000000000001 R09: 0000000000000009
R10: 0000000000000064 R11: 0000000000000246 R12: 0000556cf4b2c060
R13: 0000000000000100 R14: 0000000000000000 R15: 0000556cf322b420
irq event stamp: 0
hardirqs last enabled at (0): [<0000000000000000>] 0x0
hardirqs last disabled at (0): [<ffffffffa96bdedf>] copy_process+0x74f/0x2020
softirqs last enabled at (0): [<ffffffffa96bdedf>] copy_process+0x74f/0x2020
softirqs last disabled at (0): [<0000000000000000>] 0x0
---[ end trace d543fc76f5ad7fd8 ]---
In that trace the tree checker detected the overlapping checksum items at
the time when we triggered writeback for the log tree when syncing the
log.
Another trace that can happen is due to BUG_ON() when deleting checksum
items while logging an inode:
BTRFS critical (device dm-0): slot 81 key (18446744073709551606 128 13635584) new key (18446744073709551606 128 13635584)
BTRFS info (device dm-0): leaf 30949376 gen 7 total ptrs 98 free space 8527 owner 18446744073709551610
BTRFS info (device dm-0): refs 4 lock (w:1 r:0 bw:0 br:0 sw:1 sr:0) lock_owner 13473 current 13473
item 0 key (257 1 0) itemoff 16123 itemsize 160
inode generation 7 size 262144 mode 100600
item 1 key (257 12 256) itemoff 16103 itemsize 20
item 2 key (257 108 0) itemoff 16050 itemsize 53
extent data disk bytenr 13631488 nr 4096
extent data offset 0 nr 131072 ram 131072
(...)
------------[ cut here ]------------
kernel BUG at fs/btrfs/ctree.c:3153!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC PTI
CPU: 1 PID: 13473 Comm: fsx Not tainted 5.6.0-rc7-btrfs-next-58 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
RIP: 0010:btrfs_set_item_key_safe+0x1ea/0x270 [btrfs]
Code: 0f b6 ...
RSP: 0018:ffff95e3889179d0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000051 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffffb7763988 RDI: 0000000000000001
RBP: fffffffffffffff6 R08: 0000000000000000 R09: 0000000000000001
R10: 00000000000009ef R11: 0000000000000000 R12: ffff8912a8ba5a08
R13: ffff95e388917a06 R14: ffff89138dcf68c8 R15: ffff95e388917ace
FS: 00007fe587084e80(0000) GS:ffff8913baa00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe587091000 CR3: 0000000126dac005 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
btrfs_del_csums+0x2f4/0x540 [btrfs]
copy_items+0x4b5/0x560 [btrfs]
btrfs_log_inode+0x910/0xf90 [btrfs]
btrfs_log_inode_parent+0x2a0/0xe40 [btrfs]
? dget_parent+0x5/0x370
btrfs_log_dentry_safe+0x4a/0x70 [btrfs]
btrfs_sync_file+0x42b/0x4d0 [btrfs]
__x64_sys_msync+0x199/0x200
do_syscall_64+0x5c/0x280
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fe586c65760
Code: 00 f7 ...
RSP: 002b:00007ffe250f98b8 EFLAGS: 00000246 ORIG_RAX: 000000000000001a
RAX: ffffffffffffffda RBX: 00000000000040e1 RCX: 00007fe586c65760
RDX: 0000000000000004 RSI: 0000000000006b51 RDI: 00007fe58708b000
RBP: 0000000000006a70 R08: 0000000000000003 R09: 00007fe58700cb61
R10: 0000000000000100 R11: 0000000000000246 R12: 00000000000000e1
R13: 00007fe58708b000 R14: 0000000000006b51 R15: 0000558de021a420
Modules linked in: dm_log_writes ...
---[ end trace c92a7f447a8515f5 ]---
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_compress_set_level() can be static function in the file
compression.c.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The inode lookup starting at btrfs_iget takes the full location key,
while only the objectid is used to match the inode, because the lookup
happens inside the given root thus the inode number is unique.
The entire location key is properly set up in btrfs_init_locked_inode.
Simplify the helpers and pass only inode number, renaming it to 'ino'
instead of 'objectid'. This allows to remove temporary variables key,
saving some stack space.
Signed-off-by: David Sterba <dsterba@suse.com>
The main function to lookup a root by its id btrfs_get_fs_root takes the
whole key, while only using the objectid. The value of offset is preset
to (u64)-1 but not actually used until btrfs_find_root that does the
actual search.
Switch btrfs_get_fs_root to use only objectid and remove all local
variables that existed just for the lookup. The actual key for search is
set up in btrfs_get_fs_root, reusing another key variable.
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
There are several reported runaway balance, that balance is flooding the
log with "found X extents" where the X never changes.
[CAUSE]
Commit d2311e6985 ("btrfs: relocation: Delay reloc tree deletion after
merge_reloc_roots") introduced BTRFS_ROOT_DEAD_RELOC_TREE bit to
indicate that one subvolume has finished its tree blocks swap with its
reloc tree.
However if balance is canceled or hits ENOSPC halfway, we didn't clear
the BTRFS_ROOT_DEAD_RELOC_TREE bit, leaving that bit hanging forever
until unmount.
Any subvolume root with that bit, would cause backref cache to skip this
tree block, as it has finished its tree block swap. This would cause
all tree blocks of that root be ignored by balance, leading to runaway
balance.
[FIX]
Fix the problem by also clearing the BTRFS_ROOT_DEAD_RELOC_TREE bit for
the original subvolume of orphan reloc root.
Add an umount check for the stale bit still set.
Fixes: d2311e6985 ("btrfs: relocation: Delay reloc tree deletion after merge_reloc_roots")
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When creating a snapshot, ordered extents need to be flushed and this
can take a long time.
In create_snapshot there are two locks held when this happens:
1. Destination directory inode lock
2. Global subvolume semaphore
This will unnecessarily block other operations like subvolume destroy,
create, or setflag until the snapshot is created.
We can fix that by moving the flush outside the locked section as this
does not depend on the aforementioned locks. The code factors out the
snapshot related work from create_snapshot to btrfs_mksnapshot.
__btrfs_ioctl_snap_create
btrfs_mksubvol
create_subvol
btrfs_mksnapshot
<flush>
btrfs_mksubvol
create_snapshot
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Robbie Ko <robbieko@synology.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
SHAREABLE flag is set for subvolumes because users can create snapshot
for subvolumes, thus sharing tree blocks of them.
But data reloc tree is not exposed to user space, as it's only an
internal tree for data relocation, thus it doesn't need the full path
replacement handling at all.
This patch will make data reloc tree a non-shareable tree, and add
btrfs_fs_info::data_reloc_root for data reloc tree, so relocation code
can grab it from fs_info directly.
This would slightly improve tree relocation, as now data reloc tree
can go through regular COW routine to get relocated, without bothering
the complex tree reloc tree routine.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are a lot of root owner checks in btrfs_truncate_inode_items()
like:
if (test_bit(BTRFS_ROOT_SHAREABLE, &root->state) ||
root == fs_info->tree_root)
But considering that, only these trees can have INODE_ITEMs:
- tree root (for v1 space cache)
- subvolume trees
- tree reloc trees
- data reloc tree
- log trees
And since subvolume/tree reloc/data reloc trees all have SHAREABLE bit,
and we're checking tree root manually, so above check is just excluding
log trees.
This patch will replace two of such checks to a simpler one:
if (root->root_key.objectid != BTRFS_TREE_LOG_OBJECTID)
This would merge btrfs_drop_extent_cache() and lock_extent_bits() call
into the same if branch.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The name BTRFS_ROOT_REF_COWS is not very clear about the meaning.
In fact, that bit can only be set to those trees:
- Subvolume roots
- Data reloc root
- Reloc roots for above roots
All other trees won't get this bit set. So just by the result, it is
obvious that, roots with this bit set can have tree blocks shared with
other trees. Either shared by snapshots, or by reloc roots (an special
snapshot created by relocation).
This patch will rename BTRFS_ROOT_REF_COWS to BTRFS_ROOT_SHAREABLE to
make it easier to understand, and update all comment mentioning
"reference counted" to follow the rename.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit dccdb07bc9 ("btrfs: kill btrfs_fs_info::volume_mutex") removed
the last use of the volume_mutex, forgetting to update the comment.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The fallback path calls helper write_extent_buffer to do write of the
data spanning two extent buffer pages. As the size is known, we can do
the write directly in two steps. This removes one function call and
compiler can optimize memcpy as the sizes are known at compile time. The
cached token address is set to the second page.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The helper write_extent_buffer is called to do write of the data
spanning two extent buffer pages. As the size is known, we can do the
write directly in two steps. This removes one function call and
compiler can optimize memcpy as the sizes are known at compile time.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The fallback path calls helper read_extent_buffer to do read of the data
spanning two extent buffer pages. As the size is known, we can do the
read directly in two steps. This removes one function call and compiler
can optimize memcpy as the sizes are known at compile time. The cached
token address is set to the second page.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The helper read_extent_buffer is called to do read of the data spanning
two extent buffer pages. As the size is known, we can do the read
directly in two steps. This removes one function call and compiler can
optimize memcpy as the sizes are known at compile time.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Helpers that iterate over extent buffer pages set up several variables,
one of them is finding out offset of the extent buffer start within a
page. Right now we have extent buffers aligned to page sizes so this is
effectively storing zero. This makes the code harder the follow and can
be simplified.
The same change is done in all the helpers:
* remove: size_t start_offset = offset_in_page(eb->start);
* simplify code using start_offset
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are many helpers around extent buffers, found in extent_io.h and
ctree.h. Most of them can be converted to take constified eb as there
are no changes to the extent buffer structure itself but rather the
pages.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All uses of map_private_extent_buffer have been replaced by more
effective way. The set/get helpers have their own bounds checker.
The function name was confusing since the non-private helper was removed
in a65917156e ("Btrfs: stop using highmem for extent_buffers") many
years ago.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The bin search jumps over the extent buffer item keys, comparing
directly the bytes if the key is in one page, or storing it in a
temporary buffer in case it spans two pages.
The mapping start and length are obtained from map_private_extent_buffer,
which is heavy weight compared to what we need. We know the key size and
can find out the eb page in a simple way. For keys spanning two pages
the fallback read_extent_buffer is used.
The temporary variables are reduced and moved to the scope of use.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The set/get token helpers either use the cached address in the token or
unconditionally call map_private_extent_buffer to get the address of
page containing the requested offset plus the mapping start and length.
Depending on the return value, the fast path uses unaligned put to write
data within a page, or fall back to write_extent_buffer that can handle
writes spanning more pages.
This is all wasteful. We know the number of bytes to write, 1/2/4/8 and
can find out the page. Then simply check if it's contained or the
fallback is needed. The token address is updated to the page, or the on
the next index, expecting that the next write will use that.
This saves one function call to map_private_extent_buffer and several
unnecessary temporary variables.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The helpers unconditionally call map_private_extent_buffer to get the
address of page containing the requested offset plus the mapping start
and length. Depending on the return value, the fast path uses unaligned
put to write data within a page, or fall back to write_extent_buffer
that can handle writes spanning more pages.
This is all wasteful. We know the number of bytes to write, 1/2/4/8 and
can find out the page. Then simply check if it's contained or the
fallback is needed.
This saves one function call to map_private_extent_buffer and several
unnecessary temporary variables.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The set/get token helpers either use the cached address in the token or
unconditionally call map_private_extent_buffer to get the address of
page containing the requested offset plus the mapping start and length.
Depending on the return value, the fast path uses unaligned read to get
data within a page, or fall back to read_extent_buffer that can handle
reads spanning more pages.
This is all wasteful. We know the number of bytes to read, 1/2/4/8 and
can find out the page. Then simply check if it's contained or the
fallback is needed. The token address is updated to the page, or the on
the next index, expecting that the next read will use that.
This saves one function call to map_private_extent_buffer and several
unnecessary temporary variables.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The helpers unconditionally call map_private_extent_buffer to get the
address of page containing the requested offset plus the mapping start
and length. Depending on the return value, the fast path uses unaligned
read to get data within a page, or fall back to read_extent_buffer that
can handle reads spanning more pages.
This is all wasteful. We know the number of bytes to read, 1/2/4/8 and
can find out the page. Then simply check if it's contained or the
fallback is needed.
This saves one function call to map_private_extent_buffer and several
unnecessary temporary variables.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The bounds checking is now done in map_private_extent_buffer but that
will be removed in following patches and some sanity checks should still
be done.
There are two separate checks to see the kind of out of bounds access:
partial (start offset is in the buffer) or complete (both start and end
are out).
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All the set/get helpers first check if the token contains a cached
address. After first use the address is always valid, but the extra
check is done for each call.
The token initialization can optimistically set it to the first extent
buffer page, that we know always exists. Then the condition in all
btrfs_token_*/btrfs_set_token_* can be simplified by removing the
address check from the condition, but for development the assertion
still makes sure it's valid.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The token is supposed to cache the last page used by the set/get
helpers. In leaf_space_used the first and last items are accessed, it's
not likely they'd be on the same page so there's some overhead caused
updating the token address but not using it.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The set/get token is supposed to cache the last page that was accessed
so it speeds up subsequential access to the eb. It does not make sense
to use that for just one change, which is the case of inode size in
overwrite_item.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that all set/get helpers use the eb from the token, we don't need to
pass it to many btrfs_token_*/btrfs_set_token_* helpers, saving some
stack space.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The token stores a copy of the extent buffer pointer but does not make
any use of it besides sanity checks. We can use it and drop the eb
parameter from several functions, this patch only switches the use
inside the set/get helpers.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
disk-io.h is included more than once in block-group.c, remove it.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: David Sterba <dsterba@suse.com>
The name of this function contains the word "cache", which is left from
the times where btrfs_block_group was called btrfs_block_group_cache.
Now this "cache" doesn't match anything, and we have better namings for
functions like read/insert/remove_block_group_item().
Rename it to update_block_group_item().
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently the block group item insert is pretty straight forward, fill
the block group item structure and insert it into extent tree.
However the incoming skinny block group feature is going to change this,
so this patch will refactor insertion into a new function,
insert_block_group_item(), to make the incoming feature easier to add.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When deleting a block group item, it's pretty straight forward, just
delete the item pointed by the key. However it will not be that
straight-forward for incoming skinny block group item.
So refactor the block group item deletion into a new function,
remove_block_group_item(), also to make the already lengthy
btrfs_remove_block_group() a little shorter.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Structure btrfs_block_group has the following members which are
currently read from on-disk block group item and key:
- length - from item key
- used
- flags - from block group item
However for incoming skinny block group tree, we are going to read those
members from different sources.
This patch will refactor such read by:
- Don't initialize btrfs_block_group::length at allocation
Caller should initialize them manually.
Also to avoid possible (well, only two callers) missing
initialization, add extra ASSERT() in btrfs_add_block_group_cache().
- Refactor length/used/flags initialization into one function
The new function, fill_one_block_group() will handle the
initialization of such members.
- Use btrfs_block_group::length to replace key::offset
Since skinny block group item would have a different meaning for its
key offset.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Regular block group items in extent tree are scattered inside the huge
tree, thus forward readahead makes no sense.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Whenever a chown is executed, all capabilities of the file being touched
are lost. When doing incremental send with a file with capabilities,
there is a situation where the capability can be lost on the receiving
side. The sequence of actions bellow shows the problem:
$ mount /dev/sda fs1
$ mount /dev/sdb fs2
$ touch fs1/foo.bar
$ setcap cap_sys_nice+ep fs1/foo.bar
$ btrfs subvolume snapshot -r fs1 fs1/snap_init
$ btrfs send fs1/snap_init | btrfs receive fs2
$ chgrp adm fs1/foo.bar
$ setcap cap_sys_nice+ep fs1/foo.bar
$ btrfs subvolume snapshot -r fs1 fs1/snap_complete
$ btrfs subvolume snapshot -r fs1 fs1/snap_incremental
$ btrfs send fs1/snap_complete | btrfs receive fs2
$ btrfs send -p fs1/snap_init fs1/snap_incremental | btrfs receive fs2
At this point, only a chown was emitted by "btrfs send" since only the
group was changed. This makes the cap_sys_nice capability to be dropped
from fs2/snap_incremental/foo.bar
To fix that, only emit capabilities after chown is emitted. The current
code first checks for xattrs that are new/changed, emits them, and later
emit the chown. Now, __process_new_xattr skips capabilities, letting
only finish_inode_if_needed to emit them, if they exist, for the inode
being processed.
This behavior was being worked around in "btrfs receive" side by caching
the capability and only applying it after chown. Now, xattrs are only
emmited _after_ chown, making that workaround not needed anymore.
Link: https://github.com/kdave/btrfs-progs/issues/202
CC: stable@vger.kernel.org # 4.4+
Suggested-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When scrubbing a stripe, whenever we find an extent we lookup for its
checksums in the checksum tree. However we do it even for metadata extents
which don't have checksum items stored in the checksum tree, that is
only for data extents.
So make the lookup for checksums only if we are processing with a data
extent.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The helpers btrfs_freeze_block_group() and btrfs_unfreeze_block_group()
used to be named btrfs_get_block_group_trimming() and
btrfs_put_block_group_trimming() respectively.
At the time they were added to free-space-cache.c, by commit e33e17ee10
("btrfs: add missing discards when unpinning extents with -o discard")
because all the trimming related functions were in free-space-cache.c.
Now that the helpers were renamed and are used in scrub context as well,
move them to block-group.c, a much more logical location for them.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Back in 2014, commit 04216820fe ("Btrfs: fix race between fs trimming
and block group remove/allocation"), I added the 'trimming' member to the
block group structure. Its purpose was to prevent races between trimming
and block group deletion/allocation by pinning the block group in a way
that prevents its logical address and device extents from being reused
while trimming is in progress for a block group, so that if another task
deletes the block group and then another task allocates a new block group
that gets the same logical address and device extents while the trimming
task is still in progress.
After the previous fix for scrub (patch "btrfs: fix a race between scrub
and block group removal/allocation"), scrub now also has the same needs that
trimming has, so the member name 'trimming' no longer makes sense.
Since there is already a 'pinned' member in the block group that refers
to space reservations (pinned bytes), rename the member to 'frozen',
add a comment on top of it to describe its general purpose and rename
the helpers to increment and decrement the counter as well, to match
the new member name.
The next patch in the series will move the helpers into a more suitable
file (from free-space-cache.c to block-group.c).
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When scrub is verifying the extents of a block group for a device, it is
possible that the corresponding block group gets removed and its logical
address and device extents get used for a new block group allocation.
When this happens scrub incorrectly reports that errors were detected
and, if the the new block group has a different profile then the old one,
deleted block group, we can crash due to a null pointer dereference.
Possibly other unexpected and weird consequences can happen as well.
Consider the following sequence of actions that leads to the null pointer
dereference crash when scrub is running in parallel with balance:
1) Balance sets block group X to read-only mode and starts relocating it.
Block group X is a metadata block group, has a raid1 profile (two
device extents, each one in a different device) and a logical address
of 19424870400;
2) Scrub is running and finds device extent E, which belongs to block
group X. It enters scrub_stripe() to find all extents allocated to
block group X, the search is done using the extent tree;
3) Balance finishes relocating block group X and removes block group X;
4) Balance starts relocating another block group and when trying to
commit the current transaction as part of the preparation step
(prepare_to_relocate()), it blocks because scrub is running;
5) The scrub task finds the metadata extent at the logical address
19425001472 and marks the pages of the extent to be read by a bio
(struct scrub_bio). The extent item's flags, which have the bit
BTRFS_EXTENT_FLAG_TREE_BLOCK set, are added to each page (struct
scrub_page). It is these flags in the scrub pages that tells the
bio's end io function (scrub_bio_end_io_worker) which type of extent
it is dealing with. At this point we end up with 4 pages in a bio
which is ready for submission (the metadata extent has a size of
16Kb, so that gives 4 pages on x86);
6) At the next iteration of scrub_stripe(), scrub checks that there is a
pause request from the relocation task trying to commit a transaction,
therefore it submits the pending bio and pauses, waiting for the
transaction commit to complete before resuming;
7) The relocation task commits the transaction. The device extent E, that
was used by our block group X, is now available for allocation, since
the commit root for the device tree was swapped by the transaction
commit;
8) Another task doing a direct IO write allocates a new data block group Y
which ends using device extent E. This new block group Y also ends up
getting the same logical address that block group X had: 19424870400.
This happens because block group X was the block group with the highest
logical address and, when allocating Y, find_next_chunk() returns the
end offset of the current last block group to be used as the logical
address for the new block group, which is
18351128576 + 1073741824 = 19424870400
So our new block group Y has the same logical address and device extent
that block group X had. However Y is a data block group, while X was
a metadata one, and Y has a raid0 profile, while X had a raid1 profile;
9) After allocating block group Y, the direct IO submits a bio to write
to device extent E;
10) The read bio submitted by scrub reads the 4 pages (16Kb) from device
extent E, which now correspond to the data written by the task that
did a direct IO write. Then at the end io function associated with
the bio, scrub_bio_end_io_worker(), we call scrub_block_complete()
which calls scrub_checksum(). This later function checks the flags
of the first page, and sees that the bit BTRFS_EXTENT_FLAG_TREE_BLOCK
is set in the flags, so it assumes it has a metadata extent and
then calls scrub_checksum_tree_block(). That functions returns an
error, since interpreting data as a metadata extent causes the
checksum verification to fail.
So this makes scrub_checksum() call scrub_handle_errored_block(),
which determines 'failed_mirror_index' to be 1, since the device
extent E was allocated as the second mirror of block group X.
It allocates BTRFS_MAX_MIRRORS scrub_block structures as an array at
'sblocks_for_recheck', and all the memory is initialized to zeroes by
kcalloc().
After that it calls scrub_setup_recheck_block(), which is responsible
for filling each of those structures. However, when that function
calls btrfs_map_sblock() against the logical address of the metadata
extent, 19425001472, it gets a struct btrfs_bio ('bbio') that matches
the current block group Y. However block group Y has a raid0 profile
and not a raid1 profile like X had, so the following call returns 1:
scrub_nr_raid_mirrors(bbio)
And as a result scrub_setup_recheck_block() only initializes the
first (index 0) scrub_block structure in 'sblocks_for_recheck'.
Then scrub_recheck_block() is called by scrub_handle_errored_block()
with the second (index 1) scrub_block structure as the argument,
because 'failed_mirror_index' was previously set to 1.
This scrub_block was not initialized by scrub_setup_recheck_block(),
so it has zero pages, its 'page_count' member is 0 and its 'pagev'
page array has all members pointing to NULL.
Finally when scrub_recheck_block() calls scrub_recheck_block_checksum()
we have a NULL pointer dereference when accessing the flags of the first
page, as pavev[0] is NULL:
static void scrub_recheck_block_checksum(struct scrub_block *sblock)
{
(...)
if (sblock->pagev[0]->flags & BTRFS_EXTENT_FLAG_DATA)
scrub_checksum_data(sblock);
(...)
}
Producing a stack trace like the following:
[542998.008985] BUG: kernel NULL pointer dereference, address: 0000000000000028
[542998.010238] #PF: supervisor read access in kernel mode
[542998.010878] #PF: error_code(0x0000) - not-present page
[542998.011516] PGD 0 P4D 0
[542998.011929] Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC PTI
[542998.012786] CPU: 3 PID: 4846 Comm: kworker/u8:1 Tainted: G B W 5.6.0-rc7-btrfs-next-58 #1
[542998.014524] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[542998.016065] Workqueue: btrfs-scrub btrfs_work_helper [btrfs]
[542998.017255] RIP: 0010:scrub_recheck_block_checksum+0xf/0x20 [btrfs]
[542998.018474] Code: 4c 89 e6 ...
[542998.021419] RSP: 0018:ffffa7af0375fbd8 EFLAGS: 00010202
[542998.022120] RAX: 0000000000000000 RBX: ffff9792e674d120 RCX: 0000000000000000
[542998.023178] RDX: 0000000000000001 RSI: ffff9792e674d120 RDI: ffff9792e674d120
[542998.024465] RBP: 0000000000000000 R08: 0000000000000067 R09: 0000000000000001
[542998.025462] R10: ffffa7af0375fa50 R11: 0000000000000000 R12: ffff9791f61fe800
[542998.026357] R13: ffff9792e674d120 R14: 0000000000000001 R15: ffffffffc0e3dfc0
[542998.027237] FS: 0000000000000000(0000) GS:ffff9792fb200000(0000) knlGS:0000000000000000
[542998.028327] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[542998.029261] CR2: 0000000000000028 CR3: 00000000b3b18003 CR4: 00000000003606e0
[542998.030301] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[542998.031316] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[542998.032380] Call Trace:
[542998.032752] scrub_recheck_block+0x162/0x400 [btrfs]
[542998.033500] ? __alloc_pages_nodemask+0x31e/0x460
[542998.034228] scrub_handle_errored_block+0x6f8/0x1920 [btrfs]
[542998.035170] scrub_bio_end_io_worker+0x100/0x520 [btrfs]
[542998.035991] btrfs_work_helper+0xaa/0x720 [btrfs]
[542998.036735] process_one_work+0x26d/0x6a0
[542998.037275] worker_thread+0x4f/0x3e0
[542998.037740] ? process_one_work+0x6a0/0x6a0
[542998.038378] kthread+0x103/0x140
[542998.038789] ? kthread_create_worker_on_cpu+0x70/0x70
[542998.039419] ret_from_fork+0x3a/0x50
[542998.039875] Modules linked in: dm_snapshot dm_thin_pool ...
[542998.047288] CR2: 0000000000000028
[542998.047724] ---[ end trace bde186e176c7f96a ]---
This issue has been around for a long time, possibly since scrub exists.
The last time I ran into it was over 2 years ago. After recently fixing
fstests to pass the "--full-balance" command line option to btrfs-progs
when doing balance, several tests started to more heavily exercise balance
with fsstress, scrub and other operations in parallel, and therefore
started to hit this issue again (with btrfs/061 for example).
Fix this by having scrub increment the 'trimming' counter of the block
group, which pins the block group in such a way that it guarantees neither
its logical address nor device extents can be reused by future block group
allocations until we decrement the 'trimming' counter. Also make sure that
on each iteration of scrub_stripe() we stop scrubbing the block group if
it was removed already.
A later patch in the series will rename the block group's 'trimming'
counter and its helpers to a more generic name, since now it is not used
exclusively for pinning while trimming anymore.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The extent references v0 have been superseded long time go, there are
some unused declarations of access helpers. We can safely remove them
now. The struct btrfs_extent_ref_v0 is not used anywhere, but struct
btrfs_extent_item_v0 is still part of a backward compatibility check in
relocation.c and thus not removed.
Signed-off-by: David Sterba <dsterba@suse.com>
There's no callers in-tree anymore since
commit d24ee97b96 ("btrfs: use new helpers to set uuids in eb")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
For the following operation, qgroup is guaranteed to be screwed up due
to snapshot adding to a new qgroup:
# mkfs.btrfs -f $dev
# mount $dev $mnt
# btrfs qgroup en $mnt
# btrfs subv create $mnt/src
# xfs_io -f -c "pwrite 0 1m" $mnt/src/file
# sync
# btrfs qgroup create 1/0 $mnt/src
# btrfs subv snapshot -i 1/0 $mnt/src $mnt/snapshot
# btrfs qgroup show -prce $mnt/src
qgroupid rfer excl max_rfer max_excl parent child
-------- ---- ---- -------- -------- ------ -----
0/5 16.00KiB 16.00KiB none none --- ---
0/257 1.02MiB 16.00KiB none none --- ---
0/258 1.02MiB 16.00KiB none none 1/0 ---
1/0 0.00B 0.00B none none --- 0/258
^^^^^^^^^^^^^^^^^^^^
[CAUSE]
The problem is in btrfs_qgroup_inherit(), we don't have good enough
check to determine if the new relation would break the existing
accounting.
Unlike btrfs_add_qgroup_relation(), which has proper check to determine
if we can do quick update without a rescan, in btrfs_qgroup_inherit() we
can even assign a snapshot to multiple qgroups.
[FIX]
Fix it by manually marking qgroup inconsistent for snapshot inheritance.
For subvolume creation, since all its extents are exclusively owned, we
don't need to rescan.
In theory, we should call relation check like quick_update_accounting()
when doing qgroup inheritance and inform user about qgroup accounting
inconsistency.
But we don't have good mechanism to relay that back to the user in the
snapshot creation context, thus we can only silently mark the qgroup
inconsistent.
Anyway, user shouldn't use qgroup inheritance during snapshot creation,
and should add qgroup relationship after snapshot creation by 'btrfs
qgroup assign', which has a much better UI to inform user about qgroup
inconsistent and kick in rescan automatically.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
