On some devices that only support static rate fallback tables sending rate
control probing packets can be really expensive.
Probing lower rates can already hurt throughput quite a bit. What hurts even
more is the fact that on mt76x0/mt76x2, single probing packets can only be
forced by directing packets at a different internal hardware queue, which
causes some heavy reordering and extra latency.
The reordering issue is mainly problematic while pushing lots of packets to
a particular station. If there is little activity, the overhead of probing is
neglegible.
The static fallback behavior is designed to pretty much only handle rate
control algorithms that use only a very limited set of rates on which the
algorithm switches up/down based on packet error rate.
In order to better support that kind of hardware, this patch implements a
different approach to rate probing where it switches to a slightly higher rate,
waits for tx status feedback, then updates the stats and switches back to
the new max throughput rate. This only triggers above a packet rate of 100
per stats interval (~50ms).
For that kind of probing, the code has to reduce the set of probing rates
a lot more compared to single packet probing, so it uses only one packet
per MCS group which is either slightly faster, or as close as possible to
the max throughput rate.
This allows switching between similar rates with different numbers of
streams. The algorithm assumes that the hardware will work its way lower
within an MCS group in case of retransmissions, so that lower rates don't
have to be probed by the high packets per second rate probing code.
To further reduce the search space, it also does not probe rates with lower
channel bandwidth than the max throughput rate.
At the moment, these changes will only affect mt76x0/mt76x2.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On hardware with static fallback tables (e.g. mt76x2), rate probing attempts
can be very expensive.
On such devices, avoid sampling rates slower than the per-group max throughput
rate, based on the assumption that the fallback table will take care of probing
lower rates within that group if the higher rates fail.
To further reduce unnecessary probing attempts, skip duplicate attempts on
rates slower than the max throughput rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The group number needs to be multiplied by the number of rates per group
to get the full rate index
Fixes: 5935839ad7 ("mac80211: improve minstrel_ht rate sorting by throughput & probability")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
he_spr_ie_elem is dereferenced before the NULL check. fix this by moving
the assignment after the check.
fixes commit 697f6c507c ("mac80211: propagate HE operation info into
bss_conf")
This was reported by the static code checker.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190813070712.25509-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Report timestamp for when sta becomes associated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20190809180001.26393-2-greearb@candelatech.com
[fix ktime_get_boot_ns() to ktime_get_boottime_ns(), assoc_at type to u64]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the 802.11ax specification a new band is introduced, which
is also proposed by FCC for unlicensed use. This band is referred
to as 6GHz spanning frequency range from 5925 to 7125 MHz.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-2-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code generating the Tx Radiotap header when using tx_status_ext was
missing a field increment after setting the VHT bandwidth.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-4-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reporting 80MHz, we need to set 4 and not 2 inside the corresponding
field inside the Tx Radiotap header.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-3-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reporting legacy rates inside the TX Radiotap header we need to split
the check between "uses tx_statua_ext" and "is legacy rate". Not doing so
would make the code drop into the !tx_status_ext path.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RX Radiotap header length was not calculated properly when reporting
legacy rates using tx_status_ext.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of HE AP-STA link, ieee80211_send_nullfunc() will not
send the QOS NULL packet to check if AP is still associated.
In this case, probe_send_count will be non-zero and
ieee80211_sta_work() will later disassociate the AP, even
though no packet was ever sent.
Fix this by decrementing probe_send_count and not calling
ieee80211_send_nullfunc() in case of HE link, so that we
still wait for some time for the AP beacon to reappear and
don't disconnect right away.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Link: https://lore.kernel.org/r/20190703131848.22879-1-shay.bar@celeno.com
[clarify commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Store the OBSS PD parameters inside bss_conf when bringing up an AP and/or
when a station connects to an AP. This allows the driver to configure the
HW accordingly.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190730163701.18836-3-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This came up in fuzz testing, and really we don't consider
all-zeroes to be a valid MAC address in most places, so
also reject it here to avoid confusion later on.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Link: https://lore.kernel.org/r/1563959770-21570-1-git-send-email-periyasa@codeaurora.org
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The return from ieee80211_get_sband can potentially be a null pointer, so
it seems prudent to add a null check to avoid a null pointer dereference
on sband.
Addresses-Coverity: ("Dereference null return")
Fixes: 2ab4587675 ("mac80211: add support for the ADDBA extension element")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190730143205.14261-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert this for now, it has been reported multiple times that it
completely breaks connectivity on various devices.
Cc: stable@vger.kernel.org
Fixes: 8dbb000ee7 ("mac80211: set NETIF_F_LLTX when using intermediate tx queues")
Reported-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Peter Lebbing <peter@digitalbrains.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HE allows peers to negotiate the aggregation fragmentation level to be used
during transmission. The level can be 1-3. The Ext element is added behind
the ADDBA request inside the action frame. The responder will then reply
with the same level or a lower one if the requested one is not supported.
This patch only handles the negotiation part as the ADDBA frames get passed
to the ATH11k firmware, which does the rest of the magic for us aswell as
generating the requests.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190729104512.27615-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upon a successful assoc a station shall store the content of the HE
operation element inside bss_conf so that the driver can setup the
hardware accordingly.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190729102342.8659-2-john@phrozen.org
[use struct copy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a very similar spirit to commit c470bdc1aa ("mac80211: don't WARN
on bad WMM parameters from buggy APs"), an AP may not transmit a
fully-formed WMM IE. For example, it may miss or repeat an Access
Category. The above loop won't catch that and will instead leave one of
the four ACs zeroed out. This triggers the following warning in
drv_conf_tx()
wlan0: invalid CW_min/CW_max: 0/0
and it may leave one of the hardware queues unconfigured. If we detect
such a case, let's just print a warning and fall back to the defaults.
Tested with a hacked version of hostapd, intentionally corrupting the
IEs in hostapd_eid_wmm().
Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190726224758.210953-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the basics required for supporting high efficiency with mesh:
include HE information elements in beacons, probe responses, and peering
action frames, and check for compatible HE configurations when peering.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Forwarded: https://patchwork.kernel.org/patch/11029299/
Link: https://lore.kernel.org/r/20190724163359.3507-2-sven@narfation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add IEEE80211_KEY_FLAG_GENERATE_MMIE flag to ieee80211_key_flags in order
to allow the driver to notify mac80211 to generate MMIE and that it
requires sequence number generation only.
This is a preliminary patch to add BIP_CMAC_128 hw support to mt7615
driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/dfe275f9aa0f1cc6b33085f9efd5d8447f68ad13.1563228405.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to mac80211 for parsing SPR elements as per
P802.11ax_D4.0 section 9.4.2.241.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190618061915.7102-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to ieee80211_add_tx_radiotap_header() for handling rates
reported via ieee80211_tx_status. This allows us to also report HE rates.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190714154419.11854-4-john@phrozen.org
[remove text about 60 GHz, mac80211 doesn't support it, fix endianness issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 33d915d9e8 ("{nl,mac}80211: allow 4addr AP operation on
crypto controlled devices") has introduced a change which allows
4addr operation on crypto controlled devices (ex: ath10k). This
change has inadvertently impacted the interface combinations logic
on such devices.
General rule is that software interfaces like AP/VLAN should not be
listed under supported interface combinations and should not be
considered during validation of these combinations; because of the
aforementioned change, AP/VLAN interfaces(if present) will be checked
against interfaces supported by the device and blocks valid interface
combinations.
Consider a case where an AP and AP/VLAN are up and running; when a
second AP device is brought up on the same physical device, this AP
will be checked against the AP/VLAN interface (which will not be
part of supported interface combinations of the device) and blocks
second AP to come up.
Add a new API cfg80211_iftype_allowed() to fix the problem, this
API works for all devices with/without SW crypto control.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Fixes: 33d915d9e8 ("{nl,mac}80211: allow 4addr AP operation on crypto controlled devices")
Link: https://lore.kernel.org/r/1563779690-9716-1-git-send-email-mpubbise@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extended Key ID allows A-MPDU sessions while rekeying as long as each
A-MPDU aggregates only MPDUs with one keyid together.
Drivers able to segregate MPDUs accordingly can tell mac80211 to not
stop A-MPDU sessions when rekeying by setting the new flag
IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190629195015.19680-3-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1) Drop IEEE80211_HW_EXT_KEY_ID_NATIVE and let drivers directly set
the NL80211_EXT_FEATURE_EXT_KEY_ID flag.
2) Drop IEEE80211_HW_NO_AMPDU_KEYBORDER_SUPPORT and simply assume all
drivers are unable to handle A-MPDU key borders.
The new Extended Key ID API now requires all mac80211 drivers to set
NL80211_EXT_FEATURE_EXT_KEY_ID when they implement set_key() and can
handle Extended Key ID. For drivers not providing set_key() mac80211
itself enables Extended Key ID support, using the internal SW crypto
services.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190629195015.19680-2-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since ieee80211_tx_dequeue() must not be called with softirqs enabled
(i.e. from process context without proper disable of bottom halves),
we add a wrapper that disables bottom halves before calling
ieee80211_tx_dequeue()
The new function is named ieee80211_tx_dequeue_ni() just as all other
from-process-context versions found in mac80211.
The documentation of ieee80211_tx_dequeue() is also updated so it
mentions that the function should not be called from process context.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Link: https://lore.kernel.org/r/20190617200140.6189-1-erik.stromdahl@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The remove_sta_debugfs callback in struct rate_control_ops is no longer
used by any driver, as there is no need for it (the debugfs directory is
already removed recursivly by the mac80211 core.) Because no one needs
it, just remove it to keep anyone else from accidentally using it in the
future.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190612142658.12792-5-gregkh@linuxfoundation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_set_wmm_default() normally sets up the initial CW min/max for
each queue, except that it skips doing this if the driver doesn't
support ->conf_tx. We still end up calling drv_conf_tx() in some cases
(e.g., ieee80211_reconfig()), which also still won't do anything
useful...except it complains here about the invalid CW parameters.
Let's just skip the WARN if we weren't going to do anything useful with
the parameters.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190718015712.197499-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
The WEP code in the mac80211 subsystem currently uses the crypto
API to access the arc4 (RC4) cipher, which is overly complicated,
and doesn't really have an upside in this particular case, since
ciphers are always synchronous and therefore always implemented in
software. Given that we have no accelerated software implementations
either, it is much more straightforward to invoke a generic library
interface directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Based on 1 normalized pattern(s):
gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 58 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.556988620@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
-----BEGIN PGP SIGNATURE-----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=j+Um
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Many changes all over:
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
-----BEGIN PGP SIGNATURE-----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=AHi5
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes, all over:
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the offchannel TX wait time expires, send the appropriate event.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is not a good idea to try to perform any work (e.g. send an auth
frame) during reconfigure flow.
Prevent this from happening, and at the end of the reconfigure flow
requeue all the works.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multiple SSID cases, it takes time to prepare every AP interface
to be ready in initializing phase. If a sta already knows everything it
needs to join one of the APs and sends authentication to the AP which
is not fully prepared at this point of time, AP's channel context
could be NULL. As a result, warning message occurs.
Even worse, if the AP is under attack via tools such as MDK3 and massive
authentication requests are received in a very short time, console will
be hung due to kernel warning messages.
WARN_ON_ONCE() could be a better way for indicating warning messages
without duplicate messages to flood the console.
Johannes: We still need to address the underlying problem, but we
don't really have a good handle on it yet. Suppress the
worst side-effects for now.
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
[johannes: add note, change subject]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
