There is no need to restore and restart PCM streams in case ADSP didn't
reach reset and power off state during system suspend/resume cycle. In that
case stream is still active but paused and firmware doesn't allow allocating
a new stream before paused stream is freed.
ADSP remains active in case suspend sequence didn't go to suspend_late
stage. This can happen when either suspend sequence is aborted by a wakeup
or by letting only devices suspend by "echo devices >/sys/power/pm_test".
Currently stream restoring fails in these suspend cases. Fix this by adding
a flag that indicates is complete stream reinitialization needed or is it
enough to resume paused stream. Flag is set when we know that ADSP reached
suspend_late.
Initial fix to this issue came from Fang Yang. I modified it a little and
forward ported it to top of two other suspend/resume patches from me.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Borun Fu <borun.fu@intel.com>
Cc: yang fang <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove sst_byt_pcm_dev_resume() and move waiting of firmware boot into
sst_byt_pcm_dev_resume_early(). Now suspend_late and resume_early phases are
in sync with each other so that we know that ADSP was put into reset and was
unpowered after suspend_late and is ready to resume IO after resume_early
during resume stage in sst_byt_pcm_trigger().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge DSP reset and cleanup sequence in sst_byt_pcm_dev_suspend_noirq()
into sst_byt_pcm_dev_suspend_late(). First their order was wrong by first
unloading firmware modules in suspend_late and then taking DSP into reset
in suspend_noirq. Second ACPI has put device into OFF state already during
suspend_late so trying to reset the DSP is a no-op at suspend_noirq stage.
Fix these by moving DSP reset and cleanup into
sst_byt_pcm_dev_suspend_late() before firmware unloading.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Update the initial Baytrail ADSP firmware file name with the one that is now
in linux-firmware.git. Please see linux-firmware.git commit 7551a3a78453
("fw_sst_0f28: Add firmware for Intel Baytrail SST DSP").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Only update the stream when the IPC message type matches stream type.
Signed-off-by: Paweł Piskorski <pawel.piskorski@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make sure we dont issue IPC when we are processing a response.
Signed-off-by: Paweł Piskorski <pawel.piskorski@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes a bug where we dont delete the current message when an
IPC message timeout occurs.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add dependency to DW_DMAC for broadwell machine, which
have built in DW dma engines.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Platform data may be null during platform_device_add. Allocate platform
data before using.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Check ops pointer members before we can derefference them.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add some debugging info to help with Dx state debug.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add trace notification of IPC stream reset.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add some register definitions for other shim register bits.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
HMDC is the correct naming for this register.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Broadwell based machines with SST DSP audio.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Update FW version readback. IPC_GLB_GET_FW_VERSION reads back
the ABI version whilst the release version is in the mailbox.
Update to use mailbox version for info logging.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The sst-haswell-dsp.c is an ACPI independent file, this patch removes
ACPI header files for it.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This interface will be used by subsequent patches to set/get parameters from DSP
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DSP returns error codes for IPC return so add them in driver
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
the shim registers start and end can be useful while parsing the shim addresses,
so add these
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge D-SRAM0 D-SRAM1 D-SRAM2 to D-SRAM, for wild cat point ADSP mem regions.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add dummy read after each block enable, to workaround
SRAM write missing bytes issue.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This change removes unsupported formats from System,
Capture and Loopback FE DAIs.
Also it fixes S24_LE support on all DAIs.
While at this fix 24 bit flag for BYT as well.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Kernel should not enable/disable speakers and digital microphone whenever
jack is inserted/removed. This is more use-case than kernel specific
decision. For instance one may want to play VoIP ring tones using both
speakers and headphone but play music only from one of them.
Because of above reason remove "Ext Spk" and "Int Mic" update when jack
state is changed. Also this update was illogical anyway: "Ext Spk" was
enabled when jack was inserted and disabled when jack was removed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It turned out there is no need to enable microphone detection in MAX98090
codec. Headset microphone is anyway detected by a GPIO signal from another
chip and headset button presses cannot be detected either because a signal
needed for it is not connected.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pass actual jack type bitmask to snd_soc_jack_new() in order to report
also microphone detections and not only headphone. While at it change also
jack name and pass also SND_JACK_LINEOUT type.
Reported-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Headset jack has only mono microphone input.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mic detect GPIO is active low when headset microphone is detected. Found
both by debugging and checking the schematics.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move "MICBIAS" as a supply widget to "Headset Mic" instead of keeping it
between input pin "IN34" and "Headset Mic".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As added in previosu patch along with stream to piep conversion si required for
compressed audio too
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merrifield DSP used various pipelines to identify the streams and processing
modules. Add these defination in the pcm driver and also add a table for device
entries to firmware pipeline id conversion
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Tis will be used to add table based support for pcm front ends in subsequent
patches
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This will be used to update current driver as well as in support for the mrfld
patches
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now the DSP is capable of reporting the delay, report it to upper layers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The argument was called mad_substream which is no longer apt as older driver
is not used anymore so rename as arg
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This helps us to handle pcm and compress ops seperately and per dai
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Connect "Headset Mic" to "MICBIAS1" supply widget of RT5640 in order to
enable bias voltage for headset microphones.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DSP initialization complete message IPC_IA_FW_INIT_CMPLT is a large message
carrying firmware details in mailbox. Read and show those details during
init in order to be able to get that information to QA reports.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use card PM ops from ASoC core instead of defining custom PM ops here since
we are calling anyway common suspend/resume callbacks.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify byt-rt5640.c and haswell.c machine drivers by using
devm_snd_soc_register_card(). Remove also needless dev_set_drvdata()
from byt_rt5640_probe() since snd_soc_register_card() does it too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A few files contain duplicate headers. This patch removes the second entry of
duplicate in each file under question.
There is no functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Stored DSP DMA pointer must be cleared before starting the stream since
PCM pointer callback sst_byt_pcm_pointer() can be called before pointer is
updated. In that case last position of previous stream was wronly returned.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Baytrail and Haswell SST IPC don't stop the kernel thread in error and
cleanup path thus leaving orphan kernel thread behind in such a case.
Also while at it, fix one error path in sst-haswell-ipc.c that doesn't free
hsw->msg.
[Jarkko: I edited the commit log a little]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
