The 'big-endian-data' property is originally used to indicate whether the
LSB firstly or MSB firstly will be transmitted to the CODEC or received
from the CODEC, and there has nothing relation to the memory data.
Generally, if the audio data in big endian format, which will be using the
bytes reversion, Here this can only be used to bits reversion.
So using the 'lsb-first' instead of 'big-endian-data' can make the code
to be readable easier and more easy to understand what this property is
used to do.
This property used for configuring whether the LSB or the MSB is transmitted
first for the fifo data.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SAI supports these operation modes:
1) asynchronous mode
Both Tx and Rx are set to be asynchronous.
2) synchronous mode (Rx sync with Tx)
Tx is set to be asynchronous, Rx is set to be synchronous.
3) synchronous mode (Tx sync with Rx)
Rx is set to be asynchronous, Tx is set to be synchronous.
4) synchronous mode (Tx/Rx sync with another SAI's Tx)
5) synchronous mode (Tx/Rx sync with another SAI's Rx)
* 4) and 5) are beyond this patch because they are related with another SAI.
As the initial version of this SAI driver, it supported 2) as default while
the others were totally missing.
So this patch just adds supports for 1) and 3).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds software reset code in dai_probe() so as to make a true init
by clearing SAI's internal logic, including the bit clock generation, status
flags, and FIFO pointers.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SAI mainly has the following clocks:
bus clock
control and configure registers and to generate synchronous
interrupts and DMA requests.
mclk1, mclk2, mclk3
to generate the bit clock when the receiver or transmitter is
configured for an internally generated bit clock.
So this patch adds these clocks and their clock controls to the driver.
[ To concern the old DTB cases, I've added a bit of extra code to make
the driver compatible with them. And by marking clock NULL if failed
to get, the clk_prepare() or clk_get_rate() would easily return 0
so no further path should be broken. -- by Nicolin ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The next coming i.MX6 Solo X SoC also contains SAI module while we use
imp_pcm_init() for i.MX platform.
So this patch adds one compatible route for imx6sx and updates the DT
doc accordingly.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We only enable one side interrupt for each stream since over/underrun
on the opposite stream would be resulted from what we previously did,
enabling TERE but remaining FRDE disabled, even though the xrun on the
opposite direction will not break the current stream.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current trigger() has two crucial problems:
1) The DMA request enabling operations (FSL_SAI_CSR_FRDE) for Tx and Rx are
now totally exclusive: It would fail to run simultaneous Tx-Rx cases.
2) The TERE disabling operation depends on an incorrect condition -- active
reference count that only gets increased in snd_pcm_open() and decreased
in snd_pcm_close(): The TERE would never get cleared.
So this patch overwrites the trigger function by following these rules:
A) We continue to support tx-async-while-rx-sync-to-tx case alone, which's
originally limited by this fsl_sai driver, but we make the code easy to
modify for the further support of the opposite case.
B) We enable both TE and RE for PLAYBACK stream or CAPTURE stream but only
enabling the DMA request bit (FSL_SAI_CSR_FRDE) of the current direction
due to the requirement of SAI -- For tx-async-while-rx-sync-to-tx case,
the receiver is enabled only when both the transmitter and receiver are
enabled.
Tested cases:
a) aplay test.wav -d5
b) arecord -r44100 -c2 -fS16_LE test.wav -d5
c) arecord -r44100 -c2 -fS16_LE -d5 | aplay
d) (aplay test2.wav &); sleep 1; arecord -r44100 -c2 -fS16_LE test.wav -d1
e) (arecord -r44100 -c2 -fS16_LE test.wav -d5 &); sleep 1; aplay test.wav -d1
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It's quite cricial to clear error flags because SAI might hang if getting
FIFO underrun during playback (I haven't confirmed the same issue on Rx
overflow though).
So this patch enables those irq and adds isr() to clear the flags so as to
keep playback entirely safe.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
o Add SND_SOC_DAIFMT_DSP_A support.
o Add SND_SOC_DAIFMT_DSP_B support.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This adds Freescale SAI ASoC Audio support.
This implementation is only compatible with device tree definition.
Features:
o Supports playback/capture
o Supports 16/20/24 bit PCM
o Supports 8k - 96k sample rates
o Supports master and slave mode.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
