The WM1811 DC servo is able to run much faster than previous devices so
the benefit of skipping calibration is not useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using snd_soc_write() means we always write to the register even if it
already contains the newly calculated value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Similar to what commit 1e3ad57 (ASoC: Remove redundant -codec from
WM8776 driver name) does for wm8776 driver, this patch does the same
thing for cs4270 driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the cache is currently open coded this is more of a win than for
most devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Don't use the internal I/O functions directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Early revisions of several of the WM8994 variants have register updates
to improve performance. Move these over to using the regmap patch system
instead of open coding them in the audio driver. Since the regmap init
is done by the MFD the code is moved there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
When an external capacitor is connected to MICBIAS2 on devices with
jack detection (which is not required but may be done in some systems)
then the loading may mean that better performance is obtained when
the microphone bias is enabled normally rather than using the low power
mode. Provide platform data allowing systems to indicate if they require
this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This minimises the chance of any external capacitors that are fitted
being discharged into headphones as they insert.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current ak4642 driver had wrong dapm settings for headphone L/R.
If you select headphone L, and select R after that,
headphone L setting was removed by R settings.
This patch fixes it up.
It provides just "Headphone Enable" to user side
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the printk(KERN_ERR* instances with dev_err in the driver.
While we are here clean up some of the debug messages as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8775 is register compatible with the WM8776 so can be supported with
the same driver though it is an ADC only part. Add the device ID to the
WM8776 driver, further updates will be added in the future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While it matches the current code only bringing the device out of reset
isn't actually doing what the function says so make sure we set the GPIO
high before we pull it low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows userspace control of final power off, allowing policy decisions
for register configuration retention.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only enable and disable the FLL when explicitly told to, supporting some
additional use cases and making the driver behaviour more standard.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we update for any changes in cases where we reconfigure while
live (eg, for analogue bypass).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Show the id we read when the id mismatch is detected.
This is useful for debugging.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The main role of the WM9081 is as a class D speaker amplifier so there
is no concern about pops. There are also very few registers and a fast
power up time so we can happily mark the driver as idle_bias_off.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Raise the ramp time to 50ms to cover corner cases, use the startup bias
generator, explicitly reset the ramp circuit when complete and reorder
things all of which should improve performance somewhat for systems that
are sensitive to noise from VMID.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The enable of the single ended line outputs on wm_hubs devices performs
better if the output is enabled prior to starting VMID. Since inactive
outputs are held at VMID anyway there is little cost to doing this for
unused outputs. Add callbacks into wm_hubs and keep track of which outputs
are really active so we can disable them once we're active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the mixer path diagram input sources' attenuators logically
belong to the playback path and DMIC boost only affects capture.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This brings the TLVs in sync with the documentation and allows to properly
manipulate mic boost controls with alsamixer.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch should fix output through speakers using HP mixer.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix I2S digital interface power for recording.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DMIC switches and controls to ALC5632 codec.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no Phone Mix<->Mono Mix route in datasheet.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename capture switches to common scheme XXX2REC.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove extra zero from volume step in DECLARE_TLV_DB_SCALE macro.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct spelling "memroy" to "memory" in
sound/soc/codecs/twl4030.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. the number of the half-beast?
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPMzv8AAoJEHm+PkMAQRiGgeYIAJxxGCxSMLRIiPaGRmQbWifs
eE3z6AUWitGfYvhmYdWVz+C/aa4pPCVWr3bAFxUQhu+ESmiFIiqiefvlTRf5f84e
pcoJFobkFfhtK4gLvUr75WxXDFq/1HhKqW1OLzIW4gQsnhMdjGJ3lLK6ZoRYH8h4
cGoN3DRII9mVLFcB2sgbeRvbQBA/O4n0aOQ2ryZkCcPQQMIKhR/rUEEV2pe/ovHE
rumQgI3PVey816P4e5YnOvrEAllFZlaZ/F0ClJgNdfeQCVTZx9KNRbiNxHi6fcC5
6Zgg7e5EvQTAy7QqQZ0hmS4k4CFmnswX3Nm+ZabRNqBdLSjPEDD9hk1o1dodYCg=
=BBLC
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc3' as we've got several bugfixes in there which are
colliding annoyingly with development.
Linux 3.3-rc3
.. the number of the half-beast?
Conflicts:
sound/soc/codecs/wm5100.c
sound/soc/codecs/wm8994.c
It's set unconditionally.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The VMID ramp rate is supposed to be 0x3, not 11b. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Make sure we generate enough BCLKs for I2S style modes by always having
a minimum of two channels worth of clocks for the BCLK.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No practical impact but now we have the control type we may as well use
it for the slightly nicer sequencing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we're not implementing GPIO or microphone detection support
there's no users for the read() function any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Make the mechanism used for WM8994 more like that for WM1811 and WM8958:
provide the logic to distinguish between headphone and headset and hard
code the reporting of sensible SND_JACK values. Should integration with
other detection mechanisms be required we can add appropriate callbacks
(though some integrations should be able to use the subsystem ones).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we might get an error if the GPIO is configured as an input
since that makes the register volatile and a suspended device can't be
read from.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the default state that the runtime PM infrastructure expects so
instead just kick the runtime PM core to suspend us if we're not doing
anything (as is default).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix build breakage by using the correct API call to add kcontrols.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Looks like nobody is or will be using this code.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In cases where we should enter STANDBY DAPM will power us up, otherwise
there is no need to power up and we can remain in OFF.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can enable VMID independently of the bias in some use cases so we need
to ensure that the core device is powered up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The second line output mixer has the controls for the line input bypasses
in the opposite order.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
For master mode, set Output [X|A|V]SP_SCLK Sourcing Mode to MCLK Mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. several days delayed. No reason, I just didn't think of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPKF4KAAoJEHm+PkMAQRiGw/YH+wXg2DpZUuHeBK52zMGlJBPc
DzX11/Uan3Y07gM0JbDzuVxwjX4vdxR2bV6r1qsLP8JEUnE8jyFC32DBGi5WAht7
F4KU/Uov2Ds5/wzvY4Iuo01C+JftQHXuy/Sbhck1d0LI0yjLejRaw+zuJv0x2/eS
7YqV+KTGE1lDuJs/Gyq1Vqr1g9831AuS1tv/g3gaqBuN6TcPBFCocaVxzwrUc+y6
94h26XbbOhQRIz38oqUkiqAGnvYS61ocyBcEiRHf0dXkNSDIINqlgukvd7YTXouA
jj/w/DWpMRcQuYAgqkrurr9+yWC9hVQcsvvQ5sAQnIPcxoR868sg1pO8Oheq+1g=
=kUzV
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc2' into for-3.4
A reasonable amount of new development is causing fiddly merge conflicts
between different resource management changes (mostly fixing bugs in
resource management due to noticing things while doing enhancements in
the same area).
Linux 3.3-rc2
.. several days delayed. No reason, I just didn't think of it.
For later wm_hubs devices we have much less need to keep the biases up
even when using single ended line outputs so flag idle_bias_off for
everything except the WM8993 and WM8994.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now we've switched over to regmap the ASoC level cache sync will be
ineffectual and potentially harmful as there is no longer an ASoC level
cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
IN1L/R is routed to both line output mixers, we don't route IN1 to LINEOUT1
and IN2 to LINEOUT2.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The Mute Switch should be called Playback Switch to match the volume
and the regmap core has been updated so we don't need to mark all the
registers as non-volatile.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC
drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver
for devices can unconditionally support idle_bias_off.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For optimal performance the single ended line outputs require that the
line output VMID buffer be enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Report any accessory with a low impedance as a headphone, previously
anything other than a short or microphone would not be reported at all.
The most likely reason is a microphone with incorrect polarity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using pm_runtime to decide if the device should go into full power down
has the dual advantage of allowing easier integration with non-DAPM
reasons to power on the device (like the FLL) and allowing userspace to
control the final power down which is useful for tuning retention of
DSP firmware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to avoid breakage change the omap-abe-twl6040
machine driver's routing.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to write the configuration for each microphone to a different
register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
When we have identified an accessory make sure we've flagged that we've
done so in order to make sure we always report buttons and don't continue
to polarity flip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the hardware is configured with one or both of the IN4 inputs used
for DC measurement (with no DC blocking capacitor connected) then we can
improve power consumption slightly in idle modes by applying a register
write sequence. Provide platform data to enable this, implemented using
a regmap patch.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In wm2000_i2c_probe(), if we take the true branch in
"
ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_wm2000,
NULL, 0);
if (ret != 0)
goto err_fw;
"
then we'll release_firmware(fw) at the 'err_fw' label. But we've already
done that just a few lines above. That's a use-after-free bug.
This patch restructures the code so that we always call
release_firmware(fw) before leaving the function, but only ever call
it once.
This means that we have to initialize 'fw' to NULL since some paths
may now end up calling it without having called request_firmware(),
but since request_firmware() deals gracefully with NULL pointers, we
are fine if we just NULL initialize it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To print a value of type size_t one should use %zd, not %d.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below build warning when CONFIG_HOTPLUG is not set.
CC sound/soc/codecs/alc5623.o
sound/soc/codecs/alc5623.c:1062: warning: ‘alc5623_i2c_remove’ defined but not used
CC sound/soc/codecs/alc5632.o
sound/soc/codecs/alc5632.c:1112: warning: ‘alc5632_i2c_remove’ defined but not used
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to table based DAPM and control init.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should be allowing a 5ms delay after the charge pump is started in
order to ensure it has finished ramping.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The problem was introduced due to the obscure formatting some of the
older drivers use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is more what the device model wants us to do and will allow use by
non-audio functions before the audio part of the device has come up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will allow us to move the interrupt allocation out of the ASoC part
of the driver and simplifies the locking by removing any reliance in the
bulk of the interrupt path on the big CODEC lock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Throughout the sgtl5000 driver source code and also in the sgtl5000 datasheet
the revision code is shown in hexadecimal.
Print it hex format, for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If an interrupt is supplied then use it for thermal warning and FLL lock
notifications. When using the interrupt raise the timeout for the FLL lock
substantially to reduce the chances of spurious warnings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This must be a leftover from a previous driver.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Much more compact, both in terms of source and especially in terms of
RAM used at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
remove unnecessary inclusion of machine specific header
file mach/dm365.h from cq93vc.c voice codec driver
which comes in the way of platform code consolidation.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a method for mach drivers to query the HS DC offset step size in mV.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The register map for this device is actually fairly sparse so the rbtree
should be beneficial.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensures that we get control of the CODEC earlier and don't try to probe
the card at all if register I/O isn't working.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Helps push the register cache code down out of ASoC and improves resume
times by using the more efficient regmap cache sync code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With a low frequency SYSCLK and a fast I2C clock register synchronisation
may occasionally take too long to take effect, causing I/O issues. Disable
synchronisation in order to avoid any issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
These are all to either uncached registers or fixes to register defaults,
in the former case the cache won't do anything and in the latter case
we're fixing things so the cache sync will do the right thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Writing to the registers won't work if we do actually manage to hit a fully
powered off state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Register LDOCTLEN must always be initialized to clear the analog power
control bit, otherwise the analog block will stay deactivated.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dividers (such as MDAC) are always needed, independent of the codec
being I2S master or slave. Needed on a custom board where the codec has
to be slave.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct SGTL5000_CHIP_CLK_CTRL to SGTL5000_CHIP_REF_CTRL in
sgtl5000_restore_regs(), and add comment to explain the
restore order.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Zeng Zhaoming <zengzm.kernel@gmail.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
ALSA: usb-audio: add Yamaha MOX6/MOX8 support
ALSA: virtuoso: add S/PDIF input support for all Xonars
ALSA: ice1724 - Support for ooAoo SQ210a
ALSA: ice1724 - Allow card info based on model only
ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
ALSA: hdspm - Provide unique driver id based on card serial
ASoC: Dynamically allocate the rtd device for a non-empty release()
ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
ALSA: hda/cirrus - support for iMac12,2 model
ASoC: cx20442: add bias control over a platform provided regulator
ALSA: usb-audio - Avoid flood of frame-active debug messages
ALSA: snd-usb-us122l: Delete calls to preempt_disable
mfd: Put WM8994 into cache only mode when suspending
...
Fix up trivial conflicts in:
- arch/arm/mach-s3c64xx/mach-crag6410.c:
renamed speyside_wm8962 to tobermory, added littlemill right
next to it
- drivers/base/regmap/{regcache.c,regmap.c}:
duplicate diff that had already come in with other changes in
the regmap tree
The DL1 PDM interface adds a little gain depending on the output device.
Add a method to retrieve the gain value for machine driver usage.
Signed-off-by: Liam Girdwood <lrg@ti.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (40 commits)
regulator: set constraints.apply_uV to 0 in of_get_fixed_voltage_config
regulator: max8925: fix enabled/disabled judgement mistake
regulator: add regulator_bulk_force_disable function
regulator: pass regulator_register of_node in fixed voltage driver
regulator: add regulator_force_disable() definition for !CONFIG_REGULATOR
regulator: Enable supply regulator if child rail is enabled.
regulator: mc13892: Convert to devm_kzalloc()
regulator: mc13783: Convert to devm_kzalloc()
regulator: Fix checking return value of create_regulator
regulator: Fix the error handling if create_regulator fails
regulator: Export regulator_is_supported_voltage()
regulator: mc13892: add device tree probe support
regulator: mc13892: remove the unnecessary prefix from regulator name
regulator: Convert wm831x regulator drivers to devm_kzalloc()
regulator: da9052: Staticize non-exported symbols
regulator: Replace kzalloc with devm_kzalloc and if-else with a switch-case for da9052-regulator
regulator: Update da9052-regulator for DT changes
regulator: DA9052/53 Regulator support
regulator: pass device_node to of_get_regulator_init_data()
regulator: If a single voltage is set with device tree then set apply_uV
...
Now that a regulator device for controlling the codec chip reset state
over a platform agnostic regulator API is available on the only board
using this driver so far, extend the driver with a bias control function
which will request virtual power to the codec chip from that virtual
regulator, and will supersede the present implementation existing at the
sound card level.
Thanks to the regulator sharing mechanism, both the old (the sound card)
and the new (the codec) implementations should coexist smoothly until
the sound card file is updated. For this to work as expected, update the
sound card .set_bias_level callback to not touch codec->dapm.bias_level.
While extending the cx20442 structure, drop unused control_type member.
Created against linxu-3.2-rc6, tested on top of patch 1/4 "ARM: OMAP1:
ams-delta: set up a regulator over the modem reset GPIO pin".
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
For a given ir and fs, there is at most one possible match for the case
mclk_ratios[ir][j].ratio * fs == freq.
Thus we can break from the inner loop once a match is found.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DA7210 has three line inputs (AUX1 Left, AUX1 Right and AUX2) and
a stereo MIC. This patch adds gain controls for MIC, AUX1, AUX2 as
well as INPGA.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert sgtl5000 codec driver to use devm_kzalloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
vdda, vddio and vddd are voltages expressed in milivolts (mV), so use the
proper annotation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Broken in commit d1dc698a54
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
