* Add an extra argument to ide_max_dma_mode() for passing requested transfer
mode. Use it as an upper limit when finding the best DMA for device/host.
* Rename ide_max_dma_mode() to ide_find_dma_mode() and at the same time add
ide_max_dma_mode() wrapper which passes XFER_UDMA_6 as a requested mode to
ide_find_dma_mode(). Also add inline ide_find_dma_mode() version for
CONFIG_BLK_DEV_IDEDMA=n case.
* Pass requested transfer mode from ide_find_dma_mode() to ide_get_mode_mask()
to avoid false warning from eighty_ninty_three().
* Use ide_find_dma_mode() to limit the user requested transfer mode in
ide_rate_filter(). Also limit the requested mode by host max PIO mode.
Above changes make ide_rate_filter() to:
* Clip desired transfer mode down if it is invalid (values 0x0F, 0x13-0x19
and 0x25-0x39, values > 0x46 were already clipped down, same for values
0x25-0x39 but iff UDMA was not supported by the host).
* Clip desired transfer mode down if it is currently unsupported by IDE core
(PIO6 and MWDMA3-4, the latter were already clipped down but iff UDMA was
not supported by the host).
* Clip desired transfer mode down according to the host capabilities
(UDMA modes were already clipped down but MWDMA/SWDMA/PIO weren't,
also ->atapi_dma flag was not respected).
* Clip desired transfer mode down according to the device capabilities
(except PIO modes for now which require mode work) - shouldn't be a
problem since ide_set_xfer_rate() is called _after_ device has accepted
given transfer mode.
and also result in a number of host driver specific bugfixes:
* icside
- clip unsupported PIO5 mode down
- fix unsupported/invalid modes being set in drive->current_speed
* ide-cris
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
- fix BUG() on unsupported/invalid modes
* au1xxx-ide
- clip unsupported PIO5, SWDMA0-2 and MWDMA0-2
(if BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=n) modes down
* aec62xx
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
- fix 0x00 being programmed as PIO timing for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* alim15x3
- clip DMA modes down for ATAPI devices (chipset revision == 0x20 only)
- fix theoretical OOPS for 0x0F mode
- fix unsupported/invalid modes being set on the device
* amd74xx
- clip unsupported SWDMA0-2 (on COBRA_7401 revs <= 7) modes down
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* atiixp
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix cached MWDMA mode being cleared for unsupported/invalid modes
- fix PIO{0,2} timings being programmed for unsupported/invalid modes
- fix theoretical OOPS for PIO5-6 and 0x0F modes
- fix unsupported/invalid modes being set on the device
* cmd64x
- clip unsupported SWDMA0-2 modes down
* cs5530
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix BUG() on unsupported/invalid modes
(which happened if the device accepted the setting)
* cs5535
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix theoretical OOPS for PIO5-6 and 0x0F modes
* hpt34x
- clip DMA modes down for ATAPI devices
- fix invalid timings being programmed for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* hpt366
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix PIO0 timings being programmed for unsupported/invalid modes
- fix DMA timings being cleared for MWDMA3-4 and 0x25-0x39 modes
- fix unsupported/invalid modes being set on the device
* it8213
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* it821x
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
(chipset in smart mode and revision 0x10 in pass-through mode)
* jmicron
- clip unsupported SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
* pdc202xx_new
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
* pdc202xx_old
- clip unsupported PIO5 mode down
- fix incorrect timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* piix
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* sc1200
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix BUG() on unsupported/invalid modes
(which happened if the device accepted the setting)
* scc_pata
- clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 modes down
* serverworks
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix DMA/UDMA timings/settings being cleared for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* siimage
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices (SATA chipsets)
* sis5513
- clip unsupported PIO5 mode down
- fix BUG() on unsupported/invalid modes
* sl82c105
- clip unsupported SWDMA0-2 modes down
* slc90e66
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* tc86c001
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix PIO0 timings being programmed for PIO5/0x0F/SWDMA0-2/0x13-0x19 modes
- fix invalid 0x00 DMA timing being programmed for MWDMA3-4/0x25-0x39 modes
- fix unsupported/invalid modes being set on the device
* triflex
- clip unsupported PIO5 mode down
* via82cxxx
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* pmac
- clip unsupported PIO5 and SWDMA0-2 modes down
* cmd640/ht6560b
- clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
- fix PIO5 being clipped to PIO4 (if CONFIG_BLK_DEV_IDEDMA=n)
* opti621
- clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
- clip unsupported PIO4 to PIO3 (if CONFIG_BLK_DEV_IDEDMA=n)
While at it:
* Use ide_rate_filter() in cs5520.c::cs5520_tune_chipset().
* Remove no longer needed checks from hpt366.c::hpt3{6,7}x_tune_chipset().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ACPI spec defines the sequence of IDE power on/off:
Powering down:
Call _GTM.
Power down drive (calls _PS3 method and turns off power planes).
Powering up:
Power up drive (calls _PS0 method if present and turns on power planes).
Call _STM passing info from _GTM (possibly modified), with ID data from
each drive.
Initialize the channel.
May modify the results of _GTF.
For each drive:
Call _GTF.
Execute task file (possibly modified).
This patch adds the missed _PS0/_PS3 methods call.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the MWDMA modes (at least that could be seen in their so-called drivers :-),
so the driver needs to account for this -- to achieve this:
- add mdma_filter() method from the original patch by Bartlomiej Zolnierkiewicz
with his consent;
- install the method for all chips to only return empty mask if a SATA drive
is detected on HPT372{AN]/374 chips...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the corgi backlight driver to a more generic version
so it can be reused by other code rather than being Zaurus/PXA
specific.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
I get a compilation error in sglist-arch branch
with BLK_DEV_IO_TRACE=n:
CC block/compat_ioctl.o
/usr0/export/dev/bharrosh/git/pub/linux-2.6-block/block/compat_ioctl.c: In
function ?compat_blk_trace_setup?:
/usr0/export/dev/bharrosh/git/pub/linux-2.6-block/block/compat_ioctl.c:568:
error: expected expression before ?do?
make[2]: *** [block/compat_ioctl.o] Error 1
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
As discussed before, this patch provides userland with a way to access
relevant options in Router Advertisements, after they are processed
and validated by the kernel. Extra options are processed in a generic
way; this patch only exports RDNSS options described in RFC5006, but
support to control which options are exported could be easily added.
A new rtnetlink message type is defined, to transport Neighbor
Discovery options, along with optional context information. At the
moment only the address of the router sending an RDNSS option is
included, but additional attributes may be later defined, if needed by
new use cases.
Signed-off-by: Pierre Ynard <linkfanel@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix: Swap comments for dev_put() and dev_hold() to get them
at the right place.
Typo introduced by 4fa57c9ea9f36f9ca852f3a88ca5d2f1aebbc960.
Signed-of-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch make processing netlink user -> kernel messages synchronious.
This change was inspired by the talk with Alexey Kuznetsov about current
netlink messages processing. He says that he was badly wrong when introduced
asynchronious user -> kernel communication.
The call netlink_unicast is the only path to send message to the kernel
netlink socket. But, unfortunately, it is also used to send data to the
user.
Before this change the user message has been attached to the socket queue
and sk->sk_data_ready was called. The process has been blocked until all
pending messages were processed. The bad thing is that this processing
may occur in the arbitrary process context.
This patch changes nlk->data_ready callback to get 1 skb and force packet
processing right in the netlink_unicast.
Kernel -> user path in netlink_unicast remains untouched.
EINTR processing for in netlink_run_queue was changed. It forces rtnl_lock
drop, but the process remains in the cycle until the message will be fully
processed. So, there is no need to use this kludges now.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink_sendskb does not use third argument. Clean it and save a couple of
bytes.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rest of the miscellaneous code required to support the
5761.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the duplicate ipv6_{auth,esp,comp}_hdr structures since
they're identical to the IPv4 versions. Duplicating them would only create
problems for ourselves later when we need to add things like extended
sequence numbers.
I've also added transport header type conversion headers for these types
which are now used by the transforms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return type of crypto_*_reqsize from int to
unsigned int which matches what the underlying type is (and should
be).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since not everyone needs a queue pointer and those who need it can
always get it from the context anyway the queue pointer in the
common alg object is redundant.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds support for having multiple parameters to
a template, separated by a comma. It also adds support
for integer parameters in addition to the current algorithm
parameter type.
This will be used by the authenc template which will have
four parameters: the authentication algorithm, the encryption
algorithm, the authentication size and the encryption key
length.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds crypto_aead which is the interface for AEAD
(Authenticated Encryption with Associated Data) algorithms.
AEAD algorithms perform authentication and encryption in one
step. Traditionally users (such as IPsec) would use two
different crypto algorithms to perform these. With AEAD
this comes down to one algorithm and one operation.
Of course if traditional algorithms were used we'd still
be doing two operations underneath. However, real AEAD
algorithms may allow the underlying operations to be
optimised as well.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This function allocates the zeroed chunk of memory and
call seq_open(). The __seq_open_private() helper returns
the allocated memory to make it possible for the caller
to initialize it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct
net_device objects.") changed the interface to NAPI polling. Fix up
the ibm_emac driver so that it works with this new interface. This is
actually a nice cleanup because ibm_emac is one of the drivers that
wants to have multiple NAPI structures for a single net_device.
Tested with the internal MAC of a PowerPC 440SPe SoC with an AMCC
'Yucca' evaluation board.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With the net namespaces many code leaved the __init section,
thus making the kernel occupy more memory than it did before.
Since we have a config option that prohibits the namespace
creation, the functions that initialize/finalize some netns
stuff are simply not needed and can be freed after the boot.
Currently, this is almost not noticeable, since few calls
are no longer in __init, but when the namespaces will be
merged it will be possible to free more code. I propose to
use the __net_init, __net_exit and __net_initdata "attributes"
for functions/variables that are not used if the CONFIG_NET_NS
is not set to save more space in memory.
The exiting functions cannot just reside in the __exit section,
as noticed by David, since the init section will have
references on it and the compilation will fail due to modpost
checks. These references can exist, since the init namespace
never dies and the exit callbacks are never called. So I
introduce the __exit_refok attribute just like it is already
done with the __init_refok.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for 5784 and 5764 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer tg3 devices shuffle around the registers in PCI configuration
space. This patch changes the way the driver accesses the PCI
capabilities registers. Hardcoded register locations are replaced with
offsets from pci_find_capability() return values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This
* removes a declaration of a non-existent function
__dccp_minisock_init;
* shifts the initialisation function dccp_minisock_init() from
options.c to minisocks.c, where it is more naturally expected to
be.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables applications to query the current value of the Maximum
Packet Size via a socket option, suggested as a SHOULD in (RFC 4340,
p. 102).
This socket option is useful to avoid the annoying bail-out via
`-EMSGSIZE'. In particular, as fragmentation is not currently
supported (and its use is partly discouraged in RFC 4340).
With this option, it is possible to size buffers accordingly, e.g.
int buflen = dccp_get_cur_mps(sockfd);
/* or */
if (msgsize > dccp_get_cur_mps(sockfd))
die("message is too large for this path");
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Buttons that work directly on hardware cannot support
the "user_claim" functionality. Add a flag to signal
this and return -EOPNOTSUPP in this case.
b43 is such a device.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a LED trigger.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, bitbanged MDIO was only supported in individual
hardware-specific drivers. This code factors out the higher level
protocol implementation, reducing the hardware-specific portion to
functions setting direction, data, and clock.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The existing OF glue code was crufty and broken. Rather than fix it, it
will be removed, and the ethernet driver now talks to the device tree
directly.
The old, non-CONFIG_PPC_CPM_NEW_BINDING code can go away once CPM
platforms are dropped from arch/ppc (which will hopefully be soon), and
existing arch/powerpc boards that I wasn't able to test on for this
patchset get converted (which should be even sooner).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook up the 93cx6 eeprom code to the ax88796 driver and modify the ax88796
driver to read out the mac address from the eeprom. We need this for the
ax88796 on certain SuperH boards. The pin configuration used to connect
the eeprom to the ax88796 on these boards is the same as pointed out by the
ax88796 datasheet, so we can probably reuse this code for multiple
platforms in the future.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Keep track of disable_irq_nosync() invocations and call enable_irq() the
right number of times if work has been cancelled that would include them.
Now that the call to flush_work_keventd() (problematic because of
rtnl_mutex being held) has been replaced by cancel_work_sync() another
issue has arisen and been left unresolved. As the MDIO bus cannot be
accessed from the interrupt context the PHY interrupt handler uses
disable_irq_nosync() to prevent from looping and schedules some work to be
done as a softirq, which, apart from handling the state change of the
originating PHY, is responsible for reenabling the interrupt. Now if the
interrupt line is shared by another device and a call to the softirq
handler has been cancelled, that call to enable_irq() never happens and the
other device cannot use its interrupt anymore as its stuck disabled.
I decided to use a counter rather than a flag because there may be more
than one call to phy_change() cancelled in the queue -- a real one and a
fake one triggered by free_irq() if DEBUG_SHIRQ is used, if nothing else.
Therefore because of its nesting property enable_irq() has to be called the
right number of times to match the number disable_irq_nosync() was called
and restore the original state. This DEBUG_SHIRQ feature is also the
reason why free_irq() has to be called before cancel_work_sync().
While at it I updated the comment about phy_stop_interrupts() being called
from `keventd' -- this is no longer relevant as the use of
cancel_work_sync() makes such an approach unnecessary. OTOH a similar
comment referring to flush_scheduled_work() in phy_stop() still applies as
using cancel_work_sync() there would be dangerous.
Checked with checkpatch.pl and at the run time (with and without
DEBUG_SHIRQ).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
device_bind_driver() error code returning has been fixed. release()
function has been written, so that to free resources in correct way; the
release path is now clean.
Before the rework, it used to cause
Device 'fixed@100:1' does not have a release() function, it is broken
and must be fixed.
BUG: at drivers/base/core.c:104 device_release()
Call Trace:
[<ffffffff802ec380>] kobject_cleanup+0x53/0x7e
[<ffffffff802ec3ab>] kobject_release+0x0/0x9
[<ffffffff802ecf3f>] kref_put+0x74/0x81
[<ffffffff8035493b>] fixed_mdio_register_device+0x230/0x265
[<ffffffff80564d31>] fixed_init+0x1f/0x35
[<ffffffff802071a4>] init+0x147/0x2fb
[<ffffffff80223b6e>] schedule_tail+0x36/0x92
[<ffffffff8020a678>] child_rip+0xa/0x12
[<ffffffff80311714>] acpi_ds_init_one_object+0x0/0x83
[<ffffffff8020705d>] init+0x0/0x2fb
[<ffffffff8020a66e>] child_rip+0x0/0x12
Also changed the notation of the fixed phy definition on
mdio bus to the form of <speed>+<duplex> to make it able to be used by
gianfar and ucc_geth that define phy_id strictly as "%d:%d" and cleaned up
the whitespace issues.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is ipt_time from POM-ng enhanced by the following:
* xtables/ipv6 support
* second granularity for daytime
* day-of-month support (for example "match on the 15th of each month")
* match against UTC or local timezone
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to relate a connection to an existing master
connection. This patch is used by conntrackd to correctly replicate
related connections.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for automatic checking of per-callback attribute policies.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no struct nfattr anymore, rename functions to 'nlattr'.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the duplicated rtnetlink macros and use the generic netlink
attribute functions. The old duplicated stuff is moved to a new header
file that exists just for userspace.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
rfkill_switch_all shouldn't be called by drivers directly,
instead they should send a signal over the input device.
To prevent confusion for driver developers, move the
function into a rfkill private header.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stateless NAT is useful in controlled environments where restrictions are
placed on through traffic such that we don't need connection tracking to
correctly NAT protocol-specific data.
In particular, this is of interest when the number of flows or the number
of addresses being NATed is large, or if connection tracking information
has to be replicated and where it is not practical to do so.
Previously we had stateless NAT functionality which was integrated into
the IPv4 routing subsystem. This was a great solution as long as the NAT
worked on a subnet to subnet basis such that the number of NAT rules was
relatively small. The reason is that for SNAT the routing based system
had to perform a linear scan through the rules.
If the number of rules is large then major renovations would have take
place in the routing subsystem to make this practical.
For the time being, the least intrusive way of achieving this is to use
the u32 classifier written by Alexey Kuznetsov along with the actions
infrastructure implemented by Jamal Hadi Salim.
The following patch is an attempt at this problem by creating a new nat
action that can be invoked from u32 hash tables which would allow large
number of stateless NAT rules that can be used/updated in constant time.
The actual NAT code is mostly based on the previous stateless NAT code
written by Alexey. In future we might be able to utilise the protocol
NAT code from netfilter to improve support for other protocols.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
These inlines are generally useful, not just with mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap the hard_header_parse function to simplify next step of
header_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add inline for common usage of hardware header creation, and
fix bug in IPV6 mcast where the assumption about negative return is
an errno. Negative return from hard_header means not enough space
was available,(ie -N bytes).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes loopback_dev per network namespace. Adding
code to create a different loopback device for each network
namespace and adding the code to free a loopback device
when a network namespace exits.
This patch modifies all users the loopback_dev so they
access it as init_net.loopback_dev, keeping all of the
code compiling and working. A later pass will be needed to
update the users to use something other than the initial network
namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows you to create a new network namespace
using sys_clone, or sys_unshare.
As the network namespace is still experimental and under development
clone and unshare support is only made available when CONFIG_NET_NS is
selected at compile time.
As this patch introduces network namespace support into code paths
that exist when the CONFIG_NET is not selected there are a few
additions made to net_namespace.h to allow a few more functions
to be used when the networking stack is not compiled in.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a SHOULD from RFC 4340, 7.5.4:
"To protect against denial-of-service attacks, DCCP implementations SHOULD
impose a rate limit on DCCP-Syncs sent in response to sequence-invalid packets,
such as not more than eight DCCP-Syncs per second."
The rate-limit is maintained on a per-socket basis. This is a more stringent
policy than enforcing the rate-limit on a per-source-address basis and
protects against attacks with forged source addresses.
Moreover, the mechanism is deliberately kept simple. In contrast to
xrlim_allow(), bursts of Sync packets in reply to sequence-invalid packets
are not supported. This foils such attacks where the receipt of a Sync
triggers further sequence-invalid packets. (I have tested this mechanism against
xrlim_allow algorithm for Syncs, permitting bursts just increases the problems.)
In order to keep flexibility, the timeout parameter can be set via sysctl; and
the whole mechanism can even be disabled (which is however not recommended).
The algorithm in this patch has been improved with regard to wrapping issues
thanks to a suggestion by Arnaldo.
Commiter note: Rate limited the step 6 DCCP_WARN too, as it says we're
sending a sync.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This adds fields to support the informational Data 1..3 fields of the
DCCP-Reset packets (RFC 4340, 5.6), and makes minor cosmetic changes
to documentation.
Code which fills in these fields follows in subsequent patches, it is
primarily used for reporting option-processing and feature-negotiation
errors.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Am Freitag, 21. September 2007 schrieb Herbert Xu:
> Please don't use LLTX in new drivers. We're trying to get rid
> of it since it's
>
> 1) unnecessary;
> 2) causes problems with AF_PACKET seeing things twice.
I suggest to document that LLTX is deprecated.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all occurences to the static variable
loopback_dev to a pointer loopback_dev. That provides the
mindless, trivial, uninteressting change part for the dynamic
allocation for the loopback.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: Kirill Korotaev <dev@sw.ru>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SSB is an SoC bus used in a number of embedded devices. The most
well-known of these devices is probably the Linksys WRT54G, but there
are others as well. The bus is also used internally on the BCM43xx
and BCM44xx devices from Broadcom.
This patch also includes support for SSB ID tables in modules, so
that SSB drivers can be loaded automatically.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I proposed introducing a list_for_each_entry_continue_reverse macro
to be used in setup_net() when unrolling the failed ->init callback.
Here is the macro and some more cleanup in the setup_net() itself
to remove one variable from the stack :) The same thing is for the
cleanup_net() - the existing list_for_each_entry_reverse() is used.
Minor, but the code looks nicer.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Background: RFC 4293 deprecates existing individual, named ICMP
type counters to be replaced with the ICMPMsgStatsTable. This table
includes entries for both IPv4 and IPv6, and requires counting of all
ICMP types, whether or not the machine implements the type.
These patches "remove" (but not really) the existing counters, and
replace them with the ICMPMsgStats tables for v4 and v6.
It includes the named counters in the /proc places they were, but gets the
values for them from the new tables. It also counts packets generated
from raw socket output (e.g., OutEchoes, MLD queries, RA's from
radvd, etc).
Changes:
1) create icmpmsg_statistics mib
2) create icmpv6msg_statistics mib
3) modify existing counters to use these
4) modify /proc/net/snmp to add "IcmpMsg" with all ICMP types
listed by number for easy SNMP parsing
5) modify /proc/net/snmp printing for "Icmp" to get the named data
from new counters.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Background: RFC 4293 deprecates existing individual, named ICMP
type counters to be replaced with the ICMPMsgStatsTable. This table
includes entries for both IPv4 and IPv6, and requires counting of all
ICMP types, whether or not the machine implements the type.
These patches "remove" (but not really) the existing counters, and
replace them with the ICMPMsgStats tables for v4 and v6.
It includes the named counters in the /proc places they were, but gets the
values for them from the new tables. It also counts packets generated
from raw socket output (e.g., OutEchoes, MLD queries, RA's from
radvd, etc).
Changes:
1) create icmpmsg_statistics mib
2) create icmpv6msg_statistics mib
3) modify existing counters to use these
4) modify /proc/net/snmp to add "IcmpMsg" with all ICMP types
listed by number for easy SNMP parsing
5) modify /proc/net/snmp printing for "Icmp" to get the named data
from new counters.
[new to 2nd revision]
6) support per-interface ICMP stats
7) use common macro for per-device stat macros
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP Supported Extenions parameter is specified in Section 4.2.7
of the ADD-IP draft (soon to be RFC). The parameter is
encoded as:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Parameter Type = 0x8008 | Parameter Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CHUNK TYPE 1 | CHUNK TYPE 2 | CHUNK TYPE 3 | CHUNK TYPE 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| .... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CHUNK TYPE N | PAD | PAD | PAD |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
It contains a list of chunks that a particular SCTP extension
uses. Current extensions supported are Partial Reliability
(FWD-TSN) and ADD-IP (ASCONF and ASCONF-ACK).
When implementing new extensions (AUTH, PKT-DROP, etc..), new
chunks need to be added to this parameter. Parameter processing
would be modified to negotiate support for these new features.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces the void * parameter with a struct net_device * which
is what is actually required.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HARD_TX_LOCK micro is a nice aggregation that could be used
in other spots. move it to netdevice.h
Also makes sure the previously superflous cpu arguement is used.
Thanks to DaveM for the suggestions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have struct net_device_stats embedded in struct net_device,
and the default ->get_stats() hook does the obvious thing for us.
Run through drivers/net/* and remove the driver-local storage of
statistics, and driver-local ->get_stats() hook where applicable.
This was just the low-hanging fruit in drivers/net; plenty more drivers
remain to be updated.
[ Resolved conflicts with napi_struct changes and fix sunqe build
regression... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add support for UWB keys to rfkill,
support for this has been requested by Inaky.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Dmitry pointed out earlier, rfkill-input.c
doesn't support irda because there are no users
and we shouldn't add unrequired KEY_ defines.
However, RFKILL_TYPE_IRDA was defined in the
rfkill.h header file and would confuse people
about whether it is implemented or not.
This patch removes IRDA support completely,
so it can be added whenever a driver wants the
feature.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem: proc_net files remember which network namespace the are
against but do not remember hold a reference count (as that would pin
the network namespace). So we currently have a small window where
the reference count on a network namespace may be incremented when opening
a /proc file when it has already gone to zero.
To fix this introduce maybe_get_net and get_proc_net.
maybe_get_net increments the network namespace reference count only if it is
greater then zero, ensuring we don't increment a reference count after it
has gone to zero.
get_proc_net handles all of the magic to go from a proc inode to the network
namespace instance and call maybe_get_net on it.
PROC_NET the old accessor is removed so that we don't get confused and use
the wrong helper function.
Then I fix up the callers to use get_proc_net and handle the case case
where get_proc_net returns NULL. In that case I return -ENXIO because
effectively the network namespace has already gone away so the files
we are trying to access don't exist anymore.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET=no, init_net is unresolved because net_namespace.c
is not compiled and the include pull init_net definition.
This problem was very similar with the ipc namespace where the kernel
can be compiled with SYSV ipc out.
This patch fix that defining a macro which simply remove init_net
initialization from nsproxy namespace aggregator.
Compiled and booted on qemu-i386 with CONFIG_NET=no and CONFIG_NET=yes.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done in order to, add support to changing the rate table to
use the upper-boundry L2T (length to time) value. Currently we use the
lower-boundry, which result in under-estimating the actual bandwidth
usage.
Extend the tc_ratespec struct, with two parameters: 1) "cell_align"
that allow adjusting the alignment of the rate table. 2) "overhead"
that allow adding a packet overhead before the lookup.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro definition is bad. When calling next_net_device with
parameter name "dev", the resulting code is:
struct net_device *dev = dev and that leads to an unexpected
behavior. Especially when llc_core is compiled in, the kernel panics
at boot time.
The patchset change macro definition with static inline functions as
they were defined before.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows the generic attribute interface to be used within
the netfilter subsystem where this flag was initially introduced.
The byte-order flag is yet unused, it's intended use is to
allow automatic byte order convertions for all atomic types.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The simplest thing to implement is moving network devices between
namespaces. However with the same attribute IFLA_NET_NS_PID we can
easily implement creating devices in the destination network
namespace as well. However that is a little bit trickier so this
patch sticks to what is simple and easy.
A pid is used to identify a process that happens to be a member
of the network namespace we want to move the network device to.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces NETIF_F_NETNS_LOCAL a flag to indicate
a network device is local to a single network namespace and
should never be moved. Useful for pseudo devices that we
need an instance in each network namespace (like the loopback
device) and for any device we find that cannot handle multiple
network namespaces so we may trap them in the initial network
namespace.
This patch introduces the function dev_change_net_namespace
a function used to move a network device from one network
namespace to another. To the network device nothing
special appears to happen, to the components of the network
stack it appears as if the network device was unregistered
in the network namespace it is in, and a new device
was registered in the network namespace the device
was moved to.
This patch sets up a namespace device destructor that
upon the exit of a network namespace moves all of the
movable network devices to the initial network namespace
so they are not lost.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each netlink socket will live in exactly one network namespace,
this includes the controlling kernel sockets.
This patch updates all of the existing netlink protocols
to only support the initial network namespace. Request
by clients in other namespaces will get -ECONREFUSED.
As they would if the kernel did not have the support for
that netlink protocol compiled in.
As each netlink protocol is updated to be multiple network
namespace safe it can register multiple kernel sockets
to acquire a presence in the rest of the network namespaces.
The implementation in af_netlink is a simple filter implementation
at hash table insertion and hash table look up time.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch passes in the namespace a new socket should be created in
and has the socket code do the appropriate reference counting. By
virtue of this all socket create methods are touched. In addition
the socket create methods are modified so that they will fail if
you attempt to create a socket in a non-default network namespace.
Failing if we attempt to create a socket outside of the default
network namespace ensures that as we incrementally make the network stack
network namespace aware we will not export functionality that someone
has not audited and made certain is network namespace safe.
Allowing us to partially enable network namespaces before all of the
exotic protocols are supported.
Any protocol layers I have missed will fail to compile because I now
pass an extra parameter into the socket creation code.
[ Integrated AF_IUCV build fixes from Andrew Morton... -DaveM ]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes /proc/net per network namespace. It modifies the global
variables proc_net and proc_net_stat to be per network namespace.
The proc_net file helpers are modified to take a network namespace argument,
and all of their callers are fixed to pass &init_net for that argument.
This ensures that all of the /proc/net files are only visible and
usable in the initial network namespace until the code behind them
has been updated to be handle multiple network namespaces.
Making /proc/net per namespace is necessary as at least some files
in /proc/net depend upon the set of network devices which is per
network namespace, and even more files in /proc/net have contents
that are relevant to a single network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please note that network devices do not increase the count
count on the network namespace. The are inside the network
namespace and so the network namespace tag is in the nature
of a back pointer and so getting and putting the network namespace
is unnecessary.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the network namespace from which all which all sockets
and anything else under user control ultimately get their network
namespace parameters.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the current ipsec audit layer
by breaking it up into purpose driven audit calls.
So far, the only audit calls made are when add/delete
an SA/policy. It had been discussed to give each
key manager it's own calls to do this, but I found
there to be much redundnacy since they did the exact
same things, except for how they got auid and sid, so I
combined them. The below audit calls can be made by any
key manager. Hopefully, this is ok.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DSACK case, some events are not extraordinary, such as packet
duplication generated DSACK. They can arrive easily below
snd_una when undo_marker is not set (TCP being in CA_Open),
counting such DSACKs amoung SACK discards will likely just
mislead if they occur in some scenario when there are other
problems as well. Similarly, excessively delayed packets could
cause "normal" DSACKs. Therefore, separate counters are
allocated for DSACK events.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
First user will be the DCCP transport networking protocol.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
This patch introduces support for dynamic reconfiguration (adding, removing
and/or modifying parameters of netconsole targets at runtime) using a
userspace interface exported via configfs. Documentation is also updated
accordingly.
Issues and brief design overview:
(1) Kernel-initiated creation / destruction of kernel objects is not
possible with configfs -- the lifetimes of the "config items" is managed
exclusively from userspace. But netconsole must support boot/module
params too, and these are parsed in kernel and hence netpolls must be
setup from the kernel. Joel Becker suggested to separately manage the
lifetimes of the two kinds of netconsole_target objects -- those created
via configfs mkdir(2) from userspace and those specified from the
boot/module option string. This adds complexity and some redundancy here
and also means that boot/module param-created targets are not exposed
through the configfs namespace (and hence cannot be updated / destroyed
dynamically). However, this saves us from locking / refcounting
complexities that would need to be introduced in configfs to support
kernel-initiated item creation / destroy there.
(2) In configfs, item creation takes place in the call chain of the
mkdir(2) syscall in the driver subsystem. If we used an ioctl(2) to
create / destroy objects from userspace, the special userspace program is
able to fill out the structure to be passed into the ioctl and hence
specify attributes such as local interface that are required at the time
we set up the netpoll. For configfs, this information is not available at
the time of mkdir(2). So, we keep all newly-created targets (via
configfs) disabled by default. The user is expected to set various
attributes appropriately (including the local network interface if
required) and then write(2) "1" to the "enabled" attribute. Thus,
netpoll_setup() is then called on the set parameters in the context of
_this_ write(2) on the "enabled" attribute itself. This design enables
the user to reconfigure existing netconsole targets at runtime to be
attached to newly-come-up interfaces that may not have existed when
netconsole was loaded or when the targets were actually created. All this
effectively enables us to get rid of custom ioctls.
(3) Ultra-paranoid configfs attribute show() and store() operations, with
sanity and input range checking, using only safe string primitives, and
compliant with the recommendations in Documentation/filesystems/sysfs.txt.
(4) A new function netpoll_print_options() is created in the netpoll API,
that just prints out the configured parameters for a netpoll structure.
netpoll_parse_options() is modified to use that and it is also exported to
be used from netconsole.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Acked-by: Keiichi Kii <k-keiichi@bx.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This stale info came from the original idea, which proved to be
unnecessarily complex, sacked_out > 0 is easy to do and that when
it's going to be needed anyway (it _can_ be valid also when
sacked_out == 0 but there's not going to be a guarantee about it
for now).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is easily calculable when needed and user are not that many
after all.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition, added a reference about the purpose of the loop.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is guaranteed to be valid only when !tp->sacked_out. In most
cases this seqno is available in the last ACK but there is no
guarantee for that. The new fast recovery loss marking algorithm
needs this as entry point.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides generic Large Receive Offload (LRO) functionality
for IPv4/TCP traffic.
LRO combines received tcp packets to a single larger tcp packet and
passes them then to the network stack in order to increase performance
(throughput). The interface supports two modes: Drivers can either
pass SKBs or fragment lists to the LRO engine.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
