On Skylake hardware, the link_poll isn't clearing the pending interrupt
bit. Adding a new function for SKX that handles clearing of status bit the
right way.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 783dfa6c ("ntb: Adding Skylake Xeon NTB support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
'request_irq()' and 'free_irq()' should have the same 'dev_id'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The offsets for the SZ registers are wrong. Updated.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Sandeep Mann <sandeep@purestorage.com>
Tested-by: Zachary Ross <zacharyx.ross@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Due to incorrect limit and translation register values, NTB link was
going down when the memory window was setup. Made appropriate changes
as per spec.
Fix limit register values for BAR1, which was overlapping
with the BAR23 address.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
AMD NTB support hotplug under B2B mode. NTB will trigger link
up/down interrupt event when doing plug add/remove, this patch
implements the two interrupt event to support B2B hotplug function.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The Skylake Xeon NTB hardware has made some changes to the register name,
offset, and the way doorbells work. Adding driver support for the new
hardware.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The peer_addr member of intel_ntb_dev is not set, therefore when
acquiring ntb_peer_db and ntb_peer_spad we only get the offset rather
than the actual physical address. Adding fix to correct that.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Clean up duplicated expression by replacing it with the equivalent local
variable pdev.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
It will be useful to know the hardware configured BAR size to diagnose
issues with NTB memory windows.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Kernel zero day testing warned about address space confusion. A virtual
iomem address was used where a physical address is expected. The
offending functions implement an optional part of the api, so they are
removed. They can be added later, after testing.
Fixes: a1b3695820
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
If the parameter given to the macro is replaced throughout the macro as
it is evaluated. The intent is that the macro parameter should replace
the only the first parameter to container_of(). However, the way the
macro was written, it would also inadvertantly replace a structure field
name. If a parameter of any other name is given to the macro, it will
fail to compile, if the structure does not contain a field of the same
name. At worst, it will compile, and hide improper access of an
unintended field in the structure.
Change the macro parameter name, so it does not conflict with the
structure field name.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This adds support for AMD's PCI-Express Non-Transparent Bridge
(NTB) device on the Zeppelin platform. The driver connnects to the
standard NTB sub-system interface, with modification to add hooks
for power management in a separate patch. The AMD NTB device has 3
memory windows, 16 doorbell, 16 scratch-pad registers, and supports
up to 16 PCIe lanes running a Gen3 speeds.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The lower bits read from a BAR register will contain property bits
that we do not care about. Clear those so that we can use the BAR
values for limit and xlat registers.
Reported-by: Conrad Meyer <cem@freebsd.org>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
There is no need for the upstream and downstream addresses to be different
for the NTB configs. Go to using a single set of address. It is still
possible to configure them differently using module parameter override
however.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked and Tested-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Check that b2b_mw_idx is in range of the number of memory windows when
initializing the device. The workaround is considered to be in effect
only if the device b2b_idx is exactly UINT_MAX, instead of any index
past the last memory window.
Only print B2B MW workaround information in debugfs if the workaround is
in effect.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Adding PCI Device IDs for B2B (back to back), RP (root port, primary),
and TB (transparent bridge, secondary) devices.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When split BAR is enabled, the driver needs to dump out the split BAR
registers rather than the original 64bit BAR registers.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The unsafe doorbell and scratchpad access should display reason when
WARN is called. Otherwise we get a stack dump without any explanation.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Printouts driver name and version to indicate what is being loaded.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Instead of using the platform code names, use the correct platform names
to identify the respective Intel NTB hardware.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add module parameters for the addresses to be used in B2B topology.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Set errata flags for the specific device IDs to which they apply,
instead of the whole Xeon hardware class.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen. Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Change ntb_hw_intel to use the new NTB hardware abstraction layer.
Split ntb_transport into its own driver. Change it to use the new NTB
hardware abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer. Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
