Remove per site OOM messages because they duplicate
the generic mm subsystem OOM message.
Use kzalloc instead of kmalloc/memset
when next to the OOM message removals.
Reduces object size (allyesconfig ~2%)
$ size -t drivers/net/caif/built-in.o.old net/caif/built-in.o.old
text data bss dec hex filename
32297 700 8224 41221 a105 drivers/net/caif/built-in.o.old
72159 1317 20552 94028 16f4c net/caif/built-in.o.old
104456 2017 28776 135249 21051 (TOTALS)
$ size -t drivers/net/caif/built-in.o.new net/caif/built-in.o.new
text data bss dec hex filename
31975 700 8184 40859 9f9b drivers/net/caif/built-in.o.new
70748 1317 20152 92217 16839 net/caif/built-in.o.new
102723 2017 28336 133076 207d4 (TOTALS)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case SFB queue is full (hard limit reached), there is no point
spending time to compute hash and maximum qlen/p_mark.
We instead just early drop packet.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
structs introduced in tpacket_v3 implementation are prefixed with 'tpacket'
to avoid namespace collision.
Compile tested.
Signed-off-by: Chetan Loke <loke.chetan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add uapsd_queues and max_sp fields to ieee80211_sta.
These fields might be needed by low-level drivers in
order to configure the AP.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new NL80211_ATTR_STA_WME nested attribute that contains
wme params needed by the low-level driver (uapsd_queues and
max_sp).
Add these params to the station_parameters struct as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating as a P2P GO, we receive some P2P action frames where the
BSSID is set to the peer MAC address. Specifically, this occurs for
invitation responses. These are valid action frames and they should be
passed up.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When associating to an AP, the station might miss the first EAP
packet that the AP sends due to a race condition between the association
success procedure and the rx flow in mac80211.
In such cases, the packet might fall in ieee80211_rx_h_check due to
the fact that the relevant rx->sta wasn't allocated yet.
Allocation of the relevant station info struct before actually
sending the association request and setting it with a new
dummy_sta flag solve this problem.
The station will accept only EAP packets from the AP while it
is in the pre-association/dummy state.
This dummy station entry is not seen by normal sta_info_get()
calls, only by sta_info_get_bss_rx().
The driver is not notified for the first insertion of the
dummy station. The driver is notified only after the association
is complete and the dummy flag is removed from the station entry.
That way, all the rest of the code flow should be untouched by
this change.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Divided the sta_info_insert_rcu function to 3 mini-functions:
sta_info_insert_check - the initial checks done when inserting
a new station
sta_info_insert_ibss - the function that handles the station
addition for IBSS interfaces
sta_info_insert_non_ibss - the function that handles the station
addition in other cases
The outer API was not changed.
The refactoring was done for better usage of the different
stages in the station addition in new scenarios added
in the next commit.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since a v1 of the mesh gate series was accidentally applied, this patch
contains the changes in v2.
These are:
- automatically make mesh gate a root node.
- use TU_TO_EXP_TIME macro.
- initialize timer instead of checking for NULL timer function.
- cleanups.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch series 109f6e39..7361c36c back in 2.6.36 added functionality to
allow credentials to work across pid namespaces for packets sent via
UNIX sockets. However, the atomic reference counts on pid and
credentials caused plenty of cache bouncing when there are numerous
threads of the same pid sharing a UNIX socket. This patch mitigates the
problem by eliminating extraneous reference counts on pid and
credentials on both send and receive path of UNIX sockets. I found a 2x
improvement in hackbench's threaded case.
On the receive path in unix_dgram_recvmsg, currently there is an
increment of reference count on pid and credentials in scm_set_cred.
Then there are two decrement of the reference counts. Once in scm_recv
and once when skb_free_datagram call skb->destructor function
unix_destruct_scm. One pair of increment and decrement of ref count on
pid and credentials can be eliminated from the receive path. Until we
destroy the skb, we already set a reference when we created the skb on
the send side.
On the send path, there are two increments of ref count on pid and
credentials, once in scm_send and once in unix_scm_to_skb. Then there
is a decrement of the reference counts in scm_destroy's call to
scm_destroy_cred at the end of unix_dgram_sendmsg functions. One pair
of increment and decrement of the reference counts can be removed so we
only need to increment the ref counts once.
By incorporating these changes, for hackbench running on a 4 socket
NHM-EX machine with 40 cores, the execution of hackbench on
50 groups of 20 threads sped up by factor of 2.
Hackbench command used for testing:
./hackbench 50 thread 2000
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch a HEARTBEAT chunk is bundled into the ASCONF-ACK
for ADD IP ADDRESS, confirming the new destination as quickly as
possible.
Signed-off-by: Michio Honda <micchie@sfc.wide.ad.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes BUG that the ASCONF receiver transmits DATA chunks
to the newly added UNCONFIRMED destination.
Signed-off-by: Michio Honda <micchie@sfc.wide.ad.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements Proportional Rate Reduction (PRR) for TCP.
PRR is an algorithm that determines TCP's sending rate in fast
recovery. PRR avoids excessive window reductions and aims for
the actual congestion window size at the end of recovery to be as
close as possible to the window determined by the congestion control
algorithm. PRR also improves accuracy of the amount of data sent
during loss recovery.
The patch implements the recommended flavor of PRR called PRR-SSRB
(Proportional rate reduction with slow start reduction bound) and
replaces the existing rate halving algorithm. PRR improves upon the
existing Linux fast recovery under a number of conditions including:
1) burst losses where the losses implicitly reduce the amount of
outstanding data (pipe) below the ssthresh value selected by the
congestion control algorithm and,
2) losses near the end of short flows where application runs out of
data to send.
As an example, with the existing rate halving implementation a single
loss event can cause a connection carrying short Web transactions to
go into the slow start mode after the recovery. This is because during
recovery Linux pulls the congestion window down to packets_in_flight+1
on every ACK. A short Web response often runs out of new data to send
and its pipe reduces to zero by the end of recovery when all its packets
are drained from the network. Subsequent HTTP responses using the same
connection will have to slow start to raise cwnd to ssthresh. PRR on
the other hand aims for the cwnd to be as close as possible to ssthresh
by the end of recovery.
A description of PRR and a discussion of its performance can be found at
the following links:
- IETF Draft:
http://tools.ietf.org/html/draft-mathis-tcpm-proportional-rate-reduction-01
- IETF Slides:
http://www.ietf.org/proceedings/80/slides/tcpm-6.pdfhttp://tools.ietf.org/agenda/81/slides/tcpm-2.pdf
- Paper to appear in Internet Measurements Conference (IMC) 2011:
Improving TCP Loss Recovery
Nandita Dukkipati, Matt Mathis, Yuchung Cheng
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Blocks can be configured with non-static frame-size.
2) Read/poll is at a block-level(as opposed to packet-level).
3) Added poll timeout to avoid indefinite user-space wait on idle links.
4) Added user-configurable knobs:
4.1) block::timeout.
4.2) tpkt_hdr::sk_rxhash.
Changes:
C1) tpacket_rcv()
C1.1) packet_current_frame() is replaced by packet_current_rx_frame()
The bulk of the processing is then moved in the following chain:
packet_current_rx_frame()
__packet_lookup_frame_in_block
fill_curr_block()
or
retire_current_block
dispatch_next_block
or
return NULL(queue is plugged/paused)
Signed-off-by: Chetan Loke <loke.chetan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides base support for transmission of IPv6 packets as
well as the formation of IPv6 link-local addresses and statelessly
autoconfigured addresses on top of IEEE 802.15.4 networks.
For more information please look at the RFC4944 "Compression Format
for IPv6 Datagrams in Low Power and Losst Networks (6LoWPAN).
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Skip IPIP header to get proper layer-4 information.
Like GRE tunnels, this only works if rxhash is not already provided by
the device itself (ethtool -K ethX rxhash off), to allow kernel compute
a software rxhash.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can have the NFC core layer allocating the tx head and tail
room for the drivers and avoid 1 or more SKBs copy on write on
the Tx path.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute,
which will advertise this mesh node as being a mesh gate.
NL80211_HWMP_ROOTMODE must be set or this will do nothing.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set Root Announcement Interval for our mesh
interface. Also, RANN interval is now in proper units of TUs.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix allows userspace to mark a meshif as a root node.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In this implementation, a mesh gate is a root node with a certain bit
set in its RANN flags. The mpath to this root node is marked as a path
to a gate, and added to our list of known gates for this if_mesh. Once a
path discovery process fails, we forward the unresolved frames to a
known gate. Thanks to Luis Rodriguez for refactoring and bug fix help.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, mpaths were never flushed since the mpath is not active once
we call this function.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mesh_queue_preq is invoked invoked from both user (work queue) and
softirq (timer) context, so the _bh version of spinlock needs to be
used. Also, the mpath->state_lock should be softirq safe as well.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have an mpath whose timer has not been initialized, don't try to
delete it.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
make hwmp_dbg print the relevant sdata->name by default and improve
formatting. Also add mpath_dbg macro for debugging of mesh path
operations.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now, when vlan tag on untagged in non-accelerated path is stripped from
skb, headers are reset right away. Benefit from that and avoid calling
__netif_receive_skb recursivelly and just use another_round.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make mesh path selection frames Mesh Action category, remove outdated
Mesh Path Selection category and defines, use updated reason codes, add
mesh_action_is_path_sel for readability, and update/correct path
selection IEs.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the mesh peering frames to the format specified in
the recently ratified 802.11s standard. Several changes took place to
make this happen:
- Change RX path to handle new self-protected frames
- Add new Peering management IE
- Remove old Peer Link IE
- Remove old plink_action field in ieee80211_mgmt header
These changes by themselves would either break peering, or work by
coincidence, so squash them all into this patch.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Have the mesh peering frames use the self-protected action and reason codes
specified in 802.11s and defined in ieee80211.h. Remove the local enums.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct ordering of IEs in the mesh beacon while removing unneeded IEs
from mesh peering frames. Set privacy bit in capability info if security
is enabled. Add utility functions to aid in construction
of IEs and reduce code duplication.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As described at [1] some STAs (i.e. Intel 5100 Windows) can end up
correctly BlockAcking incoming frames without delivering them to user
space if a AMPDU subframe got lost and we don't flush the receipients
reorder buffer with a BlockAckReq. This in turn results in stuck
connections.
According to 802.11n-2009 it is not necessary to send a BAR to flush
the recepients RX reorder buffer but we still do that to be polite.
However, assume the following frame exchange:
AP -> STA, AMPDU (failed)
AP -> STA, BAR (failed)
The client in question then ends up in the same situation and won't
deliver frames to userspace anymore since we weren't able to flush
its reorder buffer.
This is not a hypothetical situation but I was able to observe this
exact behavior during a stress test between a rt2800pci AP and a Intel
5100 Windows client.
In order to work around this issue just tear down the BA session as
soon as a BAR failed to be TX'ed.
[1] http://comments.gmane.org/gmane.linux.kernel.wireless.general/66867
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While at it also fix the indention of the other IEEE80211_BAR_CTRL_ defines.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since clients can have several flags on or off, this patches make them
appear in the local/global transtable output so that they can be checked
for debugging purposes.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
If a node has to send a packet issued by a WIFI client to another WIFI client,
the packet is dropped.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When a node receives a unicast packet it checks if the source and the
destination client can communicate or not due to the AP isolation
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Clients connected through a 802.11 device are now marked with the
TT_CLIENT_WIFI flag. This flag is also advertised with the tt
announcement.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Several typos have been corrected and some sentences have been rephrased
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
hash_add() returns 0 on success while returns -1 either on error and on
entry already present. The caller could use such information to select
its behaviour. For this reason it is useful that hash_add() returns -1
in case on error and returns 1 in case of entry already present.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
