This patch adds recovery mechanism for SDIO RX during SKB allocation
failures.
For allocation failures during multiport aggregation, we skip and drop RX
packets.
For single port read case, we will use preallocated card->mpa_rx.buf to
complete cmd53 read.
Now we terminate SDIO operations only upon cmd53 failures.
CC: James Cameron <quozl@laptop.org>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO reset was not happening properly on mwifiex as cancel_work_sync
in mwifiex_sdio_remove used to kill the calling work function itself.
Due to this, the interface was not getting removed and card was not
getting added again. Reset work function has been made independent
of adapter variable and cancel_work_sync has been moved to cleanup
function.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With patch '960d6d08e39 "mwifiex: delay skb allocation for RX
until cmd53 over"' we no more pass skb parameter to MP aggregation setup
helper function. We instead pass length to be aggregated.
This patch fixes an issue where we were passing length parameter of NULL
skb to aggregation routine resulting into crash. We should instead pass
rx_len received from mp_regs.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch moves SKB allocation for RX packets from current
place i.e. after reading MP regs to place where we already
have read data from SDIO bus ie after cmd53.
mp_rx_aggr_setup has been modified accordingly to set
skb_arr to NULL.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch brings in support for SDIO single port rx aggregation
to mwifiex.
Maximum read size support by SDIO cmd53 is 64K.
Based on multi port aggregation which is already part of mwifiex, idea here
is multiple packets received in FW can be aggregated into single buffer.
A separate upload type is defined for such packet aggregated to single port.
Packets from this single buffer are later deaggregated into individual packets.
This way, driver can receive more packets each time through single SDIO cmd53;
thereby reducing no of times MMC bus is accessed.
SDIO SP aggregation support is advertised by FW during load time and driver
would get FW block size in command response of HostCmd_CMD_SDIO_SP_RX_AGGR_CFG.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename this function to reflect its purpose correctly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed Rx aggregated packets are always followed
by a single Rx packet. This patch improves our logic to add
that extra packet in next aggregation.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for DMA alignment of sk_buffs
allocated for RX.
Patch also adds support to modify skb allocation flags.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch changes datatypes for device capability flags to bool.
Patch also aggregates these variables at single place.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some devices do not support extended scan.
This patch adds support to enble ext_scan selectively.
For SD/PCIe interfaces, deefine ext_scan_support as part of
card structure and use it to initialize ext_scan in adapter
during registering device. For USB interfaces, we initialize
ext_scan during register_dev handler.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SD8801 is Marvell's 1x1 802.11bgn offering.
This patch adds Device IDs for SD8801 and also defines card
structure which has definition for register offsets, buffer sizes etc.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver is loaded, it is important to know if FW was already
active or it is freshly downloaded. This patch increases the
priority of these messages.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
200ms is the requirement to allow VDD1.1 and VDD1.8 to
drop to have proper reset.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch saves sdio registers value before firmware dump,
this can be used to find out reason for FW dump.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to dump driver information to a file
when firmware dump happens. This information can be used to
root casue FW crash.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Auto TDLS support is enabled per device. As of now add this
feature only for SD8887.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds SD8887 support to mwifiex.
SD8887 is Marvell's 1x1 11ac solution.
The corresponding firmware image file is located at:
"mrvl/sd8887_uapsta.bin"
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds some more defitions to card specific register structure
and removes static defines for these registers.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SKB lists have their own lock. So this lock is not needed.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds RX work queue support to mwifiex.
Packets received are queued to internal queue which are then
processed by scheduling a work item for RX process.
RX work is enabled only on SMP systems.
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'mp_data_port_mask' and 'mp_end_port' gives correct information
even for the chipsets supporting SDIO new mode (32 ports).
We will get rid of this chip specific handling.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When aggregation port limit is reached, we stop aggregation and
the data is sent to firmware. It is observed that one less packet
than the port limit is aggregated in this case. ex. 15 instead of
16.
The reason is we have redundant port limit checks before current
packet is added to aggregation buffer.
The issue is fixed by removing these checks. We already have
necessary check in precopy current buffer handling.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mmc_rescan will scan for non-removable cards only once, hence the card
will not be rediscovered.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need wall-clock time here, and in most configurations
that care, there are already timestamps in the kernel using
CONFIG_PRINTK_TIME=y.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates mwifiex Copyright to 2014.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware dump feature is added for SDIO based chipsets
which can be used with the help of ethtool commands.
1) Trigger firmware dump operation:
ethtool --set-dump mlan0 0xff
When the operation is completed, udev event will be sent to
trigger external application.
2) Following udev rule can be used to get the data from ethtool:
DRIVER=="mwifiex_sdio", ACTION=="change", RUN+="/sbin/mwifiex_sdio_fw_dump.sh"
mwifiex_sdio_fw_dump.sh: #!/bin/bash
ethtool --set-dump mlan0 0
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ITCM.log
ethtool --set-dump mlan0 1
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/DTCM.log
ethtool --set-dump mlan0 2
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/SQRAM.log
ethtool --set-dump mlan0 3
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/APU.log
ethtool --set-dump mlan0 4
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/CIU.log
ethtool --set-dump mlan0 5
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ICU.log
ethtool --set-dump mlan0 6
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/MAC.log
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we can derive host pointer from adapter, maintaining
a global variable doesn't make sense.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing dedicated card_reset work queue is replaced with the
interface specific workqueue pointer provided by mwifiex module.
Also new work flag is added for card reset task.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During SDIO MP aggregation, we at first acquire current write
port to write data onto and then proceed with using this port
for SDIO write. If error occurs later in mwifiex_write_data_sync
because device is suspended or SDIO write failure, we do not
restore current write port and write bitmap. This results into
leaking one port and hole in SDIO write port bitmap.
Restore current write port and reset bitmap accordingly in
failure cases to avoid this.
Reported-by: James Cameron <quozl@laptop.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'add_remove_card_sem' semaphore already takes care of
synchronization for driver load and unload threads.
Hence there won't be a case when unload thread is waiting on
'wait_for_completion(fw_load)'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently Tx and Rx buffer sizes are 8K and 16K respectively for
all chipsets. We will change them to 32K for SD8897 and 16K for
older chipsets. SD8897 chipset has more SDIO data ports than
older chipsets.
This patch will help to improve throughput numbers.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes we may end up downloading other commands when host
sleep is configured. This patch makes sure that pending
commands are cancelled and we stop queueing further commands
during host sleep.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Deauth is sent to AP when the device is acting as station at
shutdown time. Similarly we should stop AP operation also.
mwifiex_deauthenticate() takes care closing the connection
based on provided interface type.
Add a new function to simplify the code.
Reported-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently default Tx buffer size configured to firmware is 2K
for all chipsets. This patch changes it to 4K for SD/PCIe/USB
8897 chipsets as per firmware requirements.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver is failed to load, card pointer doesn't get
freed. We will free it in cleanup handler which is called
in failure as well as unload path.
Also, update drvdata in init/cleanup handlers instead of
register/unregister handlers.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While receiving a packet on SDIO interface, we allocate skb with
size multiple of SDIO block size. We need to resize this skb
after RX using packet length from RX header.
Cc: <stable@vger.kernel.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes multiple locations where a little endian host is assumed during
ser/des of messages sent to/received from the chip.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both type and pkt_len variables are in host endian and these should be in
Little Endian in the payload.
Signed-off-by: Tomasz Moń <desowin@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some function definitions are moved to appropriate place
to avoid forward declarations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is observed that when wrong firmware is downloaded for
PCIe card, system hangs for 10 seconds. The reason is mdelay()
is used when firmware status is polled.
Replace mdelay with msleep(non-blocking API) to fix the issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During tear down (e.g. mwifiex_sdio_remove during system suspend),
mwifiex left IRQs enabled for a significant period of time when it was
unable to handle them correctly. This caused interrupt storms and
interfered with the bluetooth interface on the same SDIO card.
Solve this by disabling interrupts at the point when they can no longer
be handled correctly, which is at the start of mwifiex_remove_card().
For cleanliness, we now enable interrupts in the mwifiex_add_card() path,
to be symmetrical with the disabling of interrupts. We also couple the
registration of the sdio IRQ handler with the actual enable/disable of
interrupts at the hardware level.
I also removed a write to this register in mwifiex_init_sdio which seemed
pointless and won't cause any ill effects now that we only register
the SDIO IRQ handler when we are ready to accept interrupts.
Includes some corrections from Amitkumar Karwar.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the key differences between SD8897 and older chipsets
are as follows:
a) sdio mpa_rx and mpa_tx ports have been increased from 16 to 32
b) Same is the case with read/write bitmap that one receives from
mpa_reg read
c) aggregation packet count doubled from 8 to 16
d) Most of key reg addresses are changed
e) There is a separate command or control port
f) Now command rx/tx_done have new interrupts
1. 'supports_sdio_new_mode' flag is added to handle (a) and (b).
2. (c) and (d) are taken care of by filling chip specific
information in global structurei (mwifiex_sdio_sd8897).
3. For older chipsets, port 0 was cmd port and port 1->15 were
data port. Therefore we had CTRL_PORT_MASK to differentiate
port type. Now these changes are under 'has_control_mask' flag.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some macros defined for multiport aggregation
calculations. As we may need to add some more code to
accomodate new chipsets, we will change them to inline
functions. Also, use dynamic allocation for Rx buffer array.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As Multiple-Port Aggregation base address value is fixed, we can
have a macro for it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of 'if else' usage by returning in 'if' block.
This improves readability by removing indentations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some u32 variables in sdio.c are used to store/pass u8 values.
Replace them with u8 variables.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register addresses, firmware name and some macros are specific to
a chip. They are stored in a new structure.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
