The v4l2_dv_timings_cap struct is used to do sanity checks when setting and
enumerating DV timings, ensuring that only valid timings as per the HW
capabilities are allowed.
However, many drivers just filled in 0 for the minimum width, height or
pixelclock frequency. This can cause timings with e.g. 0 as width and height
to be accepted, which will in turn lead to a potential division by zero.
Fill in proper values are minimum boundaries. 640x350 was chosen since it is
the smallest resolution in v4l2-dv-timings.h. Same for 13 MHz as the lowest
pixelclock frequency (it's slightly below the minimum of 13.5 MHz in the
v4l2-dv-timings.h header).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CEC IP is very similar between the three HDMI receivers, but
not identical. Add support for all three variants.
Tested with an adv7604 and an adv7612.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When there is no EDID the CEC adapter should be unconfigured as
well. So call cec_phys_addr_invalidate() when this happens.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Initialise the V4L2 fwnode endpoints to zero in all drivers using
v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint
flags as well as the bus type. Setting bus type to zero will continue to
guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CTA-861 standards have been updated to refer to opRGB instead
of AdobeRGB. The official standard is in fact named opRGB, so
switch to that.
The two old defines referring to ADOBERGB in the public API are
put under #ifndef __KERNEL__ and a comment mentions that they are
deprecated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Several CEC functions are actually specific for use with receivers,
i.e. they should be part of the V4L2 subsystem, not CEC.
These functions deal with validating and modifying EDIDs for (HDMI)
receivers, and they do not actually have anything to do with the CEC
subsystem and whether or not CEC is enabled. The problem was that if
the CEC_CORE config option was not set, then these functions would
become stubs, but that's not right: they should always be valid.
So replace the cec_ prefix by v4l2_ and move them to v4l2-dv-timings.c.
Update all drivers that call these accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The use of 'DTV' is very confusing since it normally refers to Digital
TV e.g. DVB etc.
Instead use 'DV' (Digital Video), which nicely corresponds to the
DV Timings API used to configure such receivers and transmitters.
We keep an alias to avoid breaking userspace applications.
Since this alias is only available if __KERNEL__ is *not* defined
(i.e. it is only available for userspace, not kernelspace), any
drivers that use it also have to be converted to the new define.
These drivers are adv7604, adv7842 and tda1997x.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the of_node_put() is unconditional here there is no need to have it
twice.
Signed-off-by: Nicholas Mc Guire <hofrat@opentech.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV7604 has thirteen 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
[Kieran: Re-adapted for mainline]
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the old license information with the corresponding SPDX
license for those drivers Cisco authored.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A 'return' was missing when detecting Arbitration Lost and
calling transmit_done. With the return transmit_done could be
called a second time, confusing the CEC framework. Luckily
the Arbitration Lost condition is very rare.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written !…
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensource.com: fold several similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These can only be accessed with CAP_SYS_ADMIN so it's not a critical
security issue. The problem is that "page" is controlled by the user in
the ioctl(). The test to see if the bit is set in state->info->page_mask
is not sufficient because "page" can be very high and shift wrap around
to a bit which is set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the new CEC_CAP_DEFAULTS define in the adv, vivid, pulse8 and
rainshadow CEC drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch users of the v4l2_of_ APIs to the more generic v4l2_fwnode_ APIs.
Async OF matching is replaced by fwnode matching and OF matching support
is removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Benoit Parrot <bparrot@ti.com> # i2c/ov2569.c, am437x/am437x-vpfe.c and ti-vpe/cal.c
Tested-by: Hans Verkuil <hans.verkuil@cisco.com> # Atmel sama5d3 board + ov2640 sensor
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The adv7604 driver platform data contains fields for configuring the drive
strength of the output pins. When probing the driver through DT these
fields are not explicitly initialized, which means they are left at 0. This
is a reserved setting for the drive strength configuration though and can
cause signal integrity issues.
Whether these signal integrity issues are visible depends on the PCB
specifics (e.g. the higher the load capacitance for the output the more
visible the issue). But it has been observed on existing solutions at high
pixel clock rates.
Initialize the drive strength settings to the power-on-reset value of the
device when probing through devicetree to avoid this issue.
Fixes: 0e158be0162b ("adv7604: Add DT support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cec_allocate_adapter function doesn't need the parent device, only the
cec_register_adapter function needs it.
Drop the cec_devnode parent field, since devnode.dev.parent can be used
instead.
This change makes the framework consistent with other frameworks where the
parent device is not used until the device is registered.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Obtain the correct timings based on the VIC code from the AVI InfoFrame.
It does a sanity check to see if at least the measured width and height
are in line with what the VIC code reports. If not, then use the timings
instead of the VIC code (as per the CEA-861 spec).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Documentation states that the "default-input" property should reside
directly in the node of the device. This adjusts the parsing to make the
implementation consistent with the documentation.
Based on patch by William Towle <william.towle@codethink.co.uk>.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a number of bugs that appeared when support for mediabus formats was
added:
- Support for V4L2_DV_RGB_RANGE_FULL/LIMITED should only be enabled
for HDMI RGB formats, not for YCbCr formats. Since, as the name
says, this setting is for RGB only. So read the InfoFrame to check
the format.
- the quantization range for the pixelport depends on whether the
mediabus code is RGB or not: if it is RGB, then produce full range
RGB values, otherwise produce limited range YCbCr values.
This means that the op_656_range and alt_data_sat fields of the
platform data are no longer used and these will be removed in a
following patch.
- when setting up a new format the RGB quantization range settings
were never updated. Do so, since this depends on the format.
- fix the log_status output which was confusing and incorrect.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The part can be reset by a low pulse on the RESET pin (i.e. a hardware
reset) with a minimum width of 5 ms. It is recommended to wait 5 ms
after the low pulse before an I2C write is performed to the part.
For safety reasons, the delays will be between 5 and 10 ms.
The RESET pin can be tied high, so the GPIO is optional.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_queues" enables hotplugging.
It has a single work item(&state->delayed_work_enable_hotplug) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been sync cancelled in adv76xx_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support to the adv7604 driver.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
[k.debski@samsung.com: Merged changes from CEC Updates commit by Hans Verkuil]
[k.debski@samsung.com: add missing methods cec/io_write_and_or]
[k.debski@samsung.com: change adv7604 to adv76xx in added functions]
[hansverk@cisco.com: use _clr_set instead of _and_or]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dv_timings_cap() and enum_dv_timings() pad operations take a pad
number as an input argument and return the DV timings capabilities and
list of supported DV timings for that pad.
Commit bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings
helpers") broke this as it started ignoring the pad number, always
returning the information associated with the currently selected input.
Fix it.
Fixes: bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings helpers")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Marking these controls as private seemed a good idea at one time,
but in practice it makes no sense. So drop this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to import the changes at media.h, as we have a
followup patch that depends on it.
* v4l_for_linus:
[media] media.h: use hex values for range offsets, move connectors base up.
[media] adv7604: fix tx 5v detect regression
The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This receiver now supports reading the IT content type of the incoming
video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the helper to enumerate and set DV timings instead of a custom code.
This will ease debugging too, as it is consistent with other drivers.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the new match_reduced_fps argument to v4l2_match_dv_timings().
Depending on the situation you may or may not desire to match the
reduced_fps flag. Typically only HDMI transmitters will need to
check for this flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, include/media is messy, as it contains both the V4L2 core
headers and some driver-specific headers on the same place. That makes
harder to identify what core headers should be documented and what
headers belong to I2C drivers that are included only by bridge/main
drivers that would require the functions provided by them.
Let's move those i2c specific files to its own subdirectory.
The files to move were produced via the following script:
mkdir include/media/i2c
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/*/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
for i in include/media/*.h; do n=`basename $i`; (for j in $(git grep -l $n); do dirname $j; done)|sort|uniq|grep -ve '^.$' > list; num=$(wc -l list|cut -d' ' -f1); if [ $num == 1 ]; then if [ "`grep i2c list`" != "" ]; then git mv $i include/media/i2c; fi; fi; done
And the references corrected via this script:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="i2c/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Merged Sakari Ailus patch that moves smiapp.h to include/media/i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using adv7611_read_cable_det() for ADV7612 means that full
support for '.max_port = ADV7604_PAD_HDMI_PORT_B,' isn't available
due to the need for multiple port reads to determine cable detection,
and an agreed mechanism for communicating the separate statuses.
This patch replaces adv7611_read_cable_det() with a functionally
identical copy, commented appropriately.
Earlier submissions [leading to commit 8331d30b] also set .cp_csc,
which is used in a cp_read() call within adv76xx_log_status().
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prior to commit f862f57d ("[media] media: i2c: ADV7604: Migrate to
regmap"), the local variable 'val' contained the combined register
reads used in the chipset version ID test. Restore this expectation
so that the comparison works as it used to.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new v4l2_subdev_notify_event() helper function to deliver the
resolution change event to userspace via the v4l2 subdev event queue as
well as to the bridge driver using the callback notify mechanism.
This allows userspace applications to react to changes in resolution. This
is useful and often necessary for video pipelines where there is no direct
1-to-1 relationship between the subdevice converter and the video capture
device and hence it does not make sense to directly forward the event to
the video capture device node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[hans.verkuil@cisco.com: fix obvious mistake: v4l2_event_subdev_unsubscribe -> v4l2_ctrl_subdev_subscribe_event]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow userspace applications to subscribe to control change events. This
can e.g. be used to monitor the 5V detect control to be notified when a
source is connected or disconnected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adds support to the adv7604 driver for specifying the default input
port in the Device tree. If no value is provided, the driver will be
unable to select an input without help from userspace.
Tested-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the ADV7612 chip as implemented on Renesas' Lager
board to adv7604.c, including lists for formats/colourspace/timing
selection and an IRQ handler.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix merge conflicts due to regmap patch]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a preliminary patch in order to add support for ALSA.
It replaces all current i2c access with regmap.
Signed-off-by: Pablo Anton <pablo.anton@veo-labs.com>
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Added support for reduced blanking version 2 (RB v2) in cvt timings.
Standard specifies a fixed vsync pulse of 8 lines to indicate RB v2
timings. Vertical back porch is fixed at 6 lines and vertical front
porch is remainder of vertical blanking time.
For RB v2, horizontal blanking is fixed at 80 pixels. Horizontal sync
is fixed at 32. All horizontal timing counts (active pixels, front,
back porches) can be specified upto a precision of 1.
RB v2 allows for non standard aspect ratios. In RB v2 vsync does not
indicate aspect ratio. In absence of aspect ratio v4l2_detect_cvt()
cannot calculate image width from image height. Hence extending the
v4l2_detect_cvt() to pass image width in case of RB v2.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Extend detect_cvt/gtf API to indicate the format type (interlaced
or progressive). In case of interlaced, the vertical front and back
porch and vsync values for both (odd,even) fields are considered to
derive image height. Populated vsync, vertical front, back porch
values in bt timing structure for even and odd fields and updated
the flags appropriately.
Also modified the functions calling the detect_cvt/gtf(). As of now
these functions are calling detect_cvt/gtf() with interlaced flag
set to false.
Cc: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Log the alternate gamma state and the HDMI colorspace that the adv
device detected.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
