'ret' is always zero, so this is all dead code.
This should quiet Coverity CID #1226739.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
If no devices were found, we would already have skipped over this code.
Detected by Coverity, CID #744270
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
The PARAM command was long unimplemented and it probably wasn't
noticed because chip probing using only the few bytes returned by the
READID command are good enough in most cases to determine the chip in
use.
Still to notice such a shortcoming earlier in the future would be nice
in case it's something more vital.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The mxc-nand driver never supported the PARAM command to read out the
ONFI parameter page and so always relied on probing my manufacturer and
device id (as provided by the READID command).
This patch implements reading out the first parameter page copy at least
which should be good enough in practise.
This makes the boot log change from
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
nand: Micron NAND 128MiB 1,8V 16-bit
to
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
nand: Micron MT29F1G16ABBDAH4
on my machine.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The mxc-nand controller works pagewise and so usually only sends
commands to the flash chip with column == 0. A request with column != 0
from the upper layer is then fulfilled by indexing appropriately into the
device's RAM buffer.
To be able to access the ONFI marker at offset 0x20 in reply to the
READID command however it's invalid to read 32 bytes starting from
column 0.
So let the function used to send the address cycles send the column
address actually passed instead of 0 and fix all callers to pass 0
instead appropriately. Also add some warnings in case this patch changes
the drivers semantics.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the hardware operates in 16 bit mode it always reads 16 bits even
for operations that only have the lower 8 bits defined. So the upper
bits must be discarded. Do this in the read_byte callback instead of
when reading the NAND id to support reading byte wise more than 5 bytes
and at other occations (like reading the ONFI parameter page).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
At least on i.MX25 (i.e. NFCv2) preset_v2 is called with mtd->writesize
== 0 that is before the connect flash chip is detected. It then
configures for 8 bit ECC mode which needs 26 bytes of OOB per 512 bytes
main section. For flashes with a smaller OOB area issuing a read page
command makes the controller stuck with this config.
Note that this currently doesn't hurt because the first read page
command is issued only after detection is complete and preset is called
once more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
While extending the mxc-nand driver it happend to me a few times that
the device was stuck and this made the machine hang during boot. So
implement a timeout and print a stack trace the first time this happens
to make it debuggable. The return type of the waiting function is also
changed to int to be able to handle the timeout in the caller.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently the driver read NFC command registers to get NFC busy flag.
Actually this flag also can be get by reading HSMC_SR register.
Use the read NFC command registers need mapping a huge memory region.
To save the mapped memory region, we change to check NFC busy flag by
reading HSMC_SR register.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix typo, "Unkown" -> "Unknown"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
s3c2410_nand_probe is not the name of the function.
These prints have little utility, so let's just kill them.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
pxa3xx_flash_ids wasn't initialized to 0, which in certain cases could
end up containing corrupted values in its members. Fix this to avoid
possible issues.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As the devicetree binding doesn't require num_cs to exist or be strictly
positive, and neither does the platform data case, a bug appear when
num_cs is set to 0 and panics the kernel.
The issue is that in alloc_nand_resource(), chip is dereferenced without
having a value assigned when num_cs == 0.
Fix this by returning ENODEV is num_cs == 0.
The panic seen is :
Unable to handle kernel NULL pointer dereference at virtual address 000002b8
pgd = c0004000
[000002b8] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT ARM
Modules linked in:
Hardware name: Marvell PXA3xx (Device Tree Support)
task: c3822aa0 ti: c3826000 task.ti: c3826000
PC is at alloc_nand_resource+0x180/0x4a8
LR is at alloc_nand_resource+0xa0/0x4a8
pc : [<c0275b90>] lr : [<c0275ab0>] psr: 68000013
sp : c3827d90 ip : 00000000 fp : 00000000
r10: c3862200 r9 : 0000005e r8 : 00000000
r7 : c3865610 r6 : c3862210 r5 : c3924210 r4 : c3862200
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 0000397f Table: 80004018 DAC: 00000035
Process swapper (pid: 1, stack limit = 0xc3826198)
Stack: (0xc3827d90 to 0xc3828000)
...zip...
[<c0275b90>] (alloc_nand_resource) from [<c0275ff8>] (pxa3xx_nand_probe+0x140/0x978)
[<c0275ff8>] (pxa3xx_nand_probe) from [<c0258c40>] (platform_drv_probe+0x48/0xa4)
[<c0258c40>] (platform_drv_probe) from [<c0257650>] (driver_probe_device+0x80/0x21c)
[<c0257650>] (driver_probe_device) from [<c0257878>] (__driver_attach+0x8c/0x90)
[<c0257878>] (__driver_attach) from [<c0255ec4>] (bus_for_each_dev+0x58/0x88)
[<c0255ec4>] (bus_for_each_dev) from [<c0256ec8>] (bus_add_driver+0xd8/0x1d4)
[<c0256ec8>] (bus_add_driver) from [<c0257f14>] (driver_register+0x78/0xf4)
[<c0257f14>] (driver_register) from [<c00088a8>] (do_one_initcall+0x80/0x1e4)
[<c00088a8>] (do_one_initcall) from [<c048ed08>] (kernel_init_freeable+0xec/0x1b4)
[<c048ed08>] (kernel_init_freeable) from [<c0377d8c>] (kernel_init+0x8/0xe4)
[<c0377d8c>] (kernel_init) from [<c00095f8>] (ret_from_fork+0x14/0x3c)
Code: e503b234 e5953008 e1530001 caffffd1 (e59002b8)
---[ end trace a5770060c8441895 ]---
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Change the handling of the data stage in the driver : don't pump data in
the top-half interrupt, but rather schedule a thread for non dma cases.
This will enable latencies in the data pumping, especially if delays are
required. Moreover platform shall be more reactive as other interrupts
can be served while pumping data.
No throughput degradation was observed, at least on the zylonite
platform, while a slight degradation was being expected.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The NDDB register holds the data that are needed by the read and write
commands.
However, during a read PIO access, the datasheet specifies that after each 32
bytes read in that register, when BCH is enabled, we have to make sure that the
RDDREQ bit is set in the NDSR register.
This fixes an issue that was seen on the Armada 385, and presumably other mvebu
SoCs, when a read on a newly erased page would end up in the driver reporting a
timeout from the NAND.
Cc: <stable@vger.kernel.org> # v3.14
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Ensures that block2mtd is triggered after the block devices are enumerated
at boot time.
This issue is seen on BCM2835 (Raspberry Pi) systems when mounting JFFS2
block2mtd filesystems, probably because of the delay on enumerating a USB
MMC card reader.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rodrigo Freire <rfreire@redhat.com>
Signed-off-by: Herton Krzesinski <herton@redhat.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
NAND:
* Add new Hisilicon NAND driver for Hip04
* Add default reboot handler, to ensure all outstanding erase transactions
complete in time
* jz4740: convert to use GPIO descriptor API
* Atmel: add support for sama5d4
* Change default bitflip threshold to 75% of correction strength
* Miscellaneous cleanups and bugfixes
SPI NOR:
* Freescale QuadSPI:
- Fix a few probe() and remove() issues
- Add a MAINTAINERS entry for this driver
- Tweak transfer size to increase read performance
- Add suspend/resume support
* Add Micron quad I/O support
* ST FSM SPI: miscellaneous fixes
JFFS2:
* gracefully handle corrupted 'offset' field found on flash
Other:
* bcm47xxpart: add tweaks for a few new devices
* mtdconcat: set return lengths properly for mtd_write_oob()
* map_ram: enable use with mtdoops
* maps: support fallback to ROM/UBI for write-protected NOR flash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+nRk
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150216' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND:
- Add new Hisilicon NAND driver for Hip04
- Add default reboot handler, to ensure all outstanding erase
transactions complete in time
- jz4740: convert to use GPIO descriptor API
- Atmel: add support for sama5d4
- Change default bitflip threshold to 75% of correction strength
- Miscellaneous cleanups and bugfixes
SPI NOR:
- Freescale QuadSPI:
- Fix a few probe() and remove() issues
- Add a MAINTAINERS entry for this driver
- Tweak transfer size to increase read performance
- Add suspend/resume support
- Add Micron quad I/O support
- ST FSM SPI: miscellaneous fixes
JFFS2:
- gracefully handle corrupted 'offset' field found on flash
Other:
- bcm47xxpart: add tweaks for a few new devices
- mtdconcat: set return lengths properly for mtd_write_oob()
- map_ram: enable use with mtdoops
- maps: support fallback to ROM/UBI for write-protected NOR flash"
* tag 'for-linus-20150216' of git://git.infradead.org/linux-mtd: (46 commits)
mtd: hisilicon: && vs & typo
jffs2: fix handling of corrupted summary length
mtd: hisilicon: add device tree binding documentation
mtd: hisilicon: add a new NAND controller driver for hisilicon hip04 Soc
mtd: avoid registering reboot notifier twice
mtd: concat: set the return lengths properly
mtd: kconfig: replace PPC_OF with PPC
mtd: denali: remove unnecessary stubs
mtd: nand: remove redundant local variable
MAINTAINERS: add maintainer entry for FREESCALE QUAD SPI driver
mtd: fsl-quadspi: improve read performance by increase AHB transfer size
mtd: fsl-quadspi: Remove unnecessary 'map_failed' label
mtd: fsl-quadspi: Remove unneeded success/error messages
mtd: fsl-quadspi: Fix the error paths
mtd: nand: omap: drop condition with no effect
mtd: nand: jz4740: Convert to GPIO descriptor API
mtd: nand: Request strength instead of bytes for soft BCH
mtd: nand: default bitflip-reporting threshold to 75% of correction strength
mtd: atmel_nand: introduce a new compatible string for sama5d4 chip
mtd: atmel_nand: return max bitflips in all sectors in pmecc_correction()
...
Pull UBI and UBIFS updates from Richard Weinberger:
- cleanups and bug fixes all over UBI and UBIFS
- block-mq support for UBI Block
- UBI volumes can now be renamed while they are in use
- security.* XATTR support for UBIFS
- a maintainer update
* 'for-linus-v3.20' of git://git.infradead.org/linux-ubifs:
UBI: block: Fix checking for NULL instead of IS_ERR()
UBI: block: Continue creating ubiblocks after an initialization error
UBIFS: return -EINVAL if log head is empty
UBI: Block: Explain usage of blk_rq_map_sg()
UBI: fix soft lockup in ubi_check_volume()
UBI: Fastmap: Care about the protection queue
UBIFS: add a couple of extra asserts
UBI: do propagate positive error codes up
UBI: clean-up printing helpers
UBI: extend UBI layer debug/messaging capabilities - cosmetics
UBIFS: add ubifs_err() to print error reason
UBIFS: Add security.* XATTR support for the UBIFS
UBIFS: Add xattr support for symlinks
UBI: Block: Add blk-mq support
UBI: Add initial support for scatter gather
UBI: rename_volumes: Use UBI_METAONLY
UBI: Implement UBI_METAONLY
Add myself as UBI co-maintainer
The intent was to mask away some bits here, not to test true or false.
Fix: 54f531f6e3 ('mtd: hisilicon: add a new NAND controller driver for hisilicon hip04 Soc')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We recently switched from allocating ->rq using blk_init_queue() to
use blk_mq_init_queue() so we need to update the error handling to
check for IS_ERR() instead of NULL.
Fixes: ff1f48ee3b ('UBI: Block: Add blk-mq support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
If one ubi volume is corrupted but another is not, it should be
possible to initialize that ubiblock from a kernel commandline which
includes both of them. This patch changes the error handling behavior
in initializing ubiblock to ensure that all parameters are attempted
even if one fails. If there is a failure, it is logged on dmesg.
It also makes error messages more descriptive by including the
name of the UBI volume that failed.
Tested: Formatted ubi volume /dev/ubi5_0 in a corrupt way and
dev/ubi3_0 properly and included "ubi.block=5,0 ubi.block=3,0" on
the kernel command line. At boot, I see the following in the console:
[ 21.082420] UBI error: ubiblock_create_from_param: block: can't open volume on ubi5_0, err=-19
[ 21.084268] UBI: ubiblock3_0 created from ubi3:0(rootfs)
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch adds the support for hisilicon 504 NAND controller which is now used
by Hisilicon Soc Hip04.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Calling mtd_device_parse_register with the same mtd_info
(e.g. registering several partitions on a single device)
would add the same reboot notifier twice, causing an
infinte loop in notifier_chain_register during boot up.
Signed-off-by: Niklas Cassel <nks@flawful.org>
[Brian: add FIXME comments]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In concat_read_oob both retlen and oobretlen should be updated.
concat_write_oob previously only (improperly) updated retlen.
Signed-off-by: Niklas Cassel <niklass@axis.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver uses NAND_ECC_HW_SYNDROME mode. The nand_scan_tail()
function would not complain about missing ecc->calculate,
ecc->correct, ecc->hwctl handlers.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Set AHB transfer size to 1K which improved the read performance.
Add ahb_buf_size field in fsl_qspi_devtype_data to denote the size for
different SoC.
Before:
root@imx6qdlsolo:~# dd if=/dev/mtd1 of=/dev/null bs=1M count=16
16+0 records in
16+0 records out
16777216 bytes (17 MB) copied, 0.472183 s, 25.1 MB/s
After:
root@imx6qdlsolo:~# dd if=/dev/mtd1 of=/dev/null bs=1M count=16
16+0 records in
16+0 records out
16777216 bytes (17 MB) copied, 0.369439 s, 29.5 MB/s
Signed-off-by: Allen Xu <b45815@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no need to keep the 'map_failed' label. We can simply return the error
code directly and let the code shorter and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the driver successfully probe we already have messages like:
[ 1.140989] fsl-quadspi 21e4000.qspi: s25fl128s (16384 Kbytes)
[ 1.150902] fsl-quadspi 21e4000.qspi: s25fl128s (16384 Kbytes)
Or in case of error:
[ 1.175920] fsl-quadspi: probe of 21e4000.qspi failed with error -12
, so remove the unneeded success/error messages.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Jumping to 'map_failed' label is not correct at these points, as it misses to
disable the clocks that were previously enabled.
Jump to 'irq_failed' label instead that will correctly disable the clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The if and the else branch code are identical - so the condition has no
effect on the effective code. This patch removes the condition and the
duplicated code and updates the documentation as suggested by
Roger Quadros <rogerq@ti.com>.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the GPIO descriptor API instead of the deprecated legacy GPIO API to
manage the busy GPIO.
The patch updates both the jz4740 nand driver and the only user of the driver
the qi-lb60 board driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Previously, we requested that drivers pass ecc.size and ecc.bytes when
using NAND_ECC_SOFT_BCH. However, a driver is likely to only know the ECC
strength required for its NAND, so each driver would need to perform a
strength-to-bytes calculation.
Avoid duplicating this calculation in each driver by asking drivers to
pass ecc.size and ecc.strength so that the strength-to-bytes calculation
need only be implemented once.
This reverts/generalizes this commit:
mtd: nand: Base BCH ECC bytes on required strength
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The recently added mtd_mmap_capabilities can be used from loadable
modules, in particular romfs, but is not exported, so we get
ERROR: "mtd_mmap_capabilities" [fs/romfs/romfs.ko] undefined!
This adds the missing export.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b4caecd480 ("fs: introduce f_op->mmap_capabilities for nommu mmap support")
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fastmap can miss a PEB if it is in the protection queue
and not jet in the used tree.
Treat every protected PEB as used.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
UBI uses positive function return codes internally, and should not propagate
them up, except in the place this path fixes. Here is the original bug report
from Dan Carpenter:
The problem is really in ubi_eba_read_leb().
drivers/mtd/ubi/eba.c
412 err = ubi_io_read_vid_hdr(ubi, pnum, vid_hdr, 1);
413 if (err && err != UBI_IO_BITFLIPS) {
414 if (err > 0) {
415 /*
416 * The header is either absent or corrupted.
417 * The former case means there is a bug -
418 * switch to read-only mode just in case.
419 * The latter case means a real corruption - we
420 * may try to recover data. FIXME: but this is
421 * not implemented.
422 */
423 if (err == UBI_IO_BAD_HDR_EBADMSG ||
424 err == UBI_IO_BAD_HDR) {
425 ubi_warn("corrupted VID header at PEB %d, LEB %d:%d",
426 pnum, vol_id, lnum);
427 err = -EBADMSG;
428 } else
429 ubi_ro_mode(ubi);
On this path we return UBI_IO_FF and UBI_IO_FF_BITFLIPS and it
eventually gets passed to ERR_PTR(). We probably dereference the bad
pointer and oops. At that point we've gone read only so it was already
a bad situation...
430 }
431 goto out_free;
432 } else if (err == UBI_IO_BITFLIPS)
433 scrub = 1;
434
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Let's prefix UBI messages with 'ubiX' instead of 'UBI-X' - this is more
consistent with the way we name UBI devices.
Also, commit "32608703 UBI: Extend UBI layer debug/messaging capabilities"
added the function name print to 'ubi_msg()' - lets revert this change, since
these messages are supposed to be just informative messages, and not debugging
messages.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Some cosmetic fixes to the patch "UBI: Extend UBI layer debug/messaging
capabilities".
Signed-off-by: Tanya Brokhman <tlinder@codeaurora.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Adds a new set of functions to deal with scatter gather.
ubi_eba_read_leb_sg() will read from a LEB into a scatter gather list.
The new data structure struct ubi_sgl will be used within UBI to
hold the scatter gather list itself and metadata to have a cursor
within the list.
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
By using UBI_METAONLY in rename_volumes() it is now possible to rename
an UBI volume atomically while it is open for writing.
This is useful for firmware upgrades.
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Andrew Murray <amurray@embedded-bits.co.uk>
UBI_METAONLY is a new open mode for UBI volumes, it indicates
that only meta data is being changed.
Meta data in terms of UBI volumes means data which is stored in the
UBI volume table but not on the volume itself.
While it does not interfere with UBI_READONLY and UBI_READWRITE
it is not allowed to use UBI_METAONLY together with UBI_EXCLUSIVE.
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Andrew Murray <amurray@embedded-bits.co.uk>
The MTD API reports -EUCLEAN only if the maximum number of bitflips
found in any ECC block exceeds a certain threshold. This is done to
avoid excessive -EUCLEAN reports to MTD users, which may induce
additional scrubbing of data, even when the ECC algorithm in use is
perfectly capable of handling the bitflips.
This threshold can be controlled by user-space (via sysfs), to allow
users to determine what they are willing to tolerate in their
application. But it still helps to have sane defaults.
In recent discussion [1], it was pointed out that our default threshold
is equal to the correction strength. That means that we won't actually
report any -EUCLEAN (i.e., "bitflips were corrected") errors until there
are almost too many to handle. It was determined that 3/4 of the
correction strength is probably a better default.
[1] http://lists.infradead.org/pipermail/linux-mtd/2015-January/057259.html
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Since "BDI: Provide backing device capability information [try #3]" the
backing_dev_info structure also provides flags for the kind of mmap
operation available in a nommu environment, which is entirely unrelated
to it's original purpose.
Introduce a new nommu-only file operation to provide this information to
the nommu mmap code instead. Splitting this from the backing_dev_info
structure allows to remove lots of backing_dev_info instance that aren't
otherwise needed, and entirely gets rid of the concept of providing a
backing_dev_info for a character device. It also removes the need for
the mtd_inodefs filesystem.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Tejun Heo <tj@kernel.org>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
