On an IP event, current code tries to determine if the netdev belongs
to a L3 card by walking all qeth cards in the system, and then all of
their VLAN devices too. Short-cut the whole thing by identifying a L3
device through its netdev_ops.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract a helper that does the actual work & returns the right NOTIFY_*
responses, and start putting the temporary ipaddr container objects
on the stack rather than kmalloc'ing them. They are small, and this
reduces the confusion of which objects actually get added to qeth's
IP tables.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
init_qdio_queues() resets the Input Queue's overall QDIO state, and
positions the buffer cursor back to 0. So this is the obvious place to
also reset the queue's NAPI context (in contrast to doing it rather
randomly in the middle of the big set_online() path).
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newly-allocated skbs default to PACKET_HOST, and eth_type_trans() is
smart enough to determine any other packet type from the frame's
destination address.
So except for the IQD sniffer case, there is no need to set up
skb->pkt_type manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_alloc_skb() doesn't need to disable IRQs during the allocation,
and thus may save us a few cycles.
Doing so requires a small fix-up in the HiperTransport path, which
currently assumes a fixed NET_SKB_PAD headroom padding. napi_alloc_skb()
adds an additional NET_IP_ALIGN padding, so use the proper helper for
setting up the mac_header offset.
Use this opportunity to convert the non-NAPI path to netdev_alloc_skb(),
which means that skb->dev is now always set-up during allocation and
doesn't need to be assigned manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to pass the *payload* length, not the L2 address length.
For qeth (using eth_header()) this is merely a cosmetic change:
the parameter only matters when building headers for ETH_P_802_2
or ETH_P_802_3, whereas our fake headers are built with
ETH_P_IP / ETH_P_IPV6 / 0.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_SG support is currently limited to OSA (and for L2 even OSD)
devices. Advertise it for some more device types (OSM, L2 OSX, z/VM OSA)
that share the same code paths. For now, keep it switched off by
default on these devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"s390/qeth: fix SETIP command handling" introduced a new helper, apply
it driver-wide.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code ("qeth_l3_ip_from_hash()") matches a queried address object
against objects in the IP table by IP address, Mask/Prefix Length and
MAC address ("qeth_l3_ipaddrs_is_equal()"). But what callers actually
require is either
a) "is this IP address registered" (ie. match by IP address only),
before adding a new address.
b) or "is this address object registered" (ie. match all relevant
attributes), before deleting an address.
Right now
1. the ADD path is too strict in its lookup, and eg. doesn't detect
conflicts between an existing NORMAL address and a new VIPA address
(because the NORMAL address will have mask != 0, while VIPA has
a mask == 0),
2. the DELETE path is not strict enough, and eg. allows del_rxip() to
delete a VIPA address as long as the IP address matches.
Fix all this by adding helpers (_addr_match_ip() and _addr_match_all())
that do the appropriate checking.
Note that the ADD path for NORMAL addresses is special, as qeth keeps
track of how many times such an address is in use (and there is no
immediate way of returning errors to the caller). So when a requested
NORMAL address _fully_ matches an existing one, it's not considered a
conflict and we merely increment the refcount.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit cb816192d9.
The issue this attempted to fix never actually occurs.
l3_add_rxip() checks (via l3_ip_from_hash()) if the requested address
was previously added to the card. If so, it returns -EEXIST and doesn't
call l3_add_ip().
As a result, the "address exists" path in l3_add_ip() is never taken
for rxip addresses, and this patch had no effect.
Fixes: cb816192d9 ("s390/qeth: fix using of ref counter for rxip addresses")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registering an IPv4 address with the HW takes quite a while, so we
temporarily drop the ip_htable lock. Any concurrent add/remove of the
same IP adjusts the IP's use count, and (on remove) is then blocked by
addr->in_progress.
After the register call has completed, we check the use count for
concurrently attempted add/remove calls - and possibly straight-away
deregister the IP again. This happens via l3_delete_ip(), which
1) looks up the queried IP in the htable (getting a reference to the
*same* queried object),
2) deregisters the IP from the HW, and
3) frees the IP object.
The caller in l3_add_ip() then does a second free on the same object.
For this case, skip all the extra checks and lookups in l3_delete_ip()
and just deregister & free the IP object ourselves.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the HW is not reachable, then none of the IPs in qeth's internal
table has been registered with the HW yet. So when deleting such an IP,
there's no need to stage it for deregistration - just drop it from
the table.
This fixes the "add-delete-add" scenario on an offline card, where the
the second "add" merely increments the IP's use count. But as the IP is
still set to DISP_ADDR_DELETE from the previous "delete" step,
l3_recover_ip() won't register it with the HW when the card goes online.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_get_elements_for_range() doesn't know how to handle a 0-length
range (ie. start == end), and returns 1 when it should return 0.
Such ranges occur on TSO skbs, where the L2/L3/L4 headers (and thus all
of the skb's linear data) are skipped when mapping the skb into regular
buffer elements.
This overestimation may cause several performance-related issues:
1. sub-optimal IO buffer selection, where the next buffer gets selected
even though the skb would actually still fit into the current buffer.
2. forced linearization, if the element count for a non-linear skb
exceeds QETH_MAX_BUFFER_ELEMENTS.
Rather than modifying qeth_get_elements_for_range() and adding overhead
to every caller, fix up those callers that are in risk of passing a
0-length range.
Fixes: 2863c61334 ("qeth: refactor calculation of SBALE count")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding & removing IP entries for rxip/vipa/ipato/hsuid, forward any
resulting errors back to the sysfs-level caller.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a common helper for parsing an IP address string, let's use it.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO and IQD paths already need to fix-up the current values, and
OSA will require more flexibility in the future as well. So just let
the caller specify the data length.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate the cast type translation, move the passthru path out of
the RCU-guarded section, and use the appropriate rtable helpers when
determining the next-hop address.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L3 packet descriptor's 'dest_addr' field is used for a different
purpose in RX descriptors. Clean up the hard-coded byte accesses and
try to be more self-documenting.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When
1. an skb has no neighbour, and
2. skb->protocol is not IP[V6],
we select the skb's cast type based on its destination MAC address.
The multicast check is currently restricted to Multicast IP-mapped MACs.
Extend it to also cover non-IP Multicast MACs.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the proper helpers to check for multicast IP addressing, and remove
some ancient Token Ring code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once all of qeth_l3_set_rx_mode()'s single-use helpers are folded back
in, the two implementations actually look quite similar. So improve the
readability by converting both set_rx_mode() routines to a common
format.
This also allows us to walk ip_mc_htable just once, instead of three
times.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be a little more self-documenting, and get rid of OSA_ADDR_LEN.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit "s390/qeth: use ip*_eth_mc_map helpers" removed the last
occurrence of CONFIG_IPV6-dependent code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some wrapper indirection, and stop accessing the skb at
hard-coded offsets.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any modification to the takeover IP-ranges requires that we re-evaluate
which IP addresses are takeover-eligible. Otherwise we might do takeover
for some addresses when we no longer should, or vice-versa.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When takeover is switched off, current code clears the 'TAKEOVER' flag on
all IPs. But the flag is also used for RXIP addresses, and those should
not be affected by the takeover mode.
Fix the behaviour by consistenly applying takover logic to NORMAL
addresses only.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various TCP control block fixes, including one that crashes with
SELinux, from David Ahern and Eric Dumazet.
2) Fix ACK generation in rxrpc, from David Howells.
3) ipvlan doesn't set the mark properly in the ipv4 route lookup key,
from Gao Feng.
4) SIT configuration doesn't take on the frag_off ipv4 field
configuration properly, fix from Hangbin Liu.
5) TSO can fail after device down/up on stmmac, fix from Lars Persson.
6) Various bpftool fixes (mostly in JSON handling) from Quentin Monnet.
7) Various SKB leak fixes in vhost/tun/tap (mostly observed as
performance problems). From Wei Xu.
8) mvpps's TX descriptors were not zero initialized, from Yan Markman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tcp: use IPCB instead of TCP_SKB_CB in inet_exact_dif_match()
tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()
rxrpc: Fix the MAINTAINERS record
rxrpc: Use correct netns source in rxrpc_release_sock()
liquidio: fix incorrect indentation of assignment statement
stmmac: reset last TSO segment size after device open
ipvlan: Add the skb->mark as flow4's member to lookup route
s390/qeth: build max size GSO skbs on L2 devices
s390/qeth: fix GSO throughput regression
s390/qeth: fix thinko in IPv4 multicast address tracking
tap: free skb if flags error
tun: free skb in early errors
vhost: fix skb leak in handle_rx()
bnxt_en: Fix a variable scoping in bnxt_hwrm_do_send_msg()
bnxt_en: fix dst/src fid for vxlan encap/decap actions
bnxt_en: wildcard smac while creating tunnel decap filter
bnxt_en: Need to unconditionally shut down RoCE in bnxt_shutdown
phylink: ensure we take the link down when phylink_stop() is called
sfp: warn about modules requiring address change sequence
sfp: improve RX_LOS handling
...
The current GSO skb size limit was copy&pasted over from the L3 path,
where it is needed due to a TSO limitation.
As L2 devices don't offer TSO support (and thus all GSO skbs are
segmented before they reach the driver), there's no reason to restrict
the stack in how large it may build the GSO skbs.
Fixes: d52aec97e5 ("qeth: enable scatter/gather in layer 2 mode")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using GSO with small MTUs currently results in a substantial throughput
regression - which is caused by how qeth needs to map non-linear skbs
into its IO buffer elements:
compared to a linear skb, each GSO-segmented skb effectively consumes
twice as many buffer elements (ie two instead of one) due to the
additional header-only part. This causes the Output Queue to be
congested with low-utilized IO buffers.
Fix this as follows:
If the MSS is low enough so that a non-SG GSO segmentation produces
order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is
where we anticipate the biggest savings, since an SG-enabled
GSO segmentation produces skbs that always consume at least two
buffer elements.
Larger MSS values continue to get a SG-enabled GSO segmentation, since
1) the relative overhead of the additional header-only buffer element
becomes less noticeable, and
2) the linearization overhead increases.
With the throughput regression fixed, re-enable NETIF_F_SG by default to
reap the significant CPU savings of GSO.
Fixes: 5722963a8e ("qeth: do not turn on SG per default")
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
reworked how secondary addresses are managed for qeth devices.
Instead of dropping & subsequently re-adding all addresses on every
ndo_set_rx_mode() call, qeth now keeps track of the addresses that are
currently registered with the HW.
On a ndo_set_rx_mode(), we thus only need to do (de-)registration
requests for the addresses that have actually changed.
On L3 devices, the lookup for IPv4 Multicast addresses checks the wrong
hashtable - and thus never finds a match. As a result, we first delete
*all* such addresses, and then re-add them again. So each set_rx_mode()
causes a short period where the IPv4 Multicast addresses are not
registered, and the card stops forwarding inbound traffic for them.
Fix this by setting the ->is_multicast flag on the lookup object, thus
enabling qeth_l3_ip_from_hash() to search the correct hashtable and
find a match there.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/s390/net/ files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the allocation of the addr buffer fails, we need to free
our refcount on the inetdevice before returning.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the overly complicated VLAN processing from the L3 RX handler into
its l3_rebuild_skb() helper. No change in functionality.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locking the output queue prior to TX is needed on OSA devices,
to synchronize against a packing flush from the TX completion code
(via qeth_check_outbound_queue()).
But send_packet_fast() is only used for IQDs, which don't do packing.
So remove the locking, and apply some easy cleanups.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a prerequisite for unifying the code to build header elements.
The TSO header has a different size, so we can no longer rely on implicitly
adding the size of a normal qeth_hdr.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TSO we need to skip the skb's qeth/IP/TCP headers when mapping
it into buffer elements. Instead of (mis)using skb_pull(), pass a
corresponding offset to fill_buffer() like we already do for IQDs.
No actual change in the resulting TSO buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO code already calculates the length of its header element,
no need to duplicate this in the low-level code again.
Use this opportunity to make hd_len unsigned, and for TSO match
its calculation to what tso_fill_header() does.
No functional change.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP-address setting and removal are delayed when the device is not yet in
state SOFTSETUP or UP. ref_counter has been implemented only for
ip-address with type normal. In this patch ref_counter logic is also used
for ip-address with type rxip to allow appropriate handling of multiple
postponed rxip add and del calls.
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
change trace-messages:
- from addrxip4 to delrxip4
- from addrxip6 to delrxip6
Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up the inline cruft in s390 net drivers. Many of the inlined
functions had only one caller anyway.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some open-coded parts with their proper API calls.
Also remove two skb_[re]set_mac_header() calls in the L2
xmit paths that are clearly no longer required, since at least
commit 6d1ccff627 ("net: reset mac header in dev_start_xmit()").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_l3_setadapter_parms() queries the device for supported
adapterparms, even though they already have been queried as part of the
device's high-level setup. Remove that extra call.
The only call chain for qeth_l3_setadapter_parms() is
__qeth_l3_set_online()
qeth_core_hardsetup_card()
qeth_query_setadapterparms()
qeth_l3_setadapter_parms()
qeth_query_setadapterparms()
, and we only reach qeth_l3_setadapter_parms() if the first
adapterparms query succeeds. Hence removing the second query results in
no loss of functionality.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After transmitting a skb via send_packet[_fast](), the statistics
code accesses the skb once more to account for transmitted page frags.
This has a (theoretical?) race against the TX completion - if the TX
completion is processed and frees the skb before hard_start_xmit()
gets to the statistics part, we access random memory.
Fix this by caching the # of page frags, before the skb is transmitted.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On L3, the qeth_hdr struct needs to be filled with the next-hop
IP address.
The current code accesses rtable->rt_gateway without checking that
rtable is a valid address. The accidental access to a lowcore area
results in a random next-hop address in the qeth_hdr.
rtable (or more precisely, skb_dst(skb)) can be NULL in rare cases
(for instance together with AF_PACKET sockets).
This patch adds the missing NULL-ptr checks.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Fixes: 87e7597b5a qeth: Move away from using neighbour entries in qeth_l3_fill_header()
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code like the rest of the kernel.
Link: http://lkml.kernel.org/r/3f980cd89084ae09716353aba3171e4b3815e690.1499284835.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to how qeth currently does early L2 setup of OSM and OSN
devices, add support for early setup of L3-only devices.
This adds a qeth_l3_devtype that contains all core and l3-specific
sysfs attributes, so that they can be created in one go while probing.
This just adds the infrastructure, exploitation of the support happens
in a subsequent patch.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HiperSocket devices don't need the full IPv6 initialization, but we
should still query the supported assists for logging purposes.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth doesn't advertise NETIF_F_SG for L3 IQDs. So trust the stack to
not hand us any nonlinear skbs, and remove an always-true condition.
With the fact that data_offset < 0 is no longer possible on IQDs,
apply a small cleanup to subsequent code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Assist was never actually implemented in any hardware, so just
remove the leftovers.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
