While possible (and safe) to use the newly introduced
dsa_port_is_vlan_filtering helper, fabricating a dsa_port pointer is a
bit awkward, so simply retrieve this from the dsa_switch structure.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filtering can be built into the kernel, and also dynamically turned
on/off through the bridge master device. Allow re-configuring the switch
appropriately to account for that by deciding whether VLAN table
(v_table) misses should lead to a drop or forward.
Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Northstar Plus SerDes which is accessed through a
special page of the switch. Since this is something that most people
probably will not want to use, make it a configurable option with a
default on ARCH_BCM_NSP where it is the most useful currently.
The SerDes supports both SGMII and 1000baseX modes for both lanes, and
2500baseX for one of the lanes, and is internally looking like a
seemingly standard MII PHY, except for the few bits that got repurposed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for PHYLINK, things are reasonably straight forward since we
do not yet support SerDes interfaces, that leaves us with just
MLO_AN_PHY and MLO_AN_FIXED to deal with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches expose individual interrupt line(s) for port specific
event(s), allow configuring these interrupts at an appropriate time
during port_enable/disable callbacks where all port specific resources
are known to be set-up and ready for use.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Broadcom Cygnus SoC, the brcm tag needs to be inserted
in between the mac address and the ether type (should use
'DSA_PROTO_TAG_BRCM') for the packets sent to the internal
b53 switch.
Since the Cygnus was added with the BCM58XX device id and the
BCM58XX uses 'DSA_PROTO_TAG_BRCM_PREPEND', the data path is
broken, due to the incorrect brcm tag location.
Add a new b53 device id (BCM583XX) for Cygnus family to fix the
issue. Add the new device id to the BCM58XX family as Cygnus
is similar to the BCM58XX in most other functionalities.
Fixes: 1160603960 ("net: dsa: b53: Support prepended Broadcom tags")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reported-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the BCM5389 switch connected through MDIO.
Signed-off-by: Damien Thébault <damien.thebault@vitec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the b53 driver to return PHY statistics when the CPU port used is
different than 5, 7 or 8, because those are typically PHY-less on most
devices. This is useful for debugging link problems between the switch
and an external host when using a non standard CPU port number (e.g: 4).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we largely assumed that we were interested in ETH_SS_STATS
type of strings for all ethtool operations, this is about to change with
the introduction of additional string sets, e.g: ETH_SS_PHY_STATS.
Update all functions to take an appropriate stringset argument and act
on it when it is different than ETH_SS_STATS for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing the port, we allow different ports to have different
statistics. This is useful since some ports have SERDES interfaces
with their own statistic counters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch VLAN ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from VLAN prepare and add operations.
At the same time, fix the following checkpatch warning:
WARNING: line over 80 characters
#74: FILE: drivers/net/dsa/dsa_loop.c:177:
+ const struct switchdev_obj_port_vlan *vlan)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the much more capable b53_get_tag_protocol() which takes care of
all Broadcom switches specifics to resolve which port can have Broadcom
tags enabled or not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2 and b53 replicate the same operations: clear all VLANs and set
their ports to the default VLAN tag (1 for these devices) so export the
b53 function doing just that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export b53_{enable,disable}_port and use these two functions in
bcm_sf2_port_setup and bcm_sf2_port_disable. The generic functions
cannot be used without wrapping because we need to manage additional
switch integration details (PHY, Broadcom tag etc.).
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2 and b53 do exactly the same thing, so share that piece.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bcm_sf2 EEE-related functions to the b53 driver because this is shared
code amongst Gigabit capable switch, only 5325 and 5365 are too old to support
that.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to enable Broadcom tags/headers is largely switch independent,
and in preparation for enabling it for multiple devices with b53, move
the code we have in bcm_sf2.c to b53_common.c
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of repeating the same pattern: acquire mutex, read/write,
release mutex, define a macro: b53_build_op() which takes the type
(read|write), I/O size, and value (scalar or pointer). This helps with
fixing bugs that could exist (e.g: missing barrier, lock etc.).
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not used anywhere, so remove it.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From all switchdev devices only DSA requires special FDB dump. This is due
to lack of ability for syncing the hardware learned FDBs with the bridge.
Due to this it is removed from switchdev and moved inside DSA.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before removing support for vlan dump from
DSA core. The vlans are synced with the bridge and thus there is no
need for special dump operation support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prepare phase for FDB add is unneeded because most of DSA devices
can have failures during bus transactions (SPI, I2C, etc.), thus, the
prepare phase cannot guarantee success of the commit stage.
The support for learning FDB through notification chain, which will be
introduced in the following patches, will provide the ability to notify
back the bridge about successful offload.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support FDB add/del to be on a notifier chain the slave
API need to be changed to be switchdev independent.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA public header includes switchdev.h, use the provided
switchdev_obj_dump_cb_t typedef for the object dump callback.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress or egress capture towards the capture
port. Future improvements could include leveraging the divider to allow
less frames to be captured, as well as matching specific MAC DA/SA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.
Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.
Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the integrated switch found on BCM7278:
- core_reg_align is set to 1, to force a translation into the target
address space which is 8 bytes aligned
- an alternate SWITCH_REG layout is provided since registers are largely
bit/masks compatible but have different offsets
- conditional for all CORE_STS_OVERRIDE_{IMP,GMII_P} since those got
moved way out of the traditional register space
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for making dsa_switch_ops const, export b53 operations
utilized by other drivers such as bcm_sf2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the two functions recently introduced: u64_to_ether() and
ether_to_u64() instead of our own versions.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 58xx and 7445 chips use the Starfighter2 code, define its MIB layout
and introduce a helper function: is58xx() which checks for both of these
IDs for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a device entry for the Broadcom BCM7445 integrated switch
currently backed by bcm_sf2.c. Since this is the latest generation, it
has 4 ARL entries, 4K VLANs and uses Port 8 for the CPU/IMP port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The b53_io_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the SRAB, core driver and binding document to support the
BCM585xx/586xx/88312 integrated switch (Northstar Plus SoCs family).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuration VLANs on B53 devices by implementing the
port VLAN add/del/dump functions. We currently default to a behavior
which is equivalent to having VLAN filtering turned on, where all VLANs
not programmed into the VLAN port-based vector will be discarded on
ingress.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for HW bridging by tying the ports together in the same port
VLAN mask when they belong to the same bridge, and isolating them to be
alone with the CPU port when they are not.
Propagate STP states from the bridge layer to the switch's HW mapping
when requested.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for FDB add/delete/dump using the ARL read/write logic and
the ARL search logic for faster dumps. The code is made flexible enough
it could support devices with a different register layout like BCM5325
and BCM5365 which have fewer number of entries or pack values into a
single 64 bits register.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.
This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).
Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
