Add the definitions for adding entries to the LE resolve list and
removing entries from the LE resolve list. When the LE resolve list
gets changed via HCI commands make sure that the internal storage of
the resolve list entries gets updated.
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a new quirk HCI_QUIRK_NON_PERSISTENT_SETUP allowing that a quirk that
runs setup() after every open() and not just after the first open().
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This event comes after connection complete event for incoming
connections. Since we now have different random address for
each instance, conn resp address is assigned from this event.
As of now only connection part is handled as we are not
enabling duration or max num of events while starting ext adv.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This basically sets the random address for the adv instance
Random address can be set only if the instance is created which
is done in Set ext adv param.
Random address and rpa expire timer and flags have been added
to adv instance which will be used when the respective
instance is scheduled.
This introduces a hci_get_random_address() which returns the
own address type and random address (rpa or nrpa) based
on the instance flags and hdev flags. New function is required
since own address type should be known before setting adv params
but address can be set only after setting params.
< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
Advertising handle: 0x00
Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch basically replaces legacy adv with extended adv
based on the controller support. Currently there is no
design change. ie only one adv set will be enabled at a time.
This also adds tx_power in instance and store whatever returns
from Set_ext_parameter, use the same in adv data as well.
For instance 0 tx_power is stored in hdev only.
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
Handle: 0x00
Properties: 0x0010
Use legacy advertising PDUs: ADV_NONCONN_IND
Min advertising interval: 1280.000 msec (0x0800)
Max advertising interval: 1280.000 msec (0x0800)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
TX power: 127 dbm (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 1M (0x01)
SID: 0x00
Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
Status: Success (0x00)
TX power (selected): 7 dbm (0x07)
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6
Extended advertising: Enabled (0x01)
Number of sets: 1 (0x01)
Entry 0
Handle: 0x00
Duration: 0 ms (0x00)
Max ext adv events: 0
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch reads the number of advertising sets in the controller
during init and save it in hdev.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
1M is mandatory to be supported by LE controllers and the same
would be set in power on. This patch defines hdev flags for
LE PHYs and set 1M to default.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This implements extended LE craete connection and enhanced
LE conn complete event if the controller supports.
For now it is as good as legacy LE connection and event as
no new features in the extended connection is handled.
< HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26
Filter policy: White list is not used (0x00)
Own address type: Public (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Initiating PHYs: 0x01
Entry 0: LE 1M
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Min connection interval: 50.00 msec (0x0028)
Max connection interval: 70.00 msec (0x0038)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4
LE Extended Create Connection (0x08|0x0043) ncmd 2
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
LE Enhanced Connection Complete (0x0a)
Status: Success (0x00)
Handle: 3585
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Connection interval: 67.50 msec (0x0036)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x00
@ MGMT Event: Device Connected (0x000b) plen 40
LE Address: DB:7E:2E:1D:85:E8 (Static)
Flags: 0x00000000
Data length: 27
Name (complete): Designer Mouse
Appearance: Mouse (0x03c2)
Flags: 0x05
LE Limited Discoverable Mode
BR/EDR Not Supported
16-bit Service UUIDs (complete): 1 entry
Human Interface Device (0x1812)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch enables Extended ADV report event if extended scanning
is supported in the controller and process the same.
The new features are not handled and for now its as good as
legacy ADV report.
> HCI Event: LE Meta Event (0x3e) plen 53
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x0013
Props: 0x0013
Connectable
Scannable
Use legacy advertising PDUs
Data status: Complete
Legacy PDU Type: ADV_IND (0x0013)
Address type: Random (0x01)
Address: DB:7E:2E:1A:85:E8 (Static)
Primary PHY: LE 1M
Secondary PHY: LE 1M
SID: 0x00
TX power: 0 dBm
RSSI: -90 dBm (0xa6)
Periodic advertising invteral: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
Data length: 0x1b
0f 09 44 65 73 69 67 6e 65 72 20 4d 6f 75 73 65 ..Designer Mouse
03 19 c2 03 02 01 05 03 03 12 18 ...........
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Re-use kstrtobool_from_user() instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This function allows to send a HCI command without expecting any
controller event/response in return. This is allowed for vendor-
specific commands only.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the HCI User Channel access is requested, then do not try to
undermine it with vendor diagnostic configuration. The exclusive user
is required to configure its own vendor diagnostic in that case and
can not rely on the host stack support.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the LE Set Default PHY command is supported, the indicate to the
controller that the host has no preferences for transmitter PHY or
receiver PHY selection.
Issuing this command gives the controller a clear indication that other
PHY can be selected if available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If either LE Set Default PHY command or LE Set PHY commands is
supported, then enable the LE PHY Update Complete event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the Channel Selection Algorithm #2 feature is supported, then enable
the new LE Channel Selection Algorithm event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the initial connection interval recommended in Bluetooth
Specification v4.2 (30ms - 50ms).
Signed-off-by: Jonas Holmberg <jonashg@axis.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When closing HCI User Channel, the New Settings event was send out to
inform about changed settings. However such event is wrong since the
exclusive HCI User Channel access is active until the Index Added event
has been sent.
@ USER Close: test
@ MGMT Event: New Settings (0x0006) plen 4
Current settings: 0x00000ad0
Bondable
Secure Simple Pairing
BR/EDR
Low Energy
Secure Connections
= Close Index: 00:14:EF:22:04:12
@ MGMT Event: Index Added (0x0004) plen 0
Calling __mgmt_power_off from hci_dev_do_close requires an extra check
for an active HCI User Channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Bluetooth controllers allow for reading hardware and firmware
related vendor specific infos. If they are available, then they can be
exposed via debugfs now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With all the latest fixes applied, I am still able to reproduce this
(and other) warning(s):
WARNING: CPU: 1 PID: 19684 at ../kernel/workqueue.c:4092 destroy_workqueue+0x70a/0x770()
...
Call Trace:
[<ffffffff819fee81>] ? dump_stack+0xb3/0x112
[<ffffffff8117377e>] ? warn_slowpath_common+0xde/0x140
[<ffffffff811ce68a>] ? destroy_workqueue+0x70a/0x770
[<ffffffff811739ae>] ? warn_slowpath_null+0x2e/0x40
[<ffffffff811ce68a>] ? destroy_workqueue+0x70a/0x770
[<ffffffffa0c944c9>] ? hci_unregister_dev+0x2a9/0x720 [bluetooth]
[<ffffffffa0b301db>] ? vhci_release+0x7b/0xf0 [hci_vhci]
[<ffffffffa0b30160>] ? vhci_flush+0x50/0x50 [hci_vhci]
[<ffffffff8117cd73>] ? do_exit+0x863/0x2b90
This is due to race present in the hci_unregister_dev path.
hdev->power_on work races with hci_dev_do_close. One tries to open,
the other tries to close, leading to warning like the above. (Another
example is a warning in kobject_get or kobject_put depending on who
wins the race.)
Fix this by switching those two racers to ensure hdev->power_on never
triggers while hci_dev_do_close is in progress.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the HCI_AUTO_OFF flag is cleared, the power_off delayed work need
to be cancel or HCI will be powered off even if it's managed.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Recently a managed version of led_trigger_register was introduced.
Using devm_led_trigger_register allows to simplify the LED trigger code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for LED triggers to the Bluetooth subsystem and add kernel
config symbol BT_LEDS for it.
For now one trigger for indicating "HCI is powered up" is supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In commit 44d2713774 ("Bluetooth: Compress the size of struct
hci_ctrl") we squashed down the size of the structure by using a union
with the assumption that all users would use the flag to determine
whether we had a req_complete or a req_complete_skb.
Unfortunately we had a case in hci_req_cmd_complete() where we weren't
looking at the flag. This can result in a situation where we might be
storing a hci_req_complete_skb_t in a hci_req_complete_t variable, or
vice versa.
During some testing I found at least one case where the function
hci_req_sync_complete() was called improperly because the kernel thought
that it didn't require an SKB. Looking through the stack in kgdb I
found that it was called by hci_event_packet() and that
hci_event_packet() had both of its locals "req_complete" and
"req_complete_skb" pointing to the same place: both to
hci_req_sync_complete().
Let's make sure we always check the flag.
For more details on debugging done, see <http://crbug.com/588288>.
Fixes: 44d2713774 ("Bluetooth: Compress the size of struct hci_ctrl")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use list_for_each_entry*() instead of list_for_each*() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We can simplify a lot of code by making sure hdev->cur_adv_instance is
always up-to-date. This allows e.g. the removal of the
get_current_adv_instance() helper function and the special
HCI_ADV_CURRENT value. This patch also makes selecting instance 0x00
explicit in the various calls where advertising instances aren't
enabled, e.g. when HCI_ADVERTISING is set or we've just finished
enabling LE.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The request to update HCI during power on is always coming either from
hdev->req_workqueue or through an ioctl, so it's safe to use
hci_req_sync for it. This way we also eliminate potential races with
incoming mgmt commands or other actions while powering on.
Part of this refactoring is the splitting of mgmt_powered() into
mgmt_power_on() and __mgmt_power_off() functions. The main reason is
the different requirements as far as hdev locking is concerned, as
highlighted with the __ prefix of the power off API.
Since the power on in the case of clearing the AUTO_OFF flag cannot be
done synchronously in the set_powered mgmt handler, the hci_power_on
work callback is extended to cover this (which also simplifies the
set_powered helper a lot).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the other discoverable changes are behind req_workqueue now it
only makes sense to move the discoverable timeout there as well.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This paves the way for eventually performing advertising changes
through the hdev->req_workqueue. Some new APIs need to be exposed from
mgmt.c to hci_request.c and vice-versa, but many of them will go away
once hdev->req_workqueue gets used.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix errors reported by checkpatch.
- ERROR: spaces required around that ':' (ctx:VxW)
- ERROR: open brace '{' following function declarations go on the next line
Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_req_sync_cancel() is just as much related to the request
cleanup as hci_request_cancel_all() is. Just move the former into the
latter and do the cleanup from a single place in hci_dev_do_close().
The important thing is to avoid deadlocks by holding the req_sync
lock: previously hci_request_cancel_all was done right after releasing
the lock and with this patch it's right before taking it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances it may be useful to abort the request through
checks done in the request callback. To make the feature possible this
patch changes the return value of the request callback from void to
int and aborts the request if a non-zero value is returned.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To avoid any risks of races, place also these LE scan modification
work callbacks behind the same work queue as the other LE scan
changes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some cases it may be important to get the exact HCI status rather
than the converted HCI-to-errno value. Add an optional return
parameter to the hci_req_sync() API to allow for this. Since there are
no good HCI translation candidates for cancelation and timeout, use
the "unknown" status code for those cases.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Prepare hci_request.c to have code for doing synchronous HCI requests,
such as LE scanning or advertising changes. The necessary work
callbacks will be set up in hci_request_setup() and cleaned up in
hci_request_cancel_all(). The former is used when an HCI device get
registered, and the latter each time it is powered off (or
unregistered).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make it clear which HCI request APIs target specifically
synchronous requests, add 'sync' to the API names.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_request.c is a more natural place for the synchronous request
handling. Furthermore, we will soon need access to some of the
previously private-to-hci_core.c functions from hci_request.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_conn_params_clear_all() function is only called from
hci_unregister_dev() at which point it's completely futile to try to
do any LE scanning updates. Simply remove this unnecessary function
call. At the same time we can make the function static since it's only
accessed from within the same c-file.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We can reduce the size of the hci_ctrl struct by converting
'bool req_start' to 'u8 req_flags' and making the two function
pointers a union (since only one is ever set at a time).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new hci_skb_pkt_* wrappers only help if they are used consistently
in the Bluetooth subsystem. So first convert the core packet handling.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the LE only controllers, there are events that should not be enabled
if the corresponding command is not supported.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
