This allows you to force specific power levels within a power
state. Due to hardware restrictions between generations, the
interface is limited to the following 3 selections:
auto: all levels enabled
low: forced to the lowest power level
high: forced to the highest power level
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
r1xx asics have a slightly different surface register
setup compared to newer asics. There is no specific
enable bit for macro tiling, rather, to disable macro
tiling, you need to set the surface pitch to 0.
With this fixed, the special rn50 handling can go.
Noticed-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Certain older rv770 asics have both a performance and
a 3D performance state rather than just multiple performance
levels in the state power state. The current code would
select the performance state rather than the 3D performance
state when the "performance" profile was selected. This change
switches to the "balanced" profile by default which ends up being
the internal performance profile. When the user selects the
"performance" profile, it selects the internal 3D performance
state so the user can select the higher performance modes.
For most asics this changes nothing. For certain rv770 asics
with static performance and 3D performance states, this allows
you to select between then using by selecting the "balanced"
and "performance" dpm profiles.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix patching of vddc values for SI and enable manually forcing
clocks to default levels as per NI.
This improves the out of the box performance with SI asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UBI device numbers when attaching MTD devices by using the "mtd="
module parameter.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=N5BA
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.11-rc1' of git://git.infradead.org/linux-ubi
Pull ubi fixes from Artem Bityutskiy:
"A couple of fixes and clean-ups, allow for assigning user-defined UBI
device numbers when attaching MTD devices by using the "mtd=" module
parameter"
* tag 'upstream-3.11-rc1' of git://git.infradead.org/linux-ubi:
UBI: support ubi_num on mtd.ubi command line
UBI: fastmap break out of used PEB search
UBI: document UBI_IOCVOLUP better in user header
UBI: do not abort init when ubi.mtd devices cannot be found
UBI: drop redundant "UBI error" string
Add SDHCI driver for the Broadcom 281xx SoCs.
Still missing:
- power managemement
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a card_event callback to sdhci so that clients can provide their
own card_event to be called when card_detect is triggered.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit "mmc: core: Handle card shutdown from mmc_bus" introduced an
Oops in the shutdown sequence for SDIO.
The drv pointer, does not exist for SDIO since the probing of the SDIO
card from the mmc_bus perspective is expected to fail by returning
-ENODEV.
This patch adds the proper check for the pointer before calling it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reported-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add another PCI device id for an eMMC host controller.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The P2020 has a non-standard implementation of the SDHCI_HOST_CONTROL
register. This patch adds a QUIRK in the SDHCI header to signal that
a host controller has a non-standard SDHCI_HOST_CONTROL register. The
patch adds a check to the function esdhc_writeb in file
sdhci-of-esdhc.c, where it checks if the write is done to the
SDHCI_HOST_CONTROL register and th host has the above mentioned QUIRK,
then the function simply returns instead of writing to the register.
The patch also detects if the processor is P2020 (by looking in dev
tree) and if so, adds the QUIRK to the host->quirk2
Signed-off-by: Oded Gabbay <ogabbay@advaoptical.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support of connecting an MMC media using an 8-bit
bus width connection to Freescale's P2020 H/W SDHC controller. During
the probe function, the generic function mmc_of_parse is called to
detect whether the controller is configured with 8-bit bus width.
Also, the generic function detects if the non-removable property is
set in the device tree. The function esdhc_pltfm_bus_width was added
because the bus width configuration is platform specific.
Signed-off-by: Oded Gabbay <ogabbay@advaoptical.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The field containing the production date in the CID register only uses
4 bits to encode the year, starting from 1997 in the original standard.
In 2013, the production year field contains 0, and the kernel reports a
1997 production date.
The eMMC 4.51 specification adds a new interpretation rule. For all
devices implementing the 4.41 specification or later, the production
year field will be interpreted as a value between 2010 and 2025, with
0 corresponding to 2013.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In commit 3451c067 (mmc: omap: add DMA engine support), some #if 0's
were used to comment out parts of the code. This has been in the code
for over a year and are not needed anymore (and the commented-out code
doesn't even compile). Remove them.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes the HC ctrl_2 programming where, in case of
SDR104 and HS200, we have to write 100b in the the UHS Mode
bits. We wrote 101b that is reserved from Arasan Specs.
Reported-by: Youssef Triki <youssef.triki@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cortex-A9 SoCs from Rockchip use a slightly modified variant of dw_mmc
controllers that seems to require the SDMMC_CMD_USE_HOLD_REG bit to
always be set.
There also seem to be no other modifications (additional register etc)
present, so to keep the footprint low, add this small variant to the
pltfm driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In a subsquent patch probe will need to do some handling of data from
the dt match table. So to prevent the need for forward declarations,
move probe and remove below the match table.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
dw_mci_pltfm_remove gets exported and used by dw_mmc-exynos, so should
not be static.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add support for eMMC hardware reset for HID 80860F14.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
smp_call_function_* must not be called from softirq context.
But clock_was_set() which calls on_each_cpu() is called from softirq
context to implement a delayed clock_was_set() for the timer interrupt
handler. Though that almost never gets invoked. A recent change in the
resume code uses the softirq based delayed clock_was_set to support
Xens resume mechanism.
linux-next contains a new warning which warns if smp_call_function_*
is called from softirq context which gets triggered by that Xen
change.
Fix this by moving the delayed clock_was_set() call to a work context.
Reported-and-tested-by: Artem Savkov <artem.savkov@gmail.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>,
Cc: Konrad Wilk <konrad.wilk@oracle.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: xen-devel@lists.xen.org
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Up to commit 5d33b883a (clocksource: Always verify highres capability)
we had no sanity check when selecting a clocksource, which prevented
that a non highres capable clocksource is used when the system already
switched to highres/nohz mode.
The new sanity check works as Alex and Tim found out. It prevents the
TSC from being used. This happens because on x86 the boot process
looks like this:
tsc_start_freqency_validation(TSC);
clocksource_register(HPET);
clocksource_done_booting();
clocksource_select()
Selects HPET which is valid for high-res
switch_to_highres();
clocksource_register(TSC);
TSC is not selected, because it is not yet
flagged as VALID_HIGH_RES
clocksource_watchdog()
Validates TSC for highres, but that does not make TSC
the current clocksource.
Before the sanity check was added, we installed TSC unvalidated which
worked most of the time. If the TSC was really detected as unstable,
then the unstable logic removed it and installed HPET again.
The sanity check is correct and needed. So the watchdog needs to kick
a reselection of the clocksource, when it qualifies TSC as a valid
high res clocksource.
To solve this, we mark the clocksource which got the flag
CLOCK_SOURCE_VALID_FOR_HRES set by the watchdog with an new flag
CLOCK_SOURCE_RESELECT and trigger the watchdog thread. The watchdog
thread evaluates the flag and invokes clocksource_select() when set.
To avoid that the clocksource_done_booting() code, which is about to
install the first real clocksource anyway, needs to go through
clocksource_select and tick_oneshot_notify() pointlessly, split out
the clocksource_watchdog_kthread() list walk code and invoke the
select/notify only when called from clocksource_watchdog_kthread().
So clocksource_done_booting() can utilize the same splitout code
without the select/notify invocation and the clocksource_mutex
unlock/relock dance.
Reported-and-tested-by: Alex Shi <alex.shi@intel.com>
Cc: Hans Peter Anvin <hpa@linux.intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Andi Kleen <andi.kleen@intel.com>
Tested-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1307042239150.11637@ionos.tec.linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 2768935a46 ('sfc: reuse pages to avoid DMA mapping/unmapping
costs') did not fully take account of DMA scattering which was
introduced immediately before. If a received packet is invalid and
must be discarded, we only drop a reference to the first buffer's
page, but we need to drop a reference for each buffer the packet
used.
I think this bug was missed partly because efx_recycle_rx_buffers()
was not renamed and so no longer does what its name says. It does not
change the state of buffers, but only prepares the underlying pages
for recycling. Rename it accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a serious bug in:
14c63f17b1 perf: Drop sample rate when sampling is too slow
There was an misunderstanding on the API of the do_div()
macro. It returns the remainder of the division and this
was not what the function expected leading to disabling the
interrupt latency watchdog.
This patch also remove a duplicate assignment in
perf_sample_event_took().
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Cc: dave.hansen@linux.intel.com
Cc: ak@linux.intel.com
Cc: jolsa@redhat.com
Link: http://lkml.kernel.org/r/20130704223010.GA30625@quad
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As Linus said its not an error to not have an AMD IOMMU; esp.
when you're not even running on an AMD platform.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Link: http://lkml.kernel.org/r/20130703075542.GF23916@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds Device Tree support to the shdma driver. No special DT
properties are used, only standard DMA DT bindings are implemented. Since
shdma controllers reside on SoCs, their configuration is SoC-specific and
shall be passed to the driver from the SoC platform data, using the
auxdata procedure.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
shdma_chan_filter() is a function, provided by the shdma-base.c module,
move its declaration to the appropriate header.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use an existing pointer instead of retrieving it again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: remove return code checking in at_dma_resume_noirq()]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Correct coding style following the patch:
7c407d3e54dcc0c79119553c8d5ef176c1d5bc3a (DMA: AT91:
Get residual bytes in dma buffer).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Since patch 7c407d3e54dcc0c79119553c8d5ef176c1d5bc3a (DMA: AT91:
Get residual bytes in dma buffer), the function
atc_cleanup_descriptors() is not used anymore. We remove it to prevent
warnings.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
For most devices the FIFO configuration is the same i.e. when half FIFO size is
available/filled, a source/destination request is serviced. But USART devices
have to do it when there is enough space/data available to perform a single
AHB access so the ASAP configuration.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
DMA-cell content is a concatenation of several values. In order to keep this
stuff human readable, macros are introduced.
The values for the FIFO configuration are not the same as the ones used in the
configuration register in order to keep backward compatibility. Most devices
use the half FIFO configuration but USART ones have to use the ASAP
configuration. This parameter was not initially planed to be into the at91 dma
dt binding. The third cell will be used to store this parameter, it will
become a concatenation of the FIFO configuration and of the peripheral ID. In
order to keep backward compatibility i.e. FIFO configuration is equal to 0, we
have to perform a translation since the value to put in the register to set
half FIFO is 1.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that all users of the custom jz4740 DMA API have been converted to use
the dmaengine API instead we can remove the custom API and move all the code
talking to the hardware to the dmaengine driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds dmaengine support for the JZ4740 DMA controller. For now the
driver will be a wrapper around the custom JZ4740 DMA API. Once all users of the
custom JZ4740 DMA API have been converted to the dmaengine API the custom API
will be removed and direct hardware access will be added to the dmaengine
driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Previously, it was assumed that the DMA controller clock is not gated
when the kernel starts running. While that is the power-on state, it is
safer to not rely on that.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
mask dma irq when disabling dma channel, so that interrupt status
will not be set and interrupt won't come again.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As pointed out by Arnd Bergmann there is a get_signal macro definied in
linux/signal.h which can conflict with the platform data callback
function of the same name leading to confusing errors from the compiler
(especially if signal.h manages to get pulled into the driver itself due
to header dependencies). Avoid such errors by renaming get_signal and
put_signal in the platform data to get_xfer_signal and put_xfer_signal.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is the PCI part of the DesignWare DMAC driver. The controller is usually
used in the Intel hardware such as Intel Medfield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
