GTT caching was disabled by default on gen8 due to not working with
big pages. Some information suggests that it got fixed, but still
GTT caching has been left disabled by default. Or could be it just
meant that the default was changed to off, and hence the problem
got solved.
Enable GTT caching in the hopes of some performance increase.
Whether or not the big pages issue has been fixed is irrelevant
at this stage since we don't use big pages.
This gives me a 1-2% improvement in xonotic on my BSW. Haven't tried
BDW, but supposedly it has larger TLBs so might not benefit as much.
On HSW GTT caching is enabled by default.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8_L3SQCREG1 isn't saved in the context (verified by going through
a context dump), and so we shouldn't be using the ring w/a code to
initialize it. Also Bspec explicitly talks about MMIO and writing it
with the CPU.
Additionally there's another w/a WaTempDisableDOPClkGating:bdw which
tells us to disable DOP clock gating around the GEN8_L3SQCREG1 write
to make sure everyone notices the change. So let's do that as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're not using ilk_init_lp_watermarks() on BDW for some reason.
Probably due to the BDW patches and the relevant WM patches landing
roughlly at the same time. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec says we should disable the FDI RX/TX before disabling the PCH
ports. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the BSpec sequence for the CRT port as well on PCH platforms,
ie. disable the pipe before the port.
Didn't bother looking at DDI in detail yet, so leave that one be even
though the CRT is a PCH port there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While at it also remove the redundant/unneeded w/a like done for hdmi
already.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Mention that this also removes the unneeded w/a, as suggested
by Jesse.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec says we should disable all ports after the pipe on PCH
platforms. Do so. Fixes a pipe off timeout on ILK now caused by
the transcoder B workaround.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the IBX transcoder B workarounds are not working correctly.
Well, the HDMI one seems to be working somewhat, but the DP one is
definitely busted.
After a bit of experimentation it looks like the best way to make this
work is first disable the port on transcoder B, and then re-enable it
transcoder A, and immediately disable it again.
We can also clean up the code by noting that we can't be called without
a valid crtc. And also note that port A on ILK does not need the
workaround, so let's check for that one too.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On IBX the SDVO/HDMI register write may be masked when enabling the
port, so it may need to written twice. The HDMI code does this, but
the SDVO code does not. Add the workaround to the SDVO code as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we're always enabling enhanced framing on CPT even if the sink
doesn't support it. Fix this up by actaully looking at what the sink
tells us.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Define a TRANS_DP_PIPE_TO_PORT() to make the CPT DP .get_hw_state()
pipe readout neater.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_dp.c is a mess with all the checks for different
platform/PCH variants and ports. Try to clean it up by recognizing
the following facts:
- IVB port A, and CPT port B/C/D are always the special cases
- VLV/CHV don't have port A
- Using the same kind of logic everywhere makes things much easier to
parse
So let's move the IVB port A and PCH port B/C/D checks to be done first,
and let the other cases fall through, and always check for these things
using the same logic.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IBX can have problems with the first write to the port register getting
masked when enabling the port. We are trying to apply the workaround
also when disabling the port where it's not needed, and we also try
to apply it for CPT/PPT as well which don't need it. Just kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with the remove CHV if block.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The IBX 12bpc port enable toggle is only relevant when enabling
the port, not when disabling it. Also this code doesn't actually
toggle anything, and essentially just writes the port register
one extra time. Furthermore CPT/PPT don't need such workarounds
and yet we include them. Just kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init the display hardware when going out of suspend. This
includes:
- Hooking the PCH to the reset logic
- Restoring CDCDLK
- Enabling the DDB power
Among those, only the CDCDLK one is a bit tricky. There's some
complexity in that:
- DPLL0 (which is the source for CDCLK) has two VCOs, each with a set
of supported frequencies. As eDP also uses DPLL0 for its link rate,
once DPLL0 is on, we restrict the possible eDP link rates the chosen
VCO.
- CDCLK also limits the bandwidth available to push pixels.
So, as a first step, this commit restore what the BIOS set, until I can
do more testing.
In case that's of interest for the reviewer, I've unit tested the
function that derives the decimal frequency field:
#include <stdio.h>
#include <stdint.h>
#include <assert.h>
#define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x)))
static const struct dpll_freq {
unsigned int freq;
unsigned int decimal;
} freqs[] = {
{ .freq = 308570, .decimal = 0b01001100111},
{ .freq = 337500, .decimal = 0b01010100001},
{ .freq = 432000, .decimal = 0b01101011110},
{ .freq = 450000, .decimal = 0b01110000010},
{ .freq = 540000, .decimal = 0b10000110110},
{ .freq = 617140, .decimal = 0b10011010000},
{ .freq = 675000, .decimal = 0b10101000100},
};
static void intbits(unsigned int v)
{
int i;
for(i = 10; i >= 0; i--)
putchar('0' + ((v >> i) & 1));
}
static unsigned int freq_decimal(unsigned int freq /* in kHz */)
{
return (freq - 1000) / 500;
}
static void test_freq(const struct dpll_freq *entry)
{
unsigned int decimal = freq_decimal(entry->freq);
printf("freq: %d, expected: ", entry->freq);
intbits(entry->decimal);
printf(", got: ");
intbits(decimal);
putchar('\n');
assert(decimal == entry->decimal);
}
int main(int argc, char **argv)
{
int i;
for (i = 0; i < ARRAY_SIZE(freqs); i++)
test_freq(&freqs[i]);
return 0;
}
v2:
- Rebase on top of -nightly
- Use (freq - 1000) / 500 for the decimal frequency (Ville)
- Fix setting the enable bit of HSW_NDE_RSTWRN_OPT (Ville)
- Rename skl_display_{resume,suspend} to skl_{init,uninit}_cdclk to
be consistent with the BXT code (Ville)
- Store boot CDCLK in ddi_pll_init (Ville)
- Merge dev_priv's skl_boot_cdclk into cdclk_freq
- Use LCPLL_PLL_LOCK instead of (1 << 30) (Ville)
- Replace various '0' by SKL_DPLL0 to be a bit more explicit that
we're programming DPLL0
- Busy poll the PCU before doing the frequency change. It takes about
3/4 cycles, each separated by 10us, to get the ACK from the CPU
(Ville)
v3:
- Restore dev_priv->skl_boot_cdclk, leaving unification with
dev_priv->cdclk_freq for a later patch (Daniel, Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the client stalls on a congested request, chosen to be 20ms old to
match throttling, allow the client a free RPS boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
[danvet: s/0/NULL/ reported by 0-day build]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we have clients stalled waiting for requests, ignore the GPU if it
signals that it should downclock due to low load. This helps prevent
the automatic timeout from causing extremely long running batches from
taking even longer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have internal clients, rather than faking a whole
drm_i915_file_private just for tracking RPS boosts, create a new struct
intel_rps_client and pass it along when waiting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we will often pageflip to an active surface, we will often have to
wait for the surface to be written before issuing the flip. Also we are
likely to wait on that surface in plenty of time before the vblank.
Since we have a mechanism for boosting when a flip misses the expected
vblank, curtain the number of times we RPS boost when simply waiting for
mmioflip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ring switches can occur many times per frame, and are often out of
control, causing frequent RPS boosting for no practical benefit. Treat
the sw semaphore synchronisation as a separate client and only allow it
to boost once per busy/idle cycle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This trims a little overhead from the common case of not needing to
synchronize between rings.
v2: execlists is special and likes to duplicate code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, we only track the last request globally across all engines.
This prevents us from issuing concurrent read requests on e.g. the RCS
and BCS engines (or more likely the render and media engines). Without
semaphores, we incur costly stalls as we synchronise between rings -
greatly impacting the current performance of Broadwell versus Haswell in
certain workloads (like video decode). With the introduction of
reference counted requests, it is much easier to track the last request
per ring, as well as the last global write request so that we can
optimise inter-engine read read requests (as well as better optimise
certain CPU waits).
v2: Fix inverted readonly condition for nonblocking waits.
v3: Handle non-continguous engine array after waits
v4: Rebase, tidy, rewrite ring list debugging
v5: Use obj->active as a bitfield, it looks cool
v6: Micro-optimise, mostly involving moving code around
v7: Fix retire-requests-upto for execlists (and multiple rq->ringbuf)
v8: Rebase
v9: Refactor i915_gem_object_sync() to allow the compiler to better
optimise it.
Benchmark: igt/gem_read_read_speed
hsw:gt3e (with semaphores):
Before: Time to read-read 1024k: 275.794µs
After: Time to read-read 1024k: 123.260µs
hsw:gt3e (w/o semaphores):
Before: Time to read-read 1024k: 230.433µs
After: Time to read-read 1024k: 124.593µs
bdw-u (w/o semaphores): Before After
Time to read-read 1x1: 26.274µs 10.350µs
Time to read-read 128x128: 40.097µs 21.366µs
Time to read-read 256x256: 77.087µs 42.608µs
Time to read-read 512x512: 281.999µs 181.155µs
Time to read-read 1024x1024: 1196.141µs 1118.223µs
Time to read-read 2048x2048: 5639.072µs 5225.837µs
Time to read-read 4096x4096: 22401.662µs 21137.067µs
Time to read-read 8192x8192: 89617.735µs 85637.681µs
Testcase: igt/gem_concurrent_blit (read-read and friends)
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> [v8]
[danvet: s/\<rq\>/req/g]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The merged seqno->request conversion from John called request
variables req, but some (not all) of Chris' recent patches changed
those to just rq. We've had a lenghty (and inconclusive) discussion on
irc which is the more meaningful name with maybe at most a slight bias
towards req.
Given that the "don't change names without good reason to avoid
conflicts" rule applies, so lets go back to a req everywhere for
consistency. I'll sed any patches for which this will cause conflicts
before applying.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
[danvet: s/origina/merged/ as pointed out by Chris - the first
mass-conversion patch was from Chris, the merged one from John.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
v2:
- set the override disable flag too on stepping F0 (mika)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On B0 and C0 steppings the workaround enable bit would be overriden by
default, so the overriding must be disabled.
The WA was added in
commit 83a24979c4
Author: Nick Hoath <nicholas.hoath@intel.com>
Date: Fri Apr 10 13:12:26 2015 +0100
drm/i915/bxt: Add WaForceContextSaveRestoreNonCoherent
Spotted-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our driver compiles clean (nowadays thanks to 0day) but for me, at least,
it would be beneficial if the compiler threw an error rather than a
warning when it found a piece of suspect code. (I use this to
compile-check patch series and want to break on the first compiler error
in order to fix the patch.)
v2: Kick off a new "Debugging" submenu for i915.ko
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add "DRM i915" to the menu name as requested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The macros we use there are the magic ones that can take either dev or
dev_priv. We'd like to move as much as possible towards dev_priv though.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently bxt_resume_prepare() is only used in the runtime-resume path.
Add it to the full S3/S4 path as well.
v2: Rebase on top of the vlv_resume_prepare() shuffling around
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since DRM_ROTATE is counter clockwise (which is compliant with Xrandr),
and HW rotation is clockwise, swapping 90/270 to work as expected from
userspace.
v2: Rebased
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Explain why a few fields of the new pipe_config have their values
preserved, while the others are zeroed.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also make the WA comment consistent with the rest, where the stepping
info is not shown.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ARGB8888 is used for cursors on all platforms so we need to allow it
everywhere.
ABGR8888 is currently only honoured:
- on VLV/CHV in sprite planes
- on SKL+ for primary and sprite planes
so only allow it for those platforms.
Note that we only support ARGB8888/ABGR8888 on the primary plane for
SKL/BXT because we have in line of sight the pipe bottom color on those
platforms and because the primary plane programming on VLV/CHV doesn't
anything different for those formats today.
v2: Fix the logic to forbid the creation ABGR2101010 fbs (Ville)
v3: Still allow the creation of ARGB8888 fbs now that cursor planes use
real fb objects (found by PRTS).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Making lane stagger calculation common for HDMI and DP
v2: Imre's comments addressed
- Remove lane stagger from bxt_clk_div and make it a local variable in
ddi_pll_select
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BUN 1: prop_coeff, int_coeff, tdctargetcnt programming updated and tied to
VCO frequencies. Program i_lockthresh in PORT_PLL_9.
VCO calculated based on the formula:
Desired Output = Port bit rate in MHz (DisplayPort HBR2 is 5400 MHz)
Fast Clock = Desired Output / 2
VCO = Fast Clock * P1 * P2
Prop_coeff, int_coeff, and tdctargetcnt modified according to above
calculation.
BUN 2: Port PLLs require additional programming at certain frequencies -
DCO amplitude in PORT_PLL_10
Review comments from Siva which were addressed in the initial version of the
patch.
- Change PORT_PLL_LOCK_THRESHOLD to PORT_PLL_LOCK_THRESHOLD_MASK
- Calculate for HDMI
- Correct values for vco = 5.4
- return in case of invalid vco range
v2: Imre's review comments addressed
- change dcoampovr_en to dcoampovr_en_h
- change PORT_PLL_DCO_AMP_OVR_EN to PORT_PLL_DCO_AMP_OVR_EN_H
- Correct lane stagger value for 324MHz
- Make coef common for HDMI and DP
- remove superfluous comments
v3: Imre's comments addressed
- Remove Prop_coeff, int_coeff, tdctargetcnt, dcoampovr_en, gain_ctl,
dcoampovr_en_h from bxt_clk_div and make them local variables.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> [v1]
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Be in line with other features that we have.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We just have have VLV and CHV sprites programming the hardware
differently for the ABGR2101010 so keep them working.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That define makes it hard to figure out what is the actual list of
formats at a glance. Expand it then.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika encountered one pathological scenario under X where acquiring all
the mm locks (required to insert a mmu notifier) was very slow, so slow
that by the time we tried to lock the struct_mutex with the usual call
to i915_mutex_lock_interruptible(), X's signal timer had fired causing
us to restart the ioctl (and so looped indefinitely).
While I suspect this is the result of another bug (something leaking mm
perhaps?) we can forgo the error checking and interuptible nature of the
lock here so we only have to pay the expense once and get on with it.
This does expose the userptr creation routine to a driver livelock
though by not being interruptible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Init ret to avoid issues reported by PRTS.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the modeset code is reached with a CRTC that only needs a flip, the
code that assigns PLLs is skipped. But since there is still a state swap
for that CRTC, the current PLL assignment needs to be preserved. I
missed the ddi_pll_sel field in the following commit, which causes
warnings in DDI platforms.
commit 4978cc93d9
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:21 2015 +0300
drm/i915: Preserve shared DPLL information in new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90410
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the following commit, the place where the contents of dpll_hw_state
in crtc_state where zeroed was changed. Prior to that commit, it
happened when the new state was allocated, but now that happens just
before the call the .crtc_compute_clock() hook. The DP code for SKL,
however, sets up the (private) PLL in the encoder compute config
function that has already run by the time that memset() is reached,
causing the previous value to be lost.
This patch fixes the issue by moving the memset() down the call chain,
so that it is only called if the values in dpll_hw_state are going to be
updated.
commit 4978cc93d9
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:21 2015 +0300
drm/i915: Preserve shared DPLL information in new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90462
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reported-and-tested-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add one explicit discard of __iomem address space qualifier in
validate_vbt(), and respect it otherwise. This adds clarity in the code,
and reduces the sparse warnings from the module to just one.
Quoting Daniel, "The vbt really is plain old memory. Except that it's
reserved in the e820 table as something special and hence treated as io
range by the kernel. But it is memory, hence casting away the __iomem is
imo the right approach."
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just so it is grouped logically in line with other data and makes a
rather verbose output a bit shorter.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We never pass a non-NULL vbt to validate_vbt, and we can safely expect
the callers to not change.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville noticed in another patch we we didn't need them at all, so remove
them. It's worth saying that it makes no difference to code generated as
gcc is clever enough to optimize it out.
v2: Remove 'break' after 'return' in switches (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently DSI PLL N1 is hardcoded off. Make it possible to use it
later. This should have no functional changes for now.
v2: s/ffz(~(n))/ffs(n) - 1/ (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added docbook info regarding context save and restore (CSR)
firmware support added from gen9 onwards to drive newly added
DMC (Display microcontroller) in display engine.
v1: Initial version as RFC.
v2: Used "DOC:" tag for csr description based on review comment from Daniel.
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reading from disconnected ports will spit out timeout error
on the dmesg. Skip the attempted read if the port is not
connected and avoid confusing users/testcases about
expected timeouts.
This new dpcd debugfs entry was introduced by commit aa7471d228
("drm/i915: add i915 specific connector debugfs file for DPCD")
v2 by Jani: move the check at the top, out of the loop.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90060
Tested-by: yex.tian@intel.com
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is an extra semi-colon on the if statement so the debug output
always says "Failed to write EDID checksum" even when it didn't fail.
Fixes: 559be30cb7 ('drm/i915: Implement the intel_dp_autotest_edid function for DP EDID complaince tests')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now prefix our functions/enums/data with the first platform it has
been introduced. Do that for the primary plane formats.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: s/gen2/i8xx/ and s/gen4/i965/ ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We advertize C8 in the primary plane formats didn't have the
corresponding code to set PLANE_CTL accordingly.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's be consistent with the others skl_plane_ctl_*() functions and use
a MISSING_CASE(). Not only that, but it's a rude to BUG() the whole
machine here.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No reason to not follow the 80 chars rule, renaming the local variable
makes it easy.
Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We usually use a new line before those kind of return statements. Also
the various skl_plane_ctl*() functions weren't consistent.
Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Improve readability. No functional changes.
v2: use more rational types (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Do not expose invalid gmbus pins as i2c devices to userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Do not expose invalid gmbus pins as i2c devices to userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make input and output of validate_vbt const, and fix the fallout. We
shouldn't modify the VBT, so make the compiler help us here.
v2: use pointer arithmetics on void* to simplify (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make input and output of find_section const, and fix the fallout. We
shouldn't modify the VBT, so make the compiler help us here.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use HOTPLUG_INT_STATUS_G4X instead of HOTPLUG_INT_STATUS_I915 on VLV/CHV
so that we don't confuse the AUX status bits with SDVO status bits.
Avoid pointless log spam as below while handling AUX interrupts:
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x71450064
Note that there's no functional issue, it's just that the sdvo bits
overlap with the dp aux bits. Hence every time we receive an aux
interrupt we also think there's an sdvo hpd interrupt, but due to lack
of any sdvo encoders nothing ever happens because of that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add Ville's explanation why nothing functional really
changes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove some inline keywords. One of the functions has clearly outgrown
it anyway, so let's just leave it to the compiler.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The check for start + length >= total_vm_size is
wrong since start + length can be exactly the size of
the vm.
Fix the check to allow allocation to boundary.
Fixes a regression in commit 4dd738e9cd
("drm/i915: Fix 32b overflow check in gen8_ppgtt_alloc_page_directories")
Testcase: igt/gem_evict_everything/swapping-interruptible
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90399
Tested-by: Lu Hua <huax.lu@intel.com>
Cc: Chris Wilson <chris@chris.wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During check_crtc_state, scaler_id mispatch is being reported for HSW.
This is applicable for skl+ and not for HSW. It is introduced by
commit id:
commit a1b2278e4d
Author: Chandra Konduru <chandra.konduru@intel.com>
Date: Tue Apr 7 15:28:45 2015 -0700
drm/i915: skylake panel fitting using shared scalers
This patch will make sure that we leave scaler_id as 0 for platforms
before skl and set for skl+ only. This way scaler_id check during
check_crtc_state will pass for both prior to skl and skl+ platforms.
v2:
-Leave scaler_id as 0 for gen < 9 (Daniel)
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
References: http://lists.freedesktop.org/archives/intel-gfx/2015-May/065741.html
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we perform the mmio-flip without any locking and then try to acquire
the struct_mutex prior to dereferencing the request, it is possible for
userspace to queue a new pageflip before the worker can finish clearing
the old state - and then it will clear the new flip request. The result
is that the new flip could be completed before the GPU has finished
rendering.
The bugs stems from removing the seqno checking in
commit 536f5b5e86
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Thu Nov 6 11:03:40 2014 +0200
drm/i915: Make mmio flip wait for seqno in the work function
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Synchronising to an object active on the same ring is a no-op, for the
benefit of execbuffer scheduler. However, for CS flips this means that
we can forgo checking whether the last write request of the object is
actually queued and more importantly whether the cache flush for the
write was emitted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We no longer interpolate domains in the same manner, and even if we did,
we should trust setting either of the other write domains would trigger
an invalidation rather than force it. Remove the tweaking of the
read_domains since it serves no purpose and use
i915_gem_object_wait_rendering() directly.
Note that this goes back to
commit a8198eea15
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Apr 13 22:04:09 2011 +0100
drm/i915: Introduce i915_gem_object_finish_gpu()
and gpu domain tracking died in
commit cc889e0f6c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jun 13 20:45:19 2012 +0200
drm/i915: disable flushing_list/gpu_write_list
which is more than 1 year older.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add notes with information dug out of git history.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If an batch ends while the IRQs are not turned on the notification can
go missing and the GPU can hang. So generate a warning in this case.
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In skylake update plane functions, intel_tile_height() is called with
bits_per_pixel instead of pixel_format. Correcting it.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[danvet: Fixup alignment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After feedback from the hardware team, now we set the GPU min/idel freq to RPe.
Punit is expecting us to operate GPU between Rpe & Rp0. If we drop the
frequency to RPn, punit is failing to change the vgg input voltage to
minimum :(
Since Punit validates the rps range [RPe, RP0]. This patch
removes unused cherryview_rps_min_freq function.
v2: Change commit message
v3: set min_freq before idle_freq (chris)
v4: Squash 'Remove unused rps min function' patch
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is observed on BSW that requesting a new frequency from Punit
does nothing when the GPU is in rc6, and if we let GPU enter rc6
with a high frequency, Vnn remains slightly higher than at minimum
frequency. Extending vlv_set_rps_idle() workaround on CHV/BSW.
v2: Update commit msg (Ville)
suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When GPU is idle on VLV, Request freq to punit should be good enough to
get the voltage back to VNN. Also, make sure gfx clock force applies
before requesting the freq fot vlv.
v2: Do forcewake before setting idle frequency (ville)
Update function comments to match the code (Deepak)
v3: Fix get/put across idle frequency Request. (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=75244
suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we're doing throughout the code, being optimistic that platform n + 1
will mostly reuse the same things as platform n allows us to minimize
the enabling work needed.
This time, it's about the number of WM levels.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the recent modeset internal rework, we wind up setting crtc_state->enable
to false, but leave crtc_state->active as true following a
drmModeSetCrtc(fb=0), which is incorrect. This mismatch gets caught by
drm_atomic_crtc_check() and causes subsequent atomic operations (such as plane
updates while the CRTC is disabled) to fail.
Bisect points to
commit dad9a7d6d96630182fb52aae7c3856e9e7285e13
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:19 2015 +0300
drm/i915: Use atomic helpers for computing changed flags
as the commit that actually triggers the regression.
The difference compared to (which this patch reverts)
commit 90d469067d
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Thu May 7 14:31:28 2015 -0700
drm/i915: Set crtc_state->active to false when CRTC is disabled (v2)
is that we know keep state->active/enable in sync for all legacy
modeset paths, as it should be.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Directly squash in the revert and augment the commit
message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Revert "drm/i915: Set crtc_state->active to false when CRTC is disabled (v2)"
This reverts commit 90d469067d.
Skylake nv12 format requires dbuf (aka. ddb) calculations
and programming for each of y and uv sub-planes. Made minor
changes to reuse current dbuf calculations and programming
for uv plane. i.e., with this change, existing computation
is used for either packed format or uv portion of nv12
depending on incoming format. Added new code for dbuf
computation and programming for y plane.
This patch is a pre-requisite for adding NV12 format support.
Actual nv12 support is coming in later patches.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fix spelling typo in intel_runtime_pm.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVWh3TAAoJEHm+PkMAQRiG/kwH/2c9irodp2+M9OUnX2bfsBb6
LnChiDpvkF5BB8jhP6d/XmvPp4NJzAbTxByhjdfb2E2HkorCUHCOIn2tI1TE2pUs
2qjkOVH+XCzoV0goGtQjzK1ht8f2IrtlDiEjyRekK5cJHzhggb22QPtWL4npyd0O
reDmG2jsRaF9POr9uLSFEv4CEnkksmRLUU0vuQX0TZeCJ41O7TXrkN/wKrLZ5mj4
IWpqXQaSlrffq/T5HnVbXBxk3/T8QmhrIoppiMpV1mUVj0uTqlFRNi5qwT2Nit1h
FVljWI4+WgOk3bf7fUlp+ahopjkTgu+GuXkiRP/pdgWNQO0cxCWSAzSndAlIIAE=
=uOoJ
-----END PGP SIGNATURE-----
Backmerge v4.1-rc4 into into drm-next
We picked up a silent conflict in amdkfd with drm-fixes and drm-next,
backmerge v4.1-rc5 and fix the conflicts
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/drm_irq.c
Scattering of random drm core patches. Bunch of atomic prep work too, but
the final bits for blob properties, atomic modesets and lifting the
experimental tag on the atomic ioctl are still blocked on Daniel Stone
finalizing and testing the weston support for it. I hope that we can get
it all ready for 4.2 though.
* tag 'topic/drm-misc-2015-05-19' of git://anongit.freedesktop.org/drm-intel: (22 commits)
drm/atomic: Allow drivers to subclass drm_atomic_state, v3
drm/atomic: remove duplicated assignment of old_plane_state
drm/dp: Fix comment in DP helper
drm/atomic: add drm_atomic_get_existing_*_state helpers
drm/core: get rid of -Iinclude/drm
drm/i915: get rid of -Iinclude/drm
drm/atomic-helpers: Export drm_atomic_helper_update_legacy_modeset_state
drm/atomic-helpers: Update vblank timestamping constants
drm/sysfs: remove unnecessary connector type checks
drm/sysfs: split DVI-I and TV-out attributes
drm/sysfs: make optional attribute groups per connector type
drm/sysfs: add a helper for extracting connector type from kobject
drm/edid: Add CEA modes before inferred modes
drm/prime: Allow internal imports without import_sg_table
drm: Add reference counting to blob properties
drm: Introduce blob_lock
drm: Introduce helper for replacing blob properties
drm: Don't leak path blob property when updating
drm/atomic: Don't open-code CRTC state destroy
drm/edid: Add DMT modes with ID > 0x50
...
Commit c9f038a1a5 ("drm/i915: Don't assume primary & cursor are
always on for wm calculation (v4)") fixes a null pointer dereference.
Setting the primary and cursor panes to false in
ilk_compute_wm_parameters to false does however give the following
errors in the kernel log and causes the screen to flicker.
[ 101.133716] [drm:intel_set_cpu_fifo_underrun_reporting [i915]]
*ERROR* uncleared fifo underrun on pipe A
[ 101.133725] [drm:intel_cpu_fifo_underrun_irq_handler [i915]]
*ERROR* CPU pipe A FIFO underrun
Always setting the panes to enabled fixes this error.
Helped-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Thomas Gummerer <t.gummerer@gmail.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This results in a warning when building out of tree:
"cc1: warning: include/drm: No such file or directory [enabled by default]"
Most code already uses #include <drm/foo.h> correctly, so fix the
instances that don't.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fixes a timing issue that causes a GPU hang when the system
comes out of power saving.
During pm_resume, We are submitting batchbuffers before enabling
Interrupts this is causing us to miss the context switch interrupt,
and in consequence intel_execlists_handle_ctx_events is not triggered.
This patch is based on a patch from Deepak S <deepak.s@intel.com>
from another platform.
The patch fixes an issue introduced by:
commit e7778be1ea
drm/i915: Fix startup failure in LRC mode after recent init changes
The above patch added a call to init_context() to fix an issue introduced
by a previous patch. But, it then opened up a small timing window for the
batches being added by the init_context (basically setting up the context)
to complete before the interrupts have been turned on, thus hanging the
GPU.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89600
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: fixed typo in subject, massaged the comments a bit]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently vlv_wait_port_ready() waits for all four lanes on the
appropriate channel. This no longer works on CHV when the unused
lanes may be power gated. So pass in a mask of lanes that the
caller is expecting to be ready.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_parse_cmds returns -EACCES on chained batches, which "tells the
caller to abort and dispatch the workload as a non-secure batch",
but the mechanism implementing that was broken when
flags |= I915_DISPATCH_SECURE was moved from i915_gem_execbuffer_parse
to i915_gem_do_execbuffer (17cabf571e):
i915_gem_execbuffer_parse returns the original batch_obj in this case,
and i915_gem_do_execbuffer doesn't check for that.
Don't set the secure bit in this case to make sure such batches don't
run with elevated priviledges.
Signed-off-by: Rebecca Palmer <rebecca_palmer@zoho.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Stitch together commit message. Also remove a comment as
suggested by Mika. And style-align the comment while at it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also treat it as a proper boolean.
Cc: Todd Previte <tprevite@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We do not yet support tiled objects bigger than the mappable
aperture size so reject them.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[danvet: Rework the check a bit to avoid warnings.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With recent hardware/firmware there don't appear to be any glitches
on the other PHY when we toggle the cmnreset for the other PHY. So
detangle the cmnlane power wells from one another and let them be
controlled independently.
This reverts commit 3dd7b97458.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sometimes (exactly when is a bit unclear) DISPLAY_PHY_CONTROL appears to
get corrupted. The values I've managed to read from it seem to have some
pattern but vary quite a lot. The corruption doesn't seem to just happen
when the register is accessed, but can also happen spontaneosly during
modeset. When this happens during a modeset things go south and the
display doesn't light up.
I've managed to hit the problemn when toggling HDMI on port D on and
off. When things get corrupted the display doesn't light up, but as soon
as I manually write the correct value to the register the display comes
up.
First I was suspicious that we ourselves accidentally overwrite it with
garbage, but didn't catch anything with the reg_rw tracepoint. Also I
sprinkled check all over the modeset path to see exactly when the
corruption happens, and eg. the read back value was fine just before
intel_dp_set_m(), and corrupted immediately after it. I also made my
check function repair the register value whenever it was wrong, and with
this approach the corruption repeated several times during the modeset
operation, always seeming to trigger in the same exact calls to the
check function, while other calls to the function never caught anything.
So far I've not seen this problem occurring when carefully avoiding all
read accesses to DISPLAY_PHY_CONTROL. Not sure if that's just pure luck
or an actual workaround, but we can hope it works. So let's avoid reading
the register and instead track the desired value of the register in dev_priv.
v2: Read out the power well state to determine initial register value
v3: Use DPIO_CHx names instead of raw numbers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set up the chv display PHY lane stagger registers according to
"Programming Guide for 1273 CHV eDP/DP/HDMI Display PHY" v1.04
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like it was introduced in:
commit 650ad970a3
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Apr 18 16:35:02 2014 +0300
drm/i915: vlv: factor out vlv_force_gfx_clock and check for pending force-of
but I'm not sure why. It has caused problems for us in the past (see
85250ddff7 "drm/i915/chv: Remove Wait for a previous gfx force-off"
and 8d4eee9cd7 "drm/i915: vlv: increase timeout when forcing on the
GFX clock") and doesn't seem to be required, so let's just drop it.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Cc: stable@vger.kernel.org # c9c52e2419: drm/i915/chv: Remove Wait ...
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Repick this commit from
5df0582bf0 becuase Dave Airlie lost it
in his merge commit e1dee1973c74a0408b108d88c57a15be8a2d6d84.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With the recent modeset internal rework, we wind up setting
crtc_state->enable to false, but leave crtc_state->active as true, which
is incorrect. This mismatch gets caught by drm_atomic_crtc_check() and
causes subsequent atomic operations (such as plane updates while the
CRTC is disabled) to fail.
Bisect points to
commit dad9a7d6d96630182fb52aae7c3856e9e7285e13
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:19 2015 +0300
drm/i915: Use atomic helpers for computing changed flags
as the commit that actually triggers the regression.
v2: Update to alter in-flight state rather than already-committed state
(first version was accidentally based on a midpoint of Ander's
modeset rework series, before his final patches that add proper
state swapping to the legacy modeset path).
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Testcase: igt/kms_universal_plane
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A part of this function was indented with 2 tabs and 1 space instead of
just 2 tabs. We're going to touch that code, so start by re-indenting
it.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use partial view for huge BOs (bigger than half the mappable aperture)
in fault handler so that they can be accessed withough trying to make
room for them by evicting other objects.
v2:
- Only use partial views in the case where early rejection was
previously done.
- Account variable type changes from previous reroll.
v3:
- Add a comment about overwriting existing page entries.
(Tvrtko Ursulin)
- Whitespace fixes.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Partial view type allows manipulating parts of huge BOs through the GGTT,
which was not previously possible due to constraint that whole object had
to be mapped for any access to it through GGTT.
v2:
- Retain error value from sg_alloc_table (Tvrtko Ursulin)
- Do not zero already zeroed variable (Tvrtko Ursulin)
- Use more common variable types for page size/offset (Tvrtko Ursulin)
v3:
- Only compare additional view parameters when need to (Tvrtko Ursulin)
v4:
- Do zero out the variable that needs to be (bug introduced in v2).
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Do not skip special GGTT views when considering whether an object
is pinned or not.
Wrong behaviour was introduced in;
commit ec7adb6ee7
Author: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Date: Mon Mar 16 14:11:13 2015 +0200
drm/i915: Do not use ggtt_view with (aliasing) PPGTT
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GGTT VMA sizes might be smaller than the whole object size due to
different GGTT views.
v2:
- Separate GGTT view constraint calculations from normal view
constraint calculations (Chris Wilson)
v3:
- Do not bother with debug wording. (Tvrtko Ursulin)
v4:
- Clearer logic for calculating map_and_fenceable (Tvrtko Ursulin)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[danvet: Drop BUG_ON, it's redudant.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reading a single value from the object, the locking only provides futile
protection against userspace races. The locking is useless so remove it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Renaming gen9_rates to skl_rates because other platforms may have different
supported rates.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we do proper state swaps, we don't depend on this function
anymore to keep the state in sync.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the commit output state function with a simple swap of states.
Note that we still need to reconcile the legacy state after the swap,
since there are still code that relies on those.
Also note that even though changes to the state of a crtc different than
the one passed as an argument to __intel_set_mode() will be saved, the
modeset logic still deals with only one crtc.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use lower level calls to better integrate with the modeset code and
allow a full state swap in a follow up patch.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When a new pipe_config is calculated, the fields related to shared dplls
are reset, under the assumption that they will be recalculated as part
of the modeset, which is true with the current state of the code.
As we convert to atomic, however, it will be possible to calculate a new
pipe_config and skip the modeset. In that case, after the state swap we
still want the shared dplls to be preserved.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To match the behavior of ->atomic_commit().
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the drivers own logic for computing mode_changed, active_changed
and planes_changed flags with the check_modeset() atomic helper. Since
that function needs to compare the crtc's new mode with the current,
this patch also moves the set up of crtc_state->mode earlier in the call
chain.
Note that for the call to check_plane() to work properly, we need to
check new plane state against new crtc state. But since we still use the
plane update helper, which doesn't have a full atomic state, we need to
hack around that in intel_plane_atomic_check().
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In a follow up patch the function that computes mode changes will be
replaced with the one from the atomic helpers. To preserve the behavior
of legacy modeset forcing DPMS on, that function will need to detect a
change in the active state of the crtc, so that has to be kept up to
date.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is no longer necessary since we only update the staged config on
successfull modeset. The new configuration is stored in an atomic state
struct which is freed in case of failure.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The logic that stages the state before the modeset was still updating
first the old staged config and then populating the atomic state based
on that. Change this to use only the atomic state.
Note that now the staged config is updated in the function
intel_modeset_commit_output_state(). This is done so that the modeset
check and the force restore path in the hw state read out code continue
to work.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a helper function to make the code slightly more readable.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Call intel_set_mode() uncondionally from intel_crtc_set_config(), since
the former function is now properly wired to ignore all the modesets if
the mode_changed and active_changed flags are false in crtc_state.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the atomic state instead.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the similar fields in crtc_state instead, so that this code can be
moved to our future implementation of atomic_check().
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't need to pass it down the call chain anymore now that the plane
state is set up properly.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the primary plane state to the legacy modeset atomic state and use
it when configuring the primary plane in __intel_set_mode(). This is a
first step towards merging the flip path in intel_crtc_set_config() and
__intel_set_mode().
v2: Set crtc to NULL if fb is NULL. (Maarten)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The modeset code is now properly divided in two phases, so that it only
changes hardware state if it succeeds, so there's no ill-effect that
needs to be undone on failure anymore.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The remaining parts of the failure path could only be reached if the
allocation of crtc_state_copy would fail. In that case, there is nothing
to undo, so just get rid of the label for error handling and return an
error code immediately.
We also always allocate a pipe_config, even if the pipe is being
disabled, so the remaining part of what was the error/done case can be
simplified a little too.
v2: Ignore return value from drm_plane_helper_update(). (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The first function calls done in that function can still cause changes
to the atomic state and may fail. This should eventually be part of our
atomic check function, while the rest of the code in __intel_set_mode()
is the commit hook. So this makes the legacy mode set more atomic-y.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no way that function can fail after it sets crtc->mode anymore,
so there's no need to save the old mode for the failure case.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set the mode_changed field on the crtc_states and use that instead.
Note that even though this patch doesn't completely replace the logic in
intel_modeset_affected_pipes(), that logic was never fully used to its
full extent. Since the commit mentioned below, modeset_pipes and
prepare_pipes would only contain at most the pipe for which the set_crtc
ioctl was called. We can grow back that logic when the time comes.
commit b6c5164d7b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 12 18:48:43 2013 +0200
drm/i915: Fixup Oops in the pipe config computation
v2: Don't set mode_changed unconditionally for modeset_crtc. (Ander)
Check for needs_modeset() before trying to allocate a PLL. (Ander)
Only call .crtc_enable() for pipes that were disabled. (Maarten)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the current implementation of intel_modeset_affected_pipes(), if a
pipe will be enabled then it is in modeset_pipes. We'll remove that mask
in a follow up patch, but want to preserve this behavior, so just make
that explicit.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code in intel_modeset_pipe_config() still needs changes before it
can calculate more than just one pipe_config, and pretending it can will
only make those changes more difficult.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function intel_modeset_compute_config() needs to eventually become
part of atomic_check(). At that point, all the affected crtcs need to be
in the atomic state with the new values. So move the logic of adding
crtc states out of that function.
v2: Set crtc_state->enable in all cases. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should make the conversion to atomic easier, by splitting the
initialization of the atomic state from the logic that decides if a
modeset is needed.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simplifies looping over connector states a bit.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the helpers introduced by the commit below to properly initialize
the duplicated states.
commit f5e7840b0c
Author: Thierry Reding <treding@nvidia.com>
Date: Wed Jan 28 14:54:32 2015 +0100
drm/atomic: Add helpers for state-subclassing drivers
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is not necessary after the below commit.
commit a0211bb482
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Mon Mar 30 14:05:43 2015 +0300
drm/atomic: Don't try to free a NULL state
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes disabling planes more explicit.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[anderco: fixed warning due to using drm_crtc instead of intel_crtc]
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To make it clear that it isn't called during crtc enable.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're the same code, so why not?
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was an optimization from way back before we had primary plane
support to be able to disable the primary plane. But with primary
plane support userspace can tell the kernel this directly, so there's
no big need for this any more. And it's getting in the way of the
atomic conversion.
If need be we can resurrect this later on properly again.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Explain why removing this is ok.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows disabling all planes affecting a crtc without caring what type it is.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is used by the next commit to disable all planes on a crtc
without caring what type it is.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some of the flags that were used are still useful when transitioning
to atomic, so keep those around for now. This removes some of the
complications of crtc->primary_enabled, making it easier to remove.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
