Here support is added for responding to DSP IRQs that are used to
indicate data being available on the DSP. The idea is that we check the
amount of data available upon receipt of an IRQ and on subsequent calls
to the pointer callback we recheck once less than one fragment is
available (to avoid excessive SPI traffic), if there is truely less than
one fragment available we ack the last IRQ and wait for a new one.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't want to use a bypassed write in wm5110_clear_pga_volume,
we might disable the DRE whilst the CODEC is powered down. A
normal regmap_write will always go to the hardware (when not on
cache_only) even if the written value matches the cache. As using
a normal write will still achieve the desired behaviour of bring
the cache and hardware in sync, this patch updates the function
to use a normal write, which avoids issues when the CODEC is
powered down.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The bitwise OR has higher precedence than ?: so the val2 was always set
to 0x2.
Fixes: b4c83b1715 ('ASoC: rsnd: add Multi channel support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 3c83ac2325 ("ASoC: hdac_hdmi: check error return") fixes
the static checker warning reported by Dan Carpenter:
sound/soc/codecs/hdac_hdmi.c:416 hdac_hdmi_parse_and_map_nid()
warn: unsigned 'hdac->num_nodes' is never less than zero.
But it doesn't fix the issue completely.
It's also a failure if no sub nodes found for an afg node. So modify
the return condition appropriately.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default the device latches data on the falling edge of the
BCLK in DSP mode, whereas the expectation for normal BCLK is to
latch on the rising edge. This updates the driver to invert the
BCLK configuration for DSP mode, to align with expected behaviour.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a device would like to use delayed suspending then PM
recommendation is to set ‘power.use_autosuspend’ flag. To allow
users to do so we need to change runtime calls in core to use
autosuspend counterparts.
For user who do not wish to use delayed suspend not setting the
device's ‘power.use_autosuspend’ flag will result in non-delayed
suspend even with these APIs which incidentally is also the default
behaviour, so only users will be impacted who opt in for this.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default the device latches data on the falling edge of the
BCLK in DSP mode, whereas the expectation for normal BCLK is to
latch on the rising edge. This updates the driver to invert the
BCLK configuration for DSP mode, to align with expected behaviour.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register ASRCFG is volatile, but some bits need to be recovered
after suspend/resume.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BIOS for the HP ElitePad 1000 G2 uses an unexpected HID,
(INTCCFFD), add it to the white list of knowns HIDs.
Signed-off-by: Jorge Fernandez Monteagudo <jorgefm@cirsa.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The machine driver is not loaded when the BIOS uses the 10EC5642
_HID. Add it to the white list of known _HIDs, codec_name is
already taken care of by previous commit
Tested on Asus T100TAF.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec name is hard-coded in machine driver, pass information
from actual ACPI HID to help support BIOS variations
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
based on bytcr-rt5640 with changes only on codec side
Quirk logic is kept as placeholder.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 95f0980148
"ASoC: Intel: Move apci find machine routines"
introduced a regression in ACPI probe of the DPCM driver.
Fix by conditionally compiling sst-acpi when the DPCM driver
is not selected
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sound is noisy when using BCLK as reference, enable ASRC in rt5640
codec
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This provide the fix for firmware memory by freeing the pointer in driver
remove where it is safe to do so
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
IRQ reaction time is not immediate when headset putton is pressed.
This patch shortens the reaction time.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Constify the ACPI device ID array, no need to have it writable at
runtime. Also drop the unused RT5645_INIT_REG_LEN define.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Bard Liao <bardliao@realtek.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_to_hdac_dev() and to_ehdac_device() instead of open-coding.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 9b8ef9f6b3 ("ASoC: dapm: Add startup & shutdown for dai_links")
Added support for calling startup on CODEC to CODEC links, however this
is called with a NULL runtime pointer. There isn't really a sensible way
to pass a valid runtime pointer to a CODEC to CODEC link at the moment,
so we need to make the startup function safe for NULL runtimes.
This patch returns from the Arizona startup function early if there is no
runtime, this is perfectly safe as all the startup function does is set
the PCM constraints for user-space which arn't relevant to a CODEC to
CODEC link anyway.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Field usrcnt is unsigned so it cannot be lesser than zero.
The patch fixes the check, moves it to the beginning of the function
and changes return value to -EIO in case of usercnt error.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of call sites were missed when the snd_soc_dapm_mutex_lock
function was added this patch fixes those up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add system clock detection to prevent output DC from SPO.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQ pin will keep high when the headset button is pressed. And
keep low when the headset button is released. So, we need irq trigger
at both edges. However, some platform can't support it. Therefore,
we polling the register to report the button release event once a
button presse event is received.
To support the headset button detection function for those can't
support both edges trigger platforms, we also need to invert the
polarity of jack detection irq since we need to keep the IRQ pin
low in normal case.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial silicon did not have master bias enabled by default, unlike
later HW, so use regmap patch to align with newer defaults.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For a sample rate of 12kHz the bclk was taken from the 44.1kHz table as
we test for a multiple of 8kHz. This patch fixes this issue by testing
for multiples of 4kHz instead.
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add required tables and the binding document for ACPI and OF matching.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.
- Conversion of the array of DAI links to a list by Mengdong Lin,
supporting dynamically adding and removing DAI links.
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production. We really need to get to the
point where that can be done.
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come.
- New drivers for a number of Imagination Technologies IPs.
- Lots of new features and cleanups for the Renesas drivers.
- ANC support for WM5110.
- New driver for Atmel class D speaker drivers.
- New drivers for Cirrus CS47L24 and WM1831.
- New driver for Dialog DA7128.
- New drivers for Realtek RT5659 and RT56156.
- New driver for Rockchip RK3036.
- New driver for TI PC3168A
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWee4AAAoJECTWi3JdVIfQwPkH/jMpijne8cfnOm0jQ0WyvXPd
HSig93ZAJ2x/+uR7yrmF2BsxhnT6G1lmDb2zxYhHGEAMyBtdA/xtOjO1wTRjXgIo
9p7ui66uP/sAW+NfHsvXVyf/8vV9nw8t0CsyBf+ijynz6MiDigQR7e8RA7xZR7oQ
oBabHPZb85OJjxmn2XlqaxUoxNhBdAS3gNoctMy9VZDwSLiunOvYTGBoBA43LQk6
6DN5VRu7wg05ruN6t5xZ5bd5WAtvgN+tSsRAabmunWDnILCa8OaOmzWPv3QITIva
PQLauiya4N0/YgyNGYaBY/6pc5u9SHzq0caYUq0I6WY6Phjo7wfU8/+y4NqUPn4=
=d18k
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.5
This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.
- Conversion of the array of DAI links to a list by Mengdong Lin,
supporting dynamically adding and removing DAI links.
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production. We really need to get to the
point where that can be done.
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come.
- New drivers for a number of Imagination Technologies IPs.
- Lots of new features and cleanups for the Renesas drivers.
- ANC support for WM5110.
- New driver for Atmel class D speaker drivers.
- New drivers for Cirrus CS47L24 and WM1831.
- New driver for Dialog DA7128.
- New drivers for Realtek RT5659 and RT56156.
- New driver for Rockchip RK3036.
- New driver for TI PC3168A
There is a status bit on RT5677_PLL1_CTRL2 and RT5677_PLL2_CTRL2.
That's why those registers are set volatile. However, the status
bit is currently not used by codec driver. So, it should be no
problem if we set them non-volatile.
The purpose of setting them non-volatile is to restore the setting
after a syspend/resume cycle.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stream is created whilst the compressed stream is opened and a
buffer is created when the DSP powers up. It is necessary at a point
once both the DSP has powered up and the the stream has been opened to
connect a stream to a buffer on the DSP. This is done in the trigger
callback as this is after the DSP has been powered and obviously the
stream must be open. Note that whilst the connect is currently trivial
it is expected that this will get more complex when support for multiple
buffers/streams per DSP is added.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code that locates and initialises the buffer of compressed data on
the DSP if the firmware supported compressed data capture. The buffer
struct (wm_adsp_compr_buf) is kept separate from the stream struct
(wm_adsp_compr) this will allow much easier support of multiple
streams of data from the one DSP in the future, although support for
this will not be added in this patch chain.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow user-space to open a compressed stream, although no data will be
passed yet, as part of this adding the ability to define supported
capabilities per firmware and check these match the stream being opened.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register a platform driver for the CODEC and add DAIs that will be used
to connect a compressed record path for the voice control functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PLL mode based on 32KHz master clock not supported in
AB silicon so remove support from the driver.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HW can provide 1.6V micbias level as well the existing levels
already provided in the driver. This patch adds support for 1.6V
to the DT binding.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In AB silicon, the internal LDO is not supported so remove
DT and driver references to this (digital voltage direct from
'VDD' supply)
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current AB silicon, BIAS_EN field is enabled by default in the
REFERENCES register, so the regmap default value should reflect
this.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If codec probe() function fails after supplies have been enabled
it should really tidy up and disable them again. This patch updates
the probe function to do just that.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously Sidetone would operate only when capture to DAI was in
progress, due to DAPM path configuration. There is no reason why
this should not operate without DAI capture, so this patch updates
the DAPM path accordingly.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl_ssi uses different stream names ("AC97 Playback" / "AC97 Capture")
in AC'97 mode so in this case fsl-asoc-card route map should
also be using them.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 8kHz, 11.025kHz, 16kHz, 22.05kHz output sample rate support.
According referance menual, "Limited support for the case when
output sampling rates is between 8kHz and 30kHz. The limitation
is the supported ratio (Fsin/Fsout) range as between 1/24 to 8."
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes the audio play can not be resumed after it is
suspended. Add snd_soc_pm_ops to execute power management
operations, then this issue is fixed.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NULL test on call to devm_kzalloc.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NULL test on call to devm_kzalloc.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add NULL test on call to devm_kzalloc.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
* x = devm_kzalloc(...);
... when != x == NULL
*x
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return type "unsigned int" was used by the ssm2518_lookup_mcs()
function even though it will eventually return a negative error code.
Improve this implementation detail by deletion of the type modifier then.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Multi channel support on Renesas R-Car sound.
This patch is tested on Salvator-X board, but it can't use
Multi channel, because supported format is different between
codec chip and R-Car.
Thus, it was tested on board which doesn't mount codec chip,
with oscilloscope.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to the codec driver to handle mic level
detect related IRQs, and report these to user-space using a uevent
variable.
The uevent variable string "EVENT=MIC_LEVEL_DETECT" is sent to
user-space, if the mic level detect feature is enabled, and the
audio captured at the chosen mic(s) is above a certain threshold.
User-space can then handle the event accordingly (e.g. process
audio capture stream).
This method was chosen over ALSA control notification for a couple
of reasons:
1) There's no requirement here for a control to read state from.
The event is the only thing that's required and of interest.
2) tinyalsa support for control notifications does not exist so on
platforms using this over alsa-lib there is a need to add code
to support this event handling.
Another possible option would be to use the standard Jack reporting
framework but this really does not fit for this kind of event.
Finally, use of the input device framework is not being encouraged,
due to difficulties in enabling apps to access input devices, so
this has also been avoided.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An external amp (if any) is connected to the external outputs of the SoC
of course, rather then directly to the internal amp.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AFE is actually allowed to be turn on before configuration of DAIs
since each DAI has its own enabling control. Turn on/off AFE in
runtime resume/suspend to avoid AFE being shut down when closing a DAI
while other DAIs are still active.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The upstreamed code modified the control names from Mute to
Switch without changing the logic. To get audio working the Switch
needs to be off which isn't aligned with normal ALSA conventions.
Inverting the logic now so that Switch Off means mute and Switch On
means active audio using the specific volume setting.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the fields channels_min, channels_max, rate and formats are
irrelevant for compressed playback, they will depend on the
content. This was probably a copy-paste mistake to have
them in the first place
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add dai links to enable additional playback stream with deeper
buffer for lower power consumption.
The normal and DEEP_buffer streams are not mutually exclusive,
content will be mixed by the DSP.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add definitions for MERR_DPCM_DEEP_BUFFER AND PIPE_MEDIA3_IN
Add relevant cpu-dai and dai link names
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All the functionality was merged in DPCM-based driver,
keep older driver to avoid breaking userspace but
tag it as unsupported/deprecated
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge DMI quirks for various machines such as Asus T100
and clean-up code
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
first renaming and reducing delta with byt-rt5640 code before
dmi-based quirks are enabled
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
initial cleanup to use same pins
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using the hw_fixup function in order to overwrite the default SSP
setting for Audio DSP port connected to the codec. Instead of
TDM 4ch use I2S 2ch 24 bits.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When pipeline is deleted, set the pipeline state to invalid state.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds clean up routine to clear the stream registers and
calls this routine before setting up stream registers.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
