Re-initialize rs when we get a rate_update hook called which
happens when remote STA changes bandwidth or sends a VHT opmode
notification.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Change old UAPSD bit to PM_CMD_SUPPORT, and add a new bit to indicate
real UAPSD support.
Don't use UAPSD when the firmware doesn't support it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
At the firmware level, IBSS support has similar programming
requirements as AP/GO support, so use the same functions with
just small differences.
With IBSS only a single virtual interface can be used, so no
changes in the advertised interface combinations are needed.
For now, don't use hardware crypto for the GTKs in IBSS mode,
the firmware should support it though.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
BT Coex needs to be updated when the bandwidth is modified
by the AP.
While at it, remove the vif parameter from
bt_coex_vif_change since it was unused.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some NICs embedded in platforms that have only 16 Tx queues,
this affect the mapping of the Tx queues.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the new API for BT Coex. The full functionality
will be implemented in further patches.
Note: this disables BT Coex for the currently existing
fw (-7 version).
There is also a new command - the channel inhibition command.
This command tells BT what channels to avoid in order to
minimise the interaction between BT and WiFi.
We can tell BT about 2 channels, primary and secondary.
BT will not tune to primary at all and will avoid secondary
as much as possible.
This also means that we need to track vifs that AP / GO.
So rename iwl_mvm_bt_coex_vif_assoc to
iwl_mvm_bt_coex_vif_change to better reflect its real
meaning.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for scheduled scan according to firmware support.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New FW doesn't use the SSID from scan request template. Adding
a TLV flag to indicate the change, and fixing the flows to send
the first SSID in SSID list if the flag is on.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use beacon statistics notification handler
to notify bt coex about rssi changes.
Mac80211's mechanism is not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When firmware restart happens, the timers are obviously reset and
the new firmware has no synchronisation with the AP as we program
timings to the pre-restart values. The firmware should attempt to
synchronise by itself, but in multi-channel scenarios this isn't
easy, particularly since it has to try to keep service quality up
for other MACs.
To make it more reliable, give each client MAC some time to catch
beacons when restarting or resuming. Service quality was impacted
anyway (or in resume doesn't really matter much.)
Reviewed-by: Moshe Island <moshe.island@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a testmode command to (manually) disable (and re-enable)
beacon filtering for testing purposes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing, implement setting continuous NoA duration
using a new MVM-specific testmode command.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use beacon statistics notification to track RSSI.
Notify mac80211 when the tresholds are crossed.
The roaming treshold is configured to be
equal to cqm_thold. If the beacon filtering command
is not supported by fw fall back and use mac80211
mechanism.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement basic uAPSD client support adding the following:
- Advertise uAPSD support in HW capabilities
- Set all ACs trigger- and delivery-enabled
- Set max SP length to 2 buffered frames
- Assign QNDP with the highest TID with no mandatory admission
control required
- Set uAPSD related parameters in Power Table command
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_mac_add_interface() didn't clean up beacon filtering
configuration and ctxt allocation in some error cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This feature is fully supported by iwlwmvm, so advertise
it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change beacon filtering command due to a change in the API.
In case the FW supports the old API, we do not send the
BF HCMD and assume that since the corresponding struct in
the FW is zeroed by default then we don't need to disable
it in the FW actively.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current registered the per-vif debugfs handler for
STA mode only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Support Tx power limitations. These limitations can come from
mac80211 for various reasons.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The managed interface PS was not disabled when a GO interface
was added. As a consequence, when the station VMAC was in PS,
the GO also was not on the medium. Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there one vif on 5GHz associating, it would clear all
the BT Coex constraints. This can't work if there is
another vif on 2.4GHz. Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change power management implementation to support new host-device API
containing uAPSD parameters. Verify FW support for this new API.
Use the new power table command (0xA9) to configure power management.
Use the legacy command (0x77) if FW does not support the new API.
New file power_legacy.c is introduced for legacy implementation.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to a firmware bug, it crashes when the beacon interval
is smaller than 16. Avoid this by refusing the station state
change creating the AP station, causing mac80211 to abandon
the attempt to connect to the AP, and eventually wpa_s to
blacklist it.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware / HW can't support more than 16 Rx BA sessions.
Deny any attemps to open more sessions than that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
This was missing and prevented any further attempts
to load the module.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
iwlmvm does not support concurrent operation of AP with P2P Client/GO.
Update the interface limits to reflect that iwlmvm supports only
concurrent operation of station with AP and P2P Client/GO.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code moved and is now far away from the code that takes
the mutex.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently beacon availability upon association is marked by have_beacon
flag of assoc_data structure that becomes unavailable when association
completes. However beacon availability indication is required also after
association to inform a driver. Currently dtim_period parameter is used
for this purpose. Move have_beacon flag to another structure, persistant
throughout a interface's life cycle. Use suitable sematics for beacon
availability indication.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[fix another instance of BSS_CHANGED_DTIM_PERIOD in docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In unassociated BSS STA mode FW verifies both power save and power
management flags to decide on switching power off. The driver currently
sets power management flag according to mac80211 decision. As result, in
unassociated mode power management flag is down and power consumption is
high. Change power management enablement. When unassociated in BPS and
LP power save modes enable power management regardless of mac80211
decision. Rely on mac80211 decision if associated. Add power management
state update during associated/disassociated modes transitions.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently vif_count verification for power management enablement appear
in different places. Move these verifications to one place in
iwl_mvm_update_power_mode().
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge to get the wil6210 changes that a cfg80211 change needs.
A conflict in drivers/net/wireless/ath/ath9k/init.c was just
whitespace changes.
Also fix a semantic conflict due to cw1200 using WoWLAN which
I had modified in my tree.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit eebfc9394e.
This wasn't intended to be included here, my mistake. I
accidentally merged a mac80211 fixes tree here that had
this change, when it wasn't even intended to be there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware supports periodic keep alive and beacon monitoring,
so advertise connection monitor offload capability by setting
IEEE80211_HW_CONNECTION_MONITOR flag. Implement missed beacons
notification handler. Call ieee80211_beacon_loss in case of
missed beacons, so AP probing by mac80211 can be triggered.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to avoid NIC destruction due to high temperature,
CT kill will power down the NIC.
To avoid this, thermal throttling will decrease throughput
to prevent the NIC from reaching the temperature at which
CT kill is performed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately, advertising P2P_DEVICE support was a little
premature, a number of issues came up in testing and have
been fixed for 3.10. Rather than try to backport all the
different fixes, disable P2P_DEVICE support in the drivers
using it. For iwlmvm that implies disabling P2P completely
as it can't support P2P operation w/o P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the counter for non-AMPDU frames to mvm. It is needed
for the drain flow which happens once the ieee80211_sta has
been freed, so keeping it in iwl_mvm_sta which is embed into
ieee80211_sta is not a good idea.
Also, since its purpose it to remove the STA in the fw only
after all the frames for this station have exited the shared
Tx queues, we need to decrement it in the reclaim flow. This
flow can happen after ieee80211_sta has been removed, which
means that we have no iwl_mvm_sta there. So we can't know
what is the vif type. Hence, we know audit these frames for
all the vif types.
In order to avoid spawning sta_drained_wk all the time, we
now check that we are in a flow in which draining might
happen - only when mvmsta is NULL. This is better than
previous code that would spawn sta_drained_wk all the time
in AP mode.
Cc: stable@vger.kernel.org [3.9]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without this command, the firmware will filter out all the
multicast frames. Let them all in as for now. Later we will
want to optimize this to save power.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
