This will trigger new context memory to be rediscovered and allocated
during the re-probe process after a firmware reset. Without this, the
newly reset firmware does not have valid context memory and the driver
will eventually fail to allocate some resources.
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic needs to check both bp->total_irqs and the reserved IRQs in
hw_resc->resv_irqs if applicable and see if both are enough to cover
the L2 and RDMA requested vectors. The current code is only checking
bp->total_irqs and can fail in some code paths, such as the TX timeout
code path with the RDMA driver requesting vectors after recovery. In
this code path, we have not reserved enough MSIX resources for the
RDMA driver yet.
Fixes: 75720e6323 ("bnxt_en: Keep track of reserved IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same bnxt_flash_package_from_file() function to support
devlink flash operation.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Currently, the driver does not allow PHY settings on a multi-function or
NPAR NIC whose port is shared by more than one function. Newer
firmware now allows PHY settings on some of these NICs. Check for
this new firmware setting and allow the user to set the PHY settings
accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If the link settings have been changed by another function sharing the
port, firmware will send us an async. message. In response, we will
call the new bnxt_init_ethtool_link_settings() function to update
the current settings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Refactor this logic in bnxt_probe_phy() into a separate function
bnxt_init_ethtool_link_settings(). It used to be that the settable
link settings will never be changed without going through ethtool.
So we only needed to do this once in bnxt_probe_phy(). Now, another
function sharing the port may change it and we may need to re-initialize
the ethtool settings again in run-time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
New firmware allows PHY loopback to be set without disabling autoneg
first. Check this capability and skip disabling autoneg when
it is supported by firmware. Using this scheme, loopback will
always work even if the PHY only supports autoneg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The driver currently only assignes 1 RSS context to each VF. This works
for the Linux VF driver. But other drivers, such as DPDK, can make use
of additional RSS contexts. Modify the code to divide up and assign
RSS contexts to VFs just like other resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Some chips that need host context memory as a backing store requires
the memory to be initialized to a non-zero value. Query the
value from firmware and initialize the context memory accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Driver calls HWRM_FUNC_RESET firmware call while resuming the device
which clears the context memory backing store. Because of which
allocating firmware resources would eventually fail. Fix it by freeing
all context memory during suspend and reallocate the memory during resume.
Call bnxt_hwrm_queue_qportcfg() in resume path. This firmware call
is needed on the 57500 chips so that firmware will set up the proper
queue mapping in relation to the context memory.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
After driver unregister, firmware is erasing the information that
driver supports new resource management. Send FUNC_RESOURCE_QCAPS
command to inform the firmware that driver supports new resource
management while resuming from hibernation. Otherwise, we fallback
to the older resource allocation scheme.
Also, move driver register after sending FUNC_RESOURCE_QCAPS command
to be consistent with the normal initialization sequence.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Everytime driver registers with firmware, driver is required to
register for async event notifications as well. These 2 calls
are done using the same firmware command and can be combined.
We are also missing the 2nd step to register for async events
in the suspend/resume path and this will fix it. Prior to this,
we were getting only default notifications.
ULP can register for additional async events for the RDMA driver,
so we add a parameter to the new function to only do step 2 when
it is called from ULP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In the bnxt_init_one() failure path, if the driver has already called
firmware to register the driver, it is not undoing the driver
registration. Add this missing step to unregister for correctness,
so that the firmware knows that the driver has unloaded.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Disable Bus master during suspend to prevent DMAs after the device
goes into D3hot state. The new 57500 devices may continue to DMA
from context memory after the system goes into D3hot state. This
may cause some PCIe errors on some system. Re-enable it during resume.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Fix BNXT_CHIP_NUM_5645X() to include 57452 and 56454 chip IDs, so
that these chips will be properly classified as P4 chips to take
advantage of the P4 fixes and features.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-11-20
The following pull-request contains BPF updates for your *net-next* tree.
We've added 81 non-merge commits during the last 17 day(s) which contain
a total of 120 files changed, 4958 insertions(+), 1081 deletions(-).
There are 3 trivial conflicts, resolve it by always taking the chunk from
196e8ca748:
<<<<<<< HEAD
=======
void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
>>>>>>> 196e8ca748
<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca748
<<<<<<< HEAD
if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
/* kmalloc()'ed memory can't be mmap()'ed */
if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca748
The main changes are:
1) Addition of BPF trampoline which works as a bridge between kernel functions,
BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
BPF programs for tracing with practically zero overhead to call into BPF (as
opposed to k[ret]probes) and ii) attachment of the former to networking related
programs to see input/output of networking programs (covering xdpdump use case),
from Alexei Starovoitov.
2) BPF array map mmap support and use in libbpf for global data maps; also a big
batch of libbpf improvements, among others, support for reading bitfields in a
relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.
3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.
4) Add BPF audit support and emit messages upon successful prog load and unload in
order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.
5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
(XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.
6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
call named bpf_get_link_xdp_info() for retrieving the full set of prog
IDs attached to XDP, from Toke Høiland-Jørgensen.
7) Add BTF support for array of int, array of struct and multidimensional arrays
and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.
8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.
9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
xdping to be run as standalone, from Jiri Benc.
10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.
11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.
12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is especially beneficial during the NVRAM related firmware
commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND
flag gets set while waiting for firmware response, abort and return
error.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During loss of heartbeat, log this warning message.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NVM params that are not supported in the current NVM
configuration, return the error as -EOPNOTSUPP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report health status update to devlink health reporter, once
reset is completed.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux driver is capable of being the master function to handle
resets, so we set the flag to let firmware know. Some other
drivers, such as DPDK, is not capable and will not set the flag.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware supports hot reset, extend ETHTOOL_RESET to support
hot reset driver which does not require a driver reload after
ETHTOOL_RESET. The driver will go through the same coordinated
reset sequence as a firmware initiated fatal/non-fatal reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the larger HWRM_COREDUMP_TIMEOUT value for coredump related
data response from the firmware. These commands take longer than
normal commands.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware reports RX buffer errors, the latest 57500 chips do not
require reset. The packet is discarded by the hardware and the
ring will continue to operate.
Also, add an rx_buf_errors counter for this type of error. It can help
the user to identify if the aggregation ring is too small.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aRFS ring table interface has changed for the 57500 chips. Updating
it accordingly so it will work with the latest production firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to bpf_map's refcnt/usercnt, convert bpf_prog's refcnt to atomic64
and remove artificial 32k limit. This allows to make bpf_prog's refcounting
non-failing, simplifying logic of users of bpf_prog_add/bpf_prog_inc.
Validated compilation by running allyesconfig kernel build.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191117172806.2195367-3-andriin@fb.com
Fix the array overrun while keeping the eth_addr and eth_addr_mask
pointers as u16 to avoid unaligned u16 access. These were overlooked
when modifying the code to use u16 pointer for proper alignment.
Fixes: 90f906243b ("bnxt_en: Add support for L2 rewrite")
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Inform the RDMA driver to stop/start during suspend/resume. The
RDMA driver needs to stop and start just like error recovery.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Notify the RDMA driver by calling the bnxt_ulp_stop()/bnxt_ulp_start()
hooks during error recovery. The current ULP IRQ start/stop
sequence in error recovery (which is insufficient) is replaced with the
full reset sequence when we call bnxt_ulp_stop()/bnxt_ulp_start().
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We call bnxt_ulp_stop() to notify the RDMA driver that some error or
imminent reset is about to happen. After that we always call
some variants of bnxt_close().
In the next patch, we will integrate the recently added error
recovery with the RDMA driver. In response to ulp_stop, the
RDMA driver may free MSIX vectors and that will also trigger
bnxt_close(). To avoid bnxt_close() from being called twice,
we set a new flag after ulp_stop is called. If the RDMA driver
frees MSIX vectors while the new flag is set, we will not call
bnxt_close(), knowing that it will happen in due course.
With this change, we must make sure that the bnxt_close() call
after ulp_stop will reset IRQ. Modify bnxt_reset_task()
accordingly if we call ulp_stop.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decap (VXLAN tunnel) flow rules are not getting offloaded with
upstream kernel. This is because TC block callback infrastructure has
been updated to use indirect callbacks to get offloaded rules from
other higher level devices (such as tunnels), instead of ndo_setup_tc().
Since the decap rules are applied to the tunnel devices (e.g, vxlan_sys),
the driver should register for indirect TC callback with tunnel devices
to get the rules for offloading. This patch updates the driver to
register and process indirect TC block callbacks from VXLAN tunnels.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides support for modifying L3/L4 Header parameters to support NAT.
Sets the appropriate fields/bits in cfa_flow_alloc cmd.
Sample cmd for offloading an IPv4 flow with SNAT:
ovs-ofctl add-flow ovsbr0 "ip,nw_src=192.168.201.44 \
actions=mod_nw_src:203.31.220.144,output:p7p1"
Replace 'nw_src' with 'nw_dst' in above cmd for DNAT with IPv4
Sample cmd for offloading an IPv4 flow with SNAPT:
ovs-ofctl add-flow ovsbr0 "ip,nw_src=192.168.201.44 \
actions=mod_nw_src:203.31.220.144, mod_tp_src:6789,output:p7p1"
Similar to DNAT, replace 'tp_src' with 'tp_dst' for offloading flow
with DNAPT
Sample cmd for offloading an IPv6 flow with SNAT:
ovs-ofctl add-flow ovsbr0 "ipv6, ipv6_src=2001:5c0:9168::2/64 \
actions=load:0x1->NXM_NX_IPV6_SRC[0..63], \
load:0x20010db801920000->NXM_NX_IPV6_SRC[64..127],output:p7p1"
Replace 'SRC' with DST' above for IPv6 DNAT
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For every single case where bnxt_tc_can_offload() can fail, we are
logging a user friendly descriptive message anyway, but because of the
path it would take in case of failure, another redundant error message
would get logged. Just freeing the node and returning from the point of
failure should suffice.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for packet edit offload of L2 fields (src mac &
dst mac, also referred as L2 rewrite). Only when the mask is fully exact
match for a field, the command is sent down to the adapter to offload
such a flow. Otherwise, an error is returned.
v2: Fix pointer alignment issue in bnxt_fill_l2_rewrite_fields() [MChan]
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver supports 2 types of core dumps.
1. Live dump - Firmware dump when system is up and running.
2. Crash dump - Dump which is collected during firmware crash
that can be retrieved after recovery.
Crash dump is currently supported only on specific 58800 chips
which can be retrieved using OP-TEE API only, as firmware cannot
access this region directly.
User needs to set the dump flag using following command before
initiating the dump collection:
$ ethtool -W|--set-dump eth0 N
Where N is "0" for live dump and "1" for crash dump
Command to collect the dump after setting the flag:
$ ethtool -w eth0 data Filename
v3: Modify set_dump to support even when CONFIG_TEE_BNXT_FW=n.
Also change log message to netdev_info().
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In error recovery process when firmware indicates that it is
completely down, initiate a firmware reset by calling OP-TEE API.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use true/false for bool type in bnxt_timer function.
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recently added error recovery logic, the device may already
be disabled if the firmware recovery is unsuccessful. In
bnxt_remove_one(), check that the device is still enabled first
before calling pci_disable_device().
Fixes: 3bc7d4a352 ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
When firmware indicates that driver needs to invoke firmware reset
which is common for both error recovery and live firmware reset path,
driver needs a different time to wait before polling for firmware
readiness.
Modify the wait time to fw_reset_min_dsecs, which is initialised to
correct timeout for error recovery and firmware reset.
Fixes: 4037eb7156 ("bnxt_en: Add a new BNXT_FW_RESET_STATE_POLL_FW_DOWN state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The current code does not do endian swapping between the devlink
parameter and the internal NVRAM representation. Define a union to
represent the little endian NVRAM data and add 2 helper functions to
copy to and from the NVRAM data with the proper byte swapping.
Fixes: 782a624d00 ("bnxt_en: Add bnxt_en initial port params table and register it")
Cc: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The current code that rounds up the NVRAM parameter bit size to the next
byte size for the devlink parameter is not always correct. The MSIX
devlink parameters are 4 bytes and we don't get the correct size
using this method.
Fix it by adding a new dl_num_bytes member to the bnxt_dl_nvm_param
structure which statically provides bytesize information according
to the devlink parameter type definition.
Fixes: 782a624d00 ("bnxt_en: Add bnxt_en initial port params table and register it")
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
During health reporter operations, driver might want to fill-up
the extack message, so propagate extack down to the health reporter ops.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new state is required when firmware indicates that the error
recovery process requires polling for firmware state to be completely
down before initiating reset. For example, firmware may take some
time to collect the crash dump before it is down and ready to be
reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some error recovery updates to the spec., among other minor changes.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware coredump messages take much longer than standard messages,
so increase the timeout accordingly.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the BNXT_STATE_OPEN flag instead of netif_running() in
bnxt_set_rx_mode(). If the driver is going through any reset, such
as firmware reset or even TX timeout, it may not be ready to set the RX
mode and may crash. The new rx mode settings will be picked up when
the device is opened again later.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function bnxt_get_registered_vfs() to handle the work
of getting the number of registered VFs under #ifdef CONFIG_BNXT_SRIOV.
The main code will call this function and will always work correctly
whether CONFIG_BNXT_SRIOV is set or not.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Health show command example and output:
$ devlink health show pci/0000:af:00.0 reporter fw_fatal
pci/0000:af:00.0:
name fw_fatal
state healthy error 1 recover 1 grace_period 0 auto_recover true
Fatal events from firmware or missing periodic heartbeats will
be reported and recovery will be handled.
We also turn on the support flags when we register with the firmware to
enable this health and recovery feature in the firmware.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This call will handle fatal firmware errors by forcing a reset on the
firmware. The master function driver will carry out the forced reset.
The sequence will go through the same bnxt_fw_reset_task() workqueue.
This fatal reset differs from the non-fatal reset at the beginning
stages. From the BNXT_FW_RESET_STATE_ENABLE_DEV state onwards where
the firmware is coming out of reset, it is practically identical to the
non-fatal reset.
The next patch will add the periodic heartbeat check and the devlink
reporter to report the fatal event and to initiate the bnxt_fw_exception()
call.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This state handles driver initiated chip reset during error recovery.
Only the master function will perform this step during error recovery.
The next patch will add code to initiate this reset from the master
function.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag to mark that the firmware has encountered fatal condition.
The driver will not send any more firmware messages and will return
error to the caller. Fix up some clean up functions to continue
and not abort when the firmware message function returns error.
This is preparation work to fully handle firmware error recovery
under fatal conditions.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retain the VF MAC address, default VLAN, TX rate control, trust settings
of VFs after firmware reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health reporter for the firmware reset event. Once we get
the notification from firmware about the impending reset, the driver
will report this to devlink and the call to bnxt_fw_reset() will be
initiated to complete the reset sequence.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the bnxt_fw_reset() main function to handle firmware reset. This
is triggered by firmware to initiate an orderly reset, for example
when a non-fatal exception condition has been detected. bnxt_fw_reset()
will first wait for all VFs to shutdown and then start the
bnxt_fw_reset_task() work queue to go through the sequence of reset,
re-probe, and re-initialization.
The next patch will add the devlink reporter to start the sequence and
call bnxt_fw_reset().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This event from firmware signals a coordinated reset initiated by the
firmware. It may be triggered by some error conditions encountered
in the firmware or other orderly reset conditions.
We store the parameters from this event. Subsequent patches will
add logic to handle reset itself using devlink reporters.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create new FW devlink_health_reporter, to know the current health
status of FW.
Command example and output:
$ devlink health show pci/0000:af:00.0 reporter fw
pci/0000:af:00.0:
name fw
state healthy error 0 recover 0
FW status: Healthy; Reset count: 1
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new flag will be set in subsequent patches when firmware is
going through reset. If bnxt_close() is called while the new flag
is set, the FW reset sequence will have to be aborted because the
NIC is prematurely closed before FW reset has completed. We also
reject SRIOV configurations while FW reset is in progress.
v2: No longer drop rtnl_lock() in close and wait for FW reset to complete.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the async event from the firmware that enables firmware health
monitoring. Store initial health metrics.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-map the GRC registers for periodic firmware health monitoring.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call the new firmware API HWRM_ERROR_RECOVERY_QCFG if it is supported
to discover the firmware health and recovery capabilities and settings.
This feature allows the driver to reset the chip if firmware crashes and
becomes unresponsive.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During IF_UP, newer firmware has a new status flag that indicates that
firmware has reset. Add new function bnxt_fw_init_one() to re-probe the
firmware and re-setup VF resources on the PF if necessary. If the
re-probe fails, set a flag to prevent bnxt_open() from proceeding again.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs need to be reconfigured dynamically after firmwware reset, the
configuration sequence on the PF needs to be changed to register the VF
buffers first. Otherwise, some VF firmware commands may not succeed as
there may not be PF buffers ready for the re-directed firmware commands.
This sequencing did not matter much before when we only supported
the normal bring-up of VFs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the hardware/firmware configuration portion in
bnxt_sriov_enable() into a new function bnxt_cfg_hw_sriov(). This
new function can be called after a firmware reset to reconfigure the
VFs previously enabled.
v2: straight refactor of the code. Reordering done in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the new firmware reset feature, some of the logic
in bnxt_init_one() and related functions will be called again after
firmware has reset. Reset some of the flags and capabilities so that
everything that can change can be re-initialized. Refactor some
functions to probe firmware versions and capabilities. Check some
buffers before allocating as they may have been allocated previously.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the silent parameter is set, suppress all messages when there is
no response from firmware. When polling for firmware to come out of
reset, no response may be normal and we want to suppress the error
messages. Also, don't poll for the firmware DMA response if Bus Master
is disabled. This is in preparation for error recovery when firmware
may be in error or reset state or Bus Master is disabled.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 4 functions handling message forwarding for SR-IOV. They
check for non-zero firmware response code and then return -1. There
is no need to do this anymore. The main messaging function will
now return standard error code. Since we don't need to examine the
response, we can use the hwrm_send_message() variant which will
take the mutex automatically.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main firmware messaging function returns the firmware defined error
code and many callers have to convert to standard error code for proper
propagation to userspace. Convert bnxt_hwrm_do_send_msg() to return
standard error code so we can do away with all the special error code
handling by the many callers.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the non-standard -1 code with -EBUSY when there is no firmware
response after waiting for the maximum timeout.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same message is printed 3 times in the code, so use a common function
to do that.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit added logic to determine the appropriate statistics block
size to allocate and the size is stored in bp->hw_ring_stats_size. But
if the firmware spec is older than 1.6.0, it is 0 and not initialized.
This causes the allocation to fail with size 0 and bnxt_open() to
abort. Fix it by always initializing bp->hw_ring_stats_size to the
legacy default size value.
Fixes: 4e74850663 ("bnxt_en: Allocate the larger per-ring statistics block for 57500 chips.")
Reported-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW expects the driver to provide unique flow reference handles
for Tx or Rx flows. When a Tx flow and an Rx flow end up sharing
a reference handle, flow offload does not seem to work.
This could happen in the case of 2 flows having their L2 fields
wildcarded but in different direction.
Fix to incorporate the flow direction as part of the L2 key
v2: Move the dir field to the end of the bnxt_tc_l2_key struct to
fix the warning reported by kbuild test robot <lkp@intel.com>.
There is existing code that initializes the structure using
nested initializer and will warn with the new u8 field added to
the beginning. The structure also packs nicer when this new u8 is
added to the end of the structure [MChan].
Fixes: abd43a1352 ("bnxt_en: Support for 64-bit flow handle.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Direction of the flow is determined using src_fid. For an RX flow,
src_fid is PF's fid and for TX flow, src_fid is VF's fid. Direction
of the flow must be specified, when getting statistics for that flow.
Currently, for DECAP flow, direction is determined incorrectly, i.e.,
direction is initialized as TX for DECAP flow, instead of RX. Because
of which, stats are not reported for this DECAP flow, though it is
offloaded and there is traffic for that flow, resulting in flow age out.
This patch fixes the problem by determining the DECAP flow's direction
using correct fid. Set the flow direction in all cases for consistency
even if 64-bit flow handle is not used.
Fixes: abd43a1352 ("bnxt_en: Support for 64-bit flow handle.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For newly added NVM parameters, older firmware may not have the support.
Suppress the error message to avoid the unncessary error message which is
triggered when devlink calls the driver during initialization.
Fixes: 782a624d00 ("bnxt_en: Add bnxt_en initial params table and register it.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If FW returns FRAG_ERR in response error code, driver is resending the
command only when HWRM command returns success. Fix the code to resend
NVM_INSTALL_UPDATE command with DEFRAG install flags, if FW returns
FRAG_ERR in its response error code.
Fixes: cb4d1d6261 ("bnxt_en: Retry failed NVM_INSTALL_UPDATE with defragmentation flag enabled.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both RX buffers and RX aggregation buffers have to be
replenished at the end of NAPI, post the RX aggregation buffers first
before RX buffers. Otherwise, we may run into a situation where
there are only RX buffers without RX aggregation buffers for a split
second. This will cause the hardware to abort the RX packet and
report buffer errors, which will cause unnecessary cleanup by the
driver.
Ringing the Aggregation ring doorbell first before the RX ring doorbell
will prevent some of these buffer errors. Use the same sequence during
ring initialization as well.
Fixes: 697197e5a1 ("bnxt_en: Re-structure doorbells.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device shutdown, the VNIC clearing sequence needs to be modified
to free the VNIC first before freeing the RSS contexts. The current
code is doing the reverse and we can get mis-directed RX completions
to CP ring ID 0 when the RSS contexts are freed and zeroed. The clearing
of RSS contexts is not required with the new sequence.
Refactor the VNIC clearing logic into a new function bnxt_clear_vnic()
and do the chip specific VNIC clearing sequence.
Fixes: 7b3af4f75b ("bnxt_en: Add RSS support for 57500 chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
This cleans up a lot of unneeded code and logic around the debugfs
files, making all of this much simpler and easier to understand.
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the 57508, 57504, and 57502 chip IDs that are all part of the
BNXT_CHIP_P5 family of chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new TPA feature in the 57500 chips, we need to discover the
feature first before setting up the netdev features. Refactor the
the firmware probe and init logic more cleanly into 2 functions and
and make these calls before setting up the netdev features.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the new expanded TPA v2 counters on 57500 B0 chips for
ethtool -S.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new TPA implemantation has additional TPA counters that extend the
per-ring statistics block. Allocate the proper size accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code assumes that the per ring statistics counters are
fixed. In newer chips that support a newer version of TPA, the
TPA counters are also changed. Refactor the code by defining these
counter names in arrays so that it is easy to add a new array for
a new set of counters supported by the newer chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a more optimized hardware GRO function to setup the SKB on 57500
chips. Some workaround code is no longer needed on 57500 chips and
the pseudo checksum is also calculated in hardware, so no need to
do the software pseudo checksum in the driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new TPA feature on 57500 supports a larger number of concurrent TPAs
(up to 1024) divided among the functions. We need to add some logic to
map the hardware TPA ID to a software index that keeps track of each TPA
in progress. A 1:1 direct mapping without translation would be too
wasteful as we would have to allocate 1024 TPA structures for each RX
ring on each PCI function.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the previous refactoring, the TPA fast path can now be
modified slightly to support TPA on the new chips. The main
difference is that the agg completions are retrieved differently using
the bnxt_get_tpa_agg_p5() function on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 57500 chips, hardware GRO mode cannot be determined from the TPA
end, so we need to check bp->flags to determine if we are in hardware
GRO mode or not. Modify bnxt_set_features so that the TPA flags
in bp->flags don't change until the device is closed. This will ensure
that the fast path can safely rely on bp->flags to determine the
TPA mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 2 GRO functions to set up the hardware GRO SKB fields for 2
different hardware chips have practically identical logic for
tunneled packets. Refactor the logic into a separate bnxt_gro_tunnel()
function that can be used by both functions.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the new 57500 chips, these new RX_AGG completions are not coalesced
at the TPA_END completion. Handle these by storing them in the
array in the bnxt_tpa_info struct, as they are seen when processing
the CMPL ring.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an aggregation array to bnxt_tpa_info struct to keep track of the
aggregation completions. The aggregation completions are not
completed at the TPA_END completion on 57500 chips so we need to
keep track of them. The array is only allocated on the new chips
when required. An agg_count field is also added to keep track of the
number of these completions.
The maximum concurrent TPA is now discovered from firmware instead of
the hardcoded 64. Add a new bp->max_tpa to keep track of maximum
configured TPA.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the TPA logic slightly, so that the code can be more easily
extended to support TPA on the new 57500 chips. In particular, the
logic to get the next aggregation completion is refactored into a
new function bnxt_get_agg() so that this operation is made more
generalized. This operation will be different on the new chip in TPA
mode. The logic to recycle the aggregation buffers has a new start
index parameter added for the same purpose.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new chips have a slightly modified TPA interface for LRO/GRO_HW.
Modify the TPA structures so that the same structures can also be
used on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Among the changes are new CoS discard counters and new ctx_hw_stats_ext
struct for the latest 5750X B0 chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While using net_dim, a dim_sample was used without ever initializing the
comps value. Added use of DIV_ROUND_DOWN_ULL() to prevent potential
overflow, it should not be a problem to save the final result in an int
because after the division by epms the value should not be larger than a
few thousand.
[ 1040.127124] UBSAN: Undefined behaviour in lib/dim/dim.c:78:23
[ 1040.130118] signed integer overflow:
[ 1040.131643] 134718714 * 100 cannot be represented in type 'int'
Fixes: 398c2b05bb ("linux/dim: Add completions count to dim_sample")
Signed-off-by: Yamin Friedman <yaminf@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
