It just makes it harder to see 1) what the code is doing
and 2) grep for all users of dst{->,.}neighbour
Signed-off-by: David S. Miller <davem@davemloft.net>
IPV6, unlike IPV4, doesn't have a routing cache.
Routing table entries, as well as clones made in response
to route lookup requests, all live in the same table. And
all of these things are together collected in the destination
cache table for ipv6.
This means that routing table entries count against the garbage
collection limits, even though such entries cannot ever be reclaimed
and are added explicitly by the administrator (rather than being
created in response to lookups).
Therefore it makes no sense to count ipv6 routing table entries
against the GC limits.
Add a DST_NOCOUNT destination cache entry flag, and skip the counting
if it is set. Use this flag bit in ipv6 when adding routing table
entries.
Signed-off-by: David S. Miller <davem@davemloft.net>
The message size allocated for rtnl ifinfo dumps was limited to
a single page. This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.
Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit c3968a857a
('ipv6: RTA_PREFSRC support for ipv6 route source address selection')
added support for ipv6 prefsrc as an alternative to ipv6 addrlabels,
but it did not work because the prefsrc entry was not copied.
Cc: Daniel Walter <sahne@0x90.at>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make dst_alloc() and it's users explicitly initialize the entire
entry.
The zero'ing done by kmem_cache_zalloc() was almost entirely
redundant.
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolved logic conflicts causing a build failure due to
drivers/net/r8169.c changes using a patch from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes introduced with git-commit a02e4b7d ("ipv6: Demark default
hoplimit as zero.") missed to remove the hoplimit initialization. As a
result, ipv6_get_mtu interprets the return value of dst_metric_raw
(-1) as 255 and answers ping6 with this hoplimit. This patche removes
the line such that ping6 is answered with the hoplimit value
configured via sysctl.
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ipv6] Add support for RTA_PREFSRC
This patch allows a user to select the preferred source address
for a specific IPv6-Route. It can be set via a netlink message
setting RTA_PREFSRC to a valid IPv6 address which must be
up on the device the route will be bound to.
Signed-off-by: Daniel Walter <dwalter@barracuda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids explicit cast to avoid 'discards qualifiers'
compiler warning in a netfilter patch that i've been working on.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I intend to turn struct flowi into a union of AF specific flowi
structs. There will be a common structure that each variant includes
first, much like struct sock_common.
This is the first step to move in that direction.
Signed-off-by: David S. Miller <davem@davemloft.net>
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=29252
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=30462
In commit d80bc0fd26 ("ipv6: Always
clone offlink routes.") we forced the kernel to always clone offlink
routes.
The reason we do that is to make sure we never bind an inetpeer to a
prefixed route.
The logic turned on here has existed in the tree for many years,
but was always off due to a protecting CPP define. So perhaps
it's no surprise that there is a logic bug here.
The problem is that we canot clone a route that is already a
host route (ie. has DST_HOST set). Because if we do, an identical
entry already exists in the routing tree and therefore the
ip6_rt_ins() call is going to fail.
This sets off a series of failures and high cpu usage, because when
ip6_rt_ins() fails we loop retrying this operation a few times in
order to handle a race between two threads trying to clone and insert
the same host route at the same time.
Fix this by simply using the route as-is when DST_HOST is set.
Reported-by: slash@ac.auone-net.jp
Reported-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a dst pointer which is potentitally error encoded.
Don't pass original dst pointer by reference, pass a struct net
instead of a socket, and elide the flow argument since it is
unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch issuing these commands:
fd = open("/proc/sys/net/ipv6/route/flush")
unshare(CLONE_NEWNET)
write(fd, "stuff")
would flush the newly created net, not the original one.
The equivalent ipv4 code is correct (stores the net inside ->extra1).
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0dbaee3b37 (net: Abstract default ADVMSS behind an
accessor.) introduced a possible crash in tcp_connect_init(), when
dst->default_advmss() is called from dst_metric_advmss()
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows avoiding multiple writes to the initial __refcnt.
The most simplest cases of wanting an initial reference of "1"
in ipv4 and ipv6 have been converted, the rest have been left
along and kept at the existing "0".
Signed-off-by: David S. Miller <davem@davemloft.net>
If we didn't have a routing cache, we would not be able to properly
propagate certain kinds of dynamic path attributes, for example
PMTU information and redirects.
The reason is that if we didn't have a routing cache, then there would
be no way to lookup all of the active cached routes hanging off of
sockets, tunnels, IPSEC bundles, etc.
Consider the case where we created a cached route, but no inetpeer
entry existed and also we were not asked to pre-COW the route metrics
and therefore did not force the creation a new inetpeer entry.
If we later get a PMTU message, or a redirect, and store this
information in a new inetpeer entry, there is no way to teach that
cached route about the newly existing inetpeer entry.
The facilities implemented here handle this problem.
First we create a generation ID. When we create a cached route of any
kind, we remember the generation ID at the time of attachment. Any
time we force-create an inetpeer entry in response to new path
information, we bump that generation ID.
The dst_ops->check() callback is where the knowledge of this event
is propagated. If the global generation ID does not equal the one
stored in the cached route, and the cached route has not attached
to an inetpeer yet, we look it up and attach if one is found. Now
that we've updated the cached route's information, we update the
route's generation ID too.
This clears the way for implementing PMTU and redirects directly in
the inetpeer cache. There is absolutely no need to consult cached
route information in order to maintain this information.
At this point nothing bumps the inetpeer genids, that comes in the
later changes which handle PMTUs and redirects using inetpeers.
Signed-off-by: David S. Miller <davem@davemloft.net>
When an IPSEC SA is still being set up, __xfrm_lookup() will return
-EREMOTE and so ip_route_output_flow() will return a blackhole route.
This can happen in a sndmsg call, and after d33e455337 ("net: Abstract
default MTU metric calculation behind an accessor.") this leads to a
crash in ip_append_data() because the blackhole dst_ops have no
default_mtu() method and so dst_mtu() calls a NULL pointer.
Fix this by adding default_mtu() methods (that simply return 0, matching
the old behavior) to the blackhole dst_ops.
The IPv4 part of this patch fixes a crash that I saw when using an IPSEC
VPN; the IPv6 part is untested because I don't have an IPv6 VPN, but it
looks to be needed as well.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please note that the IPSEC dst entry metrics keep using
the generic metrics COW'ing mechanism using kmalloc/kfree.
This gives the IPSEC routes an opportunity to use metrics
which are unique to their encapsulated paths.
Signed-off-by: David S. Miller <davem@davemloft.net>
They are bogus. The basic idea is that I wanted to make sure
that prefixed routes never bind to peers.
The test I used was whether RTF_CACHE was set.
But first of all, the RTF_CACHE flag is set at different spots
depending upon which ip6_rt_copy() caller you're talking about.
I've validated all of the code paths, and even in the future
where we bind peers more aggressively (for route metric COW'ing)
we never bind to prefix'd routes, only fully specified ones.
This even applies when addrconf or icmp6 routes are allocated.
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing metrics are now copy-on-write.
Initially a route entry points it's metrics at a read-only location.
If a routing table entry exists, it will point there. Else it will
point at the all zero metric place-holder called 'dst_default_metrics'.
The writeability state of the metrics is stored in the low bits of the
metrics pointer, we have two bits left to spare if we want to store
more states.
For the initial implementation, COW is implemented simply via kmalloc.
However future enhancements will change this to place the writable
metrics somewhere else, in order to increase sharing. Very likely
this "somewhere else" will be the inetpeer cache.
Note also that this means that metrics updates may transiently fail
if we cannot COW the metrics successfully.
But even by itself, this patch should decrease memory usage and
increase cache locality especially for routing workloads. In those
cases the read-only metric copies stay in place and never get written
to.
TCP workloads where metrics get updated, and those rare cases where
PMTU triggers occur, will take a very slight performance hit. But
that hit will be alleviated when the long-term writable metrics
move to a more sharable location.
Since the metrics storage went from a u32 array of RTAX_MAX entries to
what is essentially a pointer, some retooling of the dst_entry layout
was necessary.
Most importantly, we need to preserve the alignment of the reference
count so that it doesn't share cache lines with the read-mostly state,
as per Eric Dumazet's alignment assertion checks.
The only non-trivial bit here is the move of the 'flags' member into
the writeable cacheline. This is OK since we are always accessing the
flags around the same moment when we made a modification to the
reference count.
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not handle PMTU vs. route lookup creation any differently
wrt. offlink routes, always clone them.
Reported-by: PK <runningdoglackey@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove (unnecessary) casts to make code cleaner.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first big packets sent to a "low-MTU" client correctly
triggers the creation of a temporary route containing the reduced MTU.
But after the temporary route has expired, new ICMP6 "packet too big"
will be sent, rt6_pmtu_discovery will find the previous EXPIRED route
check that its mtu isn't bigger then in icmp packet and do nothing
before the temporary route will not deleted by gc.
I make the simple experiment:
while :; do
time ( dd if=/dev/zero bs=10K count=1 | ssh hostname dd of=/dev/null ) || break;
done
The "time" reports real 0m0.197s if a temporary route isn't expired, but
it reports real 0m52.837s (!!!!) immediately after a temporare route has
expired.
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like RTAX_ADVMSS, make the default calculation go through a dst_ops
method rather than caching the computation in the routing cache
entries.
Now dst metrics are pretty much left as-is when new entries are
created, thus optimizing metric sharing becomes a real possibility.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all RTAX_ADVMSS metric accesses go through a new helper function,
dst_metric_advmss().
Leave the actual default metric as "zero" in the real metric slot,
and compute the actual default value dynamically via a new dst_ops
AF specific callback.
For stacked IPSEC routes, we use the advmss of the path which
preserves existing behavior.
Unlike ipv4/ipv6, DecNET ties the advmss to the mtu and thus updates
advmss on pmtu updates. This inconsistency in advmss handling
results in more raw metric accesses than I wish we ended up with.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is for consistency with ipv4. Using "-1" makes
no sense.
It was made this way a long time ago merely to be consistent
with how the ipv6 socket hoplimit "default" is stored.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to hide all direct accesses, especially writes,
to dst_entry metrics values.
This will allow us to:
1) More easily change how the metrics are stored.
2) Implement COW for metrics.
In particular this will help us put metrics into the inetpeer
cache if that is what we end up doing. We can make the _metrics
member a pointer instead of an array, initially have it point
at the read-only metrics in the FIB, and then on the first set
grab an inetpeer entry and point the _metrics member there.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
1. IPV6_TLV_TEL_DST_SIZE
This has not been using for several years since created.
2. RT6_INFO_LEN
commit 33120b30 kill all RT6_INFO_LEN's references, but only this definition remained.
commit 33120b30cc
Author: Alexey Dobriyan <adobriyan@sw.ru>
Date: Tue Nov 6 05:27:11 2007 -0800
[IPV6]: Convert /proc/net/ipv6_route to seq_file interface
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gives users at least some clue as to what the problem
might be and how to go about fixing it.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There're some percpu_counter list corruption and poison overwritten warnings
in recent kernel, which is resulted by fc66f95c.
commit fc66f95c switches to use percpu_counter, in ip6_route_net_init, kernel
init the percpu_counter for dst entries, but, the percpu_counter is never destroyed
in ip6_route_net_exit. So if the related data is freed by kernel, the freed percpu_counter
is still on the list, then if we insert/remove other percpu_counter, list corruption
resulted. Also, if the insert/remove option modifies the ->prev,->next pointer of
the freed value, the poison overwritten is resulted then.
With the following patch, the percpu_counter list corruption and poison overwritten
warnings disappeared.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "Pekka Savola (ipv6)" <pekkas@netcore.fi>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct dst_ops tracks number of allocated dst in an atomic_t field,
subject to high cache line contention in stress workload.
Switch to a percpu_counter, to reduce number of time we need to dirty a
central location. Place it on a separate cache line to avoid dirtying
read only fields.
Stress test :
(Sending 160.000.000 UDP frames,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_TRIE, SLUB/NUMA)
Before:
real 0m51.179s
user 0m15.329s
sys 10m15.942s
After:
real 0m45.570s
user 0m15.525s
sys 9m56.669s
With a small reordering of struct neighbour fields, subject of a
following patch, (to separate refcnt from other read mostly fields)
real 0m41.841s
user 0m15.261s
sys 8m45.949s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AnyIP is the capability to receive packets and establish incoming
connections on IPs we have not explicitly configured on the machine.
An example use case is to configure a machine to accept all incoming
traffic on eth0, and leave the policy of whether traffic for a given IP
should be delivered to the machine up to the load balancer.
Can be setup as follows:
ip -6 rule from all iif eth0 lookup 200
ip -6 route add local default dev lo table 200
(in this case for all IPv6 addresses)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 and IPv6 have separate neighbour tables, so
the warning messages should be distinguishable.
[ Add a suitable message prefix on the ipv4 side as well -DaveM ]
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl output ipv6 gc_elasticity and min_adv_mss as values divided by
HZ. However, they are not in unit of jiffies, since ip6_rt_min_advmss
refers to packet size and ip6_rt_fc_elasticity is used as scaler as in
expire>>ip6_rt_gc_elasticity, so replace the jiffies conversion
handler will regular handler for them.
This has impact on scripts that are currently working assuming the
divide by HZ, will yield different results with this patch in place.
Signed-off-by: Min Zhang <mzhang@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RCU to avoid atomic ops on idev refcnt in ipv6_get_mtu()
and ip6_dst_hoplimit()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f4f914b5 (net: ipv6 bind to device issue) caused
a regression with Mobile IPv6 when it changed the meaning
of fl->oif to become a strict requirement of the route
lookup. Instead, only force strict mode when
sk->sk_bound_dev_if is set on the calling socket, getting
the intended behavior and fixing the regression.
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from net/ (but not any netfilter files)
all the unnecessary return; statements that precede the
last closing brace of void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue raises when having 2 NICs both assigned the same
IPv6 global address.
If a sender binds to a particular NIC (SO_BINDTODEVICE),
the outgoing traffic is being sent via the first found.
The bonded device is thus not taken into an account during the
routing.
From the ip6_route_output function:
If the binding address is multicast, linklocal or loopback,
the RT6_LOOKUP_F_IFACE bit is set, but not for global address.
So binding global address will neglect SO_BINDTODEVICE-binded device,
because the fib6_rule_lookup function path won't check for the
flowi::oif field and take first route that fits.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Scott Otto <scott.otto@alcatel-lucent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This is ipv6 variant of the commit 5e016cbf6.. ("ipv4: Don't drop
redirected route cache entry unless PTMU actually expired")
by Guenter Roeck <guenter.roeck@ericsson.com>.
Remove cache route entry in ipv6_negative_advice() only if
the timer is expired.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the only path leading to ip6_dst_check makes an indirect call
through dst->ops, dst cannot be NULL in ip6_dst_check.
This patch removes this check in case it misleads people who
come across this code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPV6_PREFER_SRC_xxx definitions:
| #define IPV6_PREFER_SRC_TMP 0x0001
| #define IPV6_PREFER_SRC_PUBLIC 0x0002
| #define IPV6_PREFER_SRC_COA 0x0004
RT6_LOOKUP_F_xxx definitions:
| #define RT6_LOOKUP_F_SRCPREF_TMP 0x00000008
| #define RT6_LOOKUP_F_SRCPREF_PUBLIC 0x00000010
| #define RT6_LOOKUP_F_SRCPREF_COA 0x00000020
So, we can translate between these two groups by shift operation
instead of multiple 'if's.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4291 section 2.4 states that all uncategorized addresses
should be considered as Global Unicast.
This will remove IPV6_ADDR_RESERVED completely
and return IPV6_ADDR_UNICAST in ipv6_addr_type() instead.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dunno, what was the idea, it wasn't used for a long time.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__net_init/__net_exit are apparently not going away, so use them
to full extent.
In some cases __net_init was removed, because it was called from
__net_exit code.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl table was copied, all right, but ->data for net.ipv6.route.gc_min_interval_ms
was not reinitialized for "!= &init_net" case.
In init_net everthing works by accident due to correct ->data initialization
in source table.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
Now that sys_sysctl is a compatiblity wrapper around /proc/sys
all sysctl strategy routines, and all ctl_name and strategy
entries in the sysctl tables are unused, and can be
revmoed.
In addition neigh_sysctl_register has been modified to no longer
take a strategy argument and it's callers have been modified not
to pass one.
Cc: "David Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Change ip6_route_redirect() to use ipv6_addr_copy().
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused.
It isn't needed -- read or write flag is already passed and sysctl
shouldn't care about the rest.
It _was_ used in two places at arch/frv for some reason.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RFC4191 says that "If the Reserved (10) value is received, the Route
Information Option MUST be ignored.", so this patch makes us conform
to the RFC. This is different to the usage of the Default Router
Preference, where an invalid value must indeed be treated as
PREF_MEDIUM.
Signed-off-by: Jens Rosenboom <me@jayr.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct net::ipv6.ip6_dst_ops is separatedly dynamically allocated,
but there is no fundamental reason for it. Embed it directly into
struct netns_ipv6.
For that:
* move struct dst_ops into separate header to fix circular dependencies
I honestly tried not to, it's pretty impossible to do other way
* drop dynamical allocation, allocate together with netns
For a change, remove struct dst_ops::dst_net, it's deducible
by using container_of() given dst_ops pointer.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all the code that deals directly with ICMPv6 type and code
values to use u8 instead of a signed int as that's the actual data
type.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of unspecified protocol in IPv6 initial route prevents quagga to
install IPv6 default route:
# show ipv6 route
S ::/0 [1/0] via fe80::1, eth1_0
K>* ::/0 is directly connected, lo, rej
C>* ::1/128 is directly connected, lo
C>* fe80::/64 is directly connected, eth1_0
# ip -6 route
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
ff00::/8 dev eth1_0 metric 256 mtu 1500 advmss 1440 hoplimit -1
unreachable default dev lo proto none metric -1 error -101 hoplimit 255
The attached patch ensures RTPROT_KERNEL to the default initial route
and fixes the problem for quagga.
This is similar to "ipv6: protocol for address routes"
f410a1fba7.
# show ipv6 route
S>* ::/0 [1/0] via fe80::1, eth1_0
C>* ::1/128 is directly connected, lo
C>* fe80::/64 is directly connected, eth1_0
# ip -6 route
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
ff00::/8 dev eth1_0 metric 256 mtu 1500 advmss 1440 hoplimit -1
default via fe80::1 dev eth1_0 proto zebra metric 1024 mtu 1500
advmss 1440 hoplimit -1
unreachable default dev lo proto kernel metric -1 error -101 hoplimit 255
Signed-off-by: Jean-Mickael Guerin <jean-mickael.guerin@6wind.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return value of nlmsg_notify() as follows:
If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.
This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.
This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the IPv6 multicast routing issues described
below. It was tested with XORP 1.4/1.5 as the IPv6 PIM-SM routing
daemon against FreeBSD peers.
net/ipv6/ip6_input.c:
- Don't try to forward link-local multicast packets.
- Don't reset skb2->dev before calling ip6_mr_input() so packets can
be identified as coming from the PIM register vif properly.
net/ipv6/ip6mr.c:
- Fix incoming PIM register messages processing:
* The IPv6 pseudo-header should be included when checksumming PIM
messages (RFC 4601 section 4.9; RFC 3973 section 4.7.1).
* Packets decapsulated from PIM register messages should have
skb->protocol ETH_P_IPV6.
- Enable/disable IPv6 multicast forwarding on the corresponding
interface when a routing daemon adds/removes a multicast virtual
interface.
- Remove incorrect skb_pull() to fix userspace signaling.
- Enable/disable global IPv6 multicast forwarding when an IPv6
multicast routing socket is opened/closed.
net/ipv6/route.c:
- Don't use strict routing logic for packets decapsulated from PIM
register messages (similar to disabling rp_filter for the IPv4
case).
Signed-off-by: Thomas Goff <thomas.goff@boeing.com>
Reviewed-by: Fred Templin <fred.l.templin@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to excellent diagnosis by Eduard Guzovsky.
The core problem is that on a network with lots of active
multicast traffic, the neighbour cache can fill up. If
we try to allocate a new route and thus neighbour cache
entry, the bog-standard GC attempt the neighbour layer does
in ineffective because route entries hold a reference
to the existing neighbour entries and GC can only liberate
entries with no references.
IPV4 already has a way to handle this, by doing a route cache
GC in such situations (when neigh attach returns -ENOBUFS).
So simply mimick this on the ipv6 side.
Tested-by: Eduard Guzovsky <eguzovsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This last patch makes the appropriate changes to use and propagate the
network namespace where needed in IPv6 multicast forwarding code.
This consists mainly in replacing all the remaining init_net occurences
with current netns pointer retrieved from sockets, net devices or
mfc6_caches depending on the routines' contexts.
Some routines receive a new 'struct net' parameter to propagate the current
netns:
* ip6mr_get_route
* ip6mr_cache_report
* ip6mr_cache_find
* ip6mr_cache_unresolved
* mif6_add/mif6_delete
* ip6mr_mfc_add/ip6mr_mfc_delete
* ip6mr_reg_vif
All the IPv6 multicast forwarding variables moved to struct netns_ipv6 by
the previous patches are now referenced in the correct namespace.
Changelog:
==========
* Take into account the net associated to mfc6_cache when matching entries in
mfc_unres_queue list.
* Call mroute_clean_tables() in ip6mr_net_exit() to free memory allocated
per-namespace.
* Call dev_net_set() in ip6mr_reg_vif() to initialize dev->nd_net
correctly.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warns when using the # modifier with the %p format specifier,
so we can't use this to omit the colons when needed, introduces
%pi6 instead.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The define in kernel.h can be done away with at a later time.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes that ip6_route_net_init() does all of the route init code.
There used to be a race between ip6_route_net_init() and ip6_net_init()
and someone relying on the combined result was left out cold.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_net_init() error handling looked less than solid, fix 'er up.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg reported that occaisionally, bringing an interface
down or unregistering it would hang for up to 30 seconds. Using
debugging output he provided it became clear that ICMP6 routes
were the culprit.
The problem is that ICMP6 routes live in their own world totally
separate from normal ipv6 routes. So there are all kinds of special
cases throughout the ipv6 code to handle this.
While we should really try to unify all of this stuff somehow,
for the time being let's fix this by purging the ICMP6 routes
that match the device in question during rt6_ifdown().
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_dev_get_saddr() blindly de-references dst_dev to get the network
namespace, but some callers might pass NULL. Change callers to pass a
namespace pointer instead.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan wrote:
> On Thu, Aug 07, 2008 at 07:00:56PM +0200, John Gumb wrote:
>> Scenario: no ipv6 default route set.
>
>> # ip -f inet6 route get fec0::1
>>
>> BUG: unable to handle kernel NULL pointer dereference at 00000000
>> IP: [<c0369b85>] rt6_fill_node+0x175/0x3b0
>> EIP is at rt6_fill_node+0x175/0x3b0
>
> 0xffffffff80424dd3 is in rt6_fill_node (net/ipv6/route.c:2191).
> 2186 } else
> 2187 #endif
> 2188 NLA_PUT_U32(skb, RTA_IIF, iif);
> 2189 } else if (dst) {
> 2190 struct in6_addr saddr_buf;
> 2191 ====> if (ipv6_dev_get_saddr(ip6_dst_idev(&rt->u.dst)->dev,
> ^^^^^^^^^^^^^^^^^^^^^^^^
> NULL
>
> 2192 dst, 0, &saddr_buf) == 0)
> 2193 NLA_PUT(skb, RTA_PREFSRC, 16, &saddr_buf);
> 2194 }
The commit that changed this can't be reverted easily, but the patch
below works for me.
Fix NULL de-reference in rt6_fill_node() when there's no IPv6 input
device present in the dst entry.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dst_metric() with dst_mtu() in net/ipv6/route.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change icmp6_dst_gc to return the one value the caller cares about rather
than using call by reference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are already 7 of them - time to kill some duplicate code.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Outgoing interface is selected by the route decision if unspecified.
Let's prefer routes via interface(s) with the address assigned if we
have multiple routes with same cost.
With help from Naohiro Ooiwa <nooiwa@miraclelinux.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Handle interface property strictly when looking up a route
for the loopback address (RFC4291 2.5.3).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
The commit 77d16f450a ("[IPV6] ROUTE:
Unify RT6_F_xxx and RT6_SELECT_F_xxx flags") intended to pass various
routing lookup hints around RT6_LOOKUP_F_xxx flags, but conversion was
missing for rt6_device_match().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) We may have route lifetime larger than INT_MAX.
In that case we had wired value in lifetime.
Use INT_MAX if lifetime does not fit in s32.
2) Lifetime is valid iif RTF_EXPIRES is set.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
- Allow longer lifetimes (>= 0x7fffffff/HZ) on 64bit archs
by using unsigned long.
- Shadow this arithmetic overflow workaround by introducing
helper functions: addrconf_timeout_fixup() and
addrconf_finite_timeout().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Because the IPsec output function xfrm_output_resume does its
own dst_output call it should always call __ip_local_output
instead of ip_local_output as the latter may invoke dst_output
directly. Otherwise the return values from nf_hook and dst_output
may clash as they both use the value 1 but for different purposes.
When that clash occurs this can cause a packet to be used after
it has been freed which usually leads to a crash. Because the
offending value is only returned from dst_output with qdiscs
such as HTB, this bug is normally not visible.
Thanks to Marco Berizzi for his perseverance in tracking this
down.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to handle infinite prefix lifetime specially.
With help from original reporter "Bonitch, Joseph"
<Joseph.Bonitch@xerox.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We could not see appropriate lifetime if the route had been scheduled
to expired at 0 (in jiffies). We should check rt6i_flags instead of
rt6i_expires to determine whether lifetime is valid or not.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of arithmetic overflow avoidance, the actual lifetime setting
(vs the value given by RA) did not increase monotonically around
0x7fffffff/HZ.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are functions to refer to the value of dst->metric[THE_METRIC-1]
directly without use of a inline function "dst_metric" defined in
net/dst.h.
The following patch changes them to use the inline function
consistently.
Signed-off-by: Satoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_route_net_init() performs some unneeded actions.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the needlessly global struct
ip6_prohibit_entry_template static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the Linux the Intra-Site Automatic Tunnel Addressing
Protocol (ISATAP) implementation. It places the ISATAP potential router
list (PRL) in the kernel and adds three new private ioctls for PRL
management.
[Add several changes of structure name, constant names etc. - yoshfuji]
Signed-off-by: Fred L. Templin <fred.l.templin@boeing.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
The commits f3db4851 ([NETNS][IPV6] ip6_fib - fib6_clean_all handle several
network namespaces) and 69ddb805 ([NETNS][IPV6] route6 - Make proc entry
/proc/net/rt6_stats per namespace) made some proc files per net.
Both of them introduced potential OOPS - get_proc_net can return NULL, but
this check is lost - and a struct net leak - in case single_open() fails the
previously got net is not put.
Kill all these bugs with one patch.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce per-sock inlines: sock_net(), sock_net_set()
and per-inet_timewait_sock inlines: twsk_net(), twsk_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Last part of hop-limit determination is always:
hoplimit = dst_metric(dst, RTAX_HOPLIMIT);
if (hoplimit < 0)
hoplimit = ipv6_get_hoplimit(dst->dev).
Let's consolidate it as ip6_dst_hoplimit(dst).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an netns parameter to ip6_route_output. That will allow to access
to the right routing table for outgoing traffic.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches improves the readibility of the ip6_dst_gc() routine.
It simplifies long lines which grow a lot due to the introduction
of network namespaces support.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the necessary changes to make IPv6 dst_entry garbage
collection work with multiple network namespaces.
In ip6_dst_gc(), static local variables are now declared
per-namespace.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6_dst_ops is moved inside the network namespace structure. All
references to this structure are now relative to the initial network
namespace.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_dst_ops is dynamically allocated in init and exit functions. That
provides the ability to do multiple instanciations of this structure.
This will be needed for network namespaces, indeed dst_ops stores data
that are required to be per namespace: entries and gc_thresh.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rt6_info structures are moved inside the network namespace
structure. All references to these structures are now relative to the
initial network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch make mindless changes and prepares the code to use dynamic
allocation for rt6_info structure. The code accesses the rt6_info
structure as a pointer instead of a global static variable.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the routing engine use the network namespaces to
access routing informations: Add a network namespace parameter to
ipv6_route_ioctl and propagate the network namespace value to all the
routing code that have not yet been changed.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a network namespace parameter to rt6_purge_dflt_routers. This is
needed to call fib6_get_table with the appropriate network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a network namespace parameter to rt6_add_route_info() and
rt6_get_route_info to enable them to handle multiple network
namespaces.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the proc entry /proc/net/rt6_stats work in all network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a network namespace parameter to rt6_lookup().
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make /proc/net/ipv6_route and /proc/net/rt6_stats to be per namespace.
These proc files are now created when the network namespace is
initialized.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rt6_stats is now per namespace with this patch. It is allocated
when a network namespace is created and freed when the network
namespace exits and references are relative to the network namespace.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allocates the rt6_stats struct dynamically when the fib6 is
initialized. That provides the ability to create several instances of
this structure for the network namespaces.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the timer initialization at the network namespace creation and
store the network namespace in the timer argument.
That enables multiple timers (one per network namespace) to do garbage
collecting.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib tables are now relative to the network namespace. When the
garbage collector timer expires, we must have a network namespace
parameter in order to retrieve the tables. For now this is the
init_net, but we should be able to have a timer per namespace and use
the timer callback parameter to pass the network namespace from the
expired timer.
The timer callback, fib6_run_gc, is actually used to be called
synchronously by some functions and asynchronously when the timer
expires.
When the timer expires, the delay specified for fib6_run_gc parameter
is always zero. So, I changed fib6_run_gc to not be a timer callback
but a function called by the timer callback and I added a timer
callback where its work is just to retrieve from the data arg of the
timer the network namespace and call fib6_run_gc with zero expiring
time and the network namespace parameters. That makes the code cleaner
for the fib6_run_gc callers.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function fib6_clean_all takes the network namespace as
parameter. That allows to flush the routes related to a specific
network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib table for ipv6 are moved to the network namespace structure.
All references to them are made relatively to the network namespace.
All external calls to the ip6_fib functions taking the network
namespace parameter are made using the init_net variable, so the
ip6_fib engine is ready for the namespaces but the callers not yet.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For later use, this patch is renaming ndisc_dst_alloc()
(and related function/structures) to icmp6_dst_alloc()
(and so on). This patch also removing unused function-
pointer argument for it.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Since most users of ipv6_get_saddr() pass non-NULL as
dst argument, use ipv6_dev_get_saddr() directly.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Add some more missing initializations of the new nl_info.nl_net field
in IPv6 stack. This field will be used when network namespaces are
fully supported.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the explicit usage of the magic constant "1024"
with IP6_RT_PRIO_USER in the IPV6 tree.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed because in ndisc.c, we have:
static void ndisc_router_discovery(struct sk_buff *skb)
{
// ...
if (ndopts.nd_opts_mtu) {
// ...
if (rt)
rt->u.dst.metrics[RTAX_MTU-1] = mtu;
rt6_mtu_change(skb->dev, mtu);
// ...
}
Since the mtu is set directly here, rt6_mtu_change_route thinks that
it is unchanged, and so it fails to update the MSS accordingly. This
patch lets rt6_mtu_change_route still update MSS if old_mtu == new_mtu.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All but one struct dst_ops static initializations miss explicit
initialization of entries field.
As this field is atomic_t, we should use ATOMIC_INIT(0), and not
rely on atomic_t implementation.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing initialization of the new nl_info.nl_net field in
rtm_to_fib6_config(). This will be needed the store network namespace
associated to the fib6_config struct.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The garbage collection function receive the dst_ops structure as
parameter. This is useful for the next incoming patchset because it
will need the dst_ops (there will be several instances) and the
network namespace pointer (contained in the dst_ops).
The protocols which do not take care of the namespaces will not be
impacted by this change (expect for the function signature), they do
just ignore the parameter.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nl_info is used to track the end-user destination of routing change
notification. This is a natural object to hold a namespace on. Place
it there and utilize the context in the appropriate places.
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the sysctl concerning the routes are moved to the network
namespace structure. A helper function is called to initialize the
variables.
Because the ipv6 protocol is not yet per namespace, the variables are
accessed relatively from the network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each network namespace wants its own set of sysctl value, eg. we
should not be able from a namespace to set a sysctl value for another
namespace , especially for the initial network namespace.
This patch duplicates the sysctl table when we register a new network
namespace for ipv6. The duplicated table are postfixed with the
"template" word to notify the developper the table is cloned.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the code in the inet6_rt_notify more straightforward and provides
groud for namespace passing.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch defines the usual static inline functions when the code is
disabled for fib6_rules. That's allow to remove some ifdef in route.c
file and make the code a little more clear.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch create the usual static inline functions to disable
the xfrm6_init and xfrm6_fini function when XFRM is off.
That's allow to remove some ifdef and make the code a little more clear.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the proc creation/destruction to be a separate function. That
allows to remove the #ifdef CONFIG_PROC_FS in the init/fini function
and make them more readable.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the kmem_cache_creation fails, the kernel will panic. It is
acceptable if the system is booting, but if the ipv6 protocol is
compiled as a module and it is loaded after the system has booted, do
we want to panic instead of just failing to initialize the protocol ?
The init function is now returning an error and this one is checked
for protocol initialization. So the ipv6 protocol will safely fails.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The route initialization function does not return any value to notify
if the initialization is successful or not. This patch checks all
calls made for the initilization in order to return a value for the
caller.
Unfortunately, proc_net_fops_create will return a NULL pointer if
CONFIG_PROC_FS is off, so we can not check the return code without an
ifdef CONFIG_PROC_FS block in the ip6_route_init function.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move dst entries to a namespace loopback to catch refcounting leaks.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes support for the Intra-Site Automatic Tunnel
Addressing Protocol (ISATAP) per RFC4214. It uses the SIT
module, and is configured using extensions to the "iproute2"
utility. The diffs are specific to the Linux 2.6.24-rc2 kernel
distribution.
This version includes the diff for ./include/linux/if.h which was
missing in the v2.4 submission and is needed to make the
patch compile. The patch has been installed, compiled and
tested in a clean 2.6.24-rc2 kernel build area.
Signed-off-by: Fred L. Templin <fred.l.templin@boeing.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this patch none of the netlink callback support anything
except the initial network namespace but the rtnetlink infrastructure
now handles multiple network namespaces.
Changes from v2:
- IPv6 addrlabel processing
Changes from v1:
- no need for special rtnl_unlock handling
- fixed IPv6 ndisc
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before I can enable rtnetlink to work in all network namespaces I need
to be certain that something won't break. So this patch deliberately
disables all of the rtnletlink methods in everything except the
initial network namespace. After the methods have been audited this
extra check can be disabled.
Changes from v1:
- added IPv6 addrlabel protection
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As part of the work on asynchrnous cryptographic operations, we need
to be able to resume from the spot where they occur. As such, it
helps if we isolate them to one spot.
This patch moves most of the remaining family-specific processing into
the common output code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a number of copies of dst_discard scattered around the place
which all do the same thing, namely free a packet on the input or
output paths.
This patch deletes all of them except dst_discard and points all the
users to it.
The only non-trivial bit is decnet where it returns an error.
However, conceptually this is identical to the blackhole functions
used in IPv4 and IPv6 which do not return errors. So they should
either all return errors or all return zero. For now I've stuck with
the majority and picked zero as the return value.
It doesn't really matter in practice since few if any driver would
react differently depending on a zero return value or NET_RX_DROP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We omit (or delay) sending NSes for known-to-unreachable routers (in
NUD_FAILED state) according to RFC 4191 (Default Router Preferences
and More-Specific Routes). But this is not fully compatible with RFC
4861 (Neighbor Discovery Protocol for IPv6), which does not remember
unreachability of neighbors.
So, let's avoid mixing sending algorithm of RFC 4191 and that of RFC
4861, and make the algorithm more friendly with RFC 4861 if RFC 4191
is disabled.
Issue was found by IPv6 Ready Logo Core Self_Test 1.5.0b2 (by TAHI
Project), and has been tracked down by Mitsuru Chinen
<mitch@linux.vnet.ibm.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many places that get the dst entry, increase the
__use counter and set the "lastuse" time stamp.
Make a helper for this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes last proc_net_create() user. Kudos to Benjamin Thery and
Stephen Hemminger for comments on previous version.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't preoperly support the sysctl binary path for flushing the ipv6
routes. So remove support for a binary path.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The difference in both functions is in the "id" passed to
the rt6_select, so just pass it as an extra argument from
two outer helpers.
This is minus 60 lines of code and 360 bytes of .text
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes loopback_dev per network namespace. Adding
code to create a different loopback device for each network
namespace and adding the code to free a loopback device
when a network namespace exits.
This patch modifies all users the loopback_dev so they
access it as init_net.loopback_dev, keeping all of the
code compiling and working. A later pass will be needed to
update the users to use something other than the initial network
namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all occurences to the static variable
loopback_dev to a pointer loopback_dev. That provides the
mindless, trivial, uninteressting change part for the dynamic
allocation for the loopback.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: Kirill Korotaev <dev@sw.ru>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows the generic attribute interface to be used within
the netfilter subsystem where this flag was initially introduced.
The byte-order flag is yet unused, it's intended use is to
allow automatic byte order convertions for all atomic types.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes /proc/net per network namespace. It modifies the global
variables proc_net and proc_net_stat to be per network namespace.
The proc_net file helpers are modified to take a network namespace argument,
and all of their callers are fixed to pass &init_net for that argument.
This ensures that all of the /proc/net files are only visible and
usable in the initial network namespace until the code behind them
has been updated to be handle multiple network namespaces.
Making /proc/net per namespace is necessary as at least some files
in /proc/net depend upon the set of network devices which is per
network namespace, and even more files in /proc/net have contents
that are relevant to a single network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADVMSS value was incorrectly updated for ALL routes when the MTU
is updated because it's outside the effect of the if statement's
condition.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current IPSEC rule resolution behavior we have does not work for a
lot of people, even though technically it's an improvement from the
-EAGAIN buisness we had before.
Right now we'll block until the key manager resolves the route. That
works for simple cases, but many folks would rather packets get
silently dropped until the key manager resolves the IPSEC rules.
We can't tell these folks to "set the socket non-blocking" because
they don't have control over the non-block setting of things like the
sockets used to resolve DNS deep inside of the resolver libraries in
libc.
With that in mind I coded up the patch below with some help from
Herbert Xu which provides packet-drop behavior during larval state
resolution, controllable via sysctl and off by default.
This lays the framework to either:
1) Make this default at some point or...
2) Move this logic into xfrm{4,6}_policy.c and implement the
ARP-like resolution queue we've all been dreaming of.
The idea would be to queue packets to the policy, then
once the larval state is resolved by the key manager we
re-resolve the route and push the packets out. The
packets would timeout if the rule didn't get resolved
in a certain amount of time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Spring cleaning time...
There seems to be a lot of places in the network code that have
extra bogus semicolons after conditionals. Most commonly is a
bogus semicolon after: switch() { }
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the skb->nh union has just one member, .raw, i.e. it is just like the
skb->mac union, strange, no? I'm just leaving it like that till the transport
layer is done with, when we'll rename skb->mac.raw to skb->mac_header (or
->mac_header_offset?), ditto for ->{h,nh}.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet which is being discarded because of no routes in the
forwarding path should not be counted as OutNoRoutes but as
InNoRoutes.
Additionally, on this occasion, a packet whose destinaion is
not valid should be counted as InAddrErrors separately.
Based on patch from Mitsuru Chinen <mitch@linux.vnet.ibm.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per RFC2461, section 6.3.6, item #2, when no routers on the
matching list are known to be reachable or probably reachable we
do round robin on those available routes so that we make sure
to probe as many of them as possible to detect when one becomes
reachable faster.
Each routing table has a rwlock protecting the tree and the linked
list of routes at each leaf. The round robin code executes during
lookup and thus with the rwlock taken as a reader. A small local
spinlock tries to provide protection but this does not work at all
for two reasons:
1) The round-robin list manipulation, as coded, goes like this (with
read lock held):
walk routes finding head and tail
spin_lock();
rotate list using head and tail
spin_unlock();
While one thread is rotating the list, another thread can
end up with stale values of head and tail and then proceed
to corrupt the list when it gets the lock. This ends up causing
the OOPS in fib6_add() later onthat many people have been hitting.
2) All the other code paths that run with the rwlock held as
a reader do not expect the list to change on them, they
expect it to remain completely fixed while they hold the
lock in that way.
So, simply stated, it is impossible to implement this correctly using
a manipulation of the list without violating the rwlock locking
semantics.
Reimplement using a per-fib6_node round-robin pointer. This way we
don't need to manipulate the list at all, and since the round-robin
pointer can only ever point to real existing entries we don't need
to perform any locking on the changing of the round-robin pointer
itself. We only need to reset the round-robin pointer to NULL when
the entry it is pointing to is removed.
The idea is from Thomas Graf and it is very similar to how this
was implemented before the advanced router selection code when in.
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning up the warnings on gcc makes it emit warnings
about the placement of 'inline' in function declarations.
Here's everything that was under net/
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the next pointer from 'struct rt6_info.u' union,
and renames u.next to u.dst.rt6_next.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
