Florian Fainelli says:
====================
net: dsa: mv88e6xxx: fix IPv6
We have had some emails in private over this issue, this is my current
patch set rebased on top of net-next which provides working IPv6 (and
probably other protocols as well) over mv88e6xxx DSA switches.
The problem comes down to mv88e6xxx defaulting to not flood unknown
unicast and multicast datagrams, as they would be by dumb switches,
and as the Linux bridge code does by default.
There is also the issue of IPv6 over a vlan that is transparent to the
bridge; the multicast querier will not reach inside the vlan, and so
the switch can not learn about multicast routing within the vlan.
These flood settings can be disabled via the Linux bridge code if it's
desired to make the switch behave more like a managed switch, eg, by
enabling the multicast querier. However, the multicast querier
defaults to being disabled which effectively means that by default,
mv88e6xxx switches block all multicast traffic. This is at odds with
the Linux bridge documentation, and the defaults that the Linux bridge
code adopts.
So, this patch set adds DSA support for Linux bridge flags, adds
mv88e6xxx support for the unicast and multicast flooding flags, and
lastly enables flooding of these frames by default to match the
Linux bridge defaults.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches work by learning the MAC address for each attached station by
monitoring traffic from each station. When a station sends a packet,
the switch records which port the MAC address is connected to.
With IPv4 networking, before communication commences with a neighbour,
an ARP packet is broadcasted to all stations asking for the MAC address
corresponding with the IPv4. The desired station responds with an ARP
reply, and the ARP reply causes the switch to learn which port the
station is connected to.
With IPv6 networking, the situation is rather different. Rather than
broadcasting ARP packets, a "neighbour solicitation" is multicasted
rather than broadcasted. This multicast needs to reach the intended
station in order for the neighbour to be discovered.
Once a neighbour has been discovered, and entered into the sending
stations neighbour cache, communication can restart at a point later
without sending a new neighbour solicitation, even if the entry in
the neighbour cache is marked as stale. This can be after the MAC
address has expired from the forwarding cache of the DSA switch -
when that occurs, there is a long pause in communication.
Our DSA implementation for mv88e6xxx switches disables flooding of
multicast and unicast frames for bridged ports. As per the above
description, this is fine for IPv4 networking, since the broadcasted
ARP queries will be sent to and received by all stations on the same
network. However, this breaks IPv6 very badly - blocking neighbour
solicitations and later causing connections to stall.
The defaults that the Linux bridge code expect from bridges are for
unknown unicast and unknown multicast frames to be flooded to all ports
on the bridge, which is at odds to the defaults adopted by our DSA
implementation for mv88e6xxx switches.
This commit enables by default flooding of both unknown unicast and
unknown multicast frames whenever a port is added to a bridge, and
disables the flooding when a port leaves the bridge. This means that
mv88e6xxx DSA switches now behave as per the bridge(8) man page, and
IPv6 works flawlessly through such a switch.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the bridge flags to Marvell 88e6xxx bridges, allowing
the multicast and unicast flood properties to be controlled. These
can be controlled on a per-port basis via commands such as:
bridge link set dev lan1 flood on|off
bridge link set dev lan1 mcast_flood on|off
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux bridge implementation allows various properties of the bridge
to be controlled, such as flooding unknown unicast and multicast frames.
This patch adds the necessary DSA infrastructure to allow the Linux
bridge support to control these properties for DSA switches.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[florian: Add missing dp and ds variables declaration to fix build]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_ip4_multicast_mrd_rcv only return 0 and -ENOMSG,
no other negative value
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This case block has been terminated by a return, so not need
a switch fall-through
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error code isn't set on this path so it would result in returning
ERR_PTR(0) and a NULL dereference in the caller.
Fixes: 18d3eefb17 ("net: sched: refactor tcf_block_find() into standalone functions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are spelling mistakes in warning macro messages. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the only way to clear the forwarding cache was to delete the
entries one by one using the MRT_DEL_MFC socket option or to destroy and
recreate the socket.
Create a new socket option which with the use of optional flags can
clear any combination of multicast entries (static or not static) and
multicast vifs (static or not static).
Calling the new socket option MRT_FLUSH with the flags MRT_FLUSH_MFC and
MRT_FLUSH_VIFS will clear all entries and vifs on the socket except for
static entries.
Signed-off-by: Callum Sinclair <callum.sinclair@alliedtelesis.co.nz>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_check_and_restart_aneg() to reduce
boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used by config_aneg callback implementations of
PHY drivers and allows to reduce boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in genphy_config_aneg() for clause 22 PHY's, we should keep modes
from being advertised that are known to be broken with EEE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: improve genphy_read_status
Series includes two smaller improvements to genphy_read_status.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If link partner and we can't agree on any mode, then it doesn't make
sense to pretend we would have agreed on 10/half. Therefore set a
proper default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes to genphy_read_status() this orphaned register
read remained as leftover. So remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read port count from the shared memory instead of driver deriving this
value. This change simplifies the driver implementation and also avoids
any dependencies for finding the port-count.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha says:
====================
Devlink health fixes series
This series includes two small fixes from Aya for the devlink health
infrastructure introduced earlier in this window.
First patch rename some UAPI attributes to better reflect their use.
Second patch reduces the amount of data passed from the devlink to the
netlink layer upon get reporter command, in case of no-recovery reporter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid sending attributes related to recovery:
DEVLINK_ATTR_HEALTH_REPORTER_GRACEFUL_PERIOD and
DEVLINK_ATTR_HEALTH_REPORTER_AUTO_RECOVER in reply to
DEVLINK_CMD_HEALTH_REPORTER_GET for a reporter which didn't register a
recover operation.
These parameters can't be configured on a reporter that did not provide
a recover operation, thus not needed to return them.
Fixes: 7afe335a8b ("devlink: Add health get command")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename devlink health attributes for better reflect the attributes use.
Add COUNT prefix on error counter attribute and recovery counter
attribute.
Fixes: 7afe335a8b ("devlink: Add health get command")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: patches 2019-02-21
here are patches for SMC:
* patch 1 is a cleanup without functional change
* patches 2-6 enhance SMC pnetid support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC-D devices are identified by their PCI IDs in the pnet table. In
order to make usage of the pnet table more consistent for users, this
patch adds this form of identification for ib devices as well.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds namespace support to the pnet table code. Each network
namespace gets its own pnet table. Infiniband and smcd device pnetids
can only be modified in the initial namespace. In other namespaces they
can still be used as if they were set by the underlying hardware.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, users can only set pnetids for netdevs and ib devices in the
pnet table. This patch adds support for smcd devices to the pnet table.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a device does not have a pnetid, users can set a temporary pnetid for
said device in the pnet table. This patch reworks the pnet table to make
it more flexible. Multiple entries with the same pnetid but differing
devices are now allowed. Additionally, the netlink interface now sends
each mapping from pnetid to device separately to the user while
maintaining the message format existing applications might expect. Also,
the SMC data structure for ib devices already has a pnetid attribute.
So, it is used to store the user defined pnetids. As a result, the pnet
table entries are only used for netdevs.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pnetids are retrieved from the underlying hardware as EBCDIC. This patch
converts pnetids to ASCII.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use local variable pflags from the beginning of function
smcr_tx_sndbuf_nonempty
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are rare cases where a PL_INT_CAUSE bit may end up getting
set when the corresponding PL_INT_ENABLE bit isn't set.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: disable aneg in genphy_c45_pma_setup_forced
When genphy_c45_pma_setup_forced() is called the "aneg enabled" bit
may still be set, therefore clear it. This is also in line with what
genphy_setup_forced() does for Clause 22.
v2:
- fix a typo in patch 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genphy_c45_pma_setup_forced() makes sure the "aneg enabled"
bit is cleared, the call to genphy_c45_an_disable_aneg() isn't needed
any longer. And the code pattern is now the same as in
genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When genphy_c45_pma_setup_forced() is called the "aneg enabled" bit may
still be set, therefore clear it. This is also in line with what
genphy_setup_forced() does for Clause 22.
v2:
- fix typo
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes misc updates to mlx5 drivers and one ethtool update.
1) From Aya Levin:
- ethtool: Define 50Gbps per lane link modes
- add support for 50Gbps per lane link modes in mlx5 driver
2) From Tariq Toukan,
- Add a helper function to unify mlx5 resource reloading
3) From Vlad Buslov,
- Remove wrong and superfluous tc pedit header type check
4) From Tonghao Zhang,
- Some refactoring in en_tc.c to simplify the mlx5e_tc_add_fdb_flow
5) From Leon Romanovsky & Saeed,
- Compilation warning fixes
6) From Bodong wang,
- E-Switch fixes that are related to the SmarNIC series
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcbH/oAAoJEEg/ir3gV/o+bJQIAKIbILkQsAIn3B3U1Y7WgE8l
4pXdcYe6A3Mr9ZOi+U2ovJqVEHKPc7ASNfBfK5zsRayxhDQmoNhaloZSlwkgxenN
+guf86OBqTmXq9vzk3AFfPbiceQ+ENkM8ZHsv0yc9q8ZgZX5KR3ghG0j7wONDdgv
UOGuHNbO2QPA2d38V+xdwGkr/M8eep2xjYwDqT8+s7F+7BZeRThF2s9NBhE4rgob
KlPXwYTqkx5fiODtlFE9igryi/aSr9iaVIVCOs9ZBwQrETc/WLttWbfMgrMWFW5z
r4sa/84oVe0GVwZ+KPJKjUpXR4x1C3O+vSIAREsZfBDfjADHvGgXyRCYw+xrnq4=
=9kOH
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-02-19' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-02-19
This series includes misc updates to mlx5 drivers and one ethtool update.
1) From Aya Levin:
- ethtool: Define 50Gbps per lane link modes
- add support for 50Gbps per lane link modes in mlx5 driver
2) From Tariq Toukan,
- Add a helper function to unify mlx5 resource reloading
3) From Vlad Buslov,
- Remove wrong and superfluous tc pedit header type check
4) From Tonghao Zhang,
- Some refactoring in en_tc.c to simplify the mlx5e_tc_add_fdb_flow
5) From Leon Romanovsky & Saeed,
- Compilation warning fixes
6) From Bodong wang,
- E-Switch fixes that are related to the SmarNIC series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 033b228e7f)
When tcindex_destroy() destroys all the filter results in
the perfect hash table, it invokes the walker to delete
each of them. However, results with class==0 are skipped
in either tcindex_walk() or tcindex_delete(), which causes
a memory leak reported by kmemleak.
This patch fixes it by skipping the walker and directly
deleting these filter results so we don't miss any filter
result.
As a result of this change, we have to initialize exts->net
properly in tcindex_alloc_perfect_hash(). For net-next, we
need to consider whether we should initialize ->net in
tcf_exts_init() instead, before that just directly test
CONFIG_NET_CLS_ACT=y.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 8015d93ebd)
tcindex_destroy() invokes tcindex_destroy_element() via
a walker to delete each filter result in its perfect hash
table, and tcindex_destroy_element() calls tcindex_delete()
which schedules tcf RCU works to do the final deletion work.
Unfortunately this races with the RCU callback
__tcindex_destroy(), which could lead to use-after-free as
reported by Adrian.
Fix this by migrating this RCU callback to tcf RCU work too,
as that workqueue is ordered, we will not have use-after-free.
Note, we don't need to hold netns refcnt because we don't call
tcf_exts_destroy() here.
Fixes: 27ce4f05e2 ("net_sched: use tcf_queue_work() in tcindex filter")
Reported-by: Adrian <bugs@abtelecom.ro>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 121d57af30 ("gso: validate gso_type in GSO handlers") added
gso_type validation to existing gso_segment callback functions, to
filter out illegal and potentially dangerous SKB_GSO_DODGY packets.
Convert tunnels that now call inet_gso_segment and ipv6_gso_segment
directly to have their own callbacks and extend validation to these.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test case 'control_msg' has been updated to peek non-data record and
then verify the type of record received. Subsequently, the same record
is retrieved without MSG_PEEK flag in recvmsg().
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix suspend and resume in mt76x0u USB driver, from Stanislaw
Gruszka.
2) Missing memory barriers in xsk, from Magnus Karlsson.
3) rhashtable fixes in mac80211 from Herbert Xu.
4) 32-bit MIPS eBPF JIT fixes from Paul Burton.
5) Fix for_each_netdev_feature() on big endian, from Hauke Mehrtens.
6) GSO validation fixes from Willem de Bruijn.
7) Endianness fix for dwmac4 timestamp handling, from Alexandre Torgue.
8) More strict checks in tcp_v4_err(), from Eric Dumazet.
9) af_alg_release should NULL out the sk after the sock_put(), from Mao
Wenan.
10) Missing unlock in mac80211 mesh error path, from Wei Yongjun.
11) Missing device put in hns driver, from Salil Mehta.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
sky2: Increase D3 delay again
vhost: correctly check the return value of translate_desc() in log_used()
net: netcp: Fix ethss driver probe issue
net: hns: Fixes the missing put_device in positive leg for roce reset
net: stmmac: Fix a race in EEE enable callback
qed: Fix iWARP syn packet mac address validation.
qed: Fix iWARP buffer size provided for syn packet processing.
r8152: Add support for MAC address pass through on RTL8153-BD
mac80211: mesh: fix missing unlock on error in table_path_del()
net/mlx4_en: fix spelling mistake: "quiting" -> "quitting"
net: crypto set sk to NULL when af_alg_release.
net: Do not allocate page fragments that are not skb aligned
mm: Use fixed constant in page_frag_alloc instead of size + 1
tcp: tcp_v4_err() should be more careful
tcp: clear icsk_backoff in tcp_write_queue_purge()
net: mv643xx_eth: disable clk on error path in mv643xx_eth_shared_probe()
qmi_wwan: apply SET_DTR quirk to Sierra WP7607
net: stmmac: handle endianness in dwmac4_get_timestamp
doc: Mention MSG_ZEROCOPY implementation for UDP
mlxsw: __mlxsw_sp_port_headroom_set(): Fix a use of local variable
...
Another platform requires even longer delay to make the device work
correctly after S3.
So increase the delay to 300ms.
BugLink: https://bugs.launchpad.net/bugs/1798921
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing the struct ptp_clock_info caps by parameter is passing over 130 bytes
of data by value on the stack. Optimize this by passing it by reference instead.
Also shinks the object code size:
Before:
text data bss dec hex filename
12596 2160 64 14820 39e4 drivers/ptp/ptp_qoriq.o
After:
text data bss dec hex filename
12567 2160 64 14791 39c7 drivers/ptp/ptp_qoriq.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling vport, relevant vport configurations will be cleaned
up. These cleanups should be done to the vports which had these configs
applied at vport enablement. As esw manager vport didn't have such
vport config applied, cleanup should not touch it.
Fixes: de9e6a8136c5 ("net/mlx5: E-Switch, Properly refer to host PF vport as other vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reported-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When eswitch gets vport data structure, the index should not be out
of the range of the vport array. Driver mistakenly used vport number
to check the range.
Fixes: 22b8ddc86bf4 ("net/mlx5: E-Switch, Assign a different position for uplink rep and vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
fpga_qpn was assigned but never used and compilation with W=1
produced the following warning:
drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c: In function _mlx5_fpga_event_:
drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c:320:6: warning:
variable _fpga_qpn_ set but not used [-Wunused-but-set-variable]
u32 fpga_qpn;
^~~~~~~~
Fixes: 98db16bab5 ("net/mlx5: FPGA, Handle QP error event")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Compilation with W=1 produces following warning:
drivers/net/ethernet/mellanox/mlx5/core/en/monitor_stats.c:69:6:
warning: no previous prototype for _mlx5e_monitor_counter_start_ [-Wmissing-prototypes]
void mlx5e_monitor_counter_start(struct mlx5e_priv *priv)
^~~~~~~~~~~~~~~~~~~~~~~~~~~
Avoid it by declaring mlx5e_monitor_counter_start() as a static function.
Fixes: 5c7e8bbb02 ("net/mlx5e: Use monitor counters for update stats")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch is a little improvement. Simplify the mlx5e_tc_add_fdb_flow().
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With recent introduction of flow_rule infrastructure drivers no longer
directly include action headers, so it is no longer possible to use
constants defined in them. Instead, one of flow_rule patches substituted
pedit action header constant with hardcoded value '2' in mlx5
set_pedit_val() function conditional which verifies that header type is in
range of values allowed by pedit action. That conditional is now both
wrong (hardcoded value is '2' but __PEDIT_HDR_TYPE_MAX is 6 in current
version) and superfluous (pedit action already verifies that header type is
in allowed range during init). Remove the described check from mlx5 code.
Fixes: 7386788175 ("drivers: net: use flow action infrastructure")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Take into a function the common code structure of opening
a side set of channels followed by a call to apply them.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
