When a fatal interrupt is received or it is detected that the baseband
has hung, the chip has to be reset immediately. Otherwise, we end up
processing spurious interrupts. Ensure that we bail out properly in
the ISR when the reset work hasn't completed yet.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'sc_flags' variable is being used in a number of places
with no locking whatsoever. This patch converts the usage
of sc_flags to atomic ops.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And use a helper function to setup antennae after a reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Currently, there is no synchronization between the reset
work and the tx-poll work. Fix this and make sure that we
bail out properly if a reset work is in progress.
* Cleanup the PLL WAR and enable it for AR9340 too and
use a helper for restarting work/timers after a reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add link.c and move all the link/connection monitoring
code to it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When BT FTP/PAN transmits while WLAN is idle, the one of 9462 chain
often picks up BT's tx signal and starts receiving. If the current
weight is set to be higher than BT tx, BT tx will be aborted and this
also degrades BT performance. Hence lower WLAN rx priority in this
case only when there are no WLAN traffic.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program MCI related power registers only if MCI interrupts
are enabled. This could help to reduce power consumptions when
WLAN alone is enabled in BT coex chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is waking up from sleep state, the cycle counters
might have incorrect readings. So it is better not to update those
readings with software counters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use smaller aggregation limit and increasing aggregation threshold
for osla that could improve wlan performance when there is HID profile.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When software rfkill is triggered, before put the chip in reset
state, give LNA and SPDT control to BT to make sure BT can have
good RF performance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable WLAN and BT mode for switching regulator discontinuous
orverride for AR9462 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
program BT to control SPDT everytime while loading switch table
from eeprom.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chain index to perform IQ calibration is counted to number of valid
tx chains and then used for indexing chain specific registers. If the
chainmask is set to 0x2 (i.e chain 1 only), still it accesses chain 0
registers for chain 1. So use real chain index instead sequential one.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix bad indentation & if nesting to lose about two levels
of unnecessary indentation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wrong ADC sample phase that happen between awake and
network/full sleep will lead to improper rx noisefloor
calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, use atomic operations to check the flags.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211's IEEE80211_CONF_OFFCHANNEL can be used directly
to track offchannel state. Also pass the correct boolean
value to ath9k_hw_startpcureceive().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Exposed by sparse:
ar9003_mci.c:1134:31: warning: Using plain integer as NULL pointer
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'setChip' variable is unused, remove it and
simplify the functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MCI has to be handled only when BTCOEX is actually enabled.
Check for this condition before calling MCI related functions
from various reset/calibration call-sites.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default value that is being programmed to AR_RTC_KEEP_AWAKE
is 0x2, there is no need to program it manually in various
functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MCI interrupts have to be enabled only when BTCOEX is
actually in use.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ASPM has to be disabled when BTCOEX is in use, do this properly
by calling the bus-specific ASPM init routine after the
BTCOEX scheme has been determined.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of cluttering ath9k_init_device() with 'ath_softc'
specific initialization code, use ath9k_init_softc() to
setup driver-specific work routines, timers etc.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed checkpatch and sparse warnings related to aiutils.*
Signed-off-by: Chris Yungmann <yungmann.chris@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure CWmin based on slot time for IBSS mode. This helps
in increasing the beacon distribution of ath9k to accepted
levels in 11a mode.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar like other drivers including iwl3945, do not configure group
keys to the hardware (on Ad-Hoc mode) to make IBSS RSN work.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar like other drivers, do not configure group keys to the hardware
(on Ad-Hoc mode) to make IBSS RSN work.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updates for spectral scanning register modification for AR93x:
* fix bits for spectral_scan_count
* add bits for new parameters
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We separate reading of device's eeprom content from writing it back
to the device's sram.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a debugging log when using shadow
registers. Also fix a minor typo in this
connection.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly clean up indentation around parentheses
after if, function calls, etc. and also a few
unneeded line breaks and some other things.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is a library to be used by multiple
opmodes, so move it into the iwlwifi module.
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the next step in splitting up the driver,
making the uCode API dependent pieces of it live
in separate modules. Right now there's only one
so it's not user-selectable, but we're actively
working on more.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is common, not uCode API specific, so move
it to the transport together with the command
header struct definition.
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Guy Cohen <guy.cohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is intended to be set whenever wakeup will be
needed upon suspend, not only when suspending, so
use the new callbacks to set it then.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This macro is needed by other transports besides PCIe, thus
moving to a common location.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches suggested adding the __printf attribute
to the __iwl_dbg function to check arguments; add it
to all of the logging functions (err, warn, info, dbg
and crit.)
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We missed passing an argument to the
debug print. Fix it.
Cc: stable@kernel.org
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug prints were wrong and buggy. The HW pointer wasn't printed
correctly, it was mixed up with the pointer to the rxbuf.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This chip is used at least by the D-Link DWA-525 adapter.
Signed-off-by: Alex Villac<ED>s Lasso <a_villacis@palosanto.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
