Some QSFP cables assert the interrupt line as a side effect of module
plug-in and power up. This causes the SerDes and QSFP tuning algorithm
to begin cable initialization by reading the QSFP memory map over I2C,
which fails. This patch ignores any interrupt line assertion until
the module has completed power up and voltage rails have stabilized,
which can take a maximum of 500 ms per the SFF-8679 specification.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Read the version of the SBus, PCIe SerDes, and Fabric Serdes
firmwares at driver load time.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When link up fails in LNI, the local and peer state complete
frames are reported as numbers. Explain what the values mean
so the operator can better diagnose the problem.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, the default number of kernel receive contexts is set to the
number of NUMA nodes on the system plus one for control context. However,
the systems that have a single socket and/or have NUMA disabled in the BIOS
will have only one receive context by default. This patch would ensure that
by default there will be at least two kernel receive contexts plus one for
control context regardless of the number of NUMA nodes on the system. The
user can override the default number of kernel receive contexts with the
krcvqs module parameter.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove the TWSI code. The driver now uses the kernel's built-in
i2c bit bus module.
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use built-in i2c bit-shift bus adapter to control the
i2c busses on the chip.
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When HFI units get initialized, they each use their own mask copy for
affinity assignments. On a multi-HFI system, affinity assignments
overbook CPU cores as each HFI doesn't have knowledge of affinity
assignments for other HFI units. Therefore, some CPU cores are never
used for interrupt handlers in systems with high number of CPU cores
per NUMA node.
For multi-HFI systems, SDMA engine interrupt assignments start all over
from the first CPU in the local NUMA node after the first HFI
initialization. This change allows assignments to continue where the
last HFI unit left off.
Add global structure for affinity assignments for multiple HFIs to share
affinity mask.
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Reviewed-by: Jubin John <jubin.john@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add sw counter to track dropped unsupported packets.
Report unsupported packets drop as the RcvError.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The critical section should protect only the list traversal
and dd->asic_data modification, not the memory allocation.
The fix pulls the allocation out of the critical section.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Swapping a cable from a "Mgmt Allowed=No" switch port to a
"Mgmt Allowed=Yes" switch port doesn't send a pkey change
notification. Therefore, the link doesn't become active as
the oib_utils layer uses an old pkey table cache.
Fix by ensuring the pkey change notification is sent when
the table is changed both explicitly by the FM and implicitly
by the driver via a cable swap.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
FULL_MGMT_P_KEY doesn't get cleared from the pkey table at link bounce
because the link down and link bounce code paths are different when
moving a QSFP cable on a switch. This causes an HFI unit connected to a
switch to try to be initialized to an FM node when the QSFP cable is
moved from a MgmtAllowed=NO port to a MgmtAllowed=YES port and back to a
MgmtAllowed=NO port. Remove FULL_MGMT_P_KEY from pkey table at link up.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The credit return threshold adjustment on mtu change algorithm does not
take into account all the kernel send contexts that are assigned per VL.
Use the pio send context map to adjust the credit return thresholds for
all the allocated and assigned kernel send contexts based on the MTU
adjustment per VL.
The pio send context map can be changed dynamically based on the actual
number of operational vls which is set by the fabric manager. When this
happens update the credit return threshold values for all the remapped
kernel send contexts.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Make the indentation of the source code consistent. Detected by
smatch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When FM is disabled, and the HFI port on the switch is
changed from MgmtAllowed=YES to MgmtAllowed=NO and the
link is bounced, FULL_MGMT_P_KEY doesn't get cleared
from the pkey table. This also occurs when the QSFP
cable is moved from a switch port with MgmtAllowed=YES
to a MgmtAllowed=NO port. Clear pkey entry properly.
Also, when the driver is loaded and the switch port is
set to MgmtAllowed=NO, FULL_MGMT_P_KEY shouldn't be added
to pkey table after FM is started. Only set FULL_MGMT_P_KEY
in the pkey table if switch port is configured to
MgmtAllowed=YES.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The TODO list for the hfi1 driver was completed during 4.6. In addition
other objections raised (which are far beyond what was in the TODO list)
have been addressed as well. It is now time to remove the driver from
staging and into the drivers/infiniband sub-tree.
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
