The header for I2Sv2
linux/arch/arm/plat-s3c/include/plat/regs-s3c2412-iis.h
contains only controller specific definitions and nothing
SoC specific. So, it could be moved to sound/soc/s3c24xx/
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Towards having build for multiple SoCs segregate hw_params callback
for s3c2412 and s3c64xx.
Since, all new SoCs have s3c64xx like register map, we keep that as
default implementation if no SoC specific callback is already defined.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For some CPU-CODEC and source clock combination we might need to set
BCLK to N*Sample_size*LRCLK, where N may be even 3 or 4, not just 2.
We can simply remove the dependency of BCLK on sample size as there
is already a callback(S3C_I2SV2_DIV_BCLK) available to set required BCLK.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Towards generalizing CPU driver interface, do not accept direct field
values for the BCLK and RCLK.
The machine driver should simply request the FS-multiple and not provide
the value to be set in divide field of IISMOD.
[Confirmed by Jassi that no existing machine drivers are affected --
broonie]
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Report the current FIFO depth when delay is queried. The FIFO is only
16 frames deep so the latency will be at most a couple of miliseconds
(and we tend to end up reporting zero most of the time) but it may
help some applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Making room for namespace for the PCM Controller driver
the platform driver(s3c24xx-pcm) has been renamed to SoC
agnostic name 's3c-dma'.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The s3c24xx_pcm prefix for the soc_platform is inappropriate when
some Samsung SoCs have PCM controllers which will eventually have
drivers and hence namespace ambiguities.
To resolve naming ambiguities in future the following have been
renamed in order
1) s3c24xx_pcm_dma_params -> s3c_dma_params
2) s3c24xx_pcm_preallocate_dma_buffer -> s3c_preallocate_dma_buffer
3) s3c24xx_pcm_dmamask -> s3c_dma_mask
4) s3c24xx_pcm_XXX -> s3c_dma_XXX
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove the <plat/audio.h> include from arch/arm/plat-s3c/include/plat/audio.h
as it provides nothing to the current kernel and is not in any future plans
for the system.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
1) Explicitly set LRCLK polarity for I2S Vs LSM/MSB modes.
2) Convert from numerical to bit-field values for BCLK selection.
3) Use proper error checking for return value from clk_get
Signed-off-by: Jassi <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
s3c2412_snd_lrsync() maybe reached with IRQs disabled and if LRCLK
is dead due to improper initialization of CPU or CODEC, the system
gets stuck in the loop because jiffies may never get updated.
Implemented counter based wait mechanism for atleast the same
timeout period.
Signed-off-by: Jassi <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
s3c24xx dma has the auto reload feature, when the the trnasfer is done,
CURR_TC(DSTAT[19:0], current value of transfer count) reaches 0, and DMA
ACK becomes 1, and then, TC(DCON[19:0]) will be loaded into CURR_TC. So
the transmission is repeated.
IRQ is issued while auto reload occurs. We change the DISRC and
DCON[19:0] in the ISR, but at this time, the auto reload has been
performed already. The first block is being re-transmitted by the DMA.
So we need rewrite the DISRC and DCON[19:0] for the next block
immediatly after the this block has been started to be transported.
The function s3c2410_dma_started() is for this perpose, which is called
in the form of "s3c2410_dma_ctrl(prtd->params->channel,
S3C2410_DMAOP_STARTED);" in s3c24xx_pcm_trigger().
But it is not correct. DMA transmission won't start until DMA REQ signal
arrived, it is the time s3c24xx_snd_txctrl(1) or s3c24xx_snd_rxctrl(1)
is called in s3c24xx_i2s_trigger().
In the current framework, s3c24xx_pcm_trigger() is always called before
s3c24xx_pcm_trigger(). So the s3c2410_dma_started() should be called in
s3c24xx_pcm_trigger() after s3c24xx_snd_txctrl(1) or
s3c24xx_snd_rxctrl(1) is called in this function.
However, s3c2410_dma_started() is dma related, to call this function we
should provide the channel number, which is given by
substream->runtime->private_data->params->channel. The private_data
points to a struct s3c24xx_runtime_data object, which is define in
s3c24xx_pcm.c, so s3c2410_dma_started() can't be called in s3c24xx_i2s.c
Fix this by moving the call to signal the DMA started to the DAI
drivers.
Signed-off-by: Shine Liu <liuxian@redflag-linux.com>
Signed-off-by: Shine Liu <shinel@foxmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The data format configuration for S3C64xx IISv2 was hardcoded for IISMOD
register. This patch changes to the defined values it.
And instead of bits 9 and 10 of IISMOD we should clear bits 13 and 14.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unsigned variables should use `%u' rather than `%d'.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They aren't used by anything external and aren't prototyped; if any
users appear they can be exported again for them.
Also report what modes we have a problem with when we encounter invalid
mode configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On startup we try to make sure that the port is quiesced but if the
port is already stopped then this will generate a warning about the
RX/TX mode configuration. Configure the mode before doing the teardown
to suppress these warnings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The data format configuration for S3C64xx IISv2 is completely different
to that for S3C24xx. Instead of a single bit configuration in bit 0 of
IISMOD we have format selection in bits 13 and 14 and bit clock rate
selection in bits 1 and 2. While we're here add support for 24 bit
samples in S3C64xx.
At some point it may be desirable to expose the bit clock rate selection
to users but given the limited configuration options that may not be
required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Say what invalid values we're seeing when we see an invalid value and
ensure that errors are displayed by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the build error in s3c-i2s-v2.c caused by
a change to the snd_soc_dai ops field.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The definition of s3c_i2sv2_iis_calc_rate was never
renamed from s3c2412_iis_calc_rate, so rename this
to allow the build to work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Upgrade the severity of some failure messages from debug level so
they're displayed by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The recent set of S3C64xx patches re-added a lot of uses of DBG() that
had previously been removed - revert this so the standard pr_debug()
macro is used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The S3C2412 I2S (IIS) interface is replicated on further Samsung SoC
parts in a broadly compatible way, so split the common code out into
a core called s3c-i2s-v2.[ch] so that the newer SoCs such as the
S3C6410 can make use of it.
As such, all the original s3c2412 functions are currently being left
with their original names, and will be renamed later in the series.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
