Convert the uses of memcpy to ether_addr_copy because
for some architectures it is smaller and faster.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the more obvious uses of memcpy to ether_addr_copy.
There are still uses of memcpy that could be converted but
these addresses are __aligned(2).
Convert a couple uses of 6 in gr_private.h to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_is_cwnd_limited() allows GSO/TSO enabled flows to increase
their cwnd to allow a full size (64KB) TSO packet to be sent.
Non GSO flows only allow an extra room of 3 MSS.
For most flows with a BDP below 10 MSS, this results in a bloat
of cwnd reaching 90, and an inflate of RTT.
Thanks to TSO auto sizing, we can restrict the bloat to the number
of MSS contained in a TSO packet (tp->xmit_size_goal_segs), to keep
original intent without performance impact.
Because we keep cwnd small, it helps to keep TSO packet size to their
optimal value.
Example for a 10Mbit flow, with low TCP Small queue limits (no more than
2 skb in qdisc/device tx ring)
Before patch :
lpk51:~# ./ss -i dst lpk52:44862 | grep cwnd
cubic wscale:6,6 rto:215 rtt:15.875/2.5 mss:1448 cwnd:96
ssthresh:96
send 70.1Mbps unacked:14 rcv_space:29200
After patch :
lpk51:~# ./ss -i dst lpk52:52916 | grep cwnd
cubic wscale:6,6 rto:206 rtt:5.206/0.036 mss:1448 cwnd:15
ssthresh:14
send 33.4Mbps unacked:4 rcv_space:29200
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Van Jacobson <vanj@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation misses a few of the supported flags. Fix this. Also
respect the dependency to CONFIG_XFRM for the IPSEC flag.
Cc: Fan Du <fan.du@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'out' label is just a relict from previous times as pgctrl_write()
had multiple error paths. Get rid of it and simply return right away
on errors.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a privileged user writes an empty string to /proc/net/pktgen/pgctrl
the code for stripping the (then non-existent) '\n' actually writes the
zero byte at index -1 of data[]. The then still uninitialized array will
very likely fail the command matching tests and the pr_warning() at the
end will therefore leak stack bytes to the kernel log.
Fix those issues by simply ensuring we're passed a non-empty string as
the user API apparently expects a trailing '\n' for all commands.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
1) Introduce skb_to_sgvec_nomark function to add further data to the sg list
without calling sg_unmark_end first. Needed to add extended sequence
number informations. From Fan Du.
2) Add IPsec extended sequence numbers support to the Authentication Header
protocol for ipv4 and ipv6. From Fan Du.
3) Make the IPsec flowcache namespace aware, from Fan Du.
4) Avoid creating temporary SA for every packet when no key manager is
registered. From Horia Geanta.
5) Support filtering of SA dumps to show only the SAs that match a
given filter. From Nicolas Dichtel.
6) Remove caching of xfrm_policy_sk_bundles. The cached socket policy bundles
are never used, instead we create a new cache entry whenever xfrm_lookup()
is called on a socket policy. Most protocols cache the used routes to the
socket, so this caching is not needed.
7) Fix a forgotten SADB_X_EXT_FILTER length check in pfkey, from Nicolas
Dichtel.
8) Cleanup error handling of xfrm_state_clone.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To be friendly to user space and to behave well with controllers that
lack a proper internal power off procedure we should try to clean up as
much state as possible before requesting the HCI driver to power off.
This patch updates the power off procedure that's triggered by
mgmt_set_powered to clean any scan modes, stop LE scanning and
advertising and to disconnect any open connections.
The asynchronous cleanup procedure uses the HCI request framework,
however since HCI_Disconnect is only covered until its Command Status
event we need some extra tracking/waiting of disconnections. This is
done by monitoring when hci_conn_count() indicates that there are no
more connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) is updated to clear the scan mode we should
not just blindly clear the HCI_ADVERTISING flag in mgmt_advertising()
but first check if there is a pending set_powered operation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) is updated to clear the scan mode we should
not just blindly clear the HCI_CONNECTABLE flag in mgmt_connectable()
but first check if there is a pending set_powered operation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) is updated to clear the scan mode we should
not just blindly clear the HCI_DISCOVERABLE flag in mgmt_discoverable()
but first check if there is a pending set_powered operation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once mgmt_set_powered(off) starts doing disconnections we'll need to
care about any disconnections in mgmt.c and not just those with the
MGMT_CONNECTED flag set. Therefore, move the check into mgmt.c from
hci_event.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need to make decisions on toggling the HCI_ADVERTISING flag
based on pending mgmt_set_powered commands. Therefore, move the handling
from hci_event.c into mgmt.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The RPA expiry timer is only initialized inside mgmt.c when we receive
the first command from user space. This action also involves setting the
HCI_MGMT flag for the first time so that flag acts as a good indicator
of whether the delayed work variable can be touched or not. This patch
fixes hci_dev_do_close to first check the flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A user space that supports the Set Privacy command is also expected to
be able to handle New IRK events. Therefore, set the HCI_RPA_RESOLVING
flag whenever the Set Privacy command is received.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The MLME code in mac80211 must track whether or not the AP changed
bandwidth, but if there's no change while tracking it shouldn't do
anything, otherwise regulatory updates can make it impossible to
connect to certain APs if the regulatory database doesn't match the
information from the AP. See the precise scenario described in the
code.
This still leaves some possible problems with CSA or if the AP
actually changed bandwidth, but those cases are less common and
won't completely prevent using it.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=70881
Cc: stable@vger.kernel.org
Reported-and-tested-by: Nate Carlson <kernel@natecarlson.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The identity information in debugfs currently do not include the
current in use local RPA. Since the RPA is now stored in the
controller information, include it in the debugfs as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The RPA needs to be stored to know which is the current one. Otherwise
it is impossible to ensure that always the correct RPA can be programmed
into the controller when it is needed.
Current code checks if the address in the controller is a RPA, but that
can potentially lead to using a RPA that can not be resolved with the
IRK that has been distributed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When enabling non-connectable advertising, there is no need to advertise
with a public address or static address. In case LE privacy has not been
enabled a unresolvable private address will be used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When running active scanning during LE discovery, do not reveal the own
identity to the peer devices. In case LE privacy has been enabled, then
a resolvable private address is used. If the LE privacy option is off,
then use an unresolvable private address.
The public address or static random address is never used in active
scanning anymore. This ensures that scan request are send using a
random address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using LE Privacy it is useful to know the local identity address,
identity address type and identity resolving key. For debugging purposes
add these information to debugfs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The check should be for setup function pointer.
This patch fixes NULL pointer dereference issue for NCI
based NFC driver which doesn't define setup handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that the identity address type is always looked up for all
successful connections, the hdev->own_addr_type variable has become
completely unnecessary. Simply remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch ensures that conn->src_type contains the same address type as
is used for initiating the connection while the connection attempt is in
progress. Once connected this value will be overwritten with the
identity address type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for handling the Set Privacy mgmt command,
including copying the value to hdev->irk and toggling the HCI_PRIVACY
flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a rpa_timeout debugfs entry which can be used to set the
RPA regeneration timeout to something else than the default 15 minutes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we always update the random address before enabling advertising,
scanning and initiating LE connections there is no need to write the
random address add power on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we start LE scanning we need to update the local random address if
necessary. This patch updates the code to use hci_update_random_address()
for setting the own_address_type scan parameter and updating the local
random address if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we enable advertising we need to update the local random address if
necessary. This patch takes advantage of the hci_update_random_address()
function to set the own_address_type variable and to update the local
random address if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we initiate LE connections we need to update the local random
address if necessary. This patch updates the LE connection creation
mechanism to use the new hci_update_random_address() function to set the
own_address_type parameter and to update the local random address if
necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a convenience function for updating the local random
address which is needed before advertising, scanning and initiating LE
connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a timer for updating the local RPA periodically. The
default timeout is set to 15 minutes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need a function in smp.c to generate Resolvable Random Addresses in
order to support privacy. The local RPA will need to be generated before
advertising, scanning or connecting and regenerated at periodic
intervals. This patch adds the necessary function for RPA generation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SMP Identity Address Information PDU should contain our Identity
Address. This patch updates the code to copy the correct values from the
hci_conn object.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be consistent with the remote address info in hci_conn we want it to
also contain the local identity address information. This patch updates
the code to copy the right values in place whenever an LE connection has
been established.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes sure that the Privacy flag is available in the mgmt
supported settings for all LE capable controllers and in the current
settings whenever the HCI_PRIVACY flag is set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These functions will soon be needed by the RPA regeneration timeout so
move them higher up in mgmt.c to avoid a forward declaration.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This code adds a HCI_PRIVACY flag to track whether Privacy support is
enabled (meaning we have a local IRK) and makes sure the IRK is
distributed during SMP key distribution in case this flag is set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch a couple of helper variables to the smp_distribute_keys
function in order to avoid long chains of dereferences and thereby help
readability.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The event opcode for New Identity Resolving Key event is missing from
supported event list. Just add it there.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Currently we generate a new fragmentation id on UFO segmentation. It
is pretty hairy to identify the correct net namespace and dst there.
Especially tunnels use IFF_XMIT_DST_RELEASE and thus have no skb_dst
available at all.
This causes unreliable or very predictable ipv6 fragmentation id
generation while segmentation.
Luckily we already have pregenerated the ip6_frag_id in
ip6_ufo_append_data and can use it here.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem statement: 1) both paths (primary path1 and alternate
path2) are up after the association has been established i.e.,
HB packets are normally exchanged, 2) path2 gets inactive after
path_max_retrans * max_rto timed out (i.e. path2 is down completely),
3) now, if a transmission times out on the only surviving/active
path1 (any ~1sec network service impact could cause this like
a channel bonding failover), then the retransmitted packets are
sent over the inactive path2; this happens with partial failover
and without it.
Besides not being optimal in the above scenario, a small failure
or timeout in the only existing path has the potential to cause
long delays in the retransmission (depending on RTO_MAX) until
the still active path is reselected. Further, when the T3-timeout
occurs, we have active_patch == retrans_path, and even though the
timeout occurred on the initial transmission of data, not a
retransmit, we end up updating retransmit path.
RFC4960, section 6.4. "Multi-Homed SCTP Endpoints" states under
6.4.1. "Failover from an Inactive Destination Address" the
following:
Some of the transport addresses of a multi-homed SCTP endpoint
may become inactive due to either the occurrence of certain
error conditions (see Section 8.2) or adjustments from the
SCTP user.
When there is outbound data to send and the primary path
becomes inactive (e.g., due to failures), or where the SCTP
user explicitly requests to send data to an inactive
destination transport address, before reporting an error to
its ULP, the SCTP endpoint should try to send the data to an
alternate __active__ destination transport address if one
exists.
When retransmitting data that timed out, if the endpoint is
multihomed, it should consider each source-destination address
pair in its retransmission selection policy. When retransmitting
timed-out data, the endpoint should attempt to pick the most
divergent source-destination pair from the original
source-destination pair to which the packet was transmitted.
Note: Rules for picking the most divergent source-destination
pair are an implementation decision and are not specified
within this document.
So, we should first reconsider to take the current active
retransmission transport if we cannot find an alternative
active one. If all of that fails, we can still round robin
through unkown, partial failover, and inactive ones in the
hope to find something still suitable.
Commit 4141ddc02a ("sctp: retran_path update bug fix") broke
that behaviour by selecting the next inactive transport when
no other active transport was found besides the current assoc's
peer.retran_path. Before commit 4141ddc02a, we would have
traversed through the list until we reach our peer.retran_path
again, and in case that is still in state SCTP_ACTIVE, we would
take it and return. Only if that is not the case either, we
take the next inactive transport.
Besides all that, another issue is that transports in state
SCTP_UNKNOWN could be preferred over transports in state
SCTP_ACTIVE in case a SCTP_ACTIVE transport appears after
SCTP_UNKNOWN in the transport list yielding a weaker transport
state to be used in retransmission.
This patch mostly reverts 4141ddc02a, but also rewrites
this function to introduce more clarity and strictness into
the code. A strict priority of transport states is enforced
in this patch, hence selection is active > unkown > partial
failover > inactive.
Fixes: 4141ddc02a ("sctp: retran_path update bug fix")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Acked-by: Vlad Yasevich <yasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes bug introduced by:
commit 1d4c8c2984
"neigh: restore old behaviour of default parms values"
The thing is that in neigh_sysctl_register, extra1 and extra2 which were
previously set for NEIGH_VAR_GC_* are overwritten. That leads to
nonsense int limits for gc_* variables. So fix this by not touching
extra* fields for gc_* variables.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two bugs in fastopen :
1) The tcp_sendmsg(..., @size) argument was ignored.
Code was relying on user not fooling the kernel with iovec mismatches
2) When MTU is about 64KB, tcp_send_syn_data() attempts order-5
allocations, which are likely to fail when memory gets fragmented.
Fixes: 783237e8da ("net-tcp: Fast Open client - sending SYN-data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Tested-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accidentally a side effect is involved by commit 6e967adf7(tipc:
relocate common functions from media to bearer). Now tipc stack
handler of receiving packets from netdevices as well as netdevice
notification handler are registered when bearer is enabled rather
than tipc module initialization stage, but the two handlers are
both unregistered in tipc module exit phase. If tipc module is
inserted and then immediately removed, the following warning
message will appear:
"dev_remove_pack: ffffffffa0380940 not found"
This is because in module insertion stage tipc stack packet handler
is not registered at all, but in module exit phase dev_remove_pack()
needs to remove it. Of course, dev_remove_pack() cannot find tipc
protocol handler from the kernel protocol handler list so that the
warning message is printed out.
But if registering the two handlers is adjusted from enabling bearer
phase into inserting module stage, the warning message will be
eliminated. Due to this change, tipc_core_start_net() and
tipc_core_stop_net() can be deleted as well.
Reported-by: Wang Weidong <wangweidong1@huawei.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc module is inserted, many tipc components are initialized
one by one. During the initialization period, if one of them is
failed, tipc_core_stop() will be called to stop all components
whatever corresponding components are created or not. To avoid to
release uncreated ones, relevant components have to add necessary
enabled flags indicating whether they are created or not.
But in the initialization stage, if one component is unsuccessfully
created, we will just destroy successfully created components before
the failed component instead of all components. All enabled flags
defined in components, in turn, become redundant. Additionally it's
also unnecessary to identify whether table.types is NULL in
tipc_nametbl_stop() because name stable has been definitely created
successfully when tipc_nametbl_stop() is called.
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be iterating hdev->identity_resolving_keys in the
hci_remove_irk() function instead of hdev->long_term_keys. This patch
fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Error codes returned by cfg80211_chandef_dfs_required() are ignored
when trying to join an IBSS. Fix this by printing an error and
returning.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't have to double check whether the parameters passed to
cfg80211_can_use_iftype_chan() are correct. We should just make sure
they *are* when we call this function.
Remove the radar_detect argument check in
cfg80211_can_use_iftype_chan() to simplify the code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[keep braces around a long comment + single statement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mesh support for DFS channels was added, we also need to check
for DFS channels when performing a channel switch with
NL80211_IFTYPE_MESHPOINT.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[use switch statement, slight code cleanup]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously we were warning and using automatic when a driver sent an
update request with SMPS off. This patch makes it possible for
drivers to disable SMPS at runtime, for whatever reason.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce NL80211_RRF_AUTO_BW rule flag. If this flag set
maximum available bandwidth should be calculated base on
contiguous rules and wider channels will be allowed to cross
multiple contiguous/overlapping frequency ranges.
In case of old kernels maximum bandwidth from regulatory
rule will be used, while there is no NL80211_RRF_AUTO_BW flag.
This fixes the previous commit 9752482083
("cfg80211: regulatory introduce maximum bandwidth calculation")
which was found to be a problem for userspace API compatibility.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[edit commit log, use sizeof()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The error pointer passed to xfrm_state_clone() is unchecked,
so remove it and indicate an error by returning a null pointer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch fixes commit d3623099d3 ("ipsec: add support of limited SA dump").
sadb_ext_min_len array should be updated with the new type (SADB_X_EXT_FILTER).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
With the addition of Resolvable Private Address (RPA) resolution
support for Bluetooth Low Energy connections, it makes sense to
increase the minor version of the Bluetooth core module.
The module version is not used anywhere, but it gives a nice extra
hint for debugging purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For testing purposes it is useful to provide an option to change the
advertising channel map. So add a debugfs option to allow this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When binding RFCOMM socket with non-zero channel we're checking if
there is already any other socket which has the same channel number
assigned and then fail. This check does not consider situation where
we have another socket connected to remote device on given channel
number in which case we still should be able to bind local socket.
This patch changes __rfcomm_get_sock_by_addr() to return only sockets
in either BT_BOUND or BT_LISTEN states, also name is updated to better
describe what this function does now.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In current implementation it is possible to reach PF state from unconfirmed.
We can interpret sctp-failover-02 in a way that PF state is meant to be reached
only from active state, in the end, this is when entering PF state makes sense.
Here are few quotes from sctp-failover-02, but regardless of these, same
understanding can be reached from whole section 5:
Section 5.1, quickfailover guide:
"The PF state is an intermediate state between Active and Failed states."
"Each time the T3-rtx timer expires on an active or idle
destination, the error counter of that destination address will
be incremented. When the value in the error counter exceeds
PFMR, the endpoint should mark the destination transport address as PF."
There are several concrete reasons for such interpretation. For start, rfc4960
does not take into concern quickfailover algorithm. Therefore, quickfailover
must comply to 4960. Point where this compliance can be argued is following
behavior:
When PF is entered, association overall error counter is incremented for each
missed HB. This is contradictory to rfc4960, as address, while in unconfirmed
state, is subjected to probing, and while it is probed, it should not increment
association overall error counter. This has as a consequence that we might end
up in situation in which we drop association due path failure on unconfirmed
address, in case we have wrong configuration in a way:
Association.Max.Retrans == Path.Max.Retrans.
Another reason is that entering PF from unconfirmed will cause a loss of address
confirmed event when address is once (if) confirmed. This is fine from failover
guide point of view, but it is not consistent with behavior preceding failover
implementation and recommendation from 4960:
5.4. Path Verification
Whenever a path is confirmed, an indication MAY be given to the upper
layer.
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug introduced by commit 7d442fab0a ("ipv4: Cache dst in tunnels").
Because sit code does not call ip_tunnel_init(), the dst_cache was not
initialized.
CC: Tom Herbert <therbert@google.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to solve races with sched_scan_stop, it is necessary
for the driver to be able to return an error to propagate that
to cfg80211 so it doesn't send an event.
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We loose a lot of information of the original state if we
clone it with xfrm_state_clone(). In particular, there is
no crypto algorithm attached if the original state uses
an aead algorithm. This patch add the missing information
to the clone state.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
A comment on xfrm_migrate_state_find() says that xfrm_state_lock
is held. This is apparently not the case, but we need it to
traverse through the state lists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
xfrm_state_sort() takes the unsorted states from the src array
and stores them into the dst array. We try to get the namespace
from the dst array which is empty at this time, so take the
namespace from the src array instead.
Fixes: 283bc9f35b ("xfrm: Namespacify xfrm state/policy locks")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Since commit 469bdcefdc ip6_vti uses ip_tunnel_get_stats64(),
so we need to select NET_IP_TUNNEL to have this function available.
Fixes: 469bdcefdc ("ipv6: fix the use of pcpu_tstats in ip6_vti.c")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct
the VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the
presence of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Consider the following (relatively unlikely) scenario:
1) station goes to sleep while frames are buffered in driver
2) driver blocks wakeup (until no more frames are buffered)
3) station wakes up again
4) driver unblocks wakeup
In this case, the current mac80211 code will do the following:
1) WLAN_STA_PS_STA set
2) WLAN_STA_PS_DRIVER set
3) - nothing -
4) WLAN_STA_PS_DRIVER cleared
As a result, no frames will be delivered to the client, even
though it is awake, until it sends another frame to us that
triggers ieee80211_sta_ps_deliver_wakeup() in sta_ps_end().
Since we now take the PS spinlock, we can fix this while at
the same time removing the complexity with the pending skb
queue function. This was broken since my commit 50a9432dae
("mac80211: fix powersaving clients races") due to removing
the clearing of WLAN_STA_PS_STA in the RX path.
While at it, fix a cleanup path issue when a station is
removed while the driver is still blocking its wakeup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a race condition in mac80211 because we add stations
to the internal lists after adding them to the driver, which
means that (for example) the following can happen:
1. a station connects and is added
2. first, it is added to the driver
3. then, it is added to the mac80211 lists
If the station goes to sleep between steps 2 and 3, and the
firmware/hardware records it as being asleep, mac80211 will
never instruct the driver to wake it up again as it never
realized it went to sleep since the RX path discarded the
frame as a "spurious class 3 frame", no station entry was
present yet.
Fix this by adding the station in software first, and only
then adding it to the driver. That way, any state that the
driver changes will be reflected properly in mac80211's
station state. The problematic part is the roll-back if the
driver fails to add the station, in that case a bit more is
needed. To not make that overly complex prevent starting BA
sessions in the meantime.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a race between the TX path and the STA wakeup: while
a station is sleeping, mac80211 buffers frames until it wakes
up, then the frames are transmitted. However, the RX and TX
path are concurrent, so the packet indicating wakeup can be
processed while a packet is being transmitted.
This can lead to a situation where the buffered frames list
is emptied on the one side, while a frame is being added on
the other side, as the station is still seen as sleeping in
the TX path.
As a result, the newly added frame will not be send anytime
soon. It might be sent much later (and out of order) when the
station goes to sleep and wakes up the next time.
Additionally, it can lead to the crash below.
Fix all this by synchronising both paths with a new lock.
Both path are not fastpath since they handle PS situations.
In a later patch we'll remove the extra skb queue locks to
reduce locking overhead.
BUG: unable to handle kernel
NULL pointer dereference at 000000b0
IP: [<ff6f1791>] ieee80211_report_used_skb+0x11/0x3e0 [mac80211]
*pde = 00000000
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
EIP: 0060:[<ff6f1791>] EFLAGS: 00210282 CPU: 1
EIP is at ieee80211_report_used_skb+0x11/0x3e0 [mac80211]
EAX: e5900da0 EBX: 00000000 ECX: 00000001 EDX: 00000000
ESI: e41d00c0 EDI: e5900da0 EBP: ebe458e4 ESP: ebe458b0
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 000000b0 CR3: 25a78000 CR4: 000407d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Process iperf (pid: 3934, ti=ebe44000 task=e757c0b0 task.ti=ebe44000)
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command LQ_CMD (#4e), seq: 0x0903, 92 bytes at 3[3]:9
Stack:
e403b32c ebe458c4 00200002 00200286 e403b338 ebe458cc c10960bb e5900da0
ff76a6ec ebe458d8 00000000 e41d00c0 e5900da0 ebe458f0 ff6f1b75 e403b210
ebe4598c ff723dc1 00000000 ff76a6ec e597c978 e403b758 00000002 00000002
Call Trace:
[<ff6f1b75>] ieee80211_free_txskb+0x15/0x20 [mac80211]
[<ff723dc1>] invoke_tx_handlers+0x1661/0x1780 [mac80211]
[<ff7248a5>] ieee80211_tx+0x75/0x100 [mac80211]
[<ff7249bf>] ieee80211_xmit+0x8f/0xc0 [mac80211]
[<ff72550e>] ieee80211_subif_start_xmit+0x4fe/0xe20 [mac80211]
[<c149ef70>] dev_hard_start_xmit+0x450/0x950
[<c14b9aa9>] sch_direct_xmit+0xa9/0x250
[<c14b9c9b>] __qdisc_run+0x4b/0x150
[<c149f732>] dev_queue_xmit+0x2c2/0xca0
Cc: stable@vger.kernel.org
Reported-by: Yaara Rozenblum <yaara.rozenblum@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
[reword commit log, use a separate lock]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
net/built-in.o:(.rodata+0x1707c): undefined reference to `ip_tunnel_get_stats64'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Bluetooth controllers with LE support, track the value of the
currently configured random address. It is important to know what
the current random address is to avoid unneeded attempts to set
a new address. This will become important when introducing the
LE privacy support in the future.
In addition expose the current configured random address via
debugfs for debugging purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The own_address_type debugfs option does not providing enough
flexibity for interacting with the upcoming LE privacy support.
What really is needed is an option to force using the static address
compared to the public address. The new force_static_address debugfs
option does exactly that. In addition it is also only available when
the controller does actually have a public address. For single mode
LE only controllers this option will not be available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The code itself is not descriptive on what store hint is used for
long term keys and why. So add some extensive comment here. Similar
to what has already been done for identity resolving key store hint.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The identity resolving keys should only be stored for devices using
resolvable random addresses. If the device is already using an
identity address, inform it about the new identity resolving key,
but tell userspace that this key is not persistent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Currently the kernel tries to announce a zero window when free_space
is below the current receiver mss estimate.
When a sender is transmitting small packets and reader consumes data
slowly (or not at all), receiver might be unable to shrink the receive
win because
a) we cannot withdraw already-commited receive window, and,
b) we have to round the current rwin up to a multiple of the wscale
factor, else we would shrink the current window.
This causes the receive buffer to fill up until the rmem limit is hit.
When this happens, we start dropping packets.
Moreover, tcp_clamp_window may continue to grow sk_rcvbuf towards rmem[2]
even if socket is not being read from.
As we cannot avoid the "current_win is rounded up to multiple of mss"
issue [we would violate a) above] at least try to prevent the receive buf
growth towards tcp_rmem[2] limit by attempting to move to zero-window
announcement when free_space becomes less than 1/16 of the current
allowed receive buffer maximum. If tcp_rmem[2] is large, this will
increase our chances to get a zero-window announcement out in time.
Reproducer:
On server:
$ nc -l -p 12345
<suspend it: CTRL-Z>
Client:
#!/usr/bin/env python
import socket
import time
sock = socket.socket()
sock.setsockopt(socket.IPPROTO_TCP, socket.TCP_NODELAY, 1)
sock.connect(("192.168.4.1", 12345));
while True:
sock.send('A' * 23)
time.sleep(0.005)
socket buffer on server-side will grow until tcp_rmem[2] is hit,
at which point the client rexmits data until -EDTIMEOUT:
tcp_data_queue invokes tcp_try_rmem_schedule which will call
tcp_prune_queue which calls tcp_clamp_window(). And that function will
grow sk->sk_rcvbuf up until it eventually hits tcp_rmem[2].
Thanks to Eric Dumazet for running regression tests.
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a message could not be sent out because the destination node
or link could not be found, the full message size is returned from
sendmsg() as if it had been sent successfully. An application will
then get a false indication that it's making forward progress. This
problem has existed since the initial commit in 2.6.16.
We change this to return -ENETUNREACH if the message cannot be
delivered due to the destination node/link being unavailable. We
also get rid of the redundant tipc_reject_msg call since freeing
the buffer and doing a tipc_port_iovec_reject accomplishes exactly
the same thing.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we decide in udp6_sendmsg to send the packet down the ipv4
udp_sendmsg path because the destination is either of family AF_INET or
the destination is an ipv4 mapped ipv6 address, we don't honor the
maybe specified ipv4 mapped ipv6 address in IPV6_PKTINFO.
We simply can check for this option in ip_cmsg_send because no calls to
ipv6 module functions are needed to do so.
Reported-by: Gert Doering <gert@space.net>
Cc: Tore Anderson <tore@fud.no>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include stable fixes for the following bugs:
- General performance regression due to NFS_INO_INVALID_LABEL being set
when the server doesn't support labeled NFS
- Hang in the RPC code due to a socket out-of-buffer race
- Infinite loop when trying to establish the NFSv4 lease
- Use-after-free bug in the RPCSEC gss code.
- nfs4_select_rw_stateid is returning with a non-zero error value on success
Other bug fixes:
- Potential memory scribble in the RPC bi-directional RPC code
- Pipe version reference leak
- Use the correct net namespace in the new NFSv4 migration code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tll2
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.14-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include stable fixes for the following bugs:
- General performance regression due to NFS_INO_INVALID_LABEL being
set when the server doesn't support labeled NFS
- Hang in the RPC code due to a socket out-of-buffer race
- Infinite loop when trying to establish the NFSv4 lease
- Use-after-free bug in the RPCSEC gss code.
- nfs4_select_rw_stateid is returning with a non-zero error value on
success
Other bug fixes:
- Potential memory scribble in the RPC bi-directional RPC code
- Pipe version reference leak
- Use the correct net namespace in the new NFSv4 migration code"
* tag 'nfs-for-3.14-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS fix error return in nfs4_select_rw_stateid
NFSv4: Use the correct net namespace in nfs4_update_server
SUNRPC: Fix a pipe_version reference leak
SUNRPC: Ensure that gss_auth isn't freed before its upcall messages
SUNRPC: Fix potential memory scribble in xprt_free_bc_request()
SUNRPC: Fix races in xs_nospace()
SUNRPC: Don't create a gss auth cache unless rpc.gssd is running
NFS: Do not set NFS_INO_INVALID_LABEL unless server supports labeled NFS
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
* Fix nf_trace in nftables if XT_TRACE=n, from Florian Westphal.
* Don't use the fast payload operation in nf_tables if the length is
not power of 2 or it is not aligned, from Nikolay Aleksandrov.
* Fix missing break statement the inet flavour of nft_reject, which
results in evaluating IPv4 packets with the IPv6 evaluation routine,
from Patrick McHardy.
* Fix wrong kconfig symbol in nft_meta to match the routing realm,
from Paul Bolle.
* Allocate the NAT null binding when creating new conntracks via
ctnetlink to avoid that several packets race at initializing the
the conntrack NAT extension, original patch from Florian Westphal,
revisited version from me.
* Fix DNAT handling in the snmp NAT helper, the same handling was being
done for SNAT and DNAT and 2.4 already contains that fix, from
Francois-Xavier Le Bail.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary helper function to send the New IRK mgmt
event and makes sure that the function is called at when SMP key
distribution has completed. The event is sent before the New LTK event
so user space knows which remote device to associate with the keys.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the SMP Long Term Key notification over mgmt from the
hci_add_ltk function to smp.c when both sides have completed their key
distribution. This way we are also able to update the identity address
into the mgmt_new_ltk event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As preparation to do mgmt notification in a single place at the end of
the key distribution, store the keys that need to be notified within the
SMP context.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It's simpler (one less if-statement) to just evaluate the appropriate
value for store_hint in the mgmt_new_ltk function than to pass a boolean
parameter to the function. Furthermore, this simplifies moving the mgmt
event emission out from hci_add_ltk in subsequent patches.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SMP code will need to postpone the mgmt event emission for the IRK
and LTKs. To avoid extra lookups at the end of the key distribution
simply return the added value from the add_ltk and add_irk functions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The various pieces of data cached in the hci_dev structure do not need
to be allocated using GFP_ATOMIC since they are never added from
interrupt context. This patch updates these allocations to use
GFP_KERNEL instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After processing hint_user, we would want to schedule the
timeout work only if we are actually waiting to CRDA. This happens
when the status is not "IGNORE" nor "ALREADY_SET".
Signed-off-by: Inbal Hacohen <Inbal.Hacohen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently cache socket policy bundles at xfrm_policy_sk_bundles.
These cached bundles are never used. Instead we create and cache
a new one whenever xfrm_lookup() is called on a socket policy.
Most protocols cache the used routes to the socket, so let's
remove the unused caching of socket policy bundles in xfrm.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
During LE connection establishment the value 0x0000 is used for min/max
connection event length. So use the same value when the peripheral is
requesting an update of the the connection paramters.
For some reason the value 0x0001 got used in the connection update and
0x0000 in the connection creation. Using the same value for both just
makes sense.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For debugging purposes expose the current list of identity resolving
keys via debugfs. This file is read-only and limited to root access.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the connection attempt fails, the address information are not
provided in the HCI_LE_Connection_Complete event. So use the original
information from the connection to reconstruct the identity address.
This is important when a connection attempt has been made using the
identity address, but the cached resolvable random address has changed
in the meantime. The failure event needs to use the identity address
and not the resolvable random address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When reporting connect failed events to userspace, use the address
of the connection and not the address from the HCI event.
This change is strictly speaking not needed since BR/EDR does not
have the concept of resolvable random addresses. It is more for
making the code consistent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the remote device has been successfully connected, report the
identity address (public address or static random address).
Currently the address from the HCI_LE_Connection_Complete event is
used. This was no problem so far, but since now known resolvable
random addresses are converted into identities, it is important to
use the identity of the connection and not the address report by
HCI event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull HID update from Jiri Kosina:
- fixes for several bugs in incorrect allocations of buffers by David
Herrmann and Benjamin Tissoires.
- support for a few new device IDs by Archana Patni, Benjamin
Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hyperv: make sure input buffer is big enough
HID: Bluetooth: hidp: make sure input buffers are big enough
HID: hid-sensor-hub: quirk for STM Sensor hub
HID: apple: add Apple wireless keyboard 2011 JIS model support
HID: fix buffer allocations
HID: multitouch: add FocalTech FTxxxx support
HID: microsoft: Add ID's for Surface Type/Touch Cover 2
HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay
The only place this is used outside rtnetlink.c is veth. So provide
wrapper function for this usage.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's slightly smaller/faster for some architectures.
Make sure def_multicast_addr is __aligned(2)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These include are here since kernel 2.2.7, but probably never used.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_set_csma_params has a redundant (and impossible) check for
"retries", found by smatch. The check was supposed to be for
frame_retries, but wasn't moved during development when
phy_set_frame_retries was introduced. Also, maxBE >= 3 as required by
the standard is not enforced.
Remove the redundant check, assure max_be >= 3 and check -1 <=
frame_retries <= 7 in the correct function.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
At first glance it looks like there is a missing curly brace but
actually the code works the same either way. I have adjusted the
indenting but left the code the same.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the following functions, which are shorter and more in line
with common naming practice in the network subsystem.
tipc_bclink_send_msg->tipc_bclink_xmit
tipc_bclink_recv_pkt->tipc_bclink_rcv
tipc_disc_recv_msg->tipc_disc_rcv
tipc_link_send_proto_msg->tipc_link_proto_xmit
link_recv_proto_msg->tipc_link_proto_rcv
link_send_sections_long->tipc_link_iovec_long_xmit
tipc_link_send_sections_fast->tipc_link_iovec_xmit_fast
tipc_link_send_sync->tipc_link_sync_xmit
tipc_link_recv_sync->tipc_link_sync_rcv
tipc_link_send_buf->__tipc_link_xmit
tipc_link_send->tipc_link_xmit
tipc_link_send_names->tipc_link_names_xmit
tipc_named_recv->tipc_named_rcv
tipc_link_recv_bundle->tipc_link_bundle_rcv
tipc_link_dup_send_queue->tipc_link_dup_queue_xmit
link_send_long_buf->tipc_link_frag_xmit
tipc_multicast->tipc_port_mcast_xmit
tipc_port_recv_mcast->tipc_port_mcast_rcv
tipc_port_reject_sections->tipc_port_iovec_reject
tipc_port_recv_proto_msg->tipc_port_proto_rcv
tipc_connect->tipc_port_connect
__tipc_connect->__tipc_port_connect
__tipc_disconnect->__tipc_port_disconnect
tipc_disconnect->tipc_port_disconnect
tipc_shutdown->tipc_port_shutdown
tipc_port_recv_msg->tipc_port_rcv
tipc_port_recv_sections->tipc_port_iovec_rcv
release->tipc_release
accept->tipc_accept
bind->tipc_bind
get_name->tipc_getname
poll->tipc_poll
send_msg->tipc_sendmsg
send_packet->tipc_send_packet
send_stream->tipc_send_stream
recv_msg->tipc_recvmsg
recv_stream->tipc_recv_stream
connect->tipc_connect
listen->tipc_listen
shutdown->tipc_shutdown
setsockopt->tipc_setsockopt
getsockopt->tipc_getsockopt
Above changes have no impact on current users of the functions.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP's sctp_connectx() abi breaks for 64bit kernels compiled with 32bit
emulation (e.g. ia32 emulation or x86_x32). Due to internal usage of
'struct sctp_getaddrs_old' which includes a struct sockaddr pointer,
sizeof(param) check will always fail in kernel as the structure in
64bit kernel space is 4bytes larger than for user binaries compiled
in 32bit mode. Thus, applications making use of sctp_connectx() won't
be able to run under such circumstances.
Introduce a compat interface in the kernel to deal with such
situations by using a 'struct compat_sctp_getaddrs_old' structure
where user data is copied into it, and then sucessively transformed
into a 'struct sctp_getaddrs_old' structure with the help of
compat_ptr(). That fixes sctp_connectx() abi without any changes
needed in user space, and lets the SCTP test suite pass when compiled
in 32bit and run on 64bit kernels.
Fixes: f9c67811eb ("sctp: Fix regression introduced by new sctp_connectx api")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix soft-interface MTU computation
- fix bogus pointer mangling when parsing the TT-TVLV
container. This bug led to a wrong memory access.
- fix memory leak by properly releasing the VLAN object
after CRC check
- properly check pskb_may_pull() return value
- avoid potential race condition while adding new neighbour
- fix potential memory leak by removing all the references
to the orig_node object in case of initialization failure
- fix the TT CRC computation by ensuring that every node uses
the same byte order when hosts with different endianess are
part of the same network
- fix severe memory leak by freeing skb after a successful
TVLV parsing
- avoid potential double free when orig_node initialization
fails
- fix potential kernel paging error caused by the usage of
the old value of skb->data after skb reallocation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=6IO8
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- fix soft-interface MTU computation
- fix bogus pointer mangling when parsing the TT-TVLV
container. This bug led to a wrong memory access.
- fix memory leak by properly releasing the VLAN object
after CRC check
- properly check pskb_may_pull() return value
- avoid potential race condition while adding new neighbour
- fix potential memory leak by removing all the references
to the orig_node object in case of initialization failure
- fix the TT CRC computation by ensuring that every node uses
the same byte order when hosts with different endianess are
part of the same network
- fix severe memory leak by freeing skb after a successful
TVLV parsing
- avoid potential double free when orig_node initialization
fails
- fix potential kernel paging error caused by the usage of
the old value of skb->data after skb reallocation
Signed-off-by: David S. Miller <davem@davemloft.net>
Silently dropping L2CAP data (i.e. due to remote device not obeying
negotiated MTU) is confusing and makes debugging harder.
Signed-off-by: Szymon Janc <szymon.janc@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Whenever a device uses an RPA we want to have user space identify it by
its Identity Address if we've got an IRK available for it. This patch
updates the Device Found mgmt event to contain the Identity Address if
an IRK is available for the device in question.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need to check whether there's a matching IRK and RPA when we're
requested to connect to a remote LE device based on its Identity
Address. This patch updates the hci_connect_le function to do an extra
call to hci_find_irk_by_addr and uses the RPA if it's cached. This is
particularly important once we start exposing the Identity Address to
user space instead of the RPA in events such as Device Connected and
Device Found.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Identity Addresses are either public or static random. When looking up
addresses based on the Identity Address it doesn't make sense to go
through the IRK list if we're given a private random address. This patch
fixes (or rather improves) the hci_find_irk_by_addr function to bail out
early if given a private random address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we initiate pairing through mgmt_pair_device the code has so far
been waiting for a successful HCI Encrypt Change event in order to
respond to the mgmt command. However, putting privacy into the play we
actually want the key distribution to be complete before replying so
that we can include the Identity Address in the mgmt response.
This patch updates the various hci_conn callbacks for LE in mgmt.c to
only respond in the case of failure, and adds a new mgmt_smp_complete
function that the SMP code will call once key distribution has been
completed.
Since the smp_chan_destroy function that's used to indicate completion
and clean up the SMP context can be called from various places,
including outside of smp.c, the easiest way to track failure vs success
is a new flag that we set once key distribution has been successfully
completed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we receive a remote identity address during SMP key distribution we
should ensure that any associated L2CAP channel instances get their
address information correspondingly updated (so that e.g. doing
getpeername on associated sockets returns the correct address).
This patch adds a new L2CAP core function l2cap_conn_update_id_addr()
which is used to iterate through all L2CAP channels associated with a
connection and update their address information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we want user space to see and use the LE Identity Address whenever
interfacing with the kernel it makes sense to track that instead of the
real address (the two will only be different in the case of an RPA).
This patch adds the necessary updates to when an LE connection gets
established and when receiving the Identity Address from a remote
device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that each HCI device has its own AES crypto context we don't need
the one stored in the SMP data any more. This patch removes the variable
from struct smp_chan and updates the SMP code to use the per-hdev crypto
context.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When mgmt_unpair_device is called we should also remove any associated
IRKs. This patch adds a hci_remove_irk convenience function and ensures
that it's called when mgmt_unpair_device is called.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're the acceptors (peripheral/slave) of an SMP procedure and
we've completed distributing our keys we should only stick around
waiting for keys from the remote side if any of the initiator
distribution bits were actually set. This patch fixes the
smp_distribute_keys function to clear the SMP context when this
situation occurs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is code (in mgmt.c) that depends on the hci_remove_ltk function to
fail if no match is found. This patch adds tracking of removed LTKs
(there can be up to two: one for master and another for slave) in the
hci_remove_ltk function and returns -ENOENT of no matches were found.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are many functions that never fail but still declare an integer
return value for no reason. This patch converts these functions to use a
void return value to avoid any confusion of whether they can fail or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When removing Long Term Keys we should also be checking that the given
address type (public vs random) matches. This patch updates the
hci_remove_ltk function to take an extra parameter and uses it for
address type matching.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we didn't request certain pieces of information during the key
distribution negotiation we should properly ignore those PDUs if the
peer incorrectly sends them. This includes the Encryption Information
and Master Identification PDUs if the EncKey bit was not set, and the
Identity Information and Identity Address Information PDUs if the IdKey
bit was not set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch does the necessary changes to request the remote device to
distribute its IRK to us during the SMP pairing procedure. This includes
setting the right key distribution values in the pairing
request/response and handling of the two related SMP PDUs, i.e. Identity
Information and Identity Address Information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the Load IRKs command for the management
interface. The command is used to load the kernel with the initial set
of IRKs. It also sets a HCI_RPA_RESOLVING flag to indicate that we can
start requesting devices to distribute their IRK to us.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the initial IRK storage and management functions to the
HCI core. This includes storing a list of IRKs per HCI device and the
ability to add, remove and lookup entries in that list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previously the crypto context has only been available for LE SMP
sessions, but now that we'll need to perform operations also during
discovery it makes sense to have this context part of the hci_dev
struct. Later, the context can be removed from the SMP context.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a helper function to check whether a given IRK matches a
given Resolvable Private Address (RPA). The function will be needed for
implementing the rest of address resolving support.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes a couple of unnecessary empty lines in the SMP code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For each received SMP PDU we need to check that we have enough data to
fit the specified size of the PDU. This patch adds the necessary checks
for each SMP PDU handler and ensures that buffer overflows do not occur
if to little data has been received.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Quoting Andrey Vagin:
When a conntrack is created by kernel, it is initialized (sets
IPS_{DST,SRC}_NAT_DONE_BIT bits in nf_nat_setup_info) and only then it
is added in hashes (__nf_conntrack_hash_insert), so one conntract
can't be initialized from a few threads concurrently.
ctnetlink can add an uninitialized conntrack (w/o
IPS_{DST,SRC}_NAT_DONE_BIT) in hashes, then a few threads can look up
this conntrack and start initialize it concurrently. It's dangerous,
because BUG can be triggered from nf_nat_setup_info.
Fix this race by always setting up nat, even if no CTA_NAT_ attribute
was requested before inserting the ct into the hash table. In absence
of CTA_NAT_ attribute, a null binding is created.
This alters current behaviour: Before this patch, the first packet
matching the newly injected conntrack would be run through the nat
table since nf_nat_initialized() returns false. IOW, this forces
ctnetlink users to specify the desired nat transformation on ct
creation time.
Thanks for Florian Westphal, this patch is based on his original
patch to address this problem, including this patch description.
Reported-By: Andrey Vagin <avagin@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Florian Westphal <fw@strlen.de>
ERROR: spaces required and "(foo*)" should be "(foo *)"
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace two magic numbers which intialize clgstate::state.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit 89aef8921bf("ipv4: Delete routing cache."), the counter
in_slow_tot can't work correctly.
The counter in_slow_tot increase by one when fib_lookup() return successfully
in ip_route_input_slow(), but actually the dst struct maybe not be created and
cached, so we can increase in_slow_tot after the dst struct is created.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new netlink attributes for SET_PHY_ATTRS:
* CSMA minimal backoff exponent
* CSMA maximal backoff exponent
* CSMA retry limit
* frame retransmission limit
The CSMA attributes shall correspond to minBE, maxBE and maxCSMABackoffs of
802.15.4, respectively. The frame retransmission shall correspond to
maxFrameRetries of 802.15.4, unless given as -1: then the old behaviour
of the stack shall apply. For RF2xy, the old behaviour is to not do
channel sensing at all and simply send *right now*, which is not
intended behaviour for most applications and actually prohibited for
some channel/page combinations.
For all values except frame retransmission limit, the defaults of
802.15.4 apply. Frame retransmission limits are set to -1 to indicate
backward-compatible behaviour.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since three of the four clear channel assesment modes make use of energy
detection, provide an API to set the energy detection threshold.
Driver support for this is available in at86rf230 for the RF212 chips.
Since for these chips the minimal energy detection threshold depends on
page and channel used, add a field to struct at86rf230_local that stores
the minimal threshold. Actual ED thresholds are configured as offsets
from this value.
For RF212, setting the ED threshold will not work before a channel/page
has been set due to the dependency of energy detection in the chip and
the actual channel/page selected.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard describes four modes of clear channel assesment: "energy
above threshold", "carrier found", and the logical and/or of these two.
Support for CCA mode setting is included in the at86rf230 driver,
predicated for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Listen-before-talk is an alternative to CSMA in uncoordinated networks
and prescribed by european regulations if one wants to have a device
with radio duty cycles above 10% (or less in some bands). Add a phy
property to enable/disable LBT in the phy, including support in the
at86rf230 driver for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.
This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
HID core expects the input buffers to be at least of size 4096
(HID_MAX_BUFFER_SIZE). Other sizes will result in buffer-overflows if an
input-report is smaller than advertised. We could, like i2c, compute the
biggest report-size instead of using HID_MAX_BUFFER_SIZE, but this will
blow up if report-descriptors are changed after ->start() has been called.
So lets be safe and just use the biggest buffer we have.
Note that this adds an additional copy to the HIDP input path. If there is
a way to make sure the skb-buf is big enough, we should use that instead.
The best way would be to make hid-core honor the @size argument, though,
that sounds easier than it is. So lets just fix the buffer-overflows for
now and afterwards look for a faster way for all transport drivers.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This bug was reported by Steinar H. Gunderson and was introduced by commit
f7cb888633 ("sit/gre6: don't try to add the same route two times").
root@morgental:~# ip tunnel add foo mode gre remote 1.2.3.4 ttl 64
root@morgental:~# ip link set foo up mtu 1468
root@morgental:~# ip -6 route show dev foo
fe80::/64 proto kernel metric 256
but after the above commit, no such route shows up.
There is no link local route because dev->dev_addr is 0 (because local ipv4
address is 0), hence no link local address is configured.
In this scenario, the link local address is added manually: 'ip -6 addr add
fe80::1 dev foo' and because prefix is /128, no link local route is added by the
kernel.
Even if the right things to do is to add the link local address with a /64
prefix, we need to restore the previous behavior to avoid breaking userpace.
Reported-by: Steinar H. Gunderson <sesse@samfundet.no>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to setup HCI User Channel usage for LE only controllers without
a public address or configured static address will fail with an error
saying that no address is available.
In case of HCI User Channel the requirement for a valid address is not
needed. So allow skipping this extra validation step.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the setup of user channel fails, the index added event is not sent
and will cause issues with user interaction. This problem can be easily
triggered with a LE only controller without a public address. In that
case hci_dev_open() fails and that error case is not sending an event
saying that the controller is available for normal use again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
batadv_send_skb_prepare_unicast(_4addr) might reallocate the
skb's data. If it does then our ethhdr pointer is not valid
anymore in batadv_send_skb_unicast(), resulting in a kernel
paging error.
Fixing this by refetching the ethhdr pointer after the
potential reallocation.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
In the failure path of the orig_node initialization routine
the orig_node->bat_iv.bcast_own field is free'd twice: first
in batadv_iv_ogm_orig_get() and then later in
batadv_orig_node_free_rcu().
Fix it by removing the kfree in batadv_iv_ogm_orig_get().
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
When the TVLV parsing routine succeed the skb is left
untouched thus leading to a memory leak.
Fix this by consuming the skb in case of success.
Introduced by ef26157747
("batman-adv: tvlv - basic infrastructure")
Reported-by: Russel Senior <russell@personaltelco.net>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Tested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
When computing the CRC on a 2byte variable the order of
the bytes obviously alters the final result. This means
that computing the CRC over the same value on two archs
having different endianess leads to different numbers.
The global and local translation table CRC computation
routine makes this mistake while processing the clients
VIDs. The result is a continuous CRC mismatching between
nodes having different endianess.
Fix this by converting the VID to Network Order before
processing it. This guarantees that every node uses the same
byte order.
Introduced by 7ea7b4a142
("batman-adv: make the TT CRC logic VLAN specific")
Reported-by: Russel Senior <russell@personaltelco.net>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Tested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Since batadv_orig_node_new() sets the refcount to two, assuming that
the calling function will use a reference for putting the orig_node into
a hash or similar, both references must be freed if initialization of
the orig_node fails. Otherwise that object may be leaked in that error
case.
Reported-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
When adding a new neighbour it is important to atomically
perform the following:
- check if the neighbour already exists
- append the neighbour to the proper list
If the two operations are not performed in an atomic context
it is possible that two concurrent insertions add the same
neighbour twice.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
pskb_may_pull() returns 1 on success and 0 in case of failure,
therefore checking for the return value being negative does
not make sense at all.
This way if the function fails we will probably read beyond the current
skb data buffer. Fix this by doing the proper check.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
There is a refcounter unbalance in the CRC checking routine
invoked on OGM reception. A vlan object is retrieved (thus
its refcounter is increased by one) but it is never properly
released. This leads to a memleak because the vlan object
will never be free'd.
Fix this by releasing the vlan object after having read the
CRC.
Reported-by: Russell Senior <russell@personaltelco.net>
Reported-by: Daniel <daniel@makrotopia.org>
Reported-by: cmsv <cmsv@wirelesspt.net>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
When accessing a TT-TVLV container in the OGM RX path
the variable pointing to the list of changes to apply is
altered by mistake.
This makes the TT component read data at the wrong position
in the OGM packet buffer.
Fix it by removing the bogus pointer alteration.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The current MTU computation always returns a value
smaller than 1500bytes even if the real interfaces
have an MTU large enough to compensate the batman-adv
overhead.
Fix the computation by properly returning the highest
admitted value.
Introduced by a19d3d85e1
("batman-adv: limit local translation table max size")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The long term keys should only be stored when they belong to an
indentity address. The identity address can either be a public
address or a random static address.
For all other addresses (unresovable or resolvable) tell userspace
that the long term key is not persistent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The long term keys should be associated with an identity address. Valid
identity addresses are public addresses or static addresses. So only
allow these two as valid address information for long term keys.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add a check if payload's length is a power of 2 when selecting ops.
The fast ops were meant for well aligned loads, also this fixes a
small bug when using a length of 3 with some offsets which causes
only 1 byte to be loaded because the fast ops are chosen.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When using nftables with CONFIG_NETFILTER_XT_TARGET_TRACE=n, we get
lots of "TRACE: filter:output:policy:1 IN=..." warnings as several
places will leave skb->nf_trace uninitialised.
Unlike iptables tracing functionality is not conditional in nftables,
so always copy/zero nf_trace setting when nftables is enabled.
Move this into __nf_copy() helper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The goal of this patch is to allow userland to dump only a part of SA by
specifying a filter during the dump.
The kernel is in charge to filter SA, this avoids to generate useless netlink
traffic (it save also some cpu cycles). This is particularly useful when there
is a big number of SA set on the system.
Note that I removed the union in struct xfrm_state_walk to fix a problem on arm.
struct netlink_callback->args is defined as a array of 6 long and the first long
is used in xfrm code to flag the cb as initialized. Hence, we must have:
sizeof(struct xfrm_state_walk) <= sizeof(long) * 5.
With the union, it was false on arm (sizeof(struct xfrm_state_walk) was
sizeof(long) * 7), due to the padding.
In fact, whatever the arch is, this union seems useless, there will be always
padding after it. Removing it will not increase the size of this struct (and
reduce it on arm).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Mathias reported that on an AMD Geode LX embedded board (ALiX)
with ath9k driver PACKET_QDISC_BYPASS, introduced in commit
d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket
option"), triggers a WARN_ON() coming from the driver itself
via 066dae93bd ("ath9k: rework tx queue selection and fix
queue stopping/waking").
The reason why this happened is that ndo_select_queue() call
is not invoked from direct xmit path i.e. for ieee80211 subsystem
that sets queue and TID (similar to 802.1d tag) which is being
put into the frame through 802.11e (WMM, QoS). If that is not
set, pending frame counter for e.g. ath9k can get messed up.
So the WARN_ON() in ath9k is absolutely legitimate. Generally,
the hw queue selection in ieee80211 depends on the type of
traffic, and priorities are set according to ieee80211_ac_numbers
mapping; working in a similar way as DiffServ only on a lower
layer, so that the AP can favour frames that have "real-time"
requirements like voice or video data frames.
Therefore, check for presence of ndo_select_queue() in netdev
ops and, if available, invoke it with a fallback handler to
__packet_pick_tx_queue(), so that driver such as bnx2x, ixgbe,
or mlx4 can still select a hw queue for transmission in
relation to the current CPU while e.g. ieee80211 subsystem
can make their own choices.
Reported-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow users to invoke netdev_cap_txqueue, it needs to
be moved into netdevice.h header file. While at it, also add kernel
doc header to document the API.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I commit e099e86c9e
("tipc: add node_lock protection to link lookup function")
we are calling spin_lock(&node->lock) directly instead of indirectly
via the tipc_node_lock(node) function. However, tipc_node_lock() is
using spin_lock_bh(), not spin_lock(), something leading to
unbalanced usage in one place, and a smatch warning.
We fix this by consistently using tipc_node_lock()/unlock() in
in the places touched by the mentioned commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 7d33939f47
("tipc: delay delete of link when failover is needed") we
introduced a loop for finding and removing a link pointer
in an array. The removal is done after we have left the loop,
giving the impression that one may remove the wrong pointer
if no matching element is found.
This is not really a bug, since we know that there will always
be a matching element, but it looks wrong, and causes a smatch
warning.
We fix this loop with this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementation of (a)rwnd calculation might lead to severe performance issues
and associations completely stalling. These problems are described and solution
is proposed which improves lksctp's robustness in congestion state.
1) Sudden drop of a_rwnd and incomplete window recovery afterwards
Data accounted in sctp_assoc_rwnd_decrease takes only payload size (sctp data),
but size of sk_buff, which is blamed against receiver buffer, is not accounted
in rwnd. Theoretically, this should not be the problem as actual size of buffer
is double the amount requested on the socket (SO_RECVBUF). Problem here is
that this will have bad scaling for data which is less then sizeof sk_buff.
E.g. in 4G (LTE) networks, link interfacing radio side will have a large portion
of traffic of this size (less then 100B).
An example of sudden drop and incomplete window recovery is given below. Node B
exhibits problematic behavior. Node A initiates association and B is configured
to advertise rwnd of 10000. A sends messages of size 43B (size of typical sctp
message in 4G (LTE) network). On B data is left in buffer by not reading socket
in userspace.
Lets examine when we will hit pressure state and declare rwnd to be 0 for
scenario with above stated parameters (rwnd == 10000, chunk size == 43, each
chunk is sent in separate sctp packet)
Logic is implemented in sctp_assoc_rwnd_decrease:
socket_buffer (see below) is maximum size which can be held in socket buffer
(sk_rcvbuf). current_alloced is amount of data currently allocated (rx_count)
A simple expression is given for which it will be examined after how many
packets for above stated parameters we enter pressure state:
We start by condition which has to be met in order to enter pressure state:
socket_buffer < currently_alloced;
currently_alloced is represented as size of sctp packets received so far and not
yet delivered to userspace. x is the number of chunks/packets (since there is no
bundling, and each chunk is delivered in separate packet, we can observe each
chunk also as sctp packet, and what is important here, having its own sk_buff):
socket_buffer < x*each_sctp_packet;
each_sctp_packet is sctp chunk size + sizeof(struct sk_buff). socket_buffer is
twice the amount of initially requested size of socket buffer, which is in case
of sctp, twice the a_rwnd requested:
2*rwnd < x*(payload+sizeof(struc sk_buff));
sizeof(struct sk_buff) is 190 (3.13.0-rc4+). Above is stated that rwnd is 10000
and each payload size is 43
20000 < x(43+190);
x > 20000/233;
x ~> 84;
After ~84 messages, pressure state is entered and 0 rwnd is advertised while
received 84*43B ~= 3612B sctp data. This is why external observer notices sudden
drop from 6474 to 0, as it will be now shown in example:
IP A.34340 > B.12345: sctp (1) [INIT] [init tag: 1875509148] [rwnd: 81920] [OS: 10] [MIS: 65535] [init TSN: 1096057017]
IP B.12345 > A.34340: sctp (1) [INIT ACK] [init tag: 3198966556] [rwnd: 10000] [OS: 10] [MIS: 10] [init TSN: 902132839]
IP A.34340 > B.12345: sctp (1) [COOKIE ECHO]
IP B.12345 > A.34340: sctp (1) [COOKIE ACK]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057017] [SID: 0] [SSEQ 0] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057017] [a_rwnd 9957] [#gap acks 0] [#dup tsns 0]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057018] [SID: 0] [SSEQ 1] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057018] [a_rwnd 9957] [#gap acks 0] [#dup tsns 0]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057019] [SID: 0] [SSEQ 2] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057019] [a_rwnd 9914] [#gap acks 0] [#dup tsns 0]
<...>
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057098] [SID: 0] [SSEQ 81] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057098] [a_rwnd 6517] [#gap acks 0] [#dup tsns 0]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057099] [SID: 0] [SSEQ 82] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057099] [a_rwnd 6474] [#gap acks 0] [#dup tsns 0]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057100] [SID: 0] [SSEQ 83] [PPID 0x18]
--> Sudden drop
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057100] [a_rwnd 0] [#gap acks 0] [#dup tsns 0]
At this point, rwnd_press stores current rwnd value so it can be later restored
in sctp_assoc_rwnd_increase. This however doesn't happen as condition to start
slowly increasing rwnd until rwnd_press is returned to rwnd is never met. This
condition is not met since rwnd, after it hit 0, must first reach rwnd_press by
adding amount which is read from userspace. Let us observe values in above
example. Initial a_rwnd is 10000, pressure was hit when rwnd was ~6500 and the
amount of actual sctp data currently waiting to be delivered to userspace
is ~3500. When userspace starts to read, sctp_assoc_rwnd_increase will be blamed
only for sctp data, which is ~3500. Condition is never met, and when userspace
reads all data, rwnd stays on 3569.
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057100] [a_rwnd 1505] [#gap acks 0] [#dup tsns 0]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057100] [a_rwnd 3010] [#gap acks 0] [#dup tsns 0]
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057101] [SID: 0] [SSEQ 84] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057101] [a_rwnd 3569] [#gap acks 0] [#dup tsns 0]
--> At this point userspace read everything, rwnd recovered only to 3569
IP A.34340 > B.12345: sctp (1) [DATA] (B)(E) [TSN: 1096057102] [SID: 0] [SSEQ 85] [PPID 0x18]
IP B.12345 > A.34340: sctp (1) [SACK] [cum ack 1096057102] [a_rwnd 3569] [#gap acks 0] [#dup tsns 0]
Reproduction is straight forward, it is enough for sender to send packets of
size less then sizeof(struct sk_buff) and receiver keeping them in its buffers.
2) Minute size window for associations sharing the same socket buffer
In case multiple associations share the same socket, and same socket buffer
(sctp.rcvbuf_policy == 0), different scenarios exist in which congestion on one
of the associations can permanently drop rwnd of other association(s).
Situation will be typically observed as one association suddenly having rwnd
dropped to size of last packet received and never recovering beyond that point.
Different scenarios will lead to it, but all have in common that one of the
associations (let it be association from 1)) nearly depleted socket buffer, and
the other association blames socket buffer just for the amount enough to start
the pressure. This association will enter pressure state, set rwnd_press and
announce 0 rwnd.
When data is read by userspace, similar situation as in 1) will occur, rwnd will
increase just for the size read by userspace but rwnd_press will be high enough
so that association doesn't have enough credit to reach rwnd_press and restore
to previous state. This case is special case of 1), being worse as there is, in
the worst case, only one packet in buffer for which size rwnd will be increased.
Consequence is association which has very low maximum rwnd ('minute size', in
our case down to 43B - size of packet which caused pressure) and as such
unusable.
Scenario happened in the field and labs frequently after congestion state (link
breaks, different probabilities of packet drop, packet reordering) and with
scenario 1) preceding. Here is given a deterministic scenario for reproduction:
>From node A establish two associations on the same socket, with rcvbuf_policy
being set to share one common buffer (sctp.rcvbuf_policy == 0). On association 1
repeat scenario from 1), that is, bring it down to 0 and restore up. Observe
scenario 1). Use small payload size (here we use 43). Once rwnd is 'recovered',
bring it down close to 0, as in just one more packet would close it. This has as
a consequence that association number 2 is able to receive (at least) one more
packet which will bring it in pressure state. E.g. if association 2 had rwnd of
10000, packet received was 43, and we enter at this point into pressure,
rwnd_press will have 9957. Once payload is delivered to userspace, rwnd will
increase for 43, but conditions to restore rwnd to original state, just as in
1), will never be satisfied.
--> Association 1, between A.y and B.12345
IP A.55915 > B.12345: sctp (1) [INIT] [init tag: 836880897] [rwnd: 10000] [OS: 10] [MIS: 65535] [init TSN: 4032536569]
IP B.12345 > A.55915: sctp (1) [INIT ACK] [init tag: 2873310749] [rwnd: 81920] [OS: 10] [MIS: 10] [init TSN: 3799315613]
IP A.55915 > B.12345: sctp (1) [COOKIE ECHO]
IP B.12345 > A.55915: sctp (1) [COOKIE ACK]
--> Association 2, between A.z and B.12346
IP A.55915 > B.12346: sctp (1) [INIT] [init tag: 534798321] [rwnd: 10000] [OS: 10] [MIS: 65535] [init TSN: 2099285173]
IP B.12346 > A.55915: sctp (1) [INIT ACK] [init tag: 516668823] [rwnd: 81920] [OS: 10] [MIS: 10] [init TSN: 3676403240]
IP A.55915 > B.12346: sctp (1) [COOKIE ECHO]
IP B.12346 > A.55915: sctp (1) [COOKIE ACK]
--> Deplete socket buffer by sending messages of size 43B over association 1
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315613] [SID: 0] [SSEQ 0] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315613] [a_rwnd 9957] [#gap acks 0] [#dup tsns 0]
<...>
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315696] [a_rwnd 6388] [#gap acks 0] [#dup tsns 0]
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315697] [SID: 0] [SSEQ 84] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315697] [a_rwnd 6345] [#gap acks 0] [#dup tsns 0]
--> Sudden drop on 1
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315698] [SID: 0] [SSEQ 85] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315698] [a_rwnd 0] [#gap acks 0] [#dup tsns 0]
--> Here userspace read, rwnd 'recovered' to 3698, now deplete again using
association 1 so there is place in buffer for only one more packet
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315799] [SID: 0] [SSEQ 186] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315799] [a_rwnd 86] [#gap acks 0] [#dup tsns 0]
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315800] [SID: 0] [SSEQ 187] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315800] [a_rwnd 43] [#gap acks 0] [#dup tsns 0]
--> Socket buffer is almost depleted, but there is space for one more packet,
send them over association 2, size 43B
IP B.12346 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3676403240] [SID: 0] [SSEQ 0] [PPID 0x18]
IP A.55915 > B.12346: sctp (1) [SACK] [cum ack 3676403240] [a_rwnd 0] [#gap acks 0] [#dup tsns 0]
--> Immediate drop
IP A.60995 > B.12346: sctp (1) [SACK] [cum ack 387491510] [a_rwnd 0] [#gap acks 0] [#dup tsns 0]
--> Read everything from the socket, both association recover up to maximum rwnd
they are capable of reaching, note that association 1 recovered up to 3698,
and association 2 recovered only to 43
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315800] [a_rwnd 1548] [#gap acks 0] [#dup tsns 0]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315800] [a_rwnd 3053] [#gap acks 0] [#dup tsns 0]
IP B.12345 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3799315801] [SID: 0] [SSEQ 188] [PPID 0x18]
IP A.55915 > B.12345: sctp (1) [SACK] [cum ack 3799315801] [a_rwnd 3698] [#gap acks 0] [#dup tsns 0]
IP B.12346 > A.55915: sctp (1) [DATA] (B)(E) [TSN: 3676403241] [SID: 0] [SSEQ 1] [PPID 0x18]
IP A.55915 > B.12346: sctp (1) [SACK] [cum ack 3676403241] [a_rwnd 43] [#gap acks 0] [#dup tsns 0]
A careful reader might wonder why it is necessary to reproduce 1) prior
reproduction of 2). It is simply easier to observe when to send packet over
association 2 which will push association into the pressure state.
Proposed solution:
Both problems share the same root cause, and that is improper scaling of socket
buffer with rwnd. Solution in which sizeof(sk_buff) is taken into concern while
calculating rwnd is not possible due to fact that there is no linear
relationship between amount of data blamed in increase/decrease with IP packet
in which payload arrived. Even in case such solution would be followed,
complexity of the code would increase. Due to nature of current rwnd handling,
slow increase (in sctp_assoc_rwnd_increase) of rwnd after pressure state is
entered is rationale, but it gives false representation to the sender of current
buffer space. Furthermore, it implements additional congestion control mechanism
which is defined on implementation, and not on standard basis.
Proposed solution simplifies whole algorithm having on mind definition from rfc:
o Receiver Window (rwnd): This gives the sender an indication of the space
available in the receiver's inbound buffer.
Core of the proposed solution is given with these lines:
sctp_assoc_rwnd_update:
if ((asoc->base.sk->sk_rcvbuf - rx_count) > 0)
asoc->rwnd = (asoc->base.sk->sk_rcvbuf - rx_count) >> 1;
else
asoc->rwnd = 0;
We advertise to sender (half of) actual space we have. Half is in the braces
depending whether you would like to observe size of socket buffer as SO_RECVBUF
or twice the amount, i.e. size is the one visible from userspace, that is,
from kernelspace.
In this way sender is given with good approximation of our buffer space,
regardless of the buffer policy - we always advertise what we have. Proposed
solution fixes described problems and removes necessity for rwnd restoration
algorithm. Finally, as proposed solution is simplification, some lines of code,
along with some bytes in struct sctp_association are saved.
Version 2 of the patch addressed comments from Vlad. Name of the function is set
to be more descriptive, and two parts of code are changed, in one removing the
superfluous call to sctp_assoc_rwnd_update since call would not result in update
of rwnd, and the other being reordering of the code in a way that call to
sctp_assoc_rwnd_update updates rwnd. Version 3 corrected change introduced in v2
in a way that existing function is not reordered/copied in line, but it is
correctly called. Thanks Vlad for suggesting.
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this always returns ENOBUFS, because the return value of
__ip_tunnel_create is discarded.
A more common failure is a duplicate name (EEXIST). Propagate the real
error code so userspace can display a more meaningful error message.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit 251da413("ipv4: Cache ip_error() routes even when not forwarding."),
the counter IPSTATS_MIB_INADDRERRORS can't work correctly, because the value of
err was always set to ENETUNREACH.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dccp tfrc: revert
This reverts 6aee49c558 ("dccp: make local variable static") since
the variable tfrc_debug is referenced by the tfrc_pr_debug(fmt, ...)
macro when TFRC debugging is enabled. If it is enabled, use of the
macro produces a compilation error.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In gss_alloc_msg(), if the call to gss_encode_v1_msg() fails, we
want to release the reference to the pipe_version that was obtained
earlier in the function.
Fixes: 9d3a2260f0 (SUNRPC: Fix buffer overflow checking in...)
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Fix a race in which the RPC client is shutting down while the
gss daemon is processing a downcall. If the RPC client manages to
shut down before the gss daemon is done, then the struct gss_auth
used in gss_release_msg() may have already been freed.
Link: http://lkml.kernel.org/r/1392494917.71728.YahooMailNeo@web140002.mail.bf1.yahoo.com
Reported-by: John <da_audiophile@yahoo.com>
Reported-by: Borislav Petkov <bp@alien8.de>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Openvswitch defines u64_stats_sync as ->sync rather than ->syncp,
so fails to compile with netdev_alloc_pcpu_stats(). So just rename it to ->syncp.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 1c213bd24a (net: introduce netdev_alloc_pcpu_stats() for drivers)
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb truesize of a 12-byte payload with a 10-byte head/tail
reserve is 768 bytes. Consequently, even with 40 tx_credits, at
most 6 packets could be queued at any one time:
40 tx_credits * 127-byte mtu < 768-byte truesize * 7
This error could also cause the tx queue to apparently stall if
credit flow control is disabled (where tx_credits is fixed at 5),
or if the receiver only granted a limited number of tx credits
(eg., less than 7).
Instead, track the outstanding number of queued packets not yet sent
in wmem_alloc and allow for a maximum of 40 queued packets. Report
the space avail for a single write() as the mtu * number of packets
left before reaching the maximum.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Compute the amount of space available for a single write()
within rfcomm_room(); clamp to 0 for negative values. Note
this patch does not change the result of the computation.
Report the amount of room returned in the debug printk.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The tty driver api design prefers no-fail writes if the driver
write_room() method has previously indicated space is available
to accept writes. Since this is trivially possible for the
RFCOMM tty driver, do so.
Introduce rfcomm_dlc_send_noerror(), which queues but does not
schedule the krfcomm thread if the dlc is not yet connected
(and thus does not error based on the connection state).
The mtu size test is also unnecessary since the caller already
chunks the written data into mtu size.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If rfcomm_dlc_open() fails, set tty into error state which returns
-EIO from reads and writes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If RFCOMM tty device registration fails, cleanup by releasing
the tty_port reference to trigger rfcomm_dev destruction
(rather than open-coding it).
The dlc reference release is moved into rfcomm_dev_add(),
which ensures cleanup in both error paths -- ie., if
__rfcomm_dev_add() fails or if tty_port_register_device() fails.
Fixes releasing the module reference if device registration fails.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move rfcomm_dev allocation and initialization into new function,
__rfcomm_dev_add(), to simplify resource release in error handling.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
At least two different race conditions exist with multiple concurrent
RFCOMMCREATEDEV and RFCOMMRELEASEDEV ioctls:
* Multiple concurrent RFCOMMCREATEDEVs with RFCOMM_REUSE_DLC can
mistakenly share the same DLC.
* RFCOMMRELEASEDEV can destruct the rfcomm_dev still being
constructed by RFCOMMCREATEDEV.
Introduce rfcomm_ioctl_mutex to serialize these add/remove operations.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Functions which search lists for matching id's are more
commonly named *_lookup, which is the convention in the
bluetooth core as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The RFCOMM tty device is parented to the acl link device when
the dlc state_change(BT_CONNECTED) notification is received.
However, if the dlc from the RFCOMM socket is being reused
(RFCOMM_REUSE_DLC is set), then the dlc may already be connected,
and no notification will occur.
Instead, always parent the RFCOMM tty device to the acl link
device at registration time. If the acl link device is not available
(eg, because the dlc is not connected) then the tty will remain
unparented until the BT_CONNECTED notification is received.
Fixes regression with ModemManager when the rfcomm device is
created with the flag RFCOMM_REUSE_DLC.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Accessing the results of hci_conn_hash_lookup_ba() is unsafe without
holding the hci_dev_lock() during the lookup. For example:
CPU 0 | CPU 1
hci_conn_hash_lookup_ba | hci_conn_del
rcu_read_lock | hci_conn_hash_del
list_for_each_entry_rcu | list_del_rcu
if (.....) | synchronize_rcu
rcu_read_unlock |
| hci_conn_del_sysfs
| hci_dev_put
| hci_conn_put
| put_device (last reference)
| bt_link_release
| kfree(conn)
return p << just freed |
Even if a hci_conn reference were taken (via hci_conn_get), would
not guarantee the lifetime of the sysfs device, but only safe
access to the in-memory structure.
Ensure the hci_conn device stays valid while the rfcomm device
is reparented; rename rfcomm_get_device() to rfcomm_reparent_device()
and perform the reparenting within the function while holding the
hci_dev_lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the RFCOMM session has not yet been started (ie., session is
still in BT_BOUND state) when a dlc is closed, directly close and
unlink the dlc rather than sending a DISC frame that is never
sent.
This allows the dlci to be immediately reused rather than waiting
for a 20 second timeout.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Prepare for directly closing dlc if the RFCOMM session has not
yet been started; refactor the dlc disconnect logic into a separate
local function, __rfcomm_dlc_disconn(). Retains functional
equivalence.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Prepare for directly closing dlc if the RFCOMM session has not
yet been started; refactor the deferred setup test for only those
dlc states to which the test applies. Retains functional
equivalence.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Merge conditional test for BT_LISTEN session state into following
switch statement (which is functionally equivalent).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only one session/channel combination may be in use at any one
time. However, the failure does not occur until the tty is
opened (in rfcomm_dlc_open()).
Because these settings are actually bound at rfcomm device
creation (via RFCOMMCREATEDEV ioctl), validate and fail before
creating the rfcomm tty device.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RFCOMM tty device teardown can race with new tty device registration
for the same device id:
CPU 0 | CPU 1
rfcomm_dev_add | rfcomm_dev_destruct
| spin_lock
| list_del <== dev_id no longer used
| spin_unlock
spin_lock | .
[search rfcomm_dev_list] | .
[dev_id not in use] | .
[initialize new rfcomm_dev] | .
spin_unlock | .
| .
tty_port_register_device | tty_unregister_device
Don't remove rfcomm_dev from the device list until after tty device
unregistration has completed.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When RFCOMM_RELEASE_ONHUP is set, the rfcomm tty driver 'takes over'
the initial rfcomm_dev reference created by the RFCOMMCREATEDEV ioctl.
The assumption is that the rfcomm tty driver will release the
rfcomm_dev reference when the tty is freed (in rfcomm_tty_cleanup()).
However, if the tty is never opened, the 'take over' never occurs,
so when RFCOMMRELEASEDEV ioctl is called, the reference is not
released.
Track the state of the reference 'take over' so that the release
is guaranteed by either the RFCOMMRELEASEDEV ioctl or the rfcomm tty
driver.
Note that the synchronous hangup in rfcomm_release_dev() ensures
that rfcomm_tty_install() cannot race with the RFCOMMRELEASEDEV ioctl.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
No logic prevents an rfcomm_dev from being released multiple
times. For example, if the rfcomm_dev ref count is large due
to pending tx, then multiple RFCOMMRELEASEDEV ioctls may
mistakenly release the rfcomm_dev too many times. Note that
concurrent ioctls are not required to create this condition.
Introduce RFCOMM_DEV_RELEASED status bit which guarantees the
rfcomm_dev can only be released once.
NB: Since the flags are exported to userspace, introduce the status
field to track state for which userspace should not be aware.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When enumerating RFCOMM devices in the rfcomm_dev_list, holding
the rfcomm_dev_lock only guarantees the existence of the enumerated
rfcomm_dev in memory, and not safe access to its state. Testing
the device state (such as RFCOMM_TTY_RELEASED) does not guarantee
the device will remain in that state for the subsequent access
to the rfcomm_dev's fields, nor guarantee that teardown has not
commenced.
Obtain an rfcomm_dev reference for the duration of rfcomm_dev
access.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
rfcomm_dev_get() can return a rfcomm_dev reference for a
device for which destruction may be commencing. This can happen
on tty destruction, which calls rfcomm_tty_cleanup(), the last
port reference may have been released but RFCOMM_TTY_RELEASED
was not set. The following race is also possible:
CPU 0 | CPU 1
| rfcomm_release_dev
rfcomm_dev_get | .
spin_lock | .
dev = __rfcomm_dev_get | .
if dev | .
if test_bit(TTY_RELEASED) | .
| !test_and_set_bit(TTY_RELEASED)
| tty_port_put <<<< last reference
else |
tty_port_get |
The reference acquire is bogus because destruction will commence
with the release of the last reference.
Ignore the external state change of TTY_RELEASED and instead rely
on the reference acquire itself to determine if the reference is
valid.
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit e228b63390.
This is the third of a 3-patch revert, together with
Revert "Bluetooth: Remove rfcomm_carrier_raised()" and
Revert "Bluetooth: Always wait for a connection on RFCOMM open()".
Commit 4a2fb3ecc7,
"Bluetooth: Always wait for a connection on RFCOMM open()" open-codes
blocking on tty open(), rather than using the default behavior
implemented by the tty port.
The reasons for reverting that patch are detailed in that changelog;
this patch restores required functionality for that revert.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit 4a2fb3ecc7.
This is the second of a 3-patch revert, together with
Revert "Bluetooth: Remove rfcomm_carrier_raised()" and
Revert "Bluetooth: Move rfcomm_get_device() before rfcomm_dev_activate()".
Before commit cad348a17e,
Bluetooth: Implement .activate, .shutdown and .carrier_raised methods,
tty_port_block_til_ready() was open-coded in rfcomm_tty_install() as
part of the RFCOMM tty open().
Unfortunately, it did not implement non-blocking open nor CLOCAL open,
but rather always blocked for carrier. This is not the expected or
typical behavior for ttys, and prevents several common terminal
programming idioms from working (eg., opening in non-blocking
mode to initialize desired termios settings then re-opening for
connection).
Commit cad348a17e,
Bluetooth: Implement .activate, .shutdown and .carrier_raised methods,
added the necessary tty_port methods to use the default tty_port_open().
However, this triggered two important user-space regressions.
The first regression involves the complicated mechanism for reparenting
the rfcomm tty device to the ACL link device which represents an
open link to a specific bluetooth host. This regression causes ModemManager
to conclude the rfcomm tty device does not front a modem so it makes
no attempt to initialize an attached modem. This regression is
caused by the lack of a device_move() if the dlc is already open (and
not specifically related to the open-coded block_til_ready()).
A more appropriate solution is submitted in
"Bluetooth: Fix unsafe RFCOMM device parenting" and
"Bluetooth: Fix RFCOMM parent device for reused dlc"
The second regression involves "rfcomm bind" and wvdial (a ppp dialer).
rfcomm bind creates a device node for a /dev/rfcomm<n>. wvdial opens
that device in non-blocking mode (because it expects the connection
to have already been established). In addition, subsequent writes
to the rfcomm tty device fail (because the link is not yet connected;
rfcomm connection begins with the actual tty open()).
However, restoring the original behavior (in the patch which
this reverts) was undesirable.
Firstly, the original reporter notes that a trivial userspace
"workaround" already exists: rfcomm connect, which creates the
device node and establishes the expected connection.
Secondly, the failed writes occur because the rfcomm tty driver
does not buffer writes to an unconnected device; this contrasts with
the dozen of other tty drivers (in fact, all of them) that do just
that. The submitted patch "Bluetooth: Don't fail RFCOMM tty writes"
corrects this.
Thirdly, it was a long-standing bug to block on non-blocking open,
which is re-fixed by revert.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit f86772af6a.
This is the first of a 3-patch revert, together with
Revert "Bluetooth: Always wait for a connection on RFCOMM open()" and
Revert "Bluetooth: Move rfcomm_get_device() before rfcomm_dev_activate()".
Commit 4a2fb3ecc7,
"Bluetooth: Always wait for a connection on RFCOMM open()" open-codes
blocking on tty open(), rather than using the default behavior
implemented by the tty port.
The reasons for reverting that patch are detailed in that changelog;
this patch restores required functionality for that revert.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-By: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that the LE L2CAP Connection Oriented Channel support has undergone a
decent amount of testing we can make it officially supported. This patch
removes the enable_lecoc module parameter which was previously needed to
enable support for LE L2CAP CoC.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
checkpatch error: switch and case should be at the same indent.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix checkpatch errors below:
ERROR: "foo* bar" should be "foo *bar"
ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix checkpatch errors while the space is required or prohibited
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new fields to struct tcp_info, to report sk_pacing_rate
and sk_max_pacing_rate to monitoring applications, as ss from iproute2.
User exported fields are 64bit, even if kernel is currently using 32bit
fields.
lpaa5:~# ss -i
..
skmem:(r0,rb357120,t0,tb2097152,f1584,w1980880,o0,bl0) ts sack cubic
wscale:6,6 rto:400 rtt:0.875/0.75 mss:1448 cwnd:1 ssthresh:12 send
13.2Mbps pacing_rate 3336.2Mbps unacked:15 retrans:1/5448 lost:15
rcv_space:29200
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one inline keyword, and no need for a loop to find
an index into a table.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The solution was found by Patrick in 2.4 kernel sources.
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There are two checks for CONFIG_NET_CLS_ROUTE, but the corresponding
Kconfig symbol was dropped in v2.6.39. Since the code guards access to
dst_entry.tclassid it seems CONFIG_IP_ROUTE_CLASSID should be used
instead.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
