For newly added NVM parameters, older firmware may not have the support.
Suppress the error message to avoid the unncessary error message which is
triggered when devlink calls the driver during initialization.
Fixes: 782a624d00 ("bnxt_en: Add bnxt_en initial params table and register it.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If FW returns FRAG_ERR in response error code, driver is resending the
command only when HWRM command returns success. Fix the code to resend
NVM_INSTALL_UPDATE command with DEFRAG install flags, if FW returns
FRAG_ERR in its response error code.
Fixes: cb4d1d6261 ("bnxt_en: Retry failed NVM_INSTALL_UPDATE with defragmentation flag enabled.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both RX buffers and RX aggregation buffers have to be
replenished at the end of NAPI, post the RX aggregation buffers first
before RX buffers. Otherwise, we may run into a situation where
there are only RX buffers without RX aggregation buffers for a split
second. This will cause the hardware to abort the RX packet and
report buffer errors, which will cause unnecessary cleanup by the
driver.
Ringing the Aggregation ring doorbell first before the RX ring doorbell
will prevent some of these buffer errors. Use the same sequence during
ring initialization as well.
Fixes: 697197e5a1 ("bnxt_en: Re-structure doorbells.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device shutdown, the VNIC clearing sequence needs to be modified
to free the VNIC first before freeing the RSS contexts. The current
code is doing the reverse and we can get mis-directed RX completions
to CP ring ID 0 when the RSS contexts are freed and zeroed. The clearing
of RSS contexts is not required with the new sequence.
Refactor the VNIC clearing logic into a new function bnxt_clear_vnic()
and do the chip specific VNIC clearing sequence.
Fixes: 7b3af4f75b ("bnxt_en: Add RSS support for 57500 chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kalmia_init_and_get_ethernet_addr(), 'usb_buf' is allocated through
kmalloc(). In the following execution, if the 'status' returned by
kalmia_send_init_packet() is not 0, 'usb_buf' is not deallocated, leading
to memory leaks. To fix this issue, add the 'out' label to free 'usb_buf'.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cx82310_bind(), 'dev->partial_data' is allocated through kmalloc().
Then, the execution waits for the firmware to become ready. If the firmware
is not ready in time, the execution is terminated. However, the allocated
'dev->partial_data' is not deallocated on this path, leading to a memory
leak bug. To fix this issue, free 'dev->partial_data' before returning the
error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 04f05230c5 ("bnx2x: Remove configured vlans as
part of unload sequence."), introduced a regression in driver
that as a part of VF's reload flow, VLANs created on the VF
doesn't get re-configured in hardware as vlan metadata/info
was not getting cleared for the VFs which causes vlan PING to stop.
This patch clears the vlan metadata/info so that VLANs gets
re-configured back in the hardware in VF's reload flow and
PING/traffic continues for VLANs created over the VFs.
Fixes: 04f05230c5 ("bnx2x: Remove configured vlans as part of unload sequence.")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Sudarsana Kalluru <skalluru@marvell.com>
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In lan78xx_probe(), a new urb is allocated through usb_alloc_urb() and
saved to 'dev->urb_intr'. However, in the following execution, if an error
occurs, 'dev->urb_intr' is not deallocated, leading to memory leaks. To fix
this issue, invoke usb_free_urb() to free the allocated urb before
returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In myri10ge_probe(), myri10ge_alloc_slices() is invoked to allocate slices
related structures. Later on, myri10ge_request_irq() is used to get an irq.
However, if this process fails, the allocated slices related structures are
not deallocated, leading to memory leaks. To fix this issue, revise the
target label of the goto statement to 'abort_with_slices'.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
If oct->fn_list.enable_io_queues() fails, no cleanup is executed, leading
to memory/resource leaks. To fix this issue, invoke
octeon_delete_instr_queue() before returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited patch deleted ethtool flash device support, as ethtool core can
fallback into devlink flash callback. However, this is supported only if
there is a devlink port registered over the corresponding netdevice.
As mlx5e do not have devlink port support over native netdevice, it broke
the ability to flash device via ethtool.
This patch re-add the ethtool callback to avoid user functionality breakage
when trying to flash device via ethtool.
Fixes: 9c8bca2637 ("mlx5: Move firmware flash implementation to devlink")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a missing spinlock around XSKICOSQ usage at the activation stage,
because there is a race between a configuration change and the
application calling sendto().
Fixes: db05815b36 ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In blocked_fl_write(), 't' is not deallocated if bitmap_parse_user() fails,
leading to a memory leak bug. To fix this issue, free t before returning
the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
[0] https://marc.info/?t=156518400300003&r=1&w=2
Fixes: c1164bb1a6 ("net: phy: check PMAPMD link status only in genphy_c45_read_link")
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In mlx4_en_config_rss_steer(), 'rss_map->indir_qp' is allocated through
kzalloc(). After that, mlx4_qp_alloc() is invoked to configure RSS
indirection. However, if mlx4_qp_alloc() fails, the allocated
'rss_map->indir_qp' is not deallocated, leading to a memory leak bug.
To fix the above issue, add the 'qp_alloc_err' label to free
'rss_map->indir_qp'.
Fixes: 4931c6ef04 ("net/mlx4_en: Optimized single ring steering")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The ibm,mac-address-filters property defines the maximum number of
addresses the hypervisor's multicast filter list can support. It is
encoded as a big-endian integer in the OF device tree, but the virtual
ethernet driver does not convert it for use by little-endian systems.
As a result, the driver is not behaving as it should on affected systems
when a large number of multicast addresses are assigned to the device.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This driver does a funny dance disabling and re-enabling
RX and/or TX delays. In any of the RGMII-ID modes, it first
disables the delays, just to re-enable them again right
away. This looks like a needless exercise.
Just enable the respective delays when in any of the
relevant 'id' modes, and disable them otherwise.
Also, remove comments which don't add anything that can't be
seen by looking at the code.
Signed-off-by: André Draszik <git@andred.net>
CC: Andrew Lunn <andrew@lunn.ch>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
clang warns:
drivers/net/ethernet/toshiba/tc35815.c:1507:30: warning: use of logical
'&&' with constant operand [-Wconstant-logical-operand]
if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN)
^ ~~~~~~~~~~~~
drivers/net/ethernet/toshiba/tc35815.c:1507:30: note: use '&' for a
bitwise operation
if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN)
^~
&
drivers/net/ethernet/toshiba/tc35815.c:1507:30: note: remove constant to
silence this warning
if (!HAVE_DMA_RXALIGN(lp) && NET_IP_ALIGN)
~^~~~~~~~~~~~~~~
1 warning generated.
Explicitly check that NET_IP_ALIGN is not zero, which matches how this
is checked in other parts of the tree. Because NET_IP_ALIGN is a build
time constant, this check will be constant folded away during
optimization.
Fixes: 82a9928db5 ("tc35815: Enable StripCRC feature")
Link: https://github.com/ClangBuiltLinux/linux/issues/608
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To identify timestamps for matching with their packets, Spectrum-1 uses a
five-tuple of (port, direction, domain number, message type, sequence ID).
If there are several clients from the same domain behind a single port
sending Delay_Req's, the only thing differentiating these packets, as far
as Spectrum-1 is concerned, is the sequence ID. Should sequence IDs between
individual clients be similar, conflicts may arise. That is not a problem
to hardware, which will simply deliver timestamps on a first comes, first
served basis.
However the driver uses a simple hash table to store the unmatched pieces.
When a new conflicting piece arrives, it pushes out the previously stored
one, which if it is a packet, is delivered without timestamp. Later on as
the corresponding timestamps arrive, the first one is mismatched to the
second packet, and the second one is never matched and eventually is GCd.
To correct this issue, instead of using a simple rhashtable, use rhltable
to keep the unmatched entries.
Previously, a found unmatched entry would always be removed from the hash
table. That is not the case anymore--an incompatible entry is left in the
hash table. Therefore removal from the hash table cannot be used to confirm
the validity of the looked-up pointer, instead the lookup would simply need
to be redone. Therefore move it inside the critical section. This
simplifies a lot of the code.
Fixes: 8748642751 ("mlxsw: spectrum: PTP: Support SIOCGHWTSTAMP, SIOCSHWTSTAMP ioctls")
Reported-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the function names in two doc comments to match the corresponding
functions.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to the commit in the fixes tag, the resource controller in netdevsim
tracked fib entries and rules per network namespace. Restore that behavior.
Fixes: 5fc494225c ("netdevsim: create devlink instance per netdevsim instance")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a warning of "suspicious rcu_dereference_check() usage"
when nload runs.
Fixes: 776e726bfb ("netvsc: fix RCU warning in get_stats")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl1Mf5AACgkQSD+KveBX
+j7ztQgAiaCmQxJ6wV82KFVbmGA04oC3S0vz2lafTB1L3i2TqX6ZiRW07qGIPfml
HtylFu1Qta6sXDlJC5iQK48TnQaOr4HJqTxigofrWA3Pt7sYI1FNVG73BR1p8M5D
11ZZM6zCGkCd8cD5hTMzhvEr2d5NSMIy5wzC8DiiEph9JwAEh3ojeteP9KuwYdzX
/8W6swmwgMg/VKGlOwPhQcxSot0PcBm/a2sNjfGJ/NqyAb1yMQ5Bttt30A8346YN
kIhUBWIvDkbWDxxokRFGbpx5VswqJpMDKUEACWoJT44JyfFBMpMXPNe6wLvd1IIf
noxmAqe+CSTbr5UqJZdjqSrId5GhBA==
=X/dE
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-08-08' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-08-08
This series introduces some fixes to mlx5 driver.
Highlights:
1) From Tariq, Critical mlx5 kTLS fixes to better align with hw specs.
2) From Aya, Fixes to mlx5 tx devlink health reporter.
3) From Maxim, aRFs parsing to use flow dissector to avoid relying on
invalid skb fields.
Please pull and let me know if there is any problem.
For -stable v4.3
('net/mlx5e: Only support tx/rx pause setting for port owner')
For -stable v4.9
('net/mlx5e: Use flow keys dissector to parse packets for ARFS')
For -stable v5.1
('net/mlx5e: Fix false negative indication on tx reporter CQE recovery')
('net/mlx5e: Remove redundant check in CQE recovery flow of tx reporter')
('net/mlx5e: ethtool, Avoid setting speed to 56GBASE when autoneg off')
Note: when merged with net-next this minor conflict will pop up:
++<<<<<<< (net-next)
+ if (is_eswitch_flow) {
+ flow->esw_attr->match_level = match_level;
+ flow->esw_attr->tunnel_match_level = tunnel_match_level;
++=======
+ if (flow->flags & MLX5E_TC_FLOW_ESWITCH) {
+ flow->esw_attr->inner_match_level = inner_match_level;
+ flow->esw_attr->outer_match_level = outer_match_level;
++>>>>>>> (net)
To resolve, use hunks from net (2nd) and replace:
if (flow->flags & MLX5E_TC_FLOW_ESWITCH)
with
if (is_eswitch_flow)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_service_task() calls unregister_netdev() under rtnl_lock().
But unregister_netdev() internally calls rtnl_lock().
So deadlock would occur.
Fixes: 59dd45d550 ("ixgbe: firmware recovery mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As spin_unlock_irq will enable interrupts.
Function tsi108_stat_carry is called from interrupt handler tsi108_irq.
Interrupts are enabled in interrupt handler.
Use spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq
in IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should also enable team's vlan tx offload in hw_enc_features,
pass the vlan packets to the slave devices with vlan tci, let the
slave handle vlan tunneling offload implementation.
Fixes: 3268e5cb49 ("team: Advertise tunneling offload features")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/dsa/sja1105/sja1105_main.c: In function sja1105_fdb_dump:
drivers/net/dsa/sja1105/sja1105_main.c:1226:14: warning:
variable tx_vid set but not used [-Wunused-but-set-variable]
drivers/net/dsa/sja1105/sja1105_main.c:1226:6: warning:
variable rx_vid set but not used [-Wunused-but-set-variable]
They are not used since commit 6d7c7d948a ("net: dsa:
sja1105: Fix broken learning with vlan_filtering disabled")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As commit 30d8177e8a ("bonding: Always enable vlan tx offload")
said, we should always enable bonding's vlan tx offload, pass the
vlan packets to the slave devices with vlan tci, let them to handle
vlan implementation.
Now if encapsulation protocols like VXLAN is used, skb->encapsulation
may be set, then the packet is passed to vlan device which based on
bonding device. However in netif_skb_features(), the check of
hw_enc_features:
if (skb->encapsulation)
features &= dev->hw_enc_features;
clears NETIF_F_HW_VLAN_CTAG_TX/NETIF_F_HW_VLAN_STAG_TX. This results
in same issue in commit 30d8177e8a like this:
vlan_dev_hard_start_xmit
-->dev_queue_xmit
-->validate_xmit_skb
-->netif_skb_features //NETIF_F_HW_VLAN_CTAG_TX is cleared
-->validate_xmit_vlan
-->__vlan_hwaccel_push_inside //skb->tci is cleared
...
--> bond_start_xmit
--> bond_xmit_hash //BOND_XMIT_POLICY_ENCAP34
--> __skb_flow_dissect // nhoff point to IP header
--> case htons(ETH_P_8021Q)
// skb_vlan_tag_present is false, so
vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
//vlan point to ip header wrongly
Fixes: b2a103e6d0 ("bonding: convert to ndo_fix_features")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point nr_frags has been incremented but the frag does not yet
have a page assigned so freeing the skb results in a crash. Reset
nr_frags before freeing the skb to prevent this.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove check of recovery bit, in the beginning of the CQE recovery
function. This test is already performed right before the reporter
is invoked, when CQE error is detected.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
CQE recovery function begins with test and set of recovery bit. Add an
error flow which ensures clearing of this bit when leaving the recovery
function, to allow further recoveries to take place. This allows removal
of clearing recovery bit on sq activate.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove wrong error return value when SQ is not in error state.
CQE recovery on TX reporter queries the sq state. If the sq is not in
error state, the sq is either in ready or reset state. Ready state is
good state which doesn't require recovery and reset state is a temporal
state which ends in ready state. With this patch, CQE recovery in this
scenario is successful.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Shift the tisn field in the WQE control segment, per the
HW specification.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use the proper tisn field name from the union in struct mlx5_wqe_ctrl_seg.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The TLS progress params context WQE should not include an
Eth segment, drop it.
In addition, align the tls_progress_params layout with the
HW specification document:
- fix the tisn field name.
- remove the valid bit.
Fixes: a12ff35e0f ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Setting speed to 56GBASE is allowed only with auto-negotiation enabled.
This patch prevent setting speed to 56GBASE when auto-negotiation disabled.
Fixes: f62b8bb8f2 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: Mohamad Heib <mohamadh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Only support changing tx/rx pause frame setting if the net device
is the vport group manager.
Fixes: 3c2d18ef22 ("net/mlx5e: Support ethtool get/set_pauseparam")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We have an issue that OVS application creates an offloaded drop rule
that drops VXLAN traffic with both inner and outer header match
criteria. mlx5_core driver detects correctly the inner and outer
header match criteria but does not enable the inner header match criteria
due to an incorrect assumption in mlx5_eswitch_add_offloaded_rule that
only decap rule needs inner header criteria.
Solution:
Remove mlx5_esw_flow_attr's match_level and tunnel_match_level and add
two new members: inner_match_level and outer_match_level.
inner/outer_match_level is set to NONE if the inner/outer match criteria
is not specified in the tc rule creation request. The decap assumption is
removed and the code just needs to check for inner/outer_match_level to
enable the corresponding bit in firmware's match_criteria_enable value.
Fixes: 6363651d6d ("net/mlx5e: Properly set steering match levels for offloaded TC decap rules")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current ARFS code relies on certain fields to be set in the SKB
(e.g. transport_header) and extracts IP addresses and ports by custom
code that parses the packet. The necessary SKB fields, however, are not
always set at that point, which leads to an out-of-bounds access. Use
skb_flow_dissect_flow_keys() to get the necessary information reliably,
fix the out-of-bounds access and reuse the code.
Fixes: 18c908e477 ("net/mlx5e: Add accelerated RFS support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull networking fixes from David Miller:
"Yeah I should have sent a pull request last week, so there is a lot
more here than usual:
1) Fix memory leak in ebtables compat code, from Wenwen Wang.
2) Several kTLS bug fixes from Jakub Kicinski (circular close on
disconnect etc.)
3) Force slave speed check on link state recovery in bonding 802.3ad
mode, from Thomas Falcon.
4) Clear RX descriptor bits before assigning buffers to them in
stmmac, from Jose Abreu.
5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
loops, from Nishka Dasgupta.
6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.
7) Need to hold sock across skb->destructor invocation, from Cong
Wang.
8) IP header length needs to be validated in ipip tunnel xmit, from
Haishuang Yan.
9) Use after free in ip6 tunnel driver, also from Haishuang Yan.
10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
Heiner Kallweit.
11) Upon bridge device init failure, we need to delete the local fdb.
From Nikolay Aleksandrov.
12) Handle erros from of_get_mac_address() properly in stmmac, from
Martin Blumenstingl.
13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
Kadlecsik.
14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
some devices, so revert. From Johannes Berg.
15) Fix deadlock in rxrpc, from David Howells.
16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
Haibing.
17) Fix mvpp2 crash on module removal, from Matteo Croce.
18) Fix race in genphy_update_link, from Heiner Kallweit.
19) bpf_xdp_adjust_head() stopped working with generic XDP when we
fixes generic XDP to support stacked devices properly, fix from
Jesper Dangaard Brouer.
20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
David Ahern.
21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
net: dsa: sja1105: Fix memory leak on meta state machine error path
net: dsa: sja1105: Fix memory leak on meta state machine normal path
net: dsa: sja1105: Really fix panic on unregistering PTP clock
net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
net: sched: sample: allow accessing psample_group with rtnl
net: sched: police: allow accessing police->params with rtnl
net: hisilicon: Fix dma_map_single failed on arm64
net: hisilicon: fix hip04-xmit never return TX_BUSY
net: hisilicon: make hip04_tx_reclaim non-reentrant
tc-testing: updated vlan action tests with batch create/delete
net sched: update vlan action for batched events operations
net: stmmac: tc: Do not return a fragment entry
net: stmmac: Fix issues when number of Queues >= 4
net: stmmac: xgmac: Fix XGMAC selftests
be2net: disable bh with spin_lock in be_process_mcc
net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
...
The IS_ERR_OR_NULL(priv->clock) check inside
sja1105_ptp_clock_unregister() is preventing cancel_delayed_work_sync
from actually being run.
Additionally, sja1105_ptp_clock_unregister() does not actually get run,
when placed in sja1105_remove(). The DSA switch gets torn down, but the
sja1105 module does not get unregistered. So sja1105_ptp_clock_unregister
needs to be moved to sja1105_teardown, to be symmetrical with
sja1105_ptp_clock_register which is called from the DSA sja1105_setup.
It is strange to fix a "fixes" patch, but the probe failure can only be
seen when the attached PHY does not respond to MDIO (issue which I can't
pinpoint the reason to) and it goes away after I power-cycle the board.
This time the patch was validated on a failing board, and the kernel
panic from the fixed commit's message can no longer be seen.
Fixes: 29dd908d35 ("net: dsa: sja1105: Cancel PTP delayed work on unregister")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the FDB dump taken from first-generation switches also
contains information on whether entries are static or not. So use that
instead of searching through the driver's tables.
Fixes: d763778224 ("net: dsa: sja1105: Implement is_static for FDB entries on E/T")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When put under a bridge with vlan_filtering 0, the SJA1105 ports will
flood all traffic as if learning was broken. This is because learning
interferes with the rx_vid's configured by dsa_8021q as unique pvid's.
So learning technically still *does* work, it's just that the learnt
entries never get matched due to their unique VLAN ID.
The setting that saves the day is Shared VLAN Learning, which on this
switch family works exactly as desired: VLAN tagging still works
(untagged traffic gets the correct pvid) and FDB entries are still
populated with the correct contents including VID. Also, a frame cannot
violate the forwarding domain restrictions enforced by its classified
VLAN. It is just that the VID is ignored when looking up the FDB for
taking a forwarding decision (selecting the egress port).
This patch activates SVL, and the result is that frames with a learnt
DMAC are no longer flooded in the scenario described above.
Now exactly *because* SVL works as desired, we have to revisit some
earlier patches:
- It is no longer necessary to manipulate the VID of the 'bridge fdb
{add,del}' command when vlan_filtering is off. This is because now,
SVL is enabled for that case, so the actual VID does not matter*.
- It is still desirable to hide dsa_8021q VID's in the FDB dump
callback. But right now the dump callback should no longer hide
duplicates (one per each front panel port's pvid, plus one for the
VLAN that the CPU port is going to tag a TX frame with), because there
shouldn't be any (the switch will match a single FDB entry no matter
its VID anyway).
* Not really... It's no longer necessary to transform a 'bridge fdb add'
into 5 fdb add operations, but the user might still add a fdb entry with
any vid, and all of them would appear as duplicates in 'bridge fdb
show'. So force a 'bridge fdb add' to insert the VID of 0**, so that we
can prune the duplicates at insertion time.
** The VID of 0 is better than 1 because it is always guaranteed to be
in the ports' hardware filter. DSA also avoids putting the VID inside
the netlink response message towards the bridge driver when we return
this particular VID, which makes it suitable for FDB entries learnt
with vlan_filtering off.
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put() before
the return.
Additionally, the local variable ports in the function
qca8k_setup_mdio_bus() takes the return value of of_get_child_by_name(),
which gets a node but does not put it. If the function returns without
putting ports, it may cause a memory leak. Hence put ports before the
mid-loop return statement, and also outside the loop after its last usage
in this function.
Issues found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the arm64 platform, executing "ifconfig eth0 up" will fail,
returning "ifconfig: SIOCSIFFLAGS: Input/output error."
ndev->dev is not initialized, dma_map_single->get_dma_ops->
dummy_dma_ops->__dummy_map_page will return DMA_ERROR_CODE
directly, so when we use dma_map_single, the first parameter
is to use the device of platform_device.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_DESC_NUM is 256, in tx_count, the maximum value of
mod(TX_DESC_NUM - 1) is 254, the variable "count" in
the hip04_mac_start_xmit function is never equal to
(TX_DESC_NUM - 1), so hip04_mac_start_xmit never
return NETDEV_TX_BUSY.
tx_count is modified to mod(TX_DESC_NUM) so that
the maximum value of tx_count can reach
(TX_DESC_NUM - 1), then hip04_mac_start_xmit can reurn
NETDEV_TX_BUSY.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not try to return a fragment entry from TC list. Otherwise we may not
clean properly allocated entries.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When queues >= 4 we use different registers but we were not subtracting
the offset of 4. Fix this.
Found out by Coverity.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
