* device-properties:
serial: 8250_dw: Add quirk for APM X-Gene SoC
ACPI / LPSS: Provide build-in properties of the UART
ACPI / APD: Provide build-in properties of the UART
driver core: Don't leak secondary fwnode on device removal
The Altera 16550 soft IP UART requires 2 additional registers for
TX FIFO threshold support. These 2 registers enable the TX FIFO
Low Watermark and set the TX FIFO Low Watermark.
Set the TX FIFO threshold to the FIFO size - tx_loadsz.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize the tx_loadsz parameter from passed in devicetree
tx-threshold parameter.
The tx_loadsz is calculated as the number of bytes to fill FIFO
when tx-threshold is triggered.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Less magic that only requires comments.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have nice macro IRQ_RETVAL() we would use it to convert a flag of
handled interrupt from int to irqreturn_t.
The rationale of doing this is:
a) hence we implicitly mark hsu_dma_do_irq() as an auxiliary function that
can't be used as interrupt handler directly, and
b) to be in align with serial driver which is using serial8250_handle_irq()
that returns plain int by design.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
earlycon implementation used "unsigned long" internally, but there are systems
(ARM with LPAE) where sizeof(unsigned long) == 4 and uart is mapped beyond 4GiB
address range.
Switch to resource_size_t internally and replace obsoleted simple_strtoul() with
kstrtoull().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ACPI identifier for UART on Hisilicon Hip05 SoC, be careful that
it is not 16550 compatible, and "reg-io-width" and "reg-shift" need
be set properly by _DSD method in DSDT.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify the check of em485 variable to be either (em485) or (!em485) instead of
the explicit comparison to NULL.
While here, remove redundant check in __do_stop_tx_rs485() and
__stop_tx_rs485() since the functions ain't called with NULL value of em485
variable.
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are calls to serial8250_rpm_{get|put}() in __do_stop_tx_rs485() that are
certainly placed in a wrong location. I dunno how it had been tested with
runtime PM enabled because it is obvious "sleep in atomic context" error.
Besides that serial8250_rpm_get() is called immediately after an IO just
happened. It implies that the device is already powered on, see implementation
of serial8250_em485_rts_after_send() and serial8250_clear_fifos() for the
details.
There is no bug have been seen due to, as I can guess, use of auto suspend mode
when scheduled transaction to suspend is invoked quite lately than it's needed
for a few writes to the port. It might be possible to trigger a warning if
stop_tx_timer fires when device is suspended.
Refactor the code to use runtime PM only in case of timer function.
Fixes: 0c66940d58 ("tty/serial/8250: fix RS485 half-duplex RX")
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use an unified new dev variable instead of &pdev->dev and p->dev
in probe function.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The APM X-Gene SoC UART is the only board that still needs
the hard-coded values, so handle it separately in
dw8250_quirks(). The other ACPI platforms are able to
provide the values with device properties.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added devices ids for acces i/o products quad and octal serial cards
that make use of existing Pericom PI7C9X7954 and PI7C9X7958
configurations .
Signed-off-by: Jimi Damon <jdamon@accesio.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA on Intel Quark SoC is a part of UART IP block. Enable it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoCs, such as Intel Braswell, have DesignWare UART IP. Split out the
support of such chips to a separate module which also will be used for Intel
Quark later.
The rationale to have the separate driver to be existing:
- Do not contaminate 8250_pci.c anymore with LPSS related quirks
- All of them are using same DMA engine and they are Designware IP which means
that in the future we might share the code between 8250_dw.c and 8250_lpss.c
- It reduces the kernel memory footprint on non-X86 machines where 8250_pci.c
is in use
Besides the split the driver also has been refactored, in particular a) the DMA
and port setup are separate functions, b) the two new structures lpss8250 and
lpss8250_board are introduced to keep necessary data instead of
pciserial_board, c) DMA parameters are passed to the DMA setup via mentioned
custom structure. Most of the changes are done due to the future support of
UART DMA on Intel Quark.
The Intel Quark UART DMA support is based on bits taking from BSP code
published by Intel earlier.
The driver does not use any specific power management. PCI core takes care of
the default behaviour during suspend and resume.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Quark has 16550A compatible UART with autoflow feature enabled. It has
only 16 bytes of FIFO. Currently serial8250_do_set_termios() prevents to enable
autoflow since the minimum requirement of 32 bytes of FIFO size.
Drop a FIFO size limitation to allow autoflow control be enabled on such UARTs.
While here, comment out UART_CAP_AFE for PORT_AR7 since it wasn't working and
it will be not a good idea to use it in conjunction with trigger level of 1
byte.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UARTs, e.g. one is used in Intel Quark, have a different address base for
DMA operations. Introduce an additional field (per RX and TX DMA channels) in
struct uart_8250_dma to cover those cases.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mediatek can support baud rate up to 4M.
the 'uart_get_baud_rate' function will limit the max baud rate.
Modify max baud to remove the limit.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the commit c1a67b48f6 ("serial: 8250_pci: replace switch-case by
formula for Intel MID"), the 8250 driver crashes in the byt_set_termios()
function with a divide error. This is caused by the fact that a baud rate of 0
(B0) is not handled properly. Fix it by falling back to B9600 in this case.
Reported-by: "Mendez Salinas, Fernando" <fernando.mendez.salinas@intel.com>
Fixes: c1a67b48f6 ("serial: 8250_pci: replace switch-case by formula for Intel MID")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should check the data->pclk, not data->clk when get apb_pclk.
Fixes: c8ed99d4f6a8("serial: 8250_dw: Add support for deferred probing")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial console is broken in v4.8-rcX. Mika and I independently bisected down to
commit 4ef03d3287 ("tty/serial/8250: use mctrl_gpio helpers").
Since neither author nor anyone else didn't propose a solution we better revert
it for now.
This reverts commit 4ef03d3287.
Link: https://lkml.kernel.org/r/20160809130229.GN1729@lahna.fi.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bugfix for the fintek driver required defining some macros, but
one of them clashes with a system header on ARM:
drivers/tty/serial/8250/8250_fintek.c:34:0: error: "IRQ_MODE" redefined [-Werror]
#define IRQ_MODE 0x70
In file included from /git/arm-soc/arch/arm/include/asm/ptrace.h:13:0,
from /git/arm-soc/arch/arm/include/asm/irqflags.h:6,
from /git/arm-soc/include/linux/irqflags.h:15,
from /git/arm-soc/arch/arm/include/asm/bitops.h:27,
from /git/arm-soc/include/linux/bitops.h:36,
from /git/arm-soc/include/linux/kernel.h:10,
from /git/arm-soc/include/linux/list.h:8,
from /git/arm-soc/include/linux/module.h:9,
from /git/arm-soc/drivers/tty/serial/8250/8250_fintek.c:11:
arch/arm/include/uapi/asm/ptrace.h:55:0: note: this is the location of the previous definition
This renames the newly introduced 'IRQ_MODE' macro to FINTEK_IRQ_MODE.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4da22f1418 ("serial: 8250_fintek: fix the mismatched IRQ mode")
Link: https://patchwork.kernel.org/patch/9200119/
Acked-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #if defined(CONFIG_SERIAL_EARLYCON) && !defined(MODULE)
conditional has been added to the OF_EARLYCON_DECLARE() define.
The same conditional can be dropped from 8250_ingenic.c because
the unused symbols will be marked as __maybe_unsed.
Also, the Kconfig dependency can become much simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The !defined(MODULE) conditional has been added to the
OF_EARLYCON_DECLARE() define.
This commit partially reverts commit 3f5921a60f ("serial:
8250/mediatek: fix building with SERIAL_8250=m").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The !defined(MODULE) conditional has been added to the
OF_EARLYCON_DECLARE() define.
Now we can revert commit a2d3ea2f23 ("serial: 8250/uniphier:
fix modular build").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce serial8250_out_MCR() and serial8250_in_MCR() routines, that
replace following calls:
serial_out(port, UART_MCR, val)
serial_port_out(up, UART_MCR, val)
serial_in(port, UART_MCR)
This patch is needed in order to integrate reading/writing of MCR
signals via SERIAL_MCTRL_GPIO infrastructure later.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In DNV, when RX DMA is used and number of bytes received is less than
transfer size, only RX DMA timeout interrupt is sent. When this happens,
read the RX buffer.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export serial8250_rx_dma_flush() for use by SOC UART drivers.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow other code to safely read DMA Channel Status Register (where
the register attribute for Channel Error, Descriptor Time Out &
Descriptor Done fields are read-clear), export hsu_dma_get_status().
hsu_dma_irq() is renamed to hsu_dma_do_irq() and requires Status
Register value to be passed in.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the 8250 as a boot console and the main console results in
messages being printed twice. The console framework will only
unregister boot consoles if a new console is registered with the
CON_CONSDEV flag set.
Set this flag for the univ8250 console to prevent double-registration.
Signed-off-by: Matthew Leach <matthew.leach@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds support for the WCH CH355 4S card in the 8250 serial driver.
Signed-off-by: Alexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some BIOS only use _OSI("Linux") to distinguish between Linux & Windows.
Apply Level/Low to UART trigger mode if Windows, Edge/High mode otherwise.
But since 2.6.23 the mainline kernel no longer returns true for
_OSI(“Linux”).
The default IRQ0~15 trigger mode in Linux is Edge/High mode without
ACPI MADT override. It mismatches IRQ mode and makes UART malfunctional on
such motherboard.
This patch will check the current IRQ mode and apply correct mode to UART.
The following link is F81216AD spec PDF:
http://html.alldatasheet.com/html-pdf/257956/FINTEK/F81216AD/5569/
25/F81216AD.html
LDN0~3
70h: IRQ channel & Mode register
Bit 6~5 :
00 : Active low level mode
01 : Active high edge mode
Bit 4 : Sharing Flag (0: not share/1: share)
Bit 3~0 : IRQ channel
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some board like Hisilicon D02 uses Synopsys DesignWare ABP UART, declare an
OF early console for it, so early console device can be enabled with comand
line "earlycon"(without option) via the "stdout-path" property in device-tree.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The compiler complains about variables that are set, but never used:
* intX variables in exar_handle_irq
drivers/tty/serial/8250/8250_port.c:1864:34: warning: variable ‘int3’ set but not used [-Wunused-but-set-variable]
* val variable in pci_quatech_wqopr
drivers/tty/serial/8250/8250_pci.c:1139:10: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
And about a shadow variable:
* tmout in wait_for_xmitr is defined twice with the same type. Both of
them are also initialized before use.
Remove all of them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert DEBUG_INTR to pr_debug:
* defined semantics (DEBUG, DYNAMIC_DEBUG)
* KERN_DEBUG level instead of KERN_DEFAULT
* emit __func__ and \n
* verified 'fmt' even when !DEBUG
I wonder if anybody ever used that or whether we should just drop the
lines.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hub6 and irqflags from struct old_serial_port are nowhere set. Drop
them from the structure and replace the reads by zeros.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXPVb9AAoJEHwUBw8lI4NHnDQP/AtUYBTI8XD68iGh5eCTEtwO
3dNgUmOvIAIl0ZtVKex3b7j2S52IN7EDv44QmsmvMHgjvaupUsZ/HeIHgoI37y39
/qoRkyiG75ht68BrNjKcpJLsOyxaAUT1tMyf/bYXlDW8O7qEPtRDhuvUB+i+s3RX
ljNOQXH2WaQTJrNeZxkvbp92iGiu3j7AKyCh9MJ4gnF4y2oA1bFp++QpH5qcBOTp
0nccs7pgDQhw2nzHmhYbEmvgcKPrPQi+67U7eIed7n7wiThAIXIEbZl6AYk9kFaK
gSa4/N3fwnZc9TFR5O6qdanvsYdW4JC1P5Ydm0opExo3lgtMckQ3sGKFIwTG8eU4
YiyQE1uVHRqT82zxPCecTF+I0Y4g68oCJURrHED6kxKGA5a8ojU04aGebXDiNKlp
FEDceEC5ch7ZPw8CCTola+TYpf9Vni3g7OkrdkPY9cX/aDXDROghTCg9jgPJ2aL/
oai5axc5gQMEFzHPaEwFp45tgXw7IvIzaqYHmiWE11fsRbGUSB2HAwBXytI9ReC0
XTMBvc08YvisbIpIR29T0R5cerzdDuK9bXxYHHHOeUFg0t8R8UGaP1UxEQCVmLsT
AIrHupoccPJ7IAn0h6mShtZ2yzBfj3rU4tEMJR/Oj/VvjW3gKbbZ5XVi92fOurBs
xjn9uBBZ/Pt9hgprwlmY
=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
Commit cdcea058e5 ("serial: 8250_dw: Avoid serial_outx code duplicate
with new dw8250_check_lcr()") introduce a wrong logic when write val to
LCR reg. When CONFIG_64BIT enabled, __raw_writeq is used unconditionally.
The __raw_readq/__raw_writeq is introduced by commit bca2092d78 ("serial:
8250_dw: Use 64-bit access for OCTEON.") for OCTEON.
So for 64BIT && !PORT_OCTEON, we better to use coincident write function.
Fixes: cdcea058e510("serial: 8250_dw: Avoid serial_outx code duplicate with new dw8250_check_lcr()")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device HID AMDI0020 to match the AMD ACPI Vendor ID (AMDI) as
registered in http://www.uefi.org/acpi_id_list, and the UART
controller on future AMD paltform will use the HID instead of AMD0020.
Signed-off-by: Wang Hongcheng <annie.wang@amd.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_fintek driver advertises as the PNP0501 driver; however this
conflicts with the standard 16550A uart PNP0501. The conflict causes
the 8250_fintek driver to load with _every_ PNP0501, but never probe,
and causing the entire 8250 driver stack to unload if the 8250_fintek
driver is unloaded (modprobe doesn't know that 8250_pnp rather than
8250_fintek claimed the resource).
This patch merges the Fintek driver into 8250_base. On autoconfig_16550
the device is probed to verify if it is a FINTEK device or not.
This custom probing can be disabled completely via configuration. When a
Fintek device is not probed it will behave as a standard 16550A device,
with no RS485 capabilities.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is not used outside the file, so it can be static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA completed normally does not require termination; only terminate
paused rx dma stemming from rx dma flush.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using fake IIR values to perform rx dma operations unnecessarily
conflates separate operations, stopping in-progress dma with starting
new dma.
Introduce serial8250_rx_dma_flush() to handle stopping in-progress dma
[omap8250 already has equivalent omap_8250_rx_dma_flush()].
Replace rx_dma(UART_IIR_RX_TIMEOUT) with the equivalent *_rx_dma_flush(),
and rx_dma(0) with the equivalent *_rx_dma(). Handle IIR steering
in the irq handler with handle_rx_dma() helper.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the operation (restarting new rx dma) performed when error
argument is true.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27c310c5c3 ("serial: 8250_dma: no need to sync RX buffer")
notes the RX DMA buffer is allocated from DMA coherent memory, and
thus does not need sync'd for each transaction. The same is true
for OMAP RX DMA.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 dma support requires the dmaegine driver support terminate.
Query slave caps to determine if necessary commands/properties are
supported; disable dma if not.
Note this means dmaengine driver must support slave caps reporting
as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 dma support requires the dmaengine driver support error-free
pause/terminate and better-than-descriptor residue granularity. Query
slave caps to determine if necessary commands/properties are supported;
disable dma if not.
Note this means dmaengine driver must support slave caps reporting
as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HIGH_BITS_OFFSET is only used in the serial core; remove from 8250-
specific header.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If !up->dma == F, then up->dma == T and can be elided from the
(up->dma && up->dma->tx_err) sub-expression.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_err is not used other than for boolean evaluation;
substitute the actual operation directly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Intel Penwell and Tangier the HSU block (3 HSU ports) has a global register
set which is currently not used by the driver. On Tangier it has it's own PCI
device and thus available for enumeration. Since it's not a real HSU port we
just skip it and therefore put a comment in the code why we do so.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to compile module on non-X86 platforms, though COMPILE_TEST
is provided for sake of what it does.
While here, set default to SERIAL_8250 that user doesn't need an explicit
option to be set and hide it from non-expert.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BIT() macro, that is definded in bitops.h, is used in the driver. Include
necessary header for that.
While here, reorder included headers alphabetically.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a special register that shows interrupt status by source. In
particular case the source can be a combination of DMA Tx, DMA Rx, and UART.
Read the register and call the handlers only for sources that request an
interrupt.
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.
Reported-by: "Lai, Poey Seng" <poey.seng.lai@intel.com>
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bay Trail UART port does not support DCD and DSR lines. The driver
shall report that these signals are permanently active. This patch
is for HSUART enumerated via PCI.
For ACPI, see commit dfd37668ea ("serial: 8250_dw: Fix get_mctrl
behaviour"). The commit also describes the possible issue if these
signals are enabled on a port without these pins.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exposes get_mctrl() function so that it can be overriden with platform
specific implementation.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 21947ba654 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Fixes: 21947ba654 ("serial: 8250_pci: replace switch-case by formula")
Cc: stable@vger.kernel.org
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8d2acdb9fc.
It's causing problems, and somehow I missed that Peter didn't like it at
all :(
So revert it for now until it gets sorted out.
Reported-by: Mason <slash.tmp@free.fr>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
When in half-duplex mode RX will be disabled before TX, but not
enabled after deactivating transmitter. This patch enables
UART_IER_RLSI and UART_IER_RDI interrupts after TX is over.
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Acked-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
CONFIG_SERIAL_8250_RSA has waited for a long
time to have meaningful help text so let's
finally describe what this option actually does.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
up_to_u8250p() casts struct uart_port * to struct uart_8250_port *. Update code
to use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Mediatek 8250 driver has a 'bool' Kconfig symbol, but that
breaks when SERIAL_8250 is a loadable module:
drivers/tty/built-in.o: In function `mtk8250_set_termios':
:(.text+0x1bee8): undefined reference to `serial8250_do_set_termios'
:(.text+0x1bf10): undefined reference to `uart_get_baud_rate'
:(.text+0x1c09c): undefined reference to `uart_get_divisor'
drivers/tty/built-in.o: In function `mtk8250_do_pm':
:(.text+0x1c0d0): undefined reference to `serial8250_do_pm'
drivers/tty/built-in.o: In function `mtk8250_probe':
:(.text+0x1c2e4): undefined reference to `serial8250_register_8250_port'
serial/8250/8250_mtk.c:287:242: error: data definition has no type or storage class [-Werror]
serial/8250/8250_mtk.c:287:122: error: 'mtk8250_platform_driver_init' defined but not used [-Werror=unused-function]
This changes the symbol to a 'tristate', so the dependency on
SERIAL_8250 also works when that is set to 'm'.
To actually build the driver, we also need to include <linux/module.h>.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Ingenic 8250 driver has a 'bool' Kconfig symbol, but that
breaks when SERIAL_8250 is a loadable module:
drivers/tty/built-in.o: In function `ingenic_uart_probe':
8250_ingenic.c:(.text+0x1c1a0): undefined reference to `serial8250_register_8250_port'
This changes the symbol to a 'tristate', plus a dependency on
SERIAL_8250, which makes it work again. Unlike the other
soc-specific backends, this one has no dependency on an
architecture or a platform. I'm adding a dependency on
MIPS || COMPILE_TEST as well here, to avoid showing the driver
on architectures that are not interested in it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added uniphier serial port driver fails to build as
a loadable module when the base 8250 driver is built-in and
its console support enabled:
ERROR: "early_serial8250_setup" [drivers/tty/serial/8250/8250_uniphier.ko] undefined!
This changes the driver to only provide the early console support
if it is built-in itself as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cafe1ac640 ("drivers/tty: make serial
8250_ingenic.c explicitly non-modular"), which attempted to remove dead
code but did not have the desired effect when the main 8250 driver was
a loadable module itself.
This would normally result in a link error, but as the entire
drivers/tty/serial/8250/ directory is only entered when CONFIG_SERIAL_8250
is set, we never notice that the driver does not get built in this
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d72d391c12 ("drivers/tty/serial: make
8250/8250_mtk.c explicitly non-modular"), which intended to remove dead
code but did not have the desired effect when the main 8250 driver was
a module itself.
This would normally result in a link error, but as the entire
drivers/tty/serial/8250/ directory is only entered when CONFIG_SERIAL_8250
is set, we never notice that the driver does not get built in this
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kconfig option SERIAL_8250_RT288X seems to be only relevant on MIPS
platforms, so do not present it on other architectures, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to have channel offset defined since all BayTrail and Braswell
ports are 1 channel. Remove unneeded definition.
While here, remove comment which has no value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The managed API provides a better approach to help with acquiring and releasing
resources. Besides that error handling becomes simpler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clocks are managed through clk-fractional-divider.c module, and thus CLK
framework takes care about it. Remove letfovers from this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the main branch contains return statement the 'else' keyword is not
needed. Remove it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_em485_init() is supposed to be protected with
p->port.lock spinlock.
This may lead to issues when kmalloc sleeps, so it is better to use
GFP_ATOMIC in this spinlocked context.
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Reported-by: Ильяс Гасанов <torso.nafi@gmail.com>
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Formally, currently there is no memory leak, but if
serial8250_ports[line] is reused with other 8250 driver, then em485
will be already activated and it will cause issues.
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes error condition check when requesting the irq,
that would not trigger because of uart_port.irq being
defined as unsigned int.
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare an OF early console for Tegra so that the early console device
can be specified via the "stdout-path" property in device-tree.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mtk8250_runtime_suspend function is not used when runtime PM is
disabled, so we get a warning about an unused function:
drivers/tty/serial/8250/8250_mtk.c:119:12: error: 'mtk8250_runtime_suspend' defined but not used [-Werror=unused-function]
static int mtk8250_runtime_suspend(struct device *dev)
This marks all the PM functions as __maybe_unused to avoid the warning,
and removes the #ifdef around the PM_SLEEP functions for consistency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d56edd7ed0, it
shouldn't have been applied, it was fixed properly with commit
71f50c6d9a ("of: drop symbols declared by
_OF_DECLARE() from modules")
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes redundant 8250 port initialization macros and
replaces them by a single generic base-macro, which is specialized
as needed.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checkpatch complains about incorrect indentation of switch/case statements.
This patch fixes the corresponding warnings. Additionally some indentation
is changed to match the correct format specified in the Linux Kernel
Coding Style.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch refactors a switch case statement by merging an if condition
in the default case into an identical condition right after the switch
statement.
This comes with a slight change in behaviour: If pci_netmos_9900_numports
returns 0, an additional warning is printed.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes compiler warnings about wrong conversion specifiers used
in a debug output in 8250_pnp.c. The precise warning is:
drivers/tty/serial/8250/8250_pnp.c: In function ‘serial_pnp_probe’:
include/linux/dynamic_debug.h:64:16: warning: format ‘%x’ expects argument
of [...]
drivers/tty/serial/8250/8250_pnp.c:467:2: note: in expansion of macro
‘dev_dbg’
dev_dbg(&dev->dev,
^
include/linux/dynamic_debug.h:64:16: warning: format ‘%lx’ expects argument
of [...]
drivers/tty/serial/8250/8250_pnp.c:467:2: note: in expansion of macro
‘dev_dbg’
dev_dbg(&dev->dev,
^
Those warnings never got triggered, because the command was nested
in an #ifdef, which is removed by a patch of this series.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the macro SERIAL_DEBUG_PNP, which is used to enable
debugging at compile time.
As SERIAL_DEBUG_PNP is an orphan, the corresponding #ifdef is removed.
To keep the ability to enable debugging at compile time,
the call to printk(KERN_DEBUG ...) is replaced by a corresponding
call to dev_dbg(), which is configurable via CONFIG_DYNAMIC_DEBUG.
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces printk by the corresponding variant of dev_* in order
to fix checkpatch warnings. If no suitable device pointer is present, the
corresponding pr_* variant is used.
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merged user-visible multi-line strings into a single line according to the
Linux Kernel Coding Style, which allows user-visible strings to exceed the
maximum line length of 80 characters. The main reason for this is to
facilitate grepping for these strings.
However, some strings were ignored in this patch, because the use of
format specifiers breaks the ability to grep anyway.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a checkpatch warning caused by missing parentheses
in the definition of a macro.
Furthermore redundant parentheses are removed in an assignment.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed checkpatch warning about an unnecessary line continuation in a
multi-line variable assignment.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves EXPORT_SYMBOL macros directly after the definition of
the corresponding symbol to remove checkpatch warnings.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
