Current dwmac4_flow_ctrl will not clear
GMAC_RX_FLOW_CTRL_RFE/GMAC_RX_FLOW_CTRL_RFE bits,
so MAC hw will keep flow control on although expecting
flow control off by ethtool. Add codes to fix it.
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the default value of tx-frames is 25, it's too late when
passing tstamp to stack, then the ptp4l will fail:
ptp4l -i eth0 -f gPTP.cfg -m
ptp4l: selected /dev/ptp0 as PTP clock
ptp4l: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 1: link up
ptp4l: timed out while polling for tx timestamp
ptp4l: increasing tx_timestamp_timeout may correct this issue,
but it is likely caused by a driver bug
ptp4l: port 1: send peer delay response failed
ptp4l: port 1: LISTENING to FAULTY on FAULT_DETECTED (FT_UNSPECIFIED)
ptp4l tests pass when changing the tx-frames from 25 to 1 with
ethtool -C option.
It should be fine to set tx-frames default value to 1, so ptp4l will pass
by default.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
disable rx watchdog for dwmac-mediatek, then the hw will
issue a rx interrupt once receiving a packet, so the responding time
for rx path will be reduced.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add Ethernet power on/off operations in init/exit flow.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix OOPS during nf_tables rule dump, from Florian Westphal.
2) Use after free in ip_vs_in, from Yue Haibing.
3) Fix various kTLS bugs (NULL deref during device removal resync,
netdev notification ignoring, etc.) From Jakub Kicinski.
4) Fix ipv6 redirects with VRF, from David Ahern.
5) Memory leak fix in igmpv3_del_delrec(), from Eric Dumazet.
6) Missing memory allocation failure check in ip6_ra_control(), from
Gen Zhang. And likewise fix ip_ra_control().
7) TX clean budget logic error in aquantia, from Igor Russkikh.
8) SKB leak in llc_build_and_send_ui_pkt(), from Eric Dumazet.
9) Double frees in mlx5, from Parav Pandit.
10) Fix lost MAC address in r8169 during PCI D3, from Heiner Kallweit.
11) Fix botched register access in mvpp2, from Antoine Tenart.
12) Use after free in napi_gro_frags(), from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (89 commits)
net: correct zerocopy refcnt with udp MSG_MORE
ethtool: Check for vlan etype or vlan tci when parsing flow_rule
net: don't clear sock->sk early to avoid trouble in strparser
net-gro: fix use-after-free read in napi_gro_frags()
net: dsa: tag_8021q: Create a stable binary format
net: dsa: tag_8021q: Change order of rx_vid setup
net: mvpp2: fix bad MVPP2_TXQ_SCHED_TOKEN_CNTR_REG queue value
ipv4: tcp_input: fix stack out of bounds when parsing TCP options.
mlxsw: spectrum: Prevent force of 56G
mlxsw: spectrum_acl: Avoid warning after identical rules insertion
net: dsa: mv88e6xxx: fix handling of upper half of STATS_TYPE_PORT
r8169: fix MAC address being lost in PCI D3
net: core: support XDP generic on stacked devices.
netvsc: unshare skb in VF rx handler
udp: Avoid post-GRO UDP checksum recalculation
net: phy: dp83867: Set up RGMII TX delay
net: phy: dp83867: do not call config_init twice
net: phy: dp83867: increase SGMII autoneg timer duration
net: phy: dp83867: fix speed 10 in sgmii mode
net: phy: marvell10g: report if the PHY fails to boot firmware
...
kfree_skb() shall be used instead of kfree(). Fix it.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable shall be __be16. Fix it.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of devm_alloc_etherdev_mqs() to simplify the code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix gcc build error while CONFIG_INET is not set
drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.o: In function `__stmmac_test_loopback':
stmmac_selftests.c:(.text+0x8ec): undefined reference to `ip_send_check'
stmmac_selftests.c:(.text+0xacc): undefined reference to `udp4_hwcsum'
Add CONFIG_INET dependency to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the netdev is registered, calling netdev_info() will emit
something as "(unnamed net device) (uninitialized)", looks confusing.
Before this patch:
[ 3.155028] stmmaceth f7b60000.ethernet (unnamed net_device) (uninitialized): device MAC address 52:1a:55:18:9e:9d
After this patch:
[ 3.155028] stmmaceth f7b60000.ethernet: device MAC address 52:1a:55:18:9e:9d
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the subdriver defers probe, do not show an error message. It's
perfectly fine for this error to occur since the driver will get another
chance to probe after some time and will usually succeed after all of
the resources that it requires have been registered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. the frequency of csr clock is 66.5MHz, so the csr_clk value should
be 0 other than 5.
2. the csr_clk can be got from device tree, so remove initialization here.
Fixes: 9992f37e34 ("stmmac: dwmac-mediatek: add support for mt2712")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The specific clk_csr value can be zero, and
stmmac_clk is necessary for MDC clock which can be set dynamically.
So, change the condition from plat->clk_csr to plat->stmmac_clk to
fix clk_csr can't be zero issue.
Fixes: cd7201f477 ("stmmac: MDC clock dynamically based on the csr clock input")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we will not update the receive descriptor tail pointer in
stmmac_rx_refill. Rx dma will think no available descriptors and stop
once received packets exceed DMA_RX_SIZE, so that the rx only test will fail.
Update the receive tail pointer in stmmac_rx_refill to add more descriptors
to the rx channel, so packets can be received continually
Fixes: 54139cf3bb ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later". Only the "obvious" versions of these matches are
included here, a number of "non-obvious" variants of text have been
found but those have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOgmlw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk4rACfRqxGOGVLR/t6E9dDzOZRAdEz/mYAoJLZmziY
0YlSSSPtP5HI6JDh65Ng
=HXQb
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pule more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later".
Only the "obvious" versions of these matches are included here, a
number of "non-obvious" variants of text have been found but those
have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (85 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 125
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 123
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 122
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 121
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 120
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 119
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 118
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 116
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 114
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 113
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 112
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 111
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 110
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 106
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 105
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 104
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 103
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 102
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 101
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 98
...
When we trigger NAPI we are disabling interrupts but in case we receive
or send a packet in the meantime, as interrupts are disabled, we will
miss this event.
Trigger both NAPI instances (RX and TX) when at least one event happens
so that we don't miss any interrupts.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.
Found out while running stmmac selftests.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to disable the whole RX when dma_stop_rx() is called
because there may be the need of just disabling 1 DMA channel.
This is also needed for stmmac Flow Control selftest.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to disable the whole RX when dma_stop_rx() is called
because there may be the need of just disabling 1 DMA channel.
This is also needed for stmmac Flow Control selftest.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for hash filter to work we need to set the HPF bit.
Fout out while running stmmac selftests
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.
Found out while running stmmac selftests.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for hash filter to work we need to set the HPF bit.
Found out while running stmmac selftests.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add support for selftests on stmmac driver with 9 basic sanity checks
for now:
- MAC Loopback
- PHY Loopback
- MMC Counters
- EEE
- Hash Filter Multicast
- Perfect Filter Unicast
- Multicast Filter All
- Unicast Filter All
- Flow Control
This allows for fast tracking of regressions in the driver and helps in
spotting mis-configuration of HW.
Changes from v1:
- Fix build error as module (David)
- Check for link status before running tests
Changes from RFC v2:
- Return proper error code in stmmac_test_mmc (Corentin)
- Use only 1 MMC counter in stmmac_test_mmc (Alexandre)
Changes from RFC v1:
- Change test_loopback to test_mac_loopback (Andrew)
- Change timeout to retries (Andrew)
- Add MC/UC filter tests (Andrew)
- Only test in offline mode (Andrew)
- Do not call phy_loopback twice (Alexandre)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the selftests to run the Flow Control selftest we need to
also pass pause frames to the stack.
Pass this type of frames while in promiscuous mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the selftests to run the Flow Control selftest we need to
also pass pause frames to the stack.
Pass this type of frames while in promiscuous mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the selftests to run the Flow Control selftest we need to
also pass pause frames to the stack.
Pass this type of frames while in promiscuous mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC has a different MMC module. Lets use HWIF callbacks for MMC module
so that correct callbacks are automatically selected.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enable use of set_mac_loopback in dwmac-sun8i
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwxgmac2 core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwmac4/5 cores.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwmac1000 core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwmac100 core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the addition of selftests support for stmmac we add a
new callback to HWIF that can be used to set the controller in loopback
mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
licensed under the gplv2 or at your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091651.323272658@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 984203ceff ("net: stmmac: mdio: remove reset gpio free")
removed the reset gpio free, when the driver is unbinded or rmmod,
we miss the gpio free.
This patch uses managed API to request the reset gpio, so that the
gpio could be freed properly.
Fixes: 984203ceff ("net: stmmac: mdio: remove reset gpio free")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stmmac_init_chan() needs to be called before stmmac_init_rx_chan() and
stmmac_init_tx_chan(). This is because if PBLx8 is to be used,
"DMA_CH(#i)_Control.PBLx8" needs to be set before programming
"DMA_CH(#i)_TX_Control.TxPBL" and "DMA_CH(#i)_RX_Control.RxPBL".
Fixes: 47f2a9ce52 ("net: stmmac: dma channel init prepared for multiple queues")
Reviewed-by: Zhang, Baoli <baoli.zhang@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ethtool was not able to get/set the flow control due to a
missing "!". It will always return -EOPNOTSUPP even the device is
flow control supported.
This patch fixes the condition check for ethtool flow control get/set
function for ETHTOOL_LINK_MODE_Asym_Pause_BIT.
Fixes: 3c1bcc8614 (“net: ethernet: Convert phydev advertize and supported from u32 to link mode”)
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon, Weifeng <weifeng.voon@intel.com@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Document (kerneldoc) core mfd_add_devices() API
- New Drivers
- Add support for Altera SOCFPGA System Manager
- Add support for Maxim MAX77650/77651 PMIC
- Add support for Maxim MAX77663 PMIC
- Add support for ST Multi-Function eXpander (STMFX)
- New Device Support
- Add support for LEDs to Intel Cherry Trail Whiskey Cove PMIC
- Add support for RTC to SAMSUNG Electronics S2MPA01 PMIC
- Add support for SAM9X60 to Atmel HLCDC (High-end LCD Controller)
- Add support for USB X-Powers AXP 8xx PMICs
- Add support for Integrated Sensor Hub (ISH) to ChromeOS EC
- Add support for USB PD Logger to ChromeOS EC
- Add support for AXP223 to X-Powers AXP series PMICs
- Add support for Power Supply to X-Powers AXP 803 PMICs
- Add support for Comet Lake to Intel Low Power Subsystem
- Add support for Fingerprint MCU to ChromeOS EC
- Add support for Touchpad MCU to ChromeOS EC
- Move TI LM3532 support to LED
- New Functionality
- Add/extend DT support; max77650, max77620
- Add support for power-off; max77620
- Add support for clocking; syscon
- Add support for host sleep event; cros_ec
- Fix-ups
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
- Bug Fixes
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio
-----BEGIN PGP SIGNATURE-----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=dTSD
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Document (kerneldoc) core mfd_add_devices() API
New Drivers:
- Altera SOCFPGA System Manager
- Maxim MAX77650/77651 PMIC
- Maxim MAX77663 PMIC
- ST Multi-Function eXpander (STMFX)
New Device Support:
- LEDs support in Intel Cherry Trail Whiskey Cove PMIC
- RTC support in SAMSUNG Electronics S2MPA01 PMIC
- SAM9X60 support in Atmel HLCDC (High-end LCD Controller)
- USB X-Powers AXP 8xx PMICs
- Integrated Sensor Hub (ISH) in ChromeOS EC
- USB PD Logger in ChromeOS EC
- AXP223 in X-Powers AXP series PMICs
- Power Supply in X-Powers AXP 803 PMICs
- Comet Lake in Intel Low Power Subsystem
- Fingerprint MCU in ChromeOS EC
- Touchpad MCU in ChromeOS EC
- Move TI LM3532 support to LED
New Functionality:
- max77650, max77620: Add/extend DT support
- max77620 power-off
- syscon clocking
- croc_ec host sleep event
Fix-ups:
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
Bug Fixes:
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio"
* tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: Use dev_get_drvdata() directly
mfd: cros_ec: Instantiate properly CrOS Touchpad MCU device
mfd: cros_ec: Instantiate properly CrOS FP MCU device
mfd: cros_ec: Update the EC feature codes
mfd: intel-lpss: Add Intel Comet Lake PCI IDs
mfd: lochnagar: Add links to binding docs for sound and hwmon
mfd: ab8500-debugfs: Fix a typo ("deubgfs")
mfd: imx6sx: Add MQS register definition for iomuxc gpr
dt-bindings: mfd: LMU: Fix lm3632 dt binding example
mfd: intel_quark_i2c_gpio: Adjust IOT2000 matching
mfd: da9063: Fix OTP control register names to match datasheets for DA9063/63L
mfd: tps65912-spi: Add missing of table registration
mfd: axp20x: Add USB power supply mfd cell to AXP803
mfd: sun6i-prcm: Fix build warning for non-OF configurations
mfd: intel-lpss: Set the device in reset state when init
platform/chrome: Add support for v1 of host sleep event
mfd: cros_ec: Add host_sleep_event_v1 command
mfd: cros_ec: Instantiate the CrOS USB PD logger driver
mfd: cs47l90: Make DAC_AEC_CONTROL_2 readable
mfd: cs47l35: Make DAC_AEC_CONTROL_2 readable
...
-----BEGIN PGP SIGNATURE-----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=55X1
-----END PGP SIGNATURE-----
Merge branches 'ib-mfd-arm-leds-5.2', 'ib-mfd-gpio-input-leds-power-5.2', 'ib-mfd-pinctrl-5.2-2' and 'ib-mfd-regulator-5.2', tag 'ib-mfd-arm-net-5.2' into ibs-for-mfd-merged
Immutable branch between MFD, ARM and Net due for the 5.2 merge window
When adding more MAC addresses to a dwmac-sun8i interface, the device goes
directly in promiscuous mode.
This is due to IFF_UNICAST_FLT missing flag.
So since the hardware support unicast filtering, let's add IFF_UNICAST_FLT.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: stmmac: dwmac4_prog_mtl_tx_algorithms() missing write operation
The value of MTL_OPERATION_MODE is not written back
Signed-off-by: Cheng Han <hancheng2009@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
