Our SGMII phy code was incomplete in that it was not actually placing the
phy in SGMII mode and as a result the PHY was not able to establish a link
when connected to a non serdes link partner. This patch updates the code
to combine the SGMII/serdes PCS init and to add the necessary reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates things so that vlan tags are taken into account when
setting the receive large packet maximum length. This allows the VF driver
to correctly receive full sized frames when vlans are enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb_irq_disable/enable calls were causing virtual functions associated
with the igb physical function to have their interrupts disabled. In order
to prevent this from occuring we should only clear/set the bits related to
the physical function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the set_rx_mode netdevice operation so that igb
can better support multiple unicast addresses.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were already exporting TSO6 to the vlan, but we weren't exporting the
checksum support for IPV6 which was causing warning messages to be
displayed when doing IPv6 TSO over a vlan.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the flow control configuration for igb to make it a
bit more readable in regards to what the requested and current modes are.
This should help with the maintainability of the current igb driver in
regards to flow control.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that we use buffer_info->dma instead of
shinfo->nr_frags to determine if we need to unmap a received skb. By doing
this we can avoid a cache miss on small packets since the buffer_info
structure should already be prefetched.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a new 82576 mezzanine adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves all of the multicast addresses out of the free Receive
address registers and instead programs them all into the multicast table
array. As a result the multicast filtering may not be as precise, but it
also greatly reduces the overhead for multicast addresses.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82575 and 82576 hardware can both experience data corruption issues if
a pci-e completion arrives after the timeout value. In order to avoid this
we need to increase the timeout value while pci-e master is disabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current igb driver only supports copper and serdes. The fiber media
type is a holdover from earlier NICs as the current nics supported by igb
all use serdes when communicating over a fiber connection. As a result we
can remove media type fiber without losing any functionality.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
forward declaration of inline function should be avoided, or
old gcc cannot compile.
Reported-by: Teck Choon Giam <giamteckchoon@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI drivers that implement the io_error_detected callback should return
PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure. This patch fixes the issue for igb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
driver was mixing NET_IP_ALIGN count bytes in map/unmap calls
unevenly. Only map the bytes that the hardware might dma into
also fix unmap related bug where ->dma was not being cleared
after unmap
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.
One to access nr_frags, one to access dma_maps[0]
Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.
Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on previous patch from Jesper Dangaard Brouer.
The RNBC (Receive No Buffers Count) register for the 82576, indicate
that frames were received when there were no available buffers in host
memory to store those frames (receive descriptor head and tail
pointers were equal). The packet is still received by the NIC if
there is space in the FIFO on the NIC.
As the RNBC value is not a packet drop, the driver stores this value
in net_stats.rx_fifo_errors to indicate that there were no system
buffers available for the incoming packet. Actual dropped packets
are counted in the MPC value.
Saving the stats in dev->net_stats makes it visible via
/proc/net/dev as "fifo", and thus viewable to ifconfig
as "overruns" and 'netstat -i' as "RX-OVR".
The Receive No Buffers Count (RNBC) can already be queried by
ethtool -S as "rx_no_buffer_count".
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the previous patches from Jesper Dangaard Brouer <hawk@comx.dk>
Implement reading the per queue drop stats register
RQDPC (Receive Queue Drop Packet Count). It counts the number of
packets dropped by a queue due to lack of descriptors available.
Notice RQDPC (Receive Queue Drop Packet Count) stats only gets
incremented, if the DROP_EN bit it set (in the SRRCTL register
for that queue). If DROP_EN bit is NOT set, then the some what
equivalent count is stored in RNBC (not per queue basis).
The RQDPC register is only 12 bit, thus the precision might
suffer due to overrun in-netween the watchdog polling interval.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver is re-registering the DCA requester after every reset.
Instead of doing this we should only be updating the on board DCA registers
and not unregistering/re-registering our requester.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after the recent changes to wired drivers to use only
netif_carrier_off the driver can have outstanding tx work to
complete that will never complete once link is down. Since the
intel hardware will hold this tx work forever, the driver
notices a tx timeout condition internally and might try
to instigate printk and reset of the part with a
netif_stop_queue, which doesn't work because link is down.
Don't bother arming to tx hang detection when link is down.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup_rctl call was making a call into the ring structure after it had
been freed. This was causing a panic on shutdown. This call wasn't
necessary since it is possible to get the needed index from
adapter->vfs_allocated_count.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An issue was found in which rx checksum could not be enabled without
resetting the interface. The issue was the hardware enable was not being
done via ethtool. To resolve this issue and prevent conflicts with VF
configuration we will leave the feature always enabled in hardware, and
then in software we will choose to ignore the results via a sw flag.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally from: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch, both the driver portion and the sctp code was
modified by Jesse Brandeburg and is
Copyright(c) 2009 Intel Corporation.
Thanks go to Vlad for starting this work.
Intel 82576 chipset supports SCTP checksum offloading. This
patch enables this functionality in the driver. A new NETIF
feature is introduced for SCTP checksum offload. If the driver
supports CRC32c checksum, it can set this feature flag. The
hardware can offload both transmit and receive.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of these drivers do a check to verify ip_summed is set to
CHECKSUM_UNNECESSARY prior to passing the packet to GRO. GRO itself
already does such a check so it is redundant and can be removed as this
will likely cause out of order issues when receiving a packet that didn't
pass checksum validation.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was being incorrectly setup to only allow disabling receive
checksum if multiqueue was disabled. This change corrects that so that
RXCSUM is configured regardless of queue configuration.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was switching between adapter->itr containing the EITR value
and the number of interrupts per second. This resulted in high latencies
being seen after brining the interface down and then back up. To resolve
the issue the itr value will now only contain the value that should be
programmed into EITR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out that the Intel wired ethernet drivers do not need to
wake the tx queue since netif_carrier_on/off will take care of the qdisc
management in order to guarantee the correct handling of the transmit
routine enable state.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is currently dumping a message in the log about failing to
allocate vf data when max_vfs is equal to 0. This change makes it so the
error message is only displayed if we set max_vfs to a non zero value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the sysfs entry num_vfs which was added to support
enabling pci virtual functions for 82576.
To prevent VFs from loading automatically a module parameter "max_vfs" was
added so that the number of VFs per PF can be limited. This is especially
useful when 4 or more 82576 ports are on the system because otherwise to
load all VFs would result in 8 interface per physical port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: Fix
Yinghai Lu found one system with 82575EB where, in the kernel that is
kexeced, probe igb failed with -2, the reason being that the adapter
could not be brought back from D3 by the kexec kernel, most probably
due to quirky hardware (it looks like the same behavior happened on
forcedeth).
Prevent igb from putting the adapter into D3 during shutdown except
when we going to power off the system. For this purpose, seperate
igb_shutdown() from igb_suspend() and use the appropriate PCI PM
callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An issue was seen on suspend in which the system reported a page fault. This
was due to the new reg_idx code being called after the queues were freed.
This update prevents any for loops from going through the queues by setting
the number of queues to 0 when they are freed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is on PCIe link trained as x2 the driver is currently reporting
link width as "unknown". The original patch provided by Myron adds the x2
link support and my changes are cosmetic to clean up the readability of the
conditional operators.
Based on work by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was using map_single to map the skbs and then unmap_page to
unmap them. This update changes that so instead uses skb_dma_map and
skb_dma_unmap.
In addition the next_to_watch member of the buffer_info struct was being
set uneccesarily. I removed the spots where it was set without being needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if there are no multicast addresses programmed into the PF then
the VFs cannot have their multicast filters reset. This change makes it so
the code path that updates vf multicast is always called along with the pf
updates.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb was previously setting up all of the timer members itself. It is
easier to just call setup_timer and reduce the calls to one line.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes IGB_DESC_UNUSED and replaces it with a function call
instead in order to cleanup some of the ugliness introduced by the macro.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 82575 is fed 802.1q packets, it chokes with
an error of the form:
igb 0000:08:00.1 partial checksum but proto=81!
As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.
There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out with the correct hardware checksum.
Thanks to Kand Ly <kand@riverbed.com> for discovering the
issue and the coming up with a solution. This patch is
based upon his work.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L0s workaround should be moved into a pci quirk and so it is not
necessary in the driver. This update removes the L0s workaround from the
igb driver.
This was the second half of the PCI quirk patch that Matthew Wilcox did
not pick up when he picked up the quirk patch.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 82576 copper adapter and necessary code to restrict wol for
quad port adapter to first port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding device id to support 82576NS dual port copper
NIC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a typo that was doing a less than comparison instead of
a left shift due to the fact that I didn't get enough <'s in there.
This resolves an issue in which vlans were not functioning correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Pf to pool if adding a VLVF register value and the VFTA bit is
already set.
This patch addresses the unlikely situation that the PF adds a vlan
entry when the vlvf is full, and a vf later adds the vlan to the vlvf.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
