This became dead code with commit 309bd8ed46 ("drm/i915: Reinstate
GMBUS and AUX interrupts on gen4/g4x").
v2: Move comment about HW behavior to where decision is made to enable
MSI (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180523180435.18042-1-lucas.demarchi@intel.com
commit b2209e62a4 ("drm/i915/execlists: Reset the CSB head tracking on
reset/sanitization") and commit 1288786b18 ("drm/i915: Move GEM sanitize
from resume_early to resume") show the conflicting requirements on the
code. We must reset the GPU before trashing live state on a fast resume
(hibernation debug, or error paths), but we must only reset our state
tracking iff the GPU is reset (or power cycled). This is tricky if we
are disabling GPU reset to simulate broken hardware; we reset our state
tracking but the GPU is left intact and recovers from its stale state.
v2: Again without the assertion for forcewake, no longer required since
commit b3ee09a4de ("drm/i915/ringbuffer: Fix context restore upon reset")
as the contexts are reset from the CS ensuring everything is powered up.
Fixes: b2209e62a4 ("drm/i915/execlists: Reset the CSB head tracking on reset/sanitization")
Fixes: 1288786b18 ("drm/i915: Move GEM sanitize from resume_early to resume")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616202534.18767-1-chris@chris-wilson.co.uk
This should be a no-op in terms of our control flow, we move the
sanitization (GPU reset) from the bottom of the early resume phase to
the top of the next. However, following hibernation debug, the power
code skips the early resume phase, but as we are about to completely
restore the GTT mappings, we first need to stop the GPU using them i.e.
perform a GPU reset (i915_gem_sanitize()).
Testcase: igt/gem_exec_suspend/basic-S4-devices
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614094103.18025-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Due to a silent conflict (silent because we are trying to fix the CI
test that is meant to exercising these failures!) between commit
51e645b665 ("drm/i915: Mark the GPU as wedged without error on fault
injection") and commit 8571a05a9d ("drm/i915: Use GEM suspend when
aborting initialisation"), we failed to actually squash the error
message after injecting the load failure.
Rearrange the code to export i915_load_failure() for better logging of
real errors (and quiet logging of injected errors).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180609111058.2660-1-chris@chris-wilson.co.uk
Setting PCH type to PCH_NOP before checking whether we actually have a
PCH ends up returning true for HAS_PCH_SPLIT() on all non-PCH split
platforms. Fix this by using PCH_NOP only for platforms that actually
have a PCH.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608123330.31003-6-jani.nikula@intel.com
Use intel_pch_type() also for mapping the no PCH case (PCH id 0) to
PCH_NONE to simplify code.
Also make sure that intel_pch_type() knows all the PCH ids returned by
intel_virt_detect_pch(). Loudly fail if this isn't the case; this
shouldn't happen anyway.
Cc: Colin Xu <Colin.Xu@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Colin Xu <Colin.Xu@intel.com>
Reviewed-by: Colin Xu <Colin.Xu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608123330.31003-4-jani.nikula@intel.com
Virtualized non-PCH systems such as Broxton or Geminilake should use
PCH_NONE to indicate no PCH rather than PCH_NOP. The latter is a
specific case to indicate a PCH system without south display.
Reported-by: Colin Xu <Colin.Xu@intel.com>
Cc: Colin Xu <Colin.Xu@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Colin Xu <Colin.Xu@intel.com>
Reviewed-by: Colin Xu <Colin.Xu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608123330.31003-2-jani.nikula@intel.com
When we reach the magic value and do inject a fault into our module load,
mark the module option as being hit. Since we fail from inside pci
probe, the module load isn't actually aborted and the module (and
parameters) are left lingering. igt can then inspect the parameter on its
synchronous completion of modprobe to see if the fault injection was
successful, and will keeping on injecting new faults until the module
succeeds in loading having surpassed the number of fault points.
v2: Reset to 0 after being hit;
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180606144153.4244-1-chris@chris-wilson.co.uk
We should keep i915_gem_init/fini functions together for easier
tracking of their symmetry.
v2: rebased, pulled out from the series
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180604090032.20840-1-michal.wajdeczko@intel.com
This patch adds the support to detect PCH_ICP.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180522002558.29262-10-paulo.r.zanoni@intel.com
During testing we encounter a conflict between SUSPEND_TEST_DEVICES and
disabling reset (gem_eio/suspend). This results in the device continuing
on without being reset, but since it has gone through HW sanitization to
account for the suspend/resume cycle, we have to assume the device has
been reset to its defaults. A simple way around this is to skip the
sanitize phase for SUSPEND_TEST_DEVICES by moving it to suspend-late.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180531082246.9763-4-chris@chris-wilson.co.uk
In order to prepare the GPU for sleeping, we may want to submit commands
to it. This is a complicated process that may even require some swapping
in from shmemfs, if the GPU was in the wrong state. As such, we need to
do this preparation step synchronously before the rest of the system has
started to turn off (e.g. swapin fails if scsi is suspended).
Fortunately, we are provided with a such a hook, pm_ops.prepare().
v2: Compile cleanup
v3: Fewer asserts, fewer problems?
v4: Ville pointed out that in some circumstances (such as switching off
the overlay) the display code may issue a GPU request. This is
unexpected, and will result in us going to sleep with us believing the
GPU is still awake (though all user work has been saved). Add a comment
to remind our future selves of what trouble brews.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106640
Testcase: igt/drv_suspend after igt/gem_tiled_swapping
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525092629.1456-1-chris@chris-wilson.co.uk
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Unsafe module parameters are just that, unsafe. If the user is foolish
enough to try them and the kernel breaks, they get to keep both pieces.
Don't ask them to file a bug report if they broke it themselves.
References: https://bugs.freedesktop.org/show_bug.cgi?id=106423
Fixes: d15d7538c6 ("drm/i915: Tune down init error message due to failure injection")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180506183147.2690-1-chris@chris-wilson.co.uk
If we try to suspend a wedged device following a GPU reset failure, we
will also fail to turn off the rc6 powerwells (on vlv), leading to a
*ERROR*. This is quite expected in this case, so the best we can do is
shake our heads and reduce the *ERROR* to a debug so CI stops
complaining.
Testcase: igt/gem_eio/in-flight-suspend #vlv
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105583
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180409094905.4516-1-chris@chris-wilson.co.uk
-----BEGIN PGP SIGNATURE-----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=SkQU
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.17-rc2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Exynos, i915, vc4, amdgpu fixes.
i915:
- an oops fix
- two race fixes
- some gvt fixes
amdgpu:
- dark screen fix
- clk/voltage fix
- vega12 smu fix
vc4:
- memory leak fix
exynos just drops some code"
* tag 'drm-fixes-for-v4.17-rc2' of git://people.freedesktop.org/~airlied/linux: (23 commits)
drm/amd/powerplay: header file interface to SMU update
drm/amd/pp: Fix bug voltage can't be OD separately on VI
drm/amd/display: Don't program bypass on linear regamma LUT
drm/i915: Fix LSPCON TMDS output buffer enabling from low-power state
drm/i915/audio: Fix audio detection issue on GLK
drm/i915: Call i915_perf_fini() on init_hw error unwind
drm/i915/bios: filter out invalid DDC pins from VBT child devices
drm/i915/pmu: Inspect runtime PM state more carefully while estimating RC6
drm/i915: Do no use kfree() to free a kmem_cache_alloc() return value
drm/exynos: exynos_drm_fb -> drm_framebuffer
drm/exynos: Move dma_addr out of exynos_drm_fb
drm/exynos: Move GEM BOs to drm_framebuffer
drm: Fix HDCP downstream dev count read
drm/vc4: Fix memory leak during BO teardown
drm/i915/execlists: Clear user-active flag on preemption completion
drm/i915/gvt: Add drm_format_mod update
drm/i915/gvt: Disable primary/sprite/cursor plane at virtual display initialization
drm/i915/gvt: Delete redundant error message in fb_decode.c
drm/i915/gvt: Cancel dma map when resetting ggtt entries
drm/i915/gvt: Missed to cancel dma map for ggtt entries
...
We have to cleanup after i915_perf_init(), even on the error path, as it
passes a pointer into the module to the sysfs core. If we fail to
unregister the sysctl table, we leave a dangling pointer which then may
explode anytime later.
Fixes: 9f9b2792b6 ("drm/i915/perf: reuse timestamp frequency from device info")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180414091233.32224-1-chris@chris-wilson.co.uk
(cherry picked from commit 9f172f6fbd)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We have to cleanup after i915_perf_init(), even on the error path, as it
passes a pointer into the module to the sysfs core. If we fail to
unregister the sysctl table, we leave a dangling pointer which then may
explode anytime later.
Fixes: 9f9b2792b6 ("drm/i915/perf: reuse timestamp frequency from device info")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180414091233.32224-1-chris@chris-wilson.co.uk
-----BEGIN PGP SIGNATURE-----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=T++R
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- move pci_uevent_ers() out of pci.h (Michael Ellerman)
- skip ASPM common clock warning if BIOS already configured it (Sinan
Kaya)
- fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)
- remove last user of pci_get_bus_and_slot() and the function itself
(Sinan Kaya)
- add decoding for 16 GT/s link speed (Jay Fang)
- add interfaces to get max link speed and width (Tal Gilboa)
- add pcie_bandwidth_capable() to compute max supported link bandwidth
(Tal Gilboa)
- add pcie_bandwidth_available() to compute bandwidth available to
device (Tal Gilboa)
- add pcie_print_link_status() to log link speed and whether it's
limited (Tal Gilboa)
- use PCI core interfaces to report when device performance may be
limited by its slot instead of doing it in each driver (Tal Gilboa)
- fix possible cpqphp NULL pointer dereference (Shawn Lin)
- rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
hotplug (Mika Westerberg)
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space. This is fairly intrusive and includes minor changes to
interfaces used for I/O space on most platforms (Zhichang Yuan, John
Garry)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
- don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
ia64, and mn10300 with x86 (Bjorn Helgaas)
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
- use generic pci_mmap_resource_range() instead of powerpc and xtensa
arch-specific versions (David Woodhouse)
- support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)
- remove System and Video ROM reservations on sparc (Bjorn Helgaas)
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization
(KarimAllah Ahmed)
- consolidate VPD code in vpd.c (Bjorn Helgaas)
- add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
- add DT support for R-Car r8a7743 (Biju Das)
- fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
bridge driver that causes a general protection fault (Dexuan Cui)
- fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
(Dexuan Cui)
- fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
(Dexuan Cui)
- make several structures static (Fengguang Wu)
- increase number of MSI IRQs supported by Synopsys DesignWare bridges
from 32 to 256 (Gustavo Pimentel)
- implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
API from DesignWare drivers (Gustavo Pimentel)
- add Tegra power management support (Manikanta Maddireddy)
- add Tegra loadable module support (Manikanta Maddireddy)
- handle 64-bit BARs correctly in endpoint support (Niklas Cassel)
- support optional regulator for HiSilicon STB (Shawn Guo)
- use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)
- support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)
* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
fm10k: Report PCIe link properties with pcie_print_link_status()
net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
net/mlx5: Report PCIe link properties with pcie_print_link_status()
net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
PCI: Add pcie_print_link_status() to log link speed and whether it's limited
PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
misc: pci_endpoint_test: Handle 64-bit BARs properly
PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
...
Currently, we rely on inspecting the hangcheck state from within the
i915_reset() routines to determine which engines were guilty of the
hang. This is problematic for cases where we want to run
i915_handle_error() and call i915_reset() independently of hangcheck.
Instead of relying on the indirect parameter passing, turn it into an
explicit parameter providing the set of stalled engines which then are
treated as guilty until proven innocent.
While we are removing the implicit stalled parameter, also make the
reason into an explicit parameter to i915_reset(). We still need a
back-channel for i915_handle_error() to hand over the task to the locked
waiter, but let's keep that its own channel rather than incriminate
another.
This leaves stalled/seqno as being private to hangcheck, with no more
nefarious snooping by reset, be it whole-device or per-engine. \o/
The only real issue now is that this makes it crystal clear that we
don't actually do any testing of hangcheck per se in
drv_selftest/live_hangcheck, merely of resets!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406220354.18911-2-chris@chris-wilson.co.uk
If we are resetting just one engine, we know it has stalled. So we can
pass the stalled parameter directly to i915_gem_reset_engine(), which
alleviates the necessity to poke at the generic engine->hangcheck.stalled
magic variable, leaving that under control of hangcheck as its name
implies. Other than simplifying by removing the indirect parameter along
this path, this allows us to introduce new reset mechanisms that run
independently of hangcheck.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406220354.18911-1-chris@chris-wilson.co.uk
We don't handle resetting the kernel context very well, or presumably any
context executing its breadcrumb commands in the ring as opposed to the
batchbuffer and flush. If we trigger a device reset twice in quick
succession while the kernel context is executing, we may end up skipping
the breadcrumb. This is really only a problem for the selftest as
normally there is a large interlude between resets (hangcheck), or we
focus on resetting just one engine and so avoid repeatedly resetting
innocents.
Something to try would be a preempt-to-idle to quiesce the engine before
reset, so that innocent contexts would be spared the reset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180330131801.18327-1-chris@chris-wilson.co.uk
After
commit dd9f31c7a3
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Aug 16 17:46:07 2017 +0300
drm/i915/gen9+: Set same power state before hibernation image
save/restore
during hibernation/suspend the power domain functionality got disabled,
after which resume could leave it incorrectly disabled if the ACPI
target state was S0 during suspend and i915 was not loaded by the loader
kernel.
This was caused by not considering if we resumed from hibernation as the
condition for power domains reiniting.
Fix this by simply tracking if we suspended power domains during system
suspend and reinit power domains accordingly during resume. This will
result in reiniting power domains always when resuming from hibernation,
regardless of the platform and whether or not i915 is loaded by the
loader kernel.
The reason we didn't catch this earlier is that the enabled/disabled
state of power domains during PMSG_FREEZE/PMSG_QUIESCE is platform
and kernel config dependent: on my SKL the target state is S4
during PMSG_FREEZE and (with the driver loaded in the loader kernel)
S0 during PMSG_QUIESCE. On the reporter's machine it's S0 during
PMSG_FREEZE but (contrary to this) power domains are not initialized
during PMSG_QUIESCE since i915 is not loaded in the loader kernel, or
it's loaded but without the DMC firmware being available.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105196
Reported-and-tested-by: amn-bas@hotmail.com
Fixes: dd9f31c7a3 ("drm/i915/gen9+: Set same power state before hibernation image save/restore")
Cc: amn-bas@hotmail.com
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322143642.26883-1-imre.deak@intel.com
(cherry picked from commit 0f90603c33)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
After
commit dd9f31c7a3
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Aug 16 17:46:07 2017 +0300
drm/i915/gen9+: Set same power state before hibernation image
save/restore
during hibernation/suspend the power domain functionality got disabled,
after which resume could leave it incorrectly disabled if the ACPI
target state was S0 during suspend and i915 was not loaded by the loader
kernel.
This was caused by not considering if we resumed from hibernation as the
condition for power domains reiniting.
Fix this by simply tracking if we suspended power domains during system
suspend and reinit power domains accordingly during resume. This will
result in reiniting power domains always when resuming from hibernation,
regardless of the platform and whether or not i915 is loaded by the
loader kernel.
The reason we didn't catch this earlier is that the enabled/disabled
state of power domains during PMSG_FREEZE/PMSG_QUIESCE is platform
and kernel config dependent: on my SKL the target state is S4
during PMSG_FREEZE and (with the driver loaded in the loader kernel)
S0 during PMSG_QUIESCE. On the reporter's machine it's S0 during
PMSG_FREEZE but (contrary to this) power domains are not initialized
during PMSG_QUIESCE since i915 is not loaded in the loader kernel, or
it's loaded but without the DMC firmware being available.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105196
Reported-and-tested-by: amn-bas@hotmail.com
Fixes: dd9f31c7a3 ("drm/i915/gen9+: Set same power state before hibernation image save/restore")
Cc: amn-bas@hotmail.com
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322143642.26883-1-imre.deak@intel.com
We were fetching uC firmwares in separate uc_init_fw step, while
there is no reason why we can't fetch them during init_early.
This will also simplify upcoming patches, as size of the firmware
may be used for register initialization.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323123451.59244-2-michal.wajdeczko@intel.com
In upcoming patch, we want to perform more actions in early
initialization of the uC. This reordering will help resolve
new dependencies that will be introduced by future patch.
v2: s/i915_gem_load_init/i915_gem_init_early (Chris)
v3: s/i915_gem_load_cleanup/i915_gem_cleanup_early (Michal)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323123451.59244-1-michal.wajdeczko@intel.com
We try to keep all HuC related code in dedicated file.
There is no need to peek HuC register directly during
handling getparam ioctl.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314200429.40132-1-michal.wajdeczko@intel.com
Not all callers want the GPU error to handled in the same way, so expose
a control parameter. In the first instance, some callers do not want the
heavyweight error capture so add a bit to request the state to be
captured and saved.
v2: Pass msg down to i915_reset/i915_reset_engine so that we include the
reason for the reset in the dev_notice(), superseding the earlier option
to not print that notice.
v3: Stash the reason inside the i915->gpu_error to handover to the direct
reset from the blocking waiter.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320100449.1360-2-chris@chris-wilson.co.uk
In Gen11, the Video Decode engines (aka VDBOX, aka VCS, aka BSD) and the
Video Enhancement engines (aka VEBOX, aka VECS) could be fused off. Also,
each VDBOX and VEBOX has its own power well, which only exist if the
related engine exists in the HW.
Unfortunately, we have a Catch-22 situation going on: we need the blitter
forcewake to read the register with the fuse info, but we cannot initialize
the forcewake domains without knowin about the engines present in the HW.
We workaround this problem by allowing the initialization of all forcewake
domains and then pruning the fused off ones, as per the fuse information.
Bspec: 20680
v2: We were shifting incorrectly for vebox disable (Vinay)
v3: Assert mmio is ready and warn if we have attempted to initialize
forcewake for fused-off engines (Paulo)
v4:
- Use INTEL_GEN in new code (Tvrtko)
- Shorter local variable (Tvrtko, Michal)
- Keep "if (!...) continue" style (Tvrtko)
- No unnecessary BUG_ON (Tvrtko)
- WARN_ON and cleanup if wrong mask (Tvrtko, Michal)
- Use I915_READ_FW (Michal)
- Use I915_MAX_VCS/VECS macros (Michal)
v5: Rebased by Rodrigo fixing conflicts on top of:
"drm/i915: Simplify intel_engines_init"
v6: Fix v5. Remove info->num_rings. (by Oscar)
v7: Rebase (Rodrigo).
v8:
- s/intel_device_info_fused_off_engines/
intel_device_info_init_mmio (Chris)
- Make vdbox_disable & vebox_disable local variables (Chris)
v9:
- Move function declaration to intel_device_info.h (Michal)
- Missing indent in bit fields definitions (Michal)
- When RC6 is enabled by BIOS, the fuse register cannot be read until
the blitter powerwell is awake. Shuffle where the fuse is read, prune
the forcewake domains after the fact and change the commit message
accordingly (Vinay, Sagar, Chris).
v10:
- Improved commit message (Sagar)
- New line in header file (Sagar)
- Specify the message in fw_domain_reset applies to ICL+ (Sagar)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316121456.11577-1-mika.kuoppala@linux.intel.com
[Mika: soothe checkpatch on commit msg]
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Those two concepts are really separate. Since GuC is writing data into
its own buffer and we even provide a way for userspace to read directly
from it using i915_guc_log_dump debugfs, there's no real reason to tie
log level with relay creation.
Let's create a separate debugfs, giving userspace a way to create a
relay on demand, when it wants to read a continuous log rather than a
snapshot.
v2: Don't touch guc_log_level on relay creation error, adjust locking
after rebase, s/dev_priv/i915, pass guc to file->private_data (Sagar)
Use struct_mutex rather than runtime.lock for set_log_level
v3: Tidy ordering of definitions (Sagar)
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319095348.9716-5-michal.winiarski@intel.com
If we fail to reset the GPU, we declare the machine wedged. However, the
GPU may well still be running in the background with an in-flight
request. So despite our efforts in cleaning up the request queue and
faking the breadcrumb in the HWSP, the GPU may eventually write the
in-flght seqno there breaking all of our assumptions and throwing the
driver into a deep turmoil, wedging beyond wedged.
To avoid this we ideally want to reset the GPU. Since that has already
failed, make sure the rings have the stop bit set instead. This is part
of the normal GPU reset sequence, but that is actually disabled by
igt/gem_eio to force the wedged state. If we assume the worst, we must
poke at the bit again before we give up.
v2: Move the intel_gpu_reset() from set-wedged in the reset error path
into i915_gem_set_wedged() itself. Even if the reset fails (e.g. if it is
disabled by gem_eio), it still tries to make sure the engines are
stopped. For i915_gem_set_wedged() callers from outside of i915_reset(),
this should make sure the GPU is disabled while the driver is marked as
being wedged.
Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315151015.22741-1-chris@chris-wilson.co.uk
Hardware may have specific restrictions on GuC WOPCM offset and size. On
Gen9, the value of the GuC WOPCM size register needs to be larger than the
value of GuC WOPCM offset register + a Gen9 specific offset (144KB) for
reserved GuC WOPCM. Fail to enforce such a restriction on GuC WOPCM size
will lead to GuC firmware execution failures. On the other hand, with
current static GuC WOPCM offset and size values (512KB for both offset and
size), the GuC WOPCM size verification will fail on Gen9 even if it can be
fixed by lowering the GuC WOPCM offset by calculating its value based on
HuC firmware size (which is likely less than 200KB on Gen9), so that we can
have a GuC WOPCM size value which is large enough to pass the GuC WOPCM
size check.
This patch updates the reserved GuC WOPCM size for RC6 context on Gen9 to
24KB to strictly align with the Gen9 GuC WOPCM layout. It also adds support
to verify the GuC WOPCM size aganist the Gen9 hardware restrictions. To
meet all above requirements, let's provide dynamic partitioning of the
WOPCM that will be based on platform specific HuC/GuC firmware sizes.
v2:
- Removed intel_wopcm_init (Ville/Sagar/Joonas)
- Renamed and Moved the intel_wopcm_partition into intel_guc (Sagar)
- Removed unnecessary function calls (Joonas)
- Init GuC WOPCM partition as soon as firmware fetching is completed
v3:
- Fixed indentation issues (Chris)
- Removed layering violation code (Chris/Michal)
- Created separat files for GuC wopcm code (Michal)
- Used inline function to avoid code duplication (Michal)
v4:
- Preset the GuC WOPCM top during early GuC init (Chris)
- Fail intel_uc_init_hw() as soon as GuC WOPCM partitioning failed
v5:
- Moved GuC DMA WOPCM register updating code into intel_wopcm.c
- Took care of the locking status before writing to GuC DMA
Write-Once registers. (Joonas)
v6:
- Made sure the GuC WOPCM size to be multiple of 4K (4K aligned)
v8:
- Updated comments and fixed naming issues (Sagar/Joonas)
- Updated commit message to include more description about the hardware
restriction on GuC WOPCM size (Sagar)
v9:
- Minor changes variable names and code comments (Sagar)
- Added detailed GuC WOPCM layout drawing (Sagar/Michal)
- Refined macro definitions to be reader friendly (Michal)
- Removed redundent check to valid flag (Michal)
- Unified first parameter for exported GuC WOPCM functions (Michal)
- Refined the name and parameter list of hardware restriction checking
functions (Michal)
v10:
- Used shorter function name for internal functions (Joonas)
- Moved init-ealry function into c file (Joonas)
- Consolidated and removed redundant size checks (Joonas/Michal)
- Removed unnecessary unlikely() from code which is only called once
during boot (Joonas)
- More fixes to kernel-doc format and content (Michal)
- Avoided the use of PAGE_MASK for 4K pages (Michal)
- Added error log messages to error paths (Michal)
v11:
- Replaced intel_guc_wopcm with more generic intel_wopcm and attached
intel_wopcm to drm_i915_private instead intel_guc (Michal)
- dynamic calculation of GuC non-wopcm memory start (a.k.a WOPCM Top
offset from GuC WOPCM base) (Michal)
- Moved WOPCM marco definitions into .c source file (Michal)
- Exported WOPCM layout diagram as kernel-doc (Michal)
v12:
- Updated naming, function kernel-doc to align with new changes (Michal)
v13:
- Updated the ordering of s-o-b/cc/r-b tags (Sagar)
- Corrected one tense error in comment (Sagar)
- Corrected typos and removed spurious comments (Joonas)
Bspec: 12690
Signed-off-by: Jackie Li <yaodong.li@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: John Spotswood <john.a.spotswood@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com> (v8)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v9)
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> (v11)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v12)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520987574-19351-2-git-send-email-yaodong.li@intel.com
We are sanitizing uC related modparams together with other driver
modparams in intel_sanitize_options called from i915_driver_init_hw,
but this is too late for us as we will want to use USES_GUC/USES_HUC
macros at earlier stage. Since our sanitizing does not require any
MMIO access, we can do it in intel_uc_init_early right after we resolve
firmware names.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312130308.22952-2-michal.wajdeczko@intel.com
We have many functions responsible for allocating different parts of
GuC log runtime called from multiple places. Let's stick with keeping
everything in guc_log_register instead.
v2: Use more generic intel_uc_register name, keep using "misc" suffix (Michał)
s/dev_priv/i915 (Sagar)
Make guc_log_relay_* static (sparse)
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308154707.21716-2-michal.winiarski@intel.com
There are a number of information that are readable from hardware
registers and that we would like to make accessible to userspace. One
particular example is the topology of the execution units (how are
execution units grouped in subslices and slices and also which ones
have been fused off for die recovery).
At the moment the GET_PARAM ioctl covers some basic needs, but
generally is only able to return a single value for each defined
parameter. This is a bit problematic with topology descriptions which
are array/maps of available units.
This change introduces a new ioctl that can deal with requests to fill
structures of potentially variable lengths. The user is expected fill
a query with length fields set at 0 on the first call, the kernel then
sets the length fields to the their expected values. A second call to
the kernel with length fields at their expected values will trigger a
copy of the data to the pointed memory locations.
The scope of this uAPI is only to provide information to userspace,
not to allow configuration of the device.
v2: Simplify dispatcher code iteration (Tvrtko)
Tweak uapi drm_i915_query_item structure (Tvrtko)
v3: Rename pad fields into flags (Chris)
Return error on flags field != 0 (Chris)
Only copy length back to userspace in drm_i915_query_item (Chris)
v4: Use array of functions instead of switch (Chris)
v5: More comments in uapi (Tvrtko)
Return query item errors in length field (All)
v6: Tweak uapi comments style to match the coding style (Lionel)
v7: Add i915_query.h (Joonas)
v8: (Lionel) Change the behavior of the item iterator to report
invalid queries into the query item rather than stopping the
iteration. This enables userspace applications to query newer
items on older kernels and only have failure on the items that are
not supported.
v9: Edit copyright headers (Joonas)
v10: Typos & comments in uapi (Joonas)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306122857.27317-6-lionel.g.landwerlin@intel.com
Up to now, subslice mask was assumed to be uniform across slices. But
starting with Cannonlake, slices can be asymmetric (for example slice0
has different number of subslices as slice1+). This change stores all
subslices masks for all slices rather than having a single mask that
applies to all slices.
v2: Rework how we store total numbers in sseu_dev_info (Tvrtko)
Fix CHV eu masks, was reading disabled as enabled (Tvrtko)
Readability changes (Tvrtko)
Add EU index helper (Tvrtko)
v3: Turn ALIGN(v, 8) / 8 into DIV_ROUND_UP(v, BITS_PER_BYTE) (Tvrtko)
Reuse sseu_eu_idx() for setting eu_mask on CHV (Tvrtko)
Reformat debug prints for subslices (Tvrtko)
v4: Change eu_mask helper into sseu_set_eus() (Tvrtko)
v5: With Haswell reporting masks & counts, bump sseu_*_eus() functions
to use u16 (Lionel)
v6: Fix sseu_get_eus() for > 8 EUs per subslice (Lionel)
v7: Change debugfs enabels for number of subslices per slice, will
need a small igt/pm_sseu change (Lionel)
Drop subslice_total field from sseu_dev_info, rely on
sseu_subslice_total() to recompute the value instead (Lionel)
v8: Remove unused function compute_subslice_total() (Lionel)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306122857.27317-2-lionel.g.landwerlin@intel.com
We want to use higher level 'uc' functions as the main entry points to
the GuC/HuC code to hide some details and keep code layered.
While here, move call to disable_guc_interrupts after sending suspend
action to the GuC to allow it work also with CTB as comm mechanism.
v2: update commit msg (Sagar)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302111550.21328-1-michal.wajdeczko@intel.com
We want to de-emphasize the link between the request (dependency,
execution and fence tracking) from GEM and so rename the struct from
drm_i915_gem_request to i915_request. That is we may implement the GEM
user interface on top of requests, but they are an abstraction for
tracking execution rather than an implementation detail of GEM. (Since
they are not tied to HW, we keep the i915 prefix as opposed to intel.)
In short, the spatch:
@@
@@
- struct drm_i915_gem_request
+ struct i915_request
A corollary to contracting the type name, we also harmonise on using
'rq' shorthand for local variables where space if of the essence and
repetition makes 'request' unwieldy. For globals and struct members,
'request' is still much preferred for its clarity.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221095636.6649-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Getting ready to remove pci_get_bus_and_slot() function in favor of
pci_get_domain_bus_and_slot().
Extract the domain number from drm_device and pass it into
pci_get_domain_bus_and_slot() function.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Rather than deriving the platform_mask from the
intel_device_static_info->platform at runtime, pre-fill it in the static
data.
v2: Undefine macros at end of their scope
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215081930.11477-3-chris@chris-wilson.co.uk
Add an intel_bios_cleanup() function to act as counterpart of
intel_bios_init() and move the cleanup of vbt related resources there,
putting it in the same file as the allocation.
Changed in v2:
-While touching the code anyways, remove the unnecessary:
if (dev_priv->vbt.child_dev) done before kfree(dev_priv->vbt.child_dev)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214082151.25015-1-hdegoede@redhat.com
Simplify intel_virt_detect_pch() by making it return a PCH id rather
than returning the PCH type and setting PCH id for some PCHs. Map the
PCH id to PCH type using the shared routine. This gives us sanity check
on the supported combinations also in the virtualized setting.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/197cf635261a1c628371ffaaee90e8647493af4d.1517851783.git.jani.nikula@intel.com
If we fail to reset the GPU (i915_reset()), we do one final
intel_gpu_reset() attempt as we mark the device wedged. The idea here is
even though the GPU has proven unreliable (and so we want to stop using
it for the time being), we don't want it spinning away in the background
whilst the driver idles so we try to reset it one more time. However, we
want to dump the i915_gem_set_wedged() debugging info before we do, so
that we can see the accurate state of the GPU when it failed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180209114056.9957-1-chris@chris-wilson.co.uk
Most of our ioctl functions have an _ioctl suffix in the name. I like
that idea since it makes it easy to figure out how the function is
going to get called. Rename the handful of exceptions to follow the
same pattern.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180207164841.19431-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Rather than having the high level ioctl interface guess the underlying
implementation details, having the implementation declare what
capabilities it exports. We define an intel_driver_caps, similar to the
intel_device_info, which instead of trying to describe the HW gives
details on what the driver itself supports. This is then populated by
the engine backend for the new scheduler capability field for use
elsewhere.
v2: Use caps.scheduler for validating CONTEXT_PARAM_SET_PRIORITY (Mika)
One less assumption of engine[RCS] \o/
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tomasz Lis <tomasz.lis@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180207210544.26351-2-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
On blb and pnv, we are seeing sporadic
i915 0000:00:02.0: Resetting chip after gpu hang
[drm:intel_gpu_reset [i915]] rcs0: timed out on STOP_RING
[drm:i915_reset [i915]] *ERROR* Failed hw init on reset -5
which notably lack the actual root cause of the error. Ostensibly it
should be the init_ring_common() that failed, but it's error paths are
covered by DRM_ERROR.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180207111545.17078-1-chris@chris-wilson.co.uk
