This change makes the tx and rx config a bit cleaner by breaking out the ring
specific configuration from the generic rx and tx configuration.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This update increases the minimum rx buffer size to 1K. The reason for this
change is to support SR-IOV and avoid any conflicts with the rings being able
to set their own MTU sizes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Counting packets with a good checksum can cause a significant amount of cache
line bouncing due to the shared counter being written to by all of the queues.
In order to avoid this I am removing the counter since we still have the
checksum failed counter which will tell us if there are any issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new igb_q_vector data structure to handle interrupts and NAPI. This
helps to abstract the rings away from the adapter struct. In addition it
allows for a bit of consolidation since a tx and rx ring can share a
q_vector.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove duplicate atl1c_get_tpd, it may cause hardware to send wrong packets.
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few new country codes and update the regulatory domain for some
countries.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'COEX_PRIORITY_TABLE_CMD' host command will be supported for 5000 series
and up.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add unconditional call to apm_ops.stop() to reset device to low power state
when unloading driver. Some paths have existed to unload driver *without*
resetting device, therefore some errors have persisted through multiple
load/unload cycles, until the whole platform gets rebooted; this is an
attempt to remedy some of those situations. Sorry, I can't seem to find
a bughost.org bug that specifically has these symptoms, but I had it happen
recently here.
Note that this will *not* fix situations in which the PCI express bus has
crashed (evidenced by register reads showing "0xffffffff"), e.g. bughost.org
1855 and 2096; device is unreachable from driver in those cases.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x00 and 6x50 series devices, APIv4 is the lowest firmware version
driver can support. This is also the lowest API version available to the
public so there is no need for backward compatibility support for the
earlier API versions.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Duplicated define for listen interval (IWL_CONN_MAX_LISTEN_INTERVAL and
IWL_CONN_LISTEN_INTERVAL), remove IWL_CONN_LISTEN_INTERVAL
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Reported-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For notification packets and SKBs that fail to rx correctly, add
them back into the rx_free list so that the pages can be reused
later. This avoids allocating new rx pages unnecessarily.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
parameters "len" is not used in both iwl_tx_queue_free() and
iwl_cmd_queue_free() functions
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX_FREE_BUFFERS and RX_LOW_WATERMARK are currently defined in four places.
Based on how files are included we only need the definition in iwl-fh.h
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Frans Pop <elendil@planet.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support "channel switch" request by issue "channel switch" host command
to uCode.
There is no separated "channel switch" indication from mac80211,
when detected "IEEE80211_CONF_CHANGE_CHANNEL" flag in iwl_mac_config(),
if the station is in "associated" state, then assume "channel switch
announcement" IE was received by mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using device configuration structure to decide how to configure
ct_kill host command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using device configuration structure to decide the type of thermal
throttle method for the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase the size of TFD_MAX_PAYLOAD_SIZE (the size of iwl_device_cmd)
to accommodate iwl6000_channel_switch_cmd data structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the paged rx patch (4854fde2), I introduced a bug that could possibly
touch an already freed page. It is fixed by avoiding the access in this
patch. I've also added some comments so that other people touching the
code won't make the same mistake. In the future, if we cannot avoid
access the page after being handled to the upper layer, we can use
get_page/put_page to handle it. For now, it's just not necessary.
It also fixed a debug message print bug reported by Stanislaw Gruszka
<sgruszka@redhat.com>.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specify both Tx and Rx chain in device configuration structure instead
of hard code in set_hw_params() for 4965
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Detach led background task from statistic notification routine. if led
blinking is required; the blink rate is based on the traffic condition.
It do not relate to statistics notification. In addition to that, there is
not a requirement for statistics notification has to occur all the time.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate most iwlXXXX_apm_init() functions into single iwl_apm_init().
Keep iwl3945_apm_init(), but leverage iwl_apm_init() for most functionality.
Update 4965 init sequence to follow most recent factory recommendations.
Add following members to struct iwl_cfg to guide the init sequence:
pll_cfg_val (replaces needs_pll_cfg), set_l0s, use_bsm
Move L0S enable/disable from nic_config() functions to iwl_apm_init().
This satisifies the "FIXME: put here L1A -L0S w/a" notice, and complies
with factory-recommended sequence.
Add debug info message in iwl_apm_init(), and symmetrical message
in iwl_apm_stop().
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In Rx gain balancing (chain noise) computation for 5000 series and up,
the delta gain calculation should use the average noise of default
chain, not "chain 0" which do not exist for all the devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two commands missing from list of commands such that when debug is
enabled, these commands are shown as UNKNOWN.
Missing commands are TX_ANT_CONFIGURATION_CMD and
TEMPERATURE_NOTIFICATION.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... in pursue to quaff the wide-spread references to WEXT constants.
When setting SNMP_MIB_OID_BSS_TYPE, wext.c can directly calculate the value
the firmware wants.
Reading of SNMP_MIB_OID_BSS_TYPE doesn't happen anywhere, so no need to
convert the firmware value into WEXT values anyway.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This now makes decl.h only contain declarations for functions that don't
have their own *.h file.
No function change.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... because for cfg80211 we'll need a completely different
implementation.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was only used as a source for S_DS_GEN, but the size of this struct
is equal to the size of "struct cmd_header".
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... which just resided as an old-style command in cmd/cmdresp, but
was nowhere useed. If we ever need it, we can re-add it as a newstyle
command.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... which just resided as an old-style command in cmd/cmdresp, but
was nowhere useed. If we ever need it, we can re-add it as a newstyle
command.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... because it's purely a WEXT function.
No functional change.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That's because the new cfg80211 implementation will provide cleaner
implementations.
No functional changes.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... as priv->curbssparams won't exist once libertas+cfg80211 lands.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having the variables in logical groups allows us to easier
#ifdef stuff out.
No functional change.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another cfg80211-preparation patch: removes some code/definitions from
main.c and dev.h and put's it into assoc.c/.h, scan.c/.h.
No function change.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the 11d code was protected with an "if (priv->enable11d)" clause.
But there was no code that anywhere that was able to set this
variable to true. So all 11d code was dead for almost a year and no one
complained. That's enought incentive to remove this code.
Besides removing old cruft, we gain back the 11d capability in a common way
when we merge the cfg80211 functionality.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
First, we reduce the number of hardware retries to 0 (ie 2 real retries
for each rate). Next, when we report the retries to mac80211, we always
report a retry count of 1 (it seems to be 2 in fact, but using 2 seems
to lead to wrong performance for some reason). We use a state machine to
determine the real fate of a packet based on the 802.11 ACK and what the
Zydas hardware is saying when a real retry occurs. The real retry rates
are encoded in a static array. It has been tested with both zd1211 and
zd1211b hardware. Of course, since the Zydas hardware is not reporting
retries accurately, we are just doing our best in order to get the best
performance (ie higher throughput).
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new ieee80211_rx_ni() function instead of ieee80211_rx(). Since we
use a workqueue to handle the RX path, we need to call the new function,
which disables bottom half handling. This patch fixes the NOHZ:
local_softirq_pending messages.
CC: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the mesh housekeeping timer work properly on big endian
systems.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current A-MPDU tx_status report mechanism is too inaccurate.
With this patch BlockACK frames show now up to the driver and
can be processed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch follows "ar9170: atomic pending A-MPDU counter"
idea and converts another critical counter to atomic_*.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A ref-counting bug emerged after testing ar9170usb's HT
implementation on a bigger SMP/SMT system without the usual
_debugging_ overhead.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For static power save, the actual intervals are calculated by driver based on
the default table and DTIM flag, then sent to uCode when the scheme
is changed.
Three tables are defined based on DTIM period.
1. DTIM 0 - 2
2. DTIM 3 - 10
3. DTIM > 11
The actual number of DTIM a station may miss may not exceed the
following:
. Only 1 DTIM may be skipped at PI=4 when allowed
. Only 2 DTIMs may be skipped at PI=5 when allowed
. DTIM may be skipped only 5 sec after last activity
. DTIM may be skipped only 30 sec after connection establishment
Only allow user to override the power_level when rf is ready to make sure
power level gets changed upon request.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For initial bring up of 6x50 series NICs, no chain noise support in
uCode, this feature will be added in the later stage of development.
Two chain noise related functions are removed from 6x50 series:
1. gain computation
2. chain noise reset
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x00 and 6x50 series NIC with OTP shadow RAM, set auto clock gate
disable bit when initializing OTP access.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 initializes the rate scaling before notifying the driver
of the station's existence. The driver dealt with this by not relying on
mac80211's station notifications and instead mixing this functionality with
the rate scaling code and other places. To clean this up the driver needs
to do rate scaling initialization after being notified of the station, this
can be done if the rate scaling information forms part of the station
information passed from mac80211 to driver.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move to header file so they can be included and used in other parts of the
driver.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
