After the worker thread is launched, bind function is doing further
configuration. In case of failure stop the thread.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sanjay Singh Rawat <snjsrwt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is an "&&" vs "||" typo here so this loops 3000 times or if we get
unlucky it could loop forever.
Fixes: ceaa0a6eea ('usb: gadget: m66592-udc: add support for TEST_MODE')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We handle the "if (!req->req.length)" condition at the start of the
function and return. We can delete this dead code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
apq8016-sbc board is using Dual SPDT USB Switch (TC7USB40MU),
witch is controlled by GPIO to de/multiplex D+/D- USB lines to
USB2513B Hub and uB connector. Add support for this.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace calls of gadget_supports_altsettings() function (which check altset
support by comparing UDC controller name with hardcoded names) with
gadget_is_altset_supported() which checks generic quirk bitfield.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use generic mechanism to check if UDC controller supports zlp.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use generic mechanism to check if UDC controller supports stalling.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to some UDC controllers may not support zlp, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_zlp_not_supp' field to struct usb_gadget and helper
function gadget_is_zlp_supported(). It also sets 'quirk_zlp_not_supp'
to 1 in musb UDC driver, which has such limitation.
[ balbi@ti.com : make it build ]
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to some UDC controllers may not support stalling, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_stall_not_supp' field to struct usb_gadget and helper
function gadget_is_stall_supported(). It also sets 'quirk_stall_not_supp'
to 1 in at91_udc driver, which has such limitation.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to some UDC controllers may not support altsettings, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_altset_not_supp' field to struct usb_gadget and helper
function gadget_is_altset_supported(). It also sets 'quirk_altset_not_supp'
to 1 in pxa25x_udc and pxa27x_udc drivers, which have such limitation.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use chained TRB mechanism to handle non maxpacket aligned transfers
greater than bounce buffer size. With this the first TRB will be programmed
to receive 'ALIGN(ur->length - maxp, maxp)' data and the second TRB
will be programmed to receive the remaining data using bounce buffer.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add chained TRB support to ep0. Now TRB's can be chained just by
invoking _dwc3_ep0_start_trans_ with 'chain' parameter set to true.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Added a new parameter in _dwc3_ep0_start_trans_ to
indicate whether the TRB is a chained TRB or last TRB. This is in
preparation for adding chained TRB support for ep0.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. This is in preparation for handling non maxpacket
aligned transfers greater than bounce buffer size. This is basically to
avoid code duplication when using chained TRB transfers to handle
non maxpacket aligned transfers greater than bounce buffer size.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Used _roundup_ macro to calculate the transfer
size aligned to maxpacket in dwc3_ep0_complete_data. It also makes it
similar to how transfer size is calculated in __dwc3_ep0_do_control_data.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 uses bounce buffer to handle non max packet aligned OUT transfers and
the size of bounce buffer is 512 bytes. However if the host initiates OUT
transfers of size more than 512 bytes (and non max packet aligned), the
driver throws a WARN dump but still programs the TRB to receive more than
512 bytes. This will cause bounce buffer to overflow and corrupt the
adjacent memory locations which can be fatal.
Fix it by programming the TRB to receive a maximum of DWC3_EP0_BOUNCE_SIZE
(512) bytes.
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These changes allow a PHY driver to trigger a VBUS interrupt and
to provide the value of VBUS.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
ether unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
composite unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate usb otg descriptor and initialize it according to gadget's otg
capabilities, if usb_otg_caps is not set, keep settings as current gadget
drivers. With this 2 new interfaces, gadget can use usb_otg_descriptor
for OTG 1.x, and usb_otg20_descriptor for OTG 2.0 or above, and otg
features can be decided by the combination of usb hardware property
and driver config.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After introduce usb otg properties, update ci_otg_is_fsm_mode conditions
to be depending on both usb hardware properties and usb driver config,
also resolve a compile issue in debug.c after the API change.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Init and update otg capabilities by DT, set gadget's otg capabilities
accordingly.
Acked-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Check property of usb hardware to update otg version and disable SRP, HNP
and ADP if its disable flag is present.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Copy usb_otg_descriptor from config's descriptor if host requests
USB_DT_OTG.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The A33 SoC uses the same musb controller as found on the A31 and later,
but allwinner has removed the configdata register, this commit adds special
handling for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The A31 SoC uses the same musb controller as found in earlier SoCs, but it
is hooked up slightly different. Its SRAM is private and no longer controlled
through the SRAM controller, and its reset is controlled via a separate
reset controller. This commit adds support for this setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is based on initial code to get the Allwinner sunxi musb controller
supported by Chen-Yu Tsai and Roman Byshko.
This adds support for the Allwinner sunxi musb controller in both host only
and otg mode. Peripheral only mode is not supported, as no boards use that.
This has been tested on a cubietruck (A20 SoC) and an UTOO P66 tablet
(A13 SoC) with a variety of devices in host mode and with the g_serial gadget
driver in peripheral mode, plugging otg / host cables in/out a lot of times
in all possible imaginable plug orders.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind(). Field 'can_activate' in struct f_obex is no longer
needed as setting 'bind_deactivated' flag makes us sure, that the function
will be binded only if deactivation can be performed successfully.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces 'bind_deactivated' flag in struct usb_function.
Functions which don't want to be activated automatically after bind should
set this flag, and when they start to be ready to work they should call
usb_function_activate().
When USB function sets 'bind_deactivated' flag, initial deactivation
counter is incremented automatically, so there is no need to call
usb_function_deactivate() in function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using usb_gadget_disconnect to make gadget temporarily invisible to host
doesn't provide desired result, because gadget is connected immediately
after binding regardless to previous usb_gadget_disconnect() calls.
For this reason we use usb_gadget_deactivate() instead of
usb_gadget_disconnect() to make it working as expected.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Driver handles PHY initialization, clock management, power
management and workarounds required after resetting the hardware.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass storage spec allows up to 16 LUNs, so let's not
add some more restrictive limits.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
EXPORT_SYMBOL_GPL() is usually placed after function definition
not before.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Creation of LUN 0 may fail (for example due to ENOMEM).
As fsg_common_set_num_buffers() does some memory allocation
we should free it before it becomes unavailable.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We have a "Enabling %s" trace when enabling an endpoint
but that message felt lonely without a matching
"Disabling %s". Add it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a SoC supports both PHY interfaces but
doesn't define HSPHY in DT/pdata, we will get
an unnecessary dev_warn() which can mislead users
into thinking that they're missing something.
Instead, let's just silently rely on a correct
default. If the HW default is wrong, then HSPHY
is required and USB won't work, this will be
motivation enough for engineers to patch their
way into a working setup.
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Currently this parameter is made optional with the help of a cpp trick.
To allow dropping this hack convert callers to explictly pass a value
for flags.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this additional parameter and the _optional variant to simplify the
driver and improve error handling. Also expand the comment to explain
why it's not sensible to switch to devm_gpiod_get and why the gpiod_put
is also necessary.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).
Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the deprecated API of extcon and then use the new extcon API
with the unique id to indicate the each external connector (USB-HOST).
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Varka Bhadram <varkab@cdac.in>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch uses the devm_extcon_dev_[allocate|register]() to manage the
resource automatically and replace deprecated API as following:
- extcon_[set|get]_cable_state(*edev, char *) -> extcon_[set|get]_cable_state_(*edev, id)
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).
Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)
[ balbi@ti.com : fix build break ]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).
Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In big endian cases, the macro cpu_to_le{16,32} unfolds to __swab{16,32}
which provides special case for constants. In little endian cases,
__constant_cpu_to_le{16,32} and cpu_to_le{16,32} expand directly to
the same expression. So, replace __constant_cpu_to_le{16,32} with
cpu_to_le{16,32} with the goal of getting rid of the definition of
__constant_cpu_to_le{16,32} completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
(
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
|
- __constant_cpu_to_le32(x)
+ cpu_to_le32(x)
)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I18N should be spelled as i18n because it's not
an acronym
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In big endian cases, macro cpu_to_le16 unfolds to __swab16 which
provides special case for constants. In little endian cases,
__constant_cpu_to_le16 and cpu_to_le16 expand directly to the
same expression. So, replace __constant_cpu_to_le16 with
cpu_to_le16 with the goal of getting rid of the definition of
__constant_cpu_to_le16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As SourceSink function has been reworked for ConfigFS
composite gadget this comment is no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As loopback function has been reworked for ConfigFS
composite gadget this comment is no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that we have no users of dev_dbg() in dwc3,
we can safely remove CONFIG_USB_DWC3_DEBUG.
If dev_dbg() is ever strictly necessary - and I
don't see why it would, considering we want to
rely on tracepoints for debug - we will depend
on DYNAMIC_PRINTK to enable such messages.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the mode of operation is exposed through debugfs
at all times. Because of that, we're removing
the unnecessary messages.
Signed-off-by: Felipe Balbi <balbi@ti.com>
those two messages are informing that the clock
doesn't exist; that, however, is a valid situation
and driver continues just fine by ignoring the error.
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
that message is informing that the clock is missing.
However, that's a valid condition for some setups; driver
even ignores the error and continues just fine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's just a lot clearer to use | operator instead of
+ operator.
Caught by coccicheck:
"
drivers/usb/dwc2/gadget.c:2883:26-27: WARNING: sum of probable
bitmasks, consider |
"
Cc: John Youn <John.Youn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds removable mass storage support to g_nokia gadget (for N900).
It means that at runtime block device can be exported or unexported.
So it does not export anything by default and thus allows to use MyDocs
partition as before...
[ balbi@ti.com: make it build ]
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
An incorrect definition of CCR_PM_USBPW3 in ohci-tmio.c is a perennial
source of invalid diagnoses from static scanners, such as in
<http://marc.info/?l=linux-usb&m=143634574527641&w=2>. This patch
fixes the definition.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Binderman <dcb314@hotmail.com>
CC: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grain-media GM12U320 based devices are mini video projectors using USB for
both power and video data transport.
Their usb-storage interface is a virtual windows driver CD.
The gm12u320 kms driver needs these interfaces to talk to the device and
export it as framebuffer & kms dri device nodes, so make sure that the
usb-storage driver does not bind to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device automatically switches itself to another mode (0x1405)
unless the specific access pattern of Windows is followed in its
initial mode. That makes a dirty unmount of the internal storage
devices inevitable if they are mounted. So the card reader of
such a device should be ignored, lest an unclean removal become
inevitable.
This replaces an earlier patch that ignored all LUNs of this device.
That patch was overly broad.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Reviewed-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug introduced by commit 977dcfdc60 ("USB: OHCI:
don't lose track of EDs when a controller dies"). The commit changed
ed_state from ED_UNLINK to ED_IDLE too early, before finish_urb() had
been called. The user-visible consequence is that the driver
occasionally crashes or locks up when an URB is submitted while
another URB for the same endpoint is being unlinked.
This patch moves the ED state change later, to the right place. The
drawback is that now we may unnecessarily execute some instructions
multiple times when a controller dies. Since controllers dying is an
exceptional occurrence, a little wasted time won't matter.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Heiko Przybyl <lil_tux@web.de>
Tested-by: Heiko Przybyl <lil_tux@web.de>
Fixes: 977dcfdc60
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 25cd2882e2 ("usb/xhci: Change how we indicate a host supports
Link PM.") removed the code to set lpm_capable for USB 3.0 super-speed
root hub. The intention of that change was to avoid touching usb core
internal field, a.k.a. lpm_capable, and let usb core to set it by
checking U1 and U2 exit latency values in the descriptor.
Usb core checks and sets lpm_capable in hub_port_init(). Unfortunately,
root hub is a special usb device as it has no parent. Hub_port_init()
will never be called for a root hub device. That means lpm_capable will
by no means be set for the root hub. As the result, lpm isn't functional
at all in Linux kernel.
This patch add the code to check and set lpm_capable when registering a
root hub device. It could be back-ported to kernels as old as v3.15,
that contains the Commit 25cd2882e2 ("usb/xhci: Change how we indicate
a host supports Link PM.").
Cc: stable@vger.kernel.org # 3.15
Reported-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port link change with port in resume state should not be
reported to usbcore, as this is an internal state to be
handled by xhci driver. Reporting PLC to usbcore may
cause usbcore clearing PLC first and port change event irq
won't be generated.
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the link is just waken, it's in Resume state, and driver sets PLS to
U0. This refers to Phase 1. Phase 2 refers to when the link has completed
the transition from Resume state to U0.
With the fix of xhci: report U3 when link is in resume state, it also
exposes an issue that usb3 roothub and controller can suspend right
after phase 1, and this causes a hard hang in controller.
To fix the issue, we need to prevent usb3 bus suspend if any port is
resuming in phase 1.
[merge separate USB2 and USB3 port resume checking to one -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_hub_report_usb3_link_state() returns pls as U0 when the link
is in resume state, and this causes usb core to think the link is in
U0 while actually it's in resume state. When usb core transfers
control request on the link, it fails with TRB error as the link
is not ready for transfer.
To fix the issue, report U3 when the link is in resume state, thus
usb core knows the link it's not ready for transfer.
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When resetting a device the number of active TTs may need to be
corrected by xhci_update_tt_active_eps, but the number of old active
endpoints supplied to it was always zero, so the number of TTs and the
bandwidth reserved for them was not updated, and could rise
unnecessarily.
This affected systems using Intel's Patherpoint chipset, which rely on
software bandwidth checking. For example, a Lenovo X230 would lose the
ability to use ports on the docking station after enough suspend/resume
cycles because the bandwidth calculated would rise with every cycle when
a suitable device is attached.
The correct number of active endpoints is calculated in the same way as
in xhci_reserve_bandwidth.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Campbell <bacam@z273.org.uk>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
virt_dev->num_cached_rings counts on freed ring and is not updated
correctly. In xhci_free_or_cache_endpoint_ring() function, the free ring
is added into cache and then num_rings_cache is incremented as below:
virt_dev->ring_cache[rings_cached] =
virt_dev->eps[ep_index].ring;
virt_dev->num_rings_cached++;
here, free ring pointer is added to a current index and then
index is incremented.
So current index always points to empty location in the ring cache.
For getting available free ring, current index should be decremented
first and then corresponding ring buffer value should be taken from ring
cache.
But In function xhci_endpoint_init(), the num_rings_cached index is
accessed before decrement.
virt_dev->eps[ep_index].new_ring =
virt_dev->ring_cache[virt_dev->num_rings_cached];
virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL;
virt_dev->num_rings_cached--;
This is bug in manipulating the index of ring cache.
And it should be as below:
virt_dev->num_rings_cached--;
virt_dev->eps[ep_index].new_ring =
virt_dev->ring_cache[virt_dev->num_rings_cached];
virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL;
Cc: <stable@vger.kernel.org>
Signed-off-by: Aman Deep <aman.deep@samsung.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI in Intel CherryView / Braswell Platform requires
a driver workaround to get xHCI D3 working. Without this
workaround, xHCI might not enter D3.
Workaround is to configure SSIC PORT as "unused" before D3
entry and "used" after D3 exit. This is done through a
vendor specific register (PORT2_SSIC_CONFIG_REG2 at offset
0x883c), in xhci suspend / resume callbacks.
Verified xHCI D3 works fine in CherryView / Braswell platform.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel xhci hw that require XHCI_PME_STUCK quirk have as default disabled
xhci from going to D3 state in runtime suspend. Driver needs to verify
it can deal with the hw by calling an ACPI _DSM method to get D3 enabled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue introduced in commit b23c843992 (usb: dwc3:
gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would
only use DEPSTARTCFG once per SetConfig.
The trick is that we should use one DEPSTARTCFG per SetConfig *OR*
SetInterface. SetInterface was completely missed from the original
patch.
This problem became aparent after commit 76e838c9f7 (usb: dwc3:
gadget: return error if command sent to DEPCMD register fails)
added checking of the return status of device endpoint commands.
'Set Endpoint Transfer Resource' command was caught failing
occasionally. This is because the Transfer Resource
Index was not getting reset during a SET_INTERFACE request.
Finally, to fix the issue, was we have to do is make sure that
our start_config_issued flag gets reset whenever we receive a
SetInterface request.
To verify the problem (and its fix), all we have to do is run
test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'.
Tested-by: Huang Rui <ray.huang@amd.com>
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Fixes: b23c843992 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dma_map_single and dma_unmap_single should set "gadget->dev.parent"
instead of "&gadget->dev" in the first argument because the parent has
a udc controller's device pointer.
Otherwise, iommu functions are not called in ARM environment.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was an omission in transition to devm_xxx resource handling.
iounmap(udc->phy_regs) were removed, but ioremap() was left
without devm_.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 3517c31a8e ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Phy drivers and the ulpi interface providers depend on the
registration of the ulpi bus. Ulpi registers the bus in
module_init(). This could cause unnecessary bus users'
probe delays. i.e. unnecessary -EPROBE_DEFER happening on
ulpi_drivers in case they're registered before ulpi bus
itself.
Reported-by: Zhuo Qiuxu <qiuxu.zhuo@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some modules call config_item_init_type_name() and config_group_init_type_name()
with parameter "name" directly controlled by userspace. These two
functions call config_item_set_name() with this name used as a format
string, which can be used to leak information such as content of the
stack to userspace.
For example, make_netconsole_target() in netconsole module calls
config_item_init_type_name() with the name of a newly-created directory.
This means that the following commands give some unexpected output, with
configfs mounted in /sys/kernel/config/ and on a system with a
configured eth0 ethernet interface:
# modprobe netconsole
# mkdir /sys/kernel/config/netconsole/target_%lx
# echo eth0 > /sys/kernel/config/netconsole/target_%lx/dev_name
# echo 1 > /sys/kernel/config/netconsole/target_%lx/enabled
# echo eth0 > /sys/kernel/config/netconsole/target_%lx/dev_name
# dmesg |tail -n1
[ 142.697668] netconsole: target (target_ffffffffc0ae8080) is
enabled, disable to update parameters
The directory name is correct but %lx has been interpreted in the
internal item name, displayed here in the error message used by
store_dev_name() in drivers/net/netconsole.c.
To fix this, update every caller of config_item_set_name to use "%s"
when operating on untrusted input.
This issue was found using -Wformat-security gcc flag, once a __printf
attribute has been added to config_item_set_name().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's an idr memory-leak fix and a couple of new device ids.
Included is also a build fix for mos7720 on the mn10300 architecture,
which has a register with the same name as one of the driver defines.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=K/L7
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.2-rc2
Here's an idr memory-leak fix and a couple of new device ids.
Included is also a build fix for mos7720 on the mn10300 architecture,
which has a register with the same name as one of the driver defines.
Signed-off-by: Johan Hovold <johan@kernel.org>
In case kstrdup() fails the resources to release are
midi->in_port[] and midi. No cards have been registered,
so no need to unregister any.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Triggering suspend to RAM via sysfs on a i.MX28 causes a NULL pointer
dereference. This patch avoids the oops in mxs_phy_get_vbus_status()
by aborting since there is no syscon available.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: efdbd3a5d6 ("usb: phy: mxs: do not set PWD.RXPWD1PT1 for low speed connection")
CC: <stable@vger.kernel.org> # 4.0
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
My static checker detected the mistake. I fix this by changing "goto
err_irq" to "goto err_req". The label err_irq is not used now
so this patch also removes it.
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit f563d23090 ("usb: gadget: composite: add req_match method
to usb_function") accesses cdev->config even before set config
is invoked causing a NULL pointer dereferencing error while running
Lecroy Mass Storage Compliance test.
Fix it here by accessing cdev->config only if it is non NULL.
Fixes: commit f563d23090 ("usb: gadget: composite: add req_match
method to usb_function").
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
do not try to set cancel function in synchronous operations in
ffs_epfile_{read,write}_iter.
Cc: <stable@vger.kernel.org> # v4.0+
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass storage function created via configfs always reports eight LUNs
to the hosts even if only one LUN has been configured. Adjust the
number when the USB function is allocated based on LUNs that user
has created.
Cc: <stable@vger.kernel.org>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 3e10a2ce98 ("usb: dwc3: add hsphy_interface
property") introduced a possible NULL pointer
dereference because dwc->hsphy_interface can be
NULL.
In order to fix it, all we have to do is guard
strncmp() against a NULL argument.
Fixes: 3e10a2ce98 ("usb: dwc3: add hsphy_interface property")
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Register backup function can be called from atomic context. Instead
of using atomic memory pool, embed backup storage space in
struct dwc2_hsotg.
Also add a valid flag in each struct as NULL pointer can't be used as
the content validity check any more.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To avoid sleep while atomic bugs, allocate qtd before calling
dwc2_hcd_urb_enqueue. No need to pass mem_flags to
dwc2_hcd_urb_enqueue any more as no memory allocations are done in it.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To avoid sleep while atomic bugs, allocate qh before calling
dwc2_hcd_urb_enqueue. qh pointer can be used directly now instead of
passing ep->hcpriv as double pointer.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently, we're calling musb_start() twice for DRD ports
in some situations. This has been observed to cause enumeration
issues after suspend/resume cycles with AM335x.
In order to fix the problem, we just have to fix the check
on musb_has_gadget() so that it only returns true if
current mode is Host and ignore the fact that we have or
not a gadget driver loaded.
Fixes: ae44df2e21 (usb: musb: call musb_start() only once in OTG mode)
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <stable@vger.kernel.org> # v3.11+
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
