Coldfire still provides its own variant of the clk API rather than using
the generic COMMON_CLK API. This generally works, but it causes some
link errors with drivers using the clk_round_rate(), clk_set_rate(),
clk_set_parent(), or clk_get_parent() functions when a platform lacks
those interfaces.
This adds empty stub implementations for each of them, and I don't even
try to do something useful here but instead just print a WARN() message
to make it obvious what is going on if they ever end up being called.
The drivers that call these won't be used on these platforms (otherwise
we'd get a link error today), so the added code is harmless bloat and
will warn about accidental use.
Based on commit bd7fefe1f0 ("ARM: w90x900: normalize clk API").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The ColdFire PCI configuration space access functions swap addressing
regions to do their work. Just letting the read/write cycles exit
the CPU core (via the ColdFire "nop" instruction) is not enough to
guarantee that the address region remapping has actually completed.
Insert a read back of the mapping register to be absolutely sure
that the remapping has completed.
This fixes an occasional boot hang during the ColdFire PCI initialization
phase.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
All the ColdFire IO access support code has been moved to io_no.h.
This means that all ColdFire support is at least now consistent no
matter whether the MMU is enabled or not for them.
Now that io_mm.h has reverted to only support the traditional m68k MMU
enabled processors we can remove the ColdFire specific definitions.
We can also remove the old ColdFire PCI bus IO access functions.
The new io_no.h uses asm-generic/io.h to provide all the basic support.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
As of commit 205e1b7f51 ("dma-mapping: warn when there is no
coherent_dma_mask") the Freescale FEC driver is issuing the following
warning on driver initialization on ColdFire systems:
WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516 0x40159e20
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc7-dirty #4
Stack from 41833dd8:
41833dd8 40259c53 40025534 40279e26 00000003 00000000 4004e514 41827000
400255de 40244e42 00000204 40159e20 00000009 00000000 00000000 4024531d
40159e20 40244e42 00000204 00000000 00000000 00000000 00000007 00000000
00000000 40279e26 4028d040 40226576 4003ae88 40279e26 418273f6 41833ef8
7fffffff 418273f2 41867028 4003c9a2 4180ac6c 00000004 41833f8c 4013e71c
40279e1c 40279e26 40226c16 4013ced2 40279e26 40279e58 4028d040 00000000
Call Trace:
[<40025534>] 0x40025534
[<4004e514>] 0x4004e514
[<400255de>] 0x400255de
[<40159e20>] 0x40159e20
[<40159e20>] 0x40159e20
It is not fatal, the driver and the system continue to function normally.
As per the warning the coherent_dma_mask is not set on this device.
There is nothing special about the DMA memory coherency on this hardware
so we can just set the mask to 32bits in the platform data for the FEC
ethernet devices.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Add support for Sysam stmark2 board, an open hardware embedded
Linux board, see http://sysam.it/cff_stmark2.html for any info.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
This patch adds initial module base address and irq for dspi0.
It also defines the dspi0 clock to be used by the Freescale driver.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The M54[78]x ColdFire parts are not the only members of the ColdFire family
that have an MMU. But currently some of the early MMU initialization code
is inside the startup code specific to only the ColdFire M54[78]x parts.
Move that early ColdFire MMU init code so that it is run for other ColdFire
parts running with MMU enabled.
Specifically this means that the MMU initialization code will now also be
run for the ColdFire M5441x parts when running with MMU enabled.
The code move meant that the extern definition for the mmu_context_init()
function had to be moved as well. To make it clear that is ColdFire specific
I have renamed that with a "cf_" in front of it and put its extern definition
in the mcfmmu.h (which is already included by the setup code).
Reported-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull m68knommu updates from Greg Ungerer:
"Only two changes. One removes unused code, the other makes local clock
code arguments consistent with generic clock code"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: remove dead code
m68k: allow NULL clock for clk_get_rate
As CONFIG_RTC_DRV_M5441x doesn't exist because the driver never made it
upstream, there is no device to register. Remove code that is never
compiled and init_BSP() as it doesn't do anything.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: facdf0ed4f ("m68knommu: introduce basic clk infrastructure")
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-kernel@vger.kernel.org
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The pci_fixup_irqs() function allocates IRQs for all PCI devices present in
a system; those PCI devices possibly belong to different PCI bus trees (and
possibly rooted at different host bridges) and may well be enabled (ie
probed and bound to a driver) by the time pci_fixup_irqs() is called when
probing a given host bridge driver.
Furthermore, current kernel code relying on pci_fixup_irqs() to assign
legacy PCI IRQs to devices does not work at all for hotplugged devices in
that the code carrying out the IRQ fixup is called at host bridge driver
probe time, which just cannot take into account devices hotplugged after
the system has booted.
The introduction of map/swizzle function hooks in struct pci_host_bridge
allows us to define per-bridge map/swizzle functions that can be used at
device probe time in PCI core code to allocate IRQs for a given device
(through pci_assign_irq()).
Convert PCI host bridge initialization code to the
pci_scan_root_bus_bridge() API (that allows to pass a struct
pci_host_bridge with initialized map/swizzle pointers) and remove the
pci_fixup_irqs() call from arch code.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Make the code like the rest of the kernel.
Link: http://lkml.kernel.org/r/14db9c166d5b68efa77e337cfe49bb9b29bca3f7.1499284835.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the m68k arch's coldfire clockevent driver initialize these fields
properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Add support for Sysam AMCORE board, an open hardware embedded Linux
board, see http://sysam.it/openzone/projects/amcore/amcore.html for
any info.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
These changes based on work by Steven King <sfking@fdwdc.com> to support
the i2c hardware modules on ColdFire SoC family devices.
This is the per SoC hardware support. Contains a common platform device
setup. Each of the SoC family members tends to have some minor local
setup required to initialize the module. But all ColdFire family members
use the same i2c hardware module.
This i2c hardware module is the same as used in the Freescale iMX ARM
based family of SoC devices. Steven's original patches were based on using
a new and different i2c-coldfire.c driver. But this is not neccessary as
we can use the existing Linux i2c-imx.c driver with no change required to
it. And this patch is now based on using the existing i2c-imx driver.
This patch only contains the ColdFire platform changes.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
In many of clk_disable() implementations, it is a no-op for a NULL
pointer input, but this is one of the exceptions.
Making it treewide consistent will allow clock consumers to call
clk_disable() without NULL pointer check.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The early ColdFire bootmem_alloc() code is currently only included in
the board support for the Coldire 54xx platforms. It will be used on all
ColdFire MMU enabled platforms as others are supported. So move the
mcf54xx_bootmem_alloc() function to be generally available to all MMU
enabled ColdFire parts (and use a more generic name for it).
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Not all ColdFire SoC parts that have an MMU also have an FPU - so set
an FPU type (via m68k_fputype) appropriate for the configured platform.
With this set correctly /proc/cpuinfo will report FPU "none" on devices
that don't have one. And kernel code paths that initialize FPU hardware
will now only execute if an FPU is actually present.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Create a new machine type for platforms based around the ColdFire 5441x
SoC family. Set that machine type on startup when building for this
platform type.
Currently the ColdFire head.S hard codes a M54xx machine type at startup -
since that is the only platform type currently supported with MMU enabled.
The m5441x has an MMU and this change forms part of the support required
to run it with the MMU enabled.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Most ColdFire support code has switched to using IO memory access
methods (readb/writeb/etc) when reading and writing internal peripheral
device registers. The WildFire board specific halt code was missed.
As it is now the WildFire code is broken, since all register definitions
were changed to be register addresses only some time ago.
Fix the WildFire board code to use the appropriate IO access functions.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The early setup code for the ColdFire 53xx platform accesses variables
before the RAM and other system initialization steps may have taken place.
Currently it has 2 global variables that will end up in the bss section
that are accessed during this early setup. There is a special static RAM
stack setup at this time, but not necessarily the RAM where kernel data
sections will end up.
Even on system setups where RAM is setup by a boot loader the access
to the early setup variables is before the BSS section has been initialized.
This can potentially corrupt a ram loaded root filesystem that sits in that
memory area before it has been moved.
These 2 variables are not used at all after being set, and can just be
removed.
Reported-by: Christian Gieseler <christiangieseler@yahoo.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
The ColdFire architecture specific gpio support code registers a sysfs
bus device named "gpio". This clashes with the new generic API device
added in commit 3c702e99 ("gpio: add a userspace chardev ABI for GPIOs").
The old ColdFire sysfs gpio device was never used for anything specific,
and no links or other nodes were created under it. The new API sysfs gpio
device has all the same default sysfs links (device, drivers, etc) and
they are properly populated.
Remove the old ColdFire sysfs gpio registration.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
The FEC (Fast Ethernet Crontroller) module on many ColdFire parts can
be compiled into the kernel, or as a module. Therefore the platform device
support for it is required whenever the driver is enabled - not just when
built into the kernel. Use IS_ENABLED(CONFIG_FEC) instead of a conditional
check on only the driver being built into the kernel.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
We're planning to remove the gpiochip_add() function to swith
to gpiochip_add_data() with NULL for data argument.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
If max_pfn is not initialized, the various /proc/kpage* files are empty,
and selftests/vm/mlock2-tests will fail. max_pfn is also used by the
block layer to calculate DMA masks.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Tested-by: Greg Ungerer <gerg@uclinux.org>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Pull m68k/colfire fixes from Greg Ungerer:
"Only a couple of patches this time. One migrating the clock driver
code to the new set-state interface. The other cleaning up to use the
PFN_DOWN macro"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k/coldfire: use PFN_DOWN macro
m68k/coldfire/pit: Migrate to new 'set-state' interface
Pull networking updates from David Miller:
"Another merge window, another set of networking changes. I've heard
rumblings that the lightweight tunnels infrastructure has been voted
networking change of the year. But what do I know?
1) Add conntrack support to openvswitch, from Joe Stringer.
2) Initial support for VRF (Virtual Routing and Forwarding), which
allows the segmentation of routing paths without using multiple
devices. There are some semantic kinks to work out still, but
this is a reasonably strong foundation. From David Ahern.
3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.
4) Ignore route nexthops with a link down state in ipv6, just like
ipv4. From Andy Gospodarek.
5) Remove spinlock from fast path of act_gact and act_mirred, from
Eric Dumazet.
6) Document the DSA layer, from Florian Fainelli.
7) Add netconsole support to bcmgenet, systemport, and DSA. Also
from Florian Fainelli.
8) Add Mellanox Switch Driver and core infrastructure, from Jiri
Pirko.
9) Add support for "light weight tunnels", which allow for
encapsulation and decapsulation without bearing the overhead of a
full blown netdevice. From Thomas Graf, Jiri Benc, and a cast of
others.
10) Add Identifier Locator Addressing support for ipv6, from Tom
Herbert.
11) Support fragmented SKBs in iwlwifi, from Johannes Berg.
12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.
13) Add BQL support to 3c59x driver, from Loganaden Velvindron.
14) Stop using a zero TX queue length to mean that a device shouldn't
have a qdisc attached, use an explicit flag instead. From Phil
Sutter.
15) Use generic geneve netdevice infrastructure in openvswitch, from
Pravin B Shelar.
16) Add infrastructure to avoid re-forwarding a packet in software
that was already forwarded by a hardware switch. From Scott
Feldman.
17) Allow AF_PACKET fanout function to be implemented in a bpf
program, from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
net: fec: clear receive interrupts before processing a packet
ipv6: fix exthdrs offload registration in out_rt path
xen-netback: add support for multicast control
bgmac: Update fixed_phy_register()
sock, diag: fix panic in sock_diag_put_filterinfo
flow_dissector: Use 'const' where possible.
flow_dissector: Fix function argument ordering dependency
ixgbe: Resolve "initialized field overwritten" warnings
ixgbe: Remove bimodal SR-IOV disabling
ixgbe: Add support for reporting 2.5G link speed
ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
ixgbe: support for ethtool set_rxfh
ixgbe: Avoid needless PHY access on copper phys
ixgbe: cleanup to use cached mask value
ixgbe: Remove second instance of lan_id variable
ixgbe: use kzalloc for allocating one thing
flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
ixgbe: Remove unused PCI bus types
...
An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Migrate m68k driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We weren't doing anything in ->set_mode(RESUME) and so tick_resume()
isn't implemented.
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Pull m68k fixes from Greg Ungerer:
"Nothing big, spelling fixes and fix/cleanup for ColdFire eth device setup"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix fec setup warning for ColdFire 5271 builds
m68knommu: ColdFire 5271 only has a single FEC controller
m68k: Fix trivial typos in comments
Building for the ColdFire 5271 produces the following warning:
arch/m68k/coldfire/m527x.c: In function ‘m527x_fec_init’:
arch/m68k/coldfire/m527x.c:95:6: warning: unused variable ‘par’
Fix it by moving the definition of par inside the 5271 conditional code.
Reported-by: ertheb <3rth3bnospam@ethe.fr>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Previously, pci_scan_bus() created a root PCI bus, enumerated the devices
on it, and called pci_bus_add_devices(), which made the devices available
for drivers to claim them.
Most callers assigned resources to devices after pci_scan_bus() returns,
which may be after drivers have claimed the devices. This is incorrect;
the PCI core should not change device resources while a driver is managing
the device.
Remove pci_bus_add_devices() from pci_scan_bus() and do it after any
resource assignment in the callers.
[bhelgaas: changelog, check for failure in mcf_pci_init()]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
CC: Guan Xuetao <gxt@mprc.pku.edu.cn>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Matt Turner <mattst88@gmail.com>
Picked up by the 0-day buidler:
All warnings:
>> arch/m68k/coldfire/intc-5272.c:46:20: warning: large integer implicitly truncated to unsigned type [-Woverflow]
/*MCF_IRQ_EINT1*/ { .icr = MCFSIM_ICR1, .index = 28, .ack = 1, },
...
The problem stems from the changes to make all ColdFire register addresses
absolute, in commit d72a5abb ("make remaining ColdFire 5272 register
definitions absolute"). That change did not take into account that the
addresses were stored as offsets in the irqmap of the intc-5272.c code.
Make the field that now stores register addresses big enough to hold
addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Quite a few of the ColdFire specific support files have a pathname in the
title comments of the file. These files have moved around a bit over the
years, and most are no longer accurate. Remove the pathname and fix the
comments to include at least a short description of the files contents.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move the m68k ColdFire platform support code directory to be with the
existing m68k platforms. Although the ColdFire is not a platform as such,
we have always kept all its support together. No reason to change that
as this time.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
