Modules: USB generic driver
If we submit all our URBs when a playback stream is started, the first
hwptr_done update for each URB happens at the same time. This results
in an underrun when there isn't enough PCM data available at this
point for all URBs.
To avoid this, we begin submitting our URBs earlier (when the stream
is prepared), with empy packets. When the stream is started, the
prepare_playback_urb() call for each URB will be run only when the
respective URB has completed previously, so the first hwptr_done
updates will be done nicely staggered.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: MIPS AU1x00 driver
AMD Au1x00 ALSA driver fails compilation with the alternate spinlock
implementation because it doesn't do locking/unlocking correctly in some
places (passes spinlock by value).
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: AZT3328 driver
this is now an even much more reworked patch (#3) for my azt3328.c ALSA driver.
IOW I spent another 4 evenings to get the sequencer timer to work properly
(my head is still hurting) and do lots of other cleanups.
Note that despite the extensive sequencer timer additions, the driver object
is still only 2kB bigger than the previous version, due to those many
optimizations...
Changes in version #3:
- fully working ALSA sequencer timer support for the card's 1024000Hz
DirectX timer (downscaling adjustable via seqtimer_scaling module param)
- an insane amount of code optimizations
- many, many cleanups
Changes in version #2:
- FOUND the 1us DirectX timer area (yay!), made the code respect it
properly
- renamed some 'weird' mixer control names according to ControlNames.txt
- cleanup unneeded debug messages, reformatting
- improved I/O register documentation
- constified many more structs
Changes in version #1:
- improves/fixes some fatal playback/recording interaction
- improves IRQ handler performance (and actually fixes some weird code)
- coalesces some I/O accesses
- slightly improves I/O interface documentation
- improves/fixes logging
- defines out some less important debug code
- constifies some data
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: EMU10K1/EMU10K2 driver,Common EMU synth
This patch fixes problems with voices cutting off or not
sounding at all.
Signed-off-by: Tim <tedon@rogers.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HWDEP Midlevel,PCM Midlevel,RawMidi Midlevel,ALSA Core
Replace usage of CONFIG_SND_MAJOR with snd_major, where appropriate.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA Core,ALSA Minor Numbers
Remove the unused and undefined symbols SNDRV_DEVICE_TYPE_{MIXER,
PCM_PLOOP,PCM_CLOOP}, and introduce a new symbol SNDRV_MINOR_GLOBAL
for non-card-specific devices like the sequencer or the timer.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: AD1889 driver,RME9652 driver
This is the sound/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in sound/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use schedule_timeout_{,un}interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time conversion functions instead of hard-coded division to avoid
rounding issues.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
1.In intel8x0_measure_ac97_clock routine, when stop DMA, there is not stop
DMA corectly, but start another PCM In2 DMA engine.
2.In do_ali_reset routine, there is only need to enable PCM IN and PCM OUT.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: Documentation,ALI5451 driver,NM256 driver
Removed multi-card supports for ali5451 and nm256 drivers.
They are supposed to be a single device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: NM256 driver
The current snd-nm256 driver can cause Dell Latitude CSx laptops to
lock-up during module (un)load. I have isolated this to the writes to
the control port register at offset 0x6cc which were not already
protected by the existing reset_workaround.
I tried grouping these writes with the existing reset_workaround
clause, but that caused the driver to have (un)load problems on the
Dell Latitude LS laptops. So, I have implemented a reset_workaround_2
clause (please feel free to suggest a better name!) to cover this
situation and added a quirk entry for the CSx laptops.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
We better pretend that the ymfpci timer runs at 48 kHz because the
interrupt frequency cannot be higher, and clients that would try to
use 96 kHz would run at half their desired speed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA sequencer
When no default timer frequency has been set, initialize_timer() just
uses the maximum frequency supported by the timer, which is ridiculously
high on 96 kHz timers.
This patch introduces a default frequency of 1000 Hz for this case, and
makes sure that a frequency set by the user isn't too high.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Maestro3 driver
This patch fixes the maestro3 driver to call the snd_m3_assp_init
function to write the DSP firmware into the ASSP chip before sending the
RUN_ASSP command, thereby solving the hang after a cold boot.
Signed-off-by: Charles R. Anderson <cra@alum.wpi.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
- Set buggy_irq parameter before registration of irq handler.
- Clean up module parameter handling.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: VIA82xx driver
The change only affects the via823x kind of chips.
Here the via8233_pcm_pointer_hw() function
(named snd_via8233_pcm_pointer() before)
needed to loop until a non zero position is red from the chip.
Measurements have shown that more than 200 loops are typically needed on
an Athlon64.
As io-reads cost many cycles, those loops sum up huge.
via8233_pcm_pointer_hw() runs either in interrupt or with interrupts
disabled. So it introduces significant interrupt latency.
The patch introduces a calculated position value hwptr_done,
that is updated by the interrupt routine when a period is completed.
It is only used, if the 823x chip returns a zero position, which can't
be interpreted reliably.
Further optimisation is applied on the 8233 chip's interrupt routine:
Only the SGD_SHADOW is read, as it contains all infos needed.
We ommit ~5 more register reads that way.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
Remove the usb_reset_configuration() call from the probe callback
because it isn't needed and it may interfere with other drivers
already loaded for the device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: VIA82xx driver
The patch enable separate DXS controls of sound function of VIA VT82xx
controller in case DXS volume is not needed for PCM Playback volume
control emulation.
Signed-off-by: Honza Maly <hkmaly@matfyz.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,MIPS AU1x00 driver,PPC Beep,SPARC DBRI driver
Removed the use of chip_t, which was obsoleted.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Timer Midlevel
Split or rewrite lines that are longer than 80 characters, and remove
whitespaces at the end of lines.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Timer Midlevel
The return value of list_entry() already has the type from the second
argument, so we don't need to typecase it again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: RTC timer driver,Timer Midlevel
Add a module pointer to the timer structure and use it for refcounting
instead of the card's module pointer to prevent the global timer
modules (rtctimer and hpetimer) from being removed while in use.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ES1938 driver
- Clean up the last PM fix
- Add TRIGGER_SUSPEND/RESUME to disable/enable DMA properly during PM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES1938 driver
This patch fixes the suspend/resume issue I'm having with ESS-Solo1
soundcard. Without this patch I might get after resume message
that kernel is disabling the IRQ5 (soundcard). If there was something
playing it wont continue after resume without this patch.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Remove vmalloc wrapper
- Add release_and_free_resource() to remove kfree_nocheck() from each driver
and simplify the code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALSA Core,ALSA<-OSS emulation
Remove a global function snd_task_name(), and move it local
to snd-pcm-oss module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,PCM Midlevel,Timer Midlevel,ALSA Core
Use the standard getnstimeofday() function instead of ALSA's own one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove snd_runtime_check() macro.
This macro worsens the readability of codes. They should be either
normal if() or removable asserts.
Also, the assert displays stack-dump, instead of only the last caller
pointer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
On my Acer Aspire 3003LCi laptop, the speaker volume is not controlled
by the master control, but by the headphone control. Enabling the
'hp_only' quirk corrects this. The patch below adds this device to the
list of known quirks.
Signed-off-by: Dick Streefland <dick@streefland.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ICE1724 driver
Remove the restcition of sample rates on Revolution 7.1 board.
This enables the low 8-44kHz sample rates.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
