Need to use adjusted protocol value for setting inner protocol.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE for IPv6 does not properly translate for GRE flags to tunnel
flags and vice versa. This patch fixes that.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip6gre_tnl_link_config set t->tun_len and t->hlen correctly for the
configuration. For hard_header_len and mtu calculation include
IPv6 header and encapsulation overhead.
In ip6gre_tunnel_init_common set t->tun_len and t->hlen correctly for
the configuration. Revert to setting hard_header_len instead of
needed_headroom.
Tested:
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225
Gives MTU of 1434. That is equal to 1500 - 40 - 14 - 4 - 8.
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225 okey 123
Gives MTU of 1430. That is equal to 1500 - 40 - 14 - 4 - 8 - 4.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c:274:1: warning:
symbol 'socfpga_dwmac_pm_ops' was not declared. Should it be static?
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: l3mdev: Allow send on enslaved interface
First patch preps for the second. The second is required for several use
cases such as ping on an interface and BFD that need to send packets on
a specific interface, including ones enslaved to a VRF device.
v2
- fixed brackets on both patches per comment from DaveM
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow udp and raw sockets to send by oif that is an enslaved interface
versus the l3mdev/VRF device. For example, this allows BFD to use ifindex
from IP_PKTINFO on a receive to send a response without the need to
convert to the VRF index. It also allows ping and ping6 to work when
specifying an enslaved interface (e.g., ping -I swp1 <ip>) which is
a natural use case.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move l3mdev_rt6_dst_by_oif and l3mdev_get_saddr to l3mdev.c. Collapse
l3mdev_get_rt6_dst into l3mdev_rt6_dst_by_oif since it is the only
user and keep the l3mdev_get_rt6_dst name for consistency with other
hooks.
A follow-on patch adds more code to these functions making them long
for inlined functions.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit-bd5a256 introduces a deadlock bug in fjes_change_mtu().
This spin_lock_irqsave() is obviously unnecessary.
This patch eliminates unnecessary spin_lock_irqsave() in
fjes_change_mtu()
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I accidently let Arnd's VXLAN dependency changes slip into net-next,
they are only appropriate for net.
Also the flow steering structural changes to mlx5e_priv got scrambled
during the merge resolution as well.
Fix that all up.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pn533_recv_frame is called from within abort_command
context the current dev->cmd is not guaranteed to be set.
Additionally on receiving an error status we can omit frame
checking and simply schedule the workqueue.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We need to reset the poll modulation list before calling
nfc_targets_found because otherwise userspace could run
before the modulation list is cleared and then get a "Cannot
activate target while polling" error upon calling activate_target.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When a command gets aborted the pn533 core does not need any RX
frames that may be received until a new frame is sent.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Correctly call nfc_set_parent_dev before nfc_register_device.
Otherwise the driver will OOPS when being removed.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The requested irq needs to be freed when removing the driver,
otherwise a following driver load fails to request the irq.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- bug in ahash SG list walking that may lead to crashes
- resource leak in qat
- missing RSA dependency that causes it to fail"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: rsa - select crypto mgr dependency
crypto: hash - Fix page length clamping in hash walk
crypto: qat - fix adf_ctl_drv.c:undefined reference to adf_init_pf_wq
crypto: qat - fix invalid pf2vf_resp_wq logic
Pull networking fixes from David Miller:
1) Check klogctl failure correctly, from Colin Ian King.
2) Prevent OOM when under memory pressure in flowcache, from Steffen
Klassert.
3) Fix info leak in llc and rtnetlink ifmap code, from Kangjie Lu.
4) Memory barrier and multicast handling fixes in bnxt_en, from Michael
Chan.
5) Endianness bug in mlx5, from Daniel Jurgens.
6) Fix disconnect handling in VSOCK, from Ian Campbell.
7) Fix locking of netdev list walking in get_bridge_ifindices(), from
Nikolay Aleksandrov.
8) Bridge multicast MLD parser can look at wrong packet offsets, fix
from Linus Lüssing.
9) Fix chip hang in qede driver, from Sudarsana Reddy Kalluru.
10) Fix missing setting of encapsulation before inner handling completes
in udp_offload code, from Jarno Rajahalme.
11) Missing rollbacks during LAG join and flood configuration failures
in mlxsw driver, from Ido Schimmel.
12) Fix error code checks in netxen driver, from Dan Carpenter.
13) Fix key size in new macsec driver, from Sabrina Dubroca.
14) Fix mlx5/VXLAN dependencies, from Arnd Bergmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net/mlx5e: make VXLAN support conditional
Revert "net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue"
macsec: key identifier is 128 bits, not 64
Documentation/networking: more accurate LCO explanation
macvtap: segmented packet is consumed
tools: bpf_jit_disasm: check for klogctl failure
qede: uninitialized variable in qede_start_xmit()
netxen: netxen_rom_fast_read() doesn't return -1
netxen: reversed condition in netxen_nic_set_link_parameters()
netxen: fix error handling in netxen_get_flash_block()
mlxsw: spectrum: Add missing rollback in flood configuration
mlxsw: spectrum: Fix rollback order in LAG join failure
udp_offload: Set encapsulation before inner completes.
udp_tunnel: Remove redundant udp_tunnel_gro_complete().
qede: prevent chip hang when increasing channels
net: ipv6: tcp reset, icmp need to consider L3 domain
bridge: fix igmp / mld query parsing
net: bridge: fix old ioctl unlocked net device walk
VSOCK: do not disconnect socket when peer has shutdown SEND only
net/mlx4_en: Fix endianness bug in IPV6 csum calculation
...
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following large patchset contains Netfilter updates for your
net-next tree. My initial intention was to send you this in two goes but
when I looked back twice I already had this burden on top of me.
Several updates for IPVS from Marco Angaroni:
1) Allow SIP connections originating from real-servers to be load
balanced by the SIP persistence engine as is already implemented
in the other direction.
2) Release connections immediately for One-packet-scheduling (OPS)
in IPVS, instead of making it via timer and rcu callback.
3) Skip deleting conntracks for each one packet in OPS, and don't call
nf_conntrack_alter_reply() since no reply is expected.
4) Enable drop on exhaustion for OPS + SIP persistence.
Miscelaneous conntrack updates from Florian Westphal, including fix for
hash resize:
5) Move conntrack generation counter out of conntrack pernet structure
since this is only used by the init_ns to allow hash resizing.
6) Use get_random_once() from packet path to collect hash random seed
instead of our compound.
7) Don't disable BH from ____nf_conntrack_find() for statistics,
use NF_CT_STAT_INC_ATOMIC() instead.
8) Fix lookup race during conntrack hash resizing.
9) Introduce clash resolution on conntrack insertion for connectionless
protocol.
Then, Florian's netns rework to get rid of per-netns conntrack table,
thus we use one single table for them all. There was consensus on this
change during the NFWS 2015 and, on top of that, it has recently been
pointed as a source of multiple problems from unpriviledged netns:
11) Use a single conntrack hashtable for all namespaces. Include netns
in object comparisons and make it part of the hash calculation.
Adapt early_drop() to consider netns.
12) Use single expectation and NAT hashtable for all namespaces.
13) Use a single slab cache for all namespaces for conntrack objects.
14) Skip full table scanning from nf_ct_iterate_cleanup() if the pernet
conntrack counter tells us the table is empty (ie. equals zero).
Fixes for nf_tables interval set element handling, support to set
conntrack connlabels and allow set names up to 32 bytes.
15) Parse element flags from element deletion path and pass it up to the
backend set implementation.
16) Allow adjacent intervals in the rbtree set type for dynamic interval
updates.
17) Add support to set connlabel from nf_tables, from Florian Westphal.
18) Allow set names up to 32 bytes in nf_tables.
Several x_tables fixes and updates:
19) Fix incorrect use of IS_ERR_VALUE() in x_tables, original patch
from Andrzej Hajda.
And finally, miscelaneous netfilter updates such as:
20) Disable automatic helper assignment by default. Note this proc knob
was introduced by a900689264 ("netfilter: nf_ct_helper: allow to
disable automatic helper assignment") 4 years ago to start moving
towards explicit conntrack helper configuration via iptables CT
target.
21) Get rid of obsolete and inconsistent debugging instrumentation
in x_tables.
22) Remove unnecessary check for null after ip6_route_output().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc support for __builtin_bswap16() was supposedly added for powerpc in
gcc 4.6, and was then later added for other architectures in gcc 4.8.
However, Stephen Rothwell reported that attempting to use it on powerpc
in gcc 4.6 fails with:
lib/vsprintf.c:160:2: error: initializer element is not constant
lib/vsprintf.c:160:2: error: (near initialization for 'decpair[0]')
lib/vsprintf.c:160:2: error: initializer element is not constant
lib/vsprintf.c:160:2: error: (near initialization for 'decpair[1]')
...
I'm not entirely sure what those errors mean, but I don't see them on
gcc 4.8. So let's consider gcc 4.8 to be the official starting point
for __builtin_bswap16().
Arnd Bergmann adds:
"I found the commit in gcc-4.8 that replaced the powerpc-specific
implementation of __builtin_bswap16 with an architecture-independent
one. Apparently the powerpc version (gcc-4.6 and 4.7) just mapped to
the lhbrx/sthbrx instructions, so it ended up not being a constant,
though the intent of the patch was mainly to add support for the
builtin to x86:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=52624
has the patch that went into gcc-4.8 and more information."
Fixes: 7322dd755e ("byteswap: try to avoid __builtin_constant_p gcc bug")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: turn into monolithic driver
This patchset merges all mv88e6* drivers supported by the shared
mv88e6xxx code into a single mv88e6xxx DSA switch driver.
Some flags are added to describe the capabilities of a switch model,
such as the presence of a PPU, EEPROM, some old or new registers, etc.
First these flags are used to conditionally support the same set of
functions in every driver, then specific driver files are removed in
favor of the common mv88e6xxx driver.
Only the merge of driver specific setup code assumes a few differences.
If these differences such as frames priorities are really needed for
some models, they can easily be brought back in a future patch.
Some inconsistencies might show up, such as the need for
MV88E6XXX_FLAG_PPU and MV88E6XXX_FLAG_PPU_ACTIVE flags. But this
patchset does not aim to fix them yet. A future patch can do that if
they end up being unwanted.
The patchset has been tested on interconnected 88E6352 and 88E6185.
Changes v1 -> v2:
- add missing MV88E6XXX_FLAG_EEPROM flag checks
- remove a few remaining _ prefixes
- remove MV88E6XXX_FLAG_CORE_TAG_TYPE which is a specific default
Changes RFC -> v1:
- introduce flags in a separate patch
- do not refactor anything yet
- do not add new functions prefixed with _
- drop packet discarding and mentioned tested platforms
- factorize family flags
- update text for NET_DSA_MV88E6XXX Kconfig entry
====================
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all drivers support the same set of functions and the same
setup code, drop every model-specific DSA switch driver and replace them
with a common mv88e6xxx driver.
This merges the info tables into one, removes the function exports, the
model-specific files, and update the defconfigs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6131 is the only driver to set the tag protocol to DSA_TAG_PROTO_DSA.
Since it works fine with DSA_TAG_PROTO_EDSA, change its value, like all
other mv88e6xxx drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a shared mv88e6xxx_setup function to the drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6131 is the only driver which setups the priority of IGMP/MLD snoop
frames and ARP frames to the highest setting. Drop such change until we
figure out a common configuration for all switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch models setup the GLOBAL_CONTROL_2 register with slightly
differences.
Since the cascade mode is valid even in a single chip setup, factorize
such configuration.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch drivers configure the GLOBAL_MONITOR_CONTROL register with
slightly changes.
Assume the setup of the upstream port, and configure it as the port to
which ingress and egress and ARP monitor frames are to be sent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6131 switch models have a Core Tag Type register. Their setup code
is setting it to 0x8100, which is the reset default.
Drop this specific part which is correctly configured on reset anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All switch models configure the GLOBAL_CONTROL register with slightly
differences.
Discarding packets with excessive collisions
(GLOBAL_CONTROL_DISCARD_EXCESS) is specific to 6352 and similar
switches, and setting a maximum frame size
(GLOBAL_CONTROL_MAX_FRAME_1632) is specific to 6185 and similar
switches.
As we are centralizing the chips setup, skip these settings and don't
discard any frames yet, until we found out that such discarding by the
hardware is necessary.
Assume a common setup to enable the PHY Polling Unit if present, don't
discard any packets, and mask all interrupt sources.
Tested on 88E6352 and 88E6185.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every driver is calling mv88e6xxx_setup_global after
mv88e6xxx_setup_common. Call the former in the latter.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_PPU_ACTIVE flag to describe how to reset the
switch, and merge the reset call to the common setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_ATU flag to identify switch models with an Address
Translation Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_VTU flag to indentify switch models with a VLAN
Table Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MV88E6XXX_FLAG_PORTSTATE and MV88E6XXX_FLAG_VLANTABLE flags to
identify switch models with required 802.1D operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only 6131 was not supporting the port registers access yet. Assume such
support and use the unlock access routines in the meantime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_EEE flag to describe switch models featuring Energy
Efficient Ethernet. Use it to conditionally support such access in the
common code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch models have a dedicated register for Switch MAC/WoF/WoL.
This register, when present, is used to indirectly set the switch MAC
address, instead of a direct write to 3 global registers.
Identify this feature and share a common mv88e6xxx_set_addr function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MV88E6XXX_FLAG_TEMP and MV88E6XXX_FLAG_TEMP_LIMIT flags to describe
switch models featuring a temperature access. Use them to centralize the
access to the temperature feature.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_EEPROM flag to describe switch models featuring an
EEPROM and distribute the EEPROM access routines to all models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch has dedicated SMI PHY Command and Data registers, used to
indirectly access the PHYs, instead of direct access.
Identify these switch models and make mv88e6xxx_phy_{read,write} generic
enough to support every models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a MV88E6XXX_FLAG_PPU flag to describe switch models with a PHY
Polling Unit. This allows to merge PPU specific PHY access code in the
share code.
Make the mv88e6xxx_ppu_disable and mv88e6xxx_phy_{read,write}_ppu
functions use unlocked register accesses in order to call them in
mv88e6xxx_phy_{read,write} in a locked context.
Since the PPU code is shared, also remove NET_DSA_MV88E6XXX_NEED_PPU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flags bitmap to the info structure in order to identify features
supported or not by the different switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier patch changed lookup side to also net_eq() namespaces after
obtaining a reference on the conntrack, so a single kmemcache can be used.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We already include netns address in the hash, so we only need to use
net_eq in find_appropriate_src and can then put all entries into
same table.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Will be needed soon when we place all in the same hash table.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The updated specification for the IFI CANFD core contains description
of more detailed error reporting capability of the core. Implement
support for this detailed error reporting.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Only increment the TX counters in the irq handler if a CAN message
was sent. The current code incremented the counters also if the TX
FIFO empty interrupt happened, which is incorrect.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN_CTRLMODE_FD flag is set for both ISO and BOSCH CANFD mode,
while the CAN_CTRLMODE_FD_NON_ISO is additional flag which is only
set for CANFD-BOSCH mode. Fix the handling of the flags to reflect
this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no distinction between bittiming constants for the slow and
fast part of the CANFD operation on this controller, so just use one
single bittiming constant set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The updated documentation regarding the IFI CANFD core from April 2016
adds more details regarding the timing calculation. There is no longer
any distinction in the timing calculation between CANFD and CAN2.0, but
instead there are two timing modes -- 4_12_6_6 and 7_9_8_8 -- where the
numbers mean the width in bits of the SJW/Prescaler/TimeA/TimeB fields.
The code uses 7_9_8_8 mode, which allows more fine-grained control over
the timing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Start the NAPI polling in case the bus warning interrupt happens,
since it is the poll function which checks and reports the warning.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
